Search NASA⌕ Search

SEARCH · Search NASA

Results for “interfacial stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Structural Evolution and Stability of Rh/TiO 2 Catalysts under CO 2 Hydrogenation Conditions: Influence of the Initial Rh Structure

Characterizing catalyst stability by identifying the predominant mechanisms, timescales and driving forces of catalyst reconstruction under relevant reaction conditions is necessary for the design and commercialization of new catalysts. Here, in this paper, we study Rh/TiO 2 catalysts under CO 2 hydrogenation conditions (773 K, 75% H 2 , 25% CO 2 ) at high conversion and utilize reactivity studies along with ex-situ and in-situ spectroscopy and microscopy to characterize changes in catalyst activity and structure as a function of time on stream and the initial catalyst structure. This is a prototypical catalyst for CO 2 hydrogenation where Rh structure and Rh-TiO 2 interactions have been proposed to explain reactivity, selectivity (between CO and CH 4 formation) and catalyst stability. The influence of the initial Rh structure (varying from Rh single atoms to Rh nanoparticles), support stability, regeneration and pretreatment(s), and the chemical potential(s) of the reaction environment on reaction selectivity and catalyst stability were explored. The product selectivity between CO and CH 4 was determined to be dependent on the relative fraction of Rh single atoms and Rh nanoparticle-TiO 2 interfacial sites under reaction conditions, each exhibiting distinct stability under prolonged time on stream. Surprisingly, Rh single atoms exhibited stability for the duration of 90 h reactivity measurements, even at high Rh density (≥ 1.8 Rh atoms/nm 2 ) on the support, while Rh nanoparticles sintered under reaction conditions. As a result, all catalysts exhibited increasing selectivity to CO with increasing time on stream (> 10 h). We conclude the distribution of Rh structures evolved over time under reaction conditions through three distinct reconstruction mechanisms (Rh particle fragmentation, Ostwald ripening, and particle migration and coalescence) that occurred on varying timescales. Catalyst stability on the ~90 h time scale was ultimately controlled by the initial Rh structure.

25 ENERGY STORAGE↗
DOE OSTI2025

Epitaxial Growth of 2D Core‐Crown SnS 2 /SnSe 2 Heterostructure Through Interfacial Modification with Polyvinylpyrrolidone

Abstract Developing generalized strategies for controlled synthesis of 2D heterostructures remains a significant challenge because the existing approaches often suffer from poor reproducibility and scalability. In this study, a solution synthesis approach for epitaxial core‐crown heterostructures with controlled band alignment, that overcomes these challenges is reported. Polyvinylpyrrolidone (PVP) is used as a structure‐directing agent to reduce lattice mismatch between SnS 2 and SnSe 2 (10‐10) surfaces and direct epitaxial growth of SnSe 2 crown on SnS 2 seed. Additionally, PVP adsorption to the basal plane prevents van der Waals stacking and stabilizes 2D heterostructures during synthesis. Driven by interfacial thermodynamics, the formation of the core‐crown heterostructure is highly reproducible and the size of the 2D heterostructure and relative areas of the core and the crown can be precisely controlled in a two‐step process by varying synthesis times for the seed and the crown. The identified growth pathway for 2D heterostructures can be generalized to other combinations of van der Waals materials to provide a platform for synthesizing micron‐size epitaxial heterostructures with a desired electronic structure for catalysis and microelectronics.

Liu, Lili [Physical and Computational Sciences Dir↗
DOE OSTI2024

One-Step Synthesis and Operando Electrochemical Impedance Spectroscopic Characterization of Heterostructured MoP–Mo 2 N Electrocatalysts for Stable Hydrogen Evolution Reaction

Here this study presents a novel synthesis of self-standing MoP and Mo 2 N heterostructured electrocatalysts with enhanced stability and catalytic performance. Facilitated by the controlled phase and interfacial microstructure, the seamless structures of these catalysts minimize internal resistivity and prevent local corrosion, contributing to increased stability. The chemical synthesis proceeds with etching step to activate the surface, followed by phosphor-nitriding in a chemical vapor deposition chamber to produce MoP-Mo 2 N@Mo heterostructured electrocatalysts. X-ray diffraction analyses confirm the presence of MoP, Mo 2 N, and Mo phases in the electrocatalyst. Morphology studies using scanning electron microscopy characterizes the hierarchical growth of structures, indicating successful formation of the heterostructure. X-ray photoelectron spectroscopy (XPS) analyses of the as-synthesized and post-catalytic activity samples reveal the chemical shift in terms of binding energy (BE) of Mo 3d XPS peak, especially after catalytic activity. The XPS BE shifts attributed to changes in oxidation state, electron transfer, and surface reconstruction during catalysis. Electrochemical evaluation of the catalysts demonstrates the superior performance of the MoP-Mo 2 N@Mo heterostructured catalyst in hydrogen evolution reactions (HER), with lower overpotentials and enhanced Tafel slopes. Stability tests reveal changes in double layer capacitance over time, suggesting surface reconstruction and increased active surface area during catalysis. Operando electrochemical impedance spectroscopy (EIS) further elucidates the dynamic changes in resistance and charge transfer during HER. Overall, comprehensive understanding of the synthesis, characterization, and electrochemical behavior of the developed MoP-Mo 2 N@Mo heterostructured electrocatalyst as presented in this paper highlights their potential utilization in sustainable energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Tailoring Interfaces in Solid-State Batteries Using Interfacial Thermochemistry and Band Alignment

Solid-state lithium ion batteries have enhanced thermal stability compared to batteries using liquid electrolytes. Although their practical implementation is limited by undesired side reactions between the electrode and electrolyte, different modification strategies have been proposed to stabilize these reactive interfaces. These approaches have been primarily based upon bulk materials properties, however, which may not necessarily be representative of the chemistry at the solid/solid interface. In this work, first principles calculations and X-ray scattering experiments are used to elucidate molecular-level reactivity and develop design principles for tailored interfaces based on surface and interfacial properties. Because of its well-known instability, the interface between the Li metal anode and the lithium lanthanum titanate (LLTO) solid electrolyte is applied as a model system. Density functional theory calculations are used to describe bulk, surface, and interfacial thermochemistry of the Li/LLTO system, and interfacial reconstruction is probed using ab initio molecular dynamics. These simulations of the Li/LLTO interface demonstrate facile decomposition concomitant with reduction of Ti 4+ ions. Based on further insights from computational analysis of the surface band edge positions, La 2 O 3 is proposed as an interlayer coating and is shown to provide an energetic barrier for interfacial charge transfer and decomposition reactions from X-ray reflectivity measurements and theoretical calculations. The findings in this work suggest that design strategies based on surface and interfacial properties can be used to kinetically stabilize electrode/electrolyte interfaces in solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Triiodide Attacks the Organic Cation in Hybrid Lead Halide Perovskites: Mechanism and Suppression

Molecular I 2 can be produced from iodide-based lead perovskites under thermal stress; triiodide, I 3 − , is formed from this I 2 and I − . Triiodide attacks protic cation MA + - or FA + -based lead halide perovskites (MA + , methylammonium; FA + , formamidinium) as explicated through solution-based nuclear magnetic resonance (NMR) studies: triiodide has strong hydrogen-bonding affinity for MA + or FA + , which leads to their deprotonation and perovskite decomposition. Triiodide is a catalyst for this decomposition that can be obviated through perovskite surface treatment with thiol reducing agents. In contrast to methods using thiol incorporation into perovskite precursor solutions, no penetration of the thiol into the bulk perovskite is observed, yet its surface application stabilizes the perovskite against triiodide-mediated thermal stress. Thiol applied to the interface between FAPbI 3 and Spiro-OMeTAD (“Spiro”) prevents oxidized iodine species penetration into Spiro and thus preserves its hole-transport efficacy. Surface-applied thiol affects the perovskite work function; it ameliorates hole injection into the Spiro overlayer, thus improving device performance. It helps to increase interfacial adhesion (“wetting”): fewer voids are observed at the Spiro/perovskite interface if thiols are applied. Perovskite solar cells (PSCs) incorporating interfacial thiol treatment maintain over 80% of their initial power conversion efficiency (PCE) after 300 h of 85 °C thermal stress.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tuning interfacial Dzyaloshinskii-Moriya interactions in thin amorphous ferrimagnetic alloys

Skyrmions can be stabilized in magnetic systems with broken inversion symmetry and chiral interactions, such as Dzyaloshinskii-Moriya interactions (DMI). Further, compensation of magnetic moments in ferrimagnetic materials can significantly reduce magnetic dipolar interactions, which tend to favor large skyrmions. Tuning DMI is essential to control skyrmion properties, with symmetry breaking at interfaces offering the greatest flexibility. However, in contrast to the ferromagnet case, few studies have investigated interfacial DMI in ferrimagnets. Here we present a systematic study of DMI in ferrimagnetic CoGd films by Brillouin light scattering. We demonstrate the ability to control DMI by the CoGd cap layer composition, the stack symmetry and the ferrimagnetic layer thickness. The DMI thickness dependence confirms its interfacial nature. In addition, magnetic force microscopy reveals the ability to tune DMI in a range that stabilizes sub-100 nm skyrmions at room temperature in zero field. Our work opens new paths for controlling interfacial DMI in ferrimagnets to nucleate and manipulate skyrmions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2004

Two-Fluid Models and Interfacial Area Transport in Microgravity Condition

The objective of the present study is to develop a two-fluid model formulation with interfacial area transport equation applicable for microgravity conditions. The new model is expected to make a leapfrog improvement by furnishing the constitutive relations for the interfacial interaction terms with the interfacial area transport equation, which can dynamically model the changes of the interfacial structures. In the first year of this three-year project supported by the U.S. NASA, Office of Biological and Physics Research, the primary focus is to design and construct a ground-based, microgravity two-phase flow simulation facility, in which two immiscible fluids with close density will be used. In predicting the two-phase flow behaviors in any two-phase flow system, the interfacial transfer terms are among the most essential factors in the modeling. These interfacial transfer terms in a two-fluid model specify the rate of phase change, momentum exchange, and energy transfer at the interface between the two phases. For the two-phase flow under the microgravity condition, the stability of the fluid particle interface and the interfacial structures are quite different from those under normal gravity condition. The flow structure may not reach an equilibrium condition and the two fluids may be loosely coupled such that the inertia terms of each fluid should be considered separately by use of the two-fluid model. Previous studies indicated that, unless phase-interaction terms are accurately modeled in the two-fluid model, the complex modeling does not necessarily warrant an accurate solution.

Ishii, Mamoru↗
NASA NTRS2002

Stability and Heat Transfer Characteristics of Condensing Films

The overall objective of this research is to investigate the fundamental physics of film condensation in reduced gravity. The condensation of vapor on a cool surface is important in many engineering problems,including spacecraft thermal control and also the behavior of condensate films that may form on the interior surfaces of spacecraft. To examine the effects of body force on condensing films, two different geometries have been tested in the laboratory: (1) a stabilizing gravitational body force (+1g, or condensing surface facing 'upwards') and (2) de-stabilizing gravitational body force (-1g, or 'downwards'). For each geometry, different fluid configurations are employed to help isolate the fluid mechanical and thermal mechanisms operative in condensing films. The fluid configurations are (a) a condensing film, and (b) a non-condensing film with film growth by mass addition by through the plate surface. Condensation experiments are conducted in a test cell containing a cooled copper or brass plate with an exposed diameter of 12.7 cm. The metal surface is polished to allow for double-pass shadowgraph imaging, and the test surface is instrumented with imbedded heat transfer gauges and thermocouples. Representative shadowgraph images of a condensing, unstable (-1g) n-pentane film are shown. The interfacial disturbances associated with the de-stabilizing body force leading to droplet formation and break-off can be clearly seen. The heat transfer coefficient associated with the condensing film is shown. The heat transfer coefficient is seen to initially decrease, consistent with the increased thermal resistance due to layer growth. For sufficiently long time, a steady value of heat transfer is observed, accompanied by continuous droplet formation and break-off. The non-condensing cell consists of a stack of thin stainless steel disks 10 cm in diameter mounted in a brass enclosure. The disks are perforated with a regular pattern of 361 holes each 0.25 mm in diameter. Non-condensing experiments in -1g have employed 50 cSt and 125 cSt silicone oil pumped through the perforated disks at a specified rate by a syringe micropump. The time to droplet break-off and the disturbance wavelengths appear to decrease with increasing pumping rate. The ability to reliably perform multi-point, ultrasonic measurements of the film thickness has been demonstrated. A linear array of eight transducers of 6 mm diameter (with a beam footprint of comparable size) are pulsed with a square-wave signal at a frequency of 5 MHz and a pulse duration of approximately 0.3 s. For thin films (60 m to 2-3 mm in thickness) the layer thickness is determined by frequency analysis, where the received ultrasound pulse is Fourier transformed and the spacing between the peaks in the frequency spectrum is analyzed. For thicker layers (up to at least 1 cm in thickness), time-domain analysis is performed of the received ultrasound pulses to generate directly the layer thickness. A time-trace of the film thickness at a point using a single transducer in the linear array is shown for the case of an unstable (-1g) n-pentane film. The oscillations in film thickness are evidently due to the passage and/or shedding of droplets from the cooled plate surface. The entire transducer array was used to measure the changes in film thickness resulting from the passage of gravity waves generated either by an oscillating wall or the impact of a single droplet on the free surface of a film. The enclosure in both cases was 14 cm square and the transducer spacing was 12 mm. Best results were obtained using as test fluid a mixture of 50% glycerol and 50% water with a fluid layer thickness of 3-5 mm. In both cases the measured wavelengths and wave propagation speeds using the ultrasound technique compared reasonably well with those observed by optical imaging. Additional information can be found in the original extended abstract.

Hermanson, J. C.↗
DOE OSTI2020

An epoxy-reinforced ceramic sheet as a durable solid electrolyte for solid state Na-ion batteries

In a conventional Na-ion battery system using liquid electrolyte, there are critical safety issues due to the instability of the liquid electrolyte. Na 3 Zr 2 Si 2 PO 12 (NASICON) solid electrolyte is a material that is sufficient to replace a liquid electrolyte as it has high ionic conductivity and thermal and electrochemical stability. However, as there is a large interfacial resistance in the NASICON solid electrolyte powder, even when used in combination with a polymer electrolyte, the advantageous effects of ceramics are not easily exhibited. In this study, we propose a top-down method of combining a polymer with a ceramic in which an ion transport channel is previously formed. In this method, a NASICON solid electrolyte is partially sintered to form ion transport channels. Then the NASICON solid electrolyte pores are filled with an epoxy polymer to increase the strength of the epoxy-NASICON composite electrolyte. This method demonstrates the possibility of our composite electrolyte being used as a thin and strong film. As a result of our methods, the ionic conductivity and thermal and electrochemical stability of NASICON were maintained, while the physical strength was enhanced by approximately 2 times. In addition, a capacity of 120 mA h g -1 and stability of 20 cycles were confirmed in a half cell with a Na 3 V 2 (PO 4 ) 3 cathode and Na metal. This method proposes a new direction for research regarding composite electrolytes created using an oxide-based solid electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2022

Benchmarking Solid-State Batteries Containing Sulfide Separators: Effects of Electrode Composition and Stack Pressure

Integrating sulfide separators into solid-state batteries (SSBs) containing high energy cathodes typically requires one or more materials and engineering solutions including: (i) applying interfacial coatings to mitigate electrolyte decomposition, (ii) applying high stack pressures to form robust solid-solid contacts, and (iii) using alloying anodes to avoid Li dendrite formation. Despite the promise of these approaches, a lack of standardized testing protocols makes it difficult to directly compare results among different studies. To address this problem, the present work benchmarks the performance of SSBs containing β-Li 3 PS 4 (LPS) separators and composite cathodes. By systematically varying the anode/cathode composition and stack pressure, this work demonstrates that cathode design is a major bottleneck for solid-state cells cycled at low rates (<100 µA cm -2 ). Operando stack pressure measurements show that, while mechanical confinement generally promotes higher active material utilization and cycling stability, this strategy alone does not address interfacial reactivity between LPS and high voltage cathodes. Here, these results also demonstrate that stress evolution during cycling is dominated by volume changes at the Li metal anode. Finally, we show that FeS 2 cathodes with moderate operating voltages (<3 V vs Li/Li + ) exhibit superior cycling performance compared to high voltage cathodes by facilitating formation of stable cathode/electrolyte interfaces.

25 ENERGY STORAGE↗
DOE OSTI2026

Selective Bidentate Coordination Reconstructs Residual PbI 2 to Homogenize Interfacial Energetics in Perovskite Solar Cells

Spatially heterogeneous interfacial energetics, often originating from residual lead iodide (PbI 2 ), represent a fundamental bottleneck to both the efficiency and operational stability of perovskite photovoltaics. Conventional PbI 2 passivation strategies based on monodentate ligands or highly polar solvents either interact weakly with PbI 2 or undesirably perturb the underlying three-dimensional perovskite lattice. Here, we report a diammonium bidentate strategy that selectively reconstructs residual PbI 2 into corner-sharing PbI 6 octahedra while preserving the bulk perovskite. Enabled by dual-site coordination, a newly designed thiophene-based bidentate ligand (MeXT) stabilizes PbI 6 units during passivation and establishes spatially homogeneous interfacial energetics. Perovskite solar cells incorporating MeXT achieve 26.19% power conversion efficiency and retain over 80% of their initial efficiency after 1000 h of continuous 1-sun illumination at 75 °C. This dual-anchor coordination passivation strategy establishes a general design principle for selectively treating residual PbI 2 and creating electronically coherent and operationally stable interfaces in perovskite photovoltaics.

ligands↗
NASA NTRS1993

On the shear stabilization of capillary break-up of finite liquid bridges

In this paper we consider an isothermal finite liquid bridge under zero-gravity. A sinusoidal interfacial shear stress drives a nonparallel flow in the bridge. The linear stability of this flow to three-dimensional disturbances (which may deform the cylindrical gas-liquid interface) is determined numerically by solving an elliptic eigenvalue problem. Previous results on shear stabilization of capillary break-up of axially unbounded cylindrical interfaces containing a parallel flow are hereby extended to a nonparallel flow. The turning flow regions influence the stability significantly. However, for the particular cases considered, a small area in parameter space remains where the capillary instability is suppressed through interfacial shear. Second, non-axisymmetric oscillatory instabilities are found which originate from an interaction of the interface deformation and the basic flow. These instabilities may be the isothermal limit of the oscillatory instabilities observed in float-zone crystal growth.

Dijkstra, Henk A.↗
DOE OSTI2024

Epitaxial heterointerfacial electron bridge synchronizes oxygen evolution activity and stability on a layered double hydroxide surface

Scalable green hydrogen production via electrocatalytic water splitting is largely restricted by the insufficient activity and stability of oxygen evolution reaction (OER) catalysts at the anode. As a class of the most active OER catalysts in alkaline electrolyzers, the application of layered double hydroxides (LDHs) remains a main challenge owing to the unstable lattice oxygen dissolution due to the dominant lattice oxygen-involving OER mechanism during long-term operation. Herein, we found that using an epitaxial hetero-interfacing nickel hydroxide (namely Ni(OH) 2 ) as an electron bridge between an active FeCo LDH and Ni foam support to form an LDH*/NFO catalyst, the electronic storage capacity around the Fermi level (-0.5 to +0.5 eV, e-D FE ) sharply increases from 0.93 per cell to 1.51 per cell. Subsequently, we demonstrate that this high e-D FE enables ceaseless and fast power injection into the kinetic process of intermediate species conversion and inhibits lattice oxygen dissolution in the active FeCo LDH. Consequently, it demonstrated a low OER overpotential of 246 mV at a current density of 100 mA cm -2 and ultrahigh stability for up to 3500 hours with an ultraslow overpotential increase rate of 9.4 × 10 -3 mV h -1 . Therefore, we developed an epitaxial hetero-interfacial electron bridging strategy to synchronize the activity and stability of available catalysts for scalable green hydrogen production via electrocatalytic water splitting.

25 ENERGY STORAGE↗
DOE OSTI2024

Lamination of >21% Efficient Perovskite Solar Cells with Independent Process Control of Transport Layers and Interfaces

Transport layer and interface optimization is critical for improving the performance and stability of perovskite solar cells (PSCs) but is restricted by the conventional fabrication approach of sequential layer deposition. While the bottom transport layer is processed with minimum constraints, the narrow thermal and chemical stability window of the halide perovskite (HP) layer severely restricts the choice of top transport layer and its processing conditions. To overcome these limitations, we demonstrate lamination of HPs—where two transport layer-perovskite half-stacks are independently processed and diffusion-bonded at the HP-HP interface—as an alternative fabrication strategy that enables self-encapsulated solar cells. Power conversion efficiencies (PCE) of >21% are realized using cells that incorporate a novel transport layer combination along with dual-interface passivation via self-assembled monolayers, both of which are uniquely enabled by the lamination approach. This is the highest reported PCE for any laminated PSC encapsulated between glass substrates. We further show that this approach expands the processing window beyond traditional fabrication processes and is adaptable for different transport layer compositions. The laminated PSCs retained >75% of their initial PCE after 1000 h of 1-sun illumination at 40 °C in air using an all-inorganic transport layer configuration without additional encapsulation. Furthermore, a laminated 1 cm 2 device maintained a V oc of 1.16 V. Finally, the scalable lamination strategy in this study enables the implementation of new transport layers and interfacial engineering approaches for improving performance and stability.

14 SOLAR ENERGY↗
DOE OSTI2023

Uniform momentum and temperature zones in unstably stratified turbulent flows

Wall-bounded turbulent flows exhibit a zonal arrangement, in which streamwise velocity organizes into uniform momentum zones (UMZs), separated by thin layers of elevated interfacial shear. While significant research efforts have focused on these structural features in neutrally stratified flows, the effects of unstable thermal stratification on UMZs and on analogous uniform temperature zones (UTZs) have not been considered previously. In this article, statistical properties of UMZs and UTZs are investigated using a suite of large eddy simulations of unstably stratified turbulent channel flow spanning weakly to highly convective conditions. When normalized by the friction velocity and stability-dependent mixing length, the mean velocity gradient based on UMZ interfacial velocity jumps and the vorticity thickness exhibits good collapse for all stabilities, establishing a link between UMZ properties and scaling predictions from Monin–Obukhov similarity theory. A similar relationship is found between UTZ properties and surface-layer scaling of the mean temperature gradient. In the mixed layer, mean UMZ depth is quasi-constant with wall-normal distance, while the deepest UTZs are found in the centre of the boundary layer. These instantaneous structures are found to be linked to the well-mixed velocity and temperature profiles in the convective mixed layer. Conditional averaging indicates that both UMZ and UTZ interfaces are associated with ejections of momentum and warm updrafts below the interface and sweeps of momentum and cool downdrafts above the interface. These results demonstrate a tangible connection between instantaneous structural features, mean properties and scaling laws in unstably stratified flows.

Mechanics↗
DOE OSTI2021

Nanoparticle/Polyelectrolyte Complexes for Biomimetic Constructs

Abstract Constructing all‐aqueous systems with tailored geometries can generate a new class of biomimetic materials, a fascinating but challenging goal to achieve. Here, by taking advantage of the interfacial complexation of a polyelectrolyte (PE) and cellulose nanocrystals (CNCs), a unique interfacial PE/CNC complex is demonstrated for the stabilization of aqueous two‐phase systems and for the fabrication of all‐aqueous double emulsions and 3D constructs. The thickness of PE/CNC complex can be effectively adjusted by tuning the osmotic stress imbalance between the two aqueous phases and, during the formation and thickening of PE/CNC complex, individual assemblies can be connected to design hierarchical all‐aqueous structures. This new platform affords tremendous potential for engineering biomimetic constructs with advanced functionality, that can be used for chemical separation, delivery, and biphasic cascading reaction vessels.

Yin, Yixuan↗
DOE OSTI2025

Achieving Electrode Smoothing by Controlling the Nucleation Phase of Metal Deposition Through Polymer‐Substrate Binding

Polymer additives [like polyethylene oxide (PEO)] are widely used for smooth electrode deposition in aqueous zinc and many other battery systems. However, the precise mechanism by which they regulate morphology and suppress dendrite formation remains unclear. In this study, the knowledge gap is addressed by using in situ electrochemical atomic force microscopy to directly observe the interfacial evolution during Zn electrodeposition and polymer adsorption on Cu substrates in the presence of varying concentrations of ZnSO 4 and PEO. Contrary to previous literature assumptions, which emphasize the binding to the growing Zn crystal surfaces or Zn 2+ ions, the results demonstrate that PEO smooths Zn films by promoting nucleation of (002)-oriented Zn platelets through interactions with the Cu substrate. Density functional theory simulations support this finding by showing that PEO adsorption on Cu modifies the interfacial energy of Zn/Cu/electrolyte interfaces, favoring the stabilization of Zn (002) on the Cu substrate, as well as confines Zn electrodeposition to a narrow near-surface region. In conclusion, these findings elucidate a novel design principle for electrode smoothing, emphasizing the importance of substrate selection paired with polymer additives that exhibit an attractive interaction with the substrate but minimal interaction with growing crystals, offering a mechanistic perspective for improved battery performance.

Electrodeposition↗
DOE OSTI2025

Interface‐Induced Stability of Nontrivial Topological Spin Textures: Unveiling Room‐Temperature Hopfions and Skyrmions

Topological spin configurations, such as soliton-like spin texture and Dirac electron assemblies, have recently emerged in fundamental science and technology. Achieving stable topological spin textures at room temperature is crucial for their use as long-range information carriers. However, their creation and manipulation are hindered by multi-step field training and competing interactions. Thus, a spontaneous ground state for multidimensional topological spin textures is desirable, with skyrmions forming swirling, hedgehog-like spin structures in two dimensions and hopfions as their twisted 3D counterparts. Here, the first observation of robust and reproducible topological spin textures of hopfions and skyrmions observed at room temperature and in zero magnetic field is reported, which are stabilized by geometric confinement and protected by interfacial magnetism in a ferromagnet/topological insulator/ferromagnet trilayer heterostructure. These skyrmion-hopfion configurations are directly observed at room temperature with Lorenz transmission electron microscopy. Using micromagnetic modeling, the experimental observations of hopfion-skyrmion assemblies are reproduced. This model reveals a complete picture of how spontaneously organized skyrmion lattices encircled by hopfion rings are controlled by surface electrons, uniaxial anisotropy, and Dzyaloshinskii-Moriya interaction. This study provides evidence that topological chiral spin textures can facilitate the development of magnetic topological carriers, paving the way for ultralow-power and high-density information processing.

hopfions↗