Search NASA⌕ Search

SEARCH · Search NASA

Results for “land simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

An in-flight simulation of approach and landing of a STOL transport with adverse ground effect

The results of an in-flight simulation program undertaken to study the problems of landing a representative STOL transport in the presence of adverse ground effects are presented. Landings were performed with variations in ground effect magnitude, ground effect lag, and thrust response. Other variations covered the effects of augmented lift response, SAS-failures, turbulence, segmented approach, and flare warning. The basic STOL airplane required coordinated use of both stick and throttle for consistently acceptable landings, and the presence of adverse ground effects made the task significantly more difficult. Ground effect lag and good engine response gave noticeable improvement, as did augmented lift response.

Ellis, D. R.↗
NASA NTRSDate not supplied

Multi-Model Monte Carlo Estimators for Trajectory Simulation

Predicting landing radius and other quantities of interest (QoI) for entry, descent, andlanding (EDL) applications requires a viable uncertainty propagation method for quantifying the impact of uncertainties in aerodynamics, atmosphere, mass properties, etc. While standard Monte Carlo (MC) simulation is the de facto standard for producing robust and unbiasedstatistical estimators, it is often infeasible for expensive, high-fidelity models. Low-fidelity models are commonly constructed to replace the high-fidelity model in MC simulation for computational speedup, but at the expense of accuracy and unbiasedness. Emerging multi-model MC methods are bridging this gap by combining predictions from two or more modelsof varying fidelity and computational cost for efficient and unbiased uncertainty propagation.This works establishes a proof of concept for using multi-model MC to increase the speed and precision of trajectory simulation for EDL. It is shown that combining a high-fidelity EDL model with low-fidelity models (e.g., data-driven, reduced physics) in this manner has the potential to yield significant efficiency and accuracy gains for certain EDL QoIs versusa standard MC approach. Moreover, the unbiasedness of multi-model MC predictions ishighlighted by showing increased accuracy versus an approach that leverages a low-fidelity model alone.

James E Warner↗
NASA NTRSDate not supplied

ADVANCES IN PLUME-SURFACE INTERACTION SIMULATION CAPABILITY UNDER LUNAR LANDING CONDITIONS

The Fluid Dynamics Branch at theNASA Marshall Space Flight Center has assembled a portfolio of simulation tools to predict Plume-SurfaceInteraction (PSI) environments during extra-terrestrial propulsive landings. Particular focus is on engineering support for lunar landers such as robotic CommercialLunar Payload Services (CLPS) and the HumanLander System (HLS). Extension of existing PSI simulation capabilities are required to accurately capture the complex plume flow conditions and surface soil particle composition effects that arise in the lunar environment. The required model development and implementation, and extensive verification and validation of the key simulation tools, Loci/Chem [1]and Loci/Boltzmann [2], and Loci/GGFS [3] are now performed under a NASA Space Technology MissionDirectorate (STMD) funded multi-year GameChanging Development (GCD) project. The project will implement and mature these new modeling features and verify and validate them for the Mars andMoon environments with the aid of existing and new experiments to be performed under this project

Plume Surface Interaction↗
NASA NTRS2017

Aeroacoustic Simulations of a Nose Landing Gear with FUN3D: A Grid Refinement Study

A systematic grid refinement study is presented for numerical simulations of a partially-dressed, cavity-closed (PDCC) nose landing gear configuration that was tested in the University of Florida's open-jet acoustic facility known as the UFAFF. The unstructured-grid flow solver FUN3D is used to compute the unsteady flow field for this configuration. Mixed-element grids generated using the Pointwise (Registered Trademark) grid generation software are used for numerical simulations. Particular care is taken to ensure quality cells and proper resolution in critical areas of interest in an effort to minimize errors introduced by numerical artifacts. A set of grids was generated in this manner to create a family of uniformly refined grids. The finest grid was then modified to coarsen the wall-normal spacing to create a grid suitable for the wall-function implementation in FUN3D code. A hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) turbulence modeling approach is used for these simulations. Time-averaged and instantaneous solutions obtained on these grids are compared with the measured data. These CFD solutions are used as input to a FfowcsWilliams-Hawkings (FW-H) noise propagation code to compute the farfield noise levels. The agreement of the computed results with the experimental data improves as the grid is refined.

Vatsa, Veer N.↗
NASA NTRS2017

A Comparative Study of Simulated and Measured Main Landing Gear Noise for Large Civil Transports

Computational results for the NASA 26%-scale model of a six-wheel main landing gear with and without a toboggan-shaped noise reduction fairing are presented. The model is a high-fidelity representation of a Boeing 777-200 aircraft main landing gear. A lattice Boltzmann method was used to simulate the unsteady flow around the model in isolation. The computations were conducted in free-air at a Mach number of 0.17, matching a recent acoustic test of the same gear model in the Virginia Tech Stability Wind Tunnel in its anechoic configuration. Results obtained on a set of grids with successively finer spatial resolution demonstrate the challenge in resolving/capturing the flow field for the smaller components of the gear and their associated interactions, and the resulting effects on the high-frequency segment of the farfield noise spectrum. Farfield noise spectra were computed based on an FWH integral approach, with simulated pressures on the model solid surfaces or flow-field data extracted on a set of permeable surfaces enclosing the model as input. Comparison of these spectra with microphone array measurements obtained in the tunnel indicated that, for the present complex gear model, the permeable surfaces provide a more accurate representation of farfield noise, suggesting that volumetric effects are not negligible. The present study also demonstrates that good agreement between simulated and measured farfield noise can be achieved if consistent post-processing is applied to both physical and synthetic pressure records at array microphone locations.

Konig, Benedikt↗
NASA NTRS1974

Flight test of an automatic approach and landing concept for a simulated space shuttle represented by the NASA Convair 990 aircraft

Unpowered automatic approaches and landings were conducted to study navigation, guidance, and control problems associated with terminal area, approach, and landing operation for the space shuttle. A Convair 990 aircraft was equipped with a digital flight-control computer connected to the aircraft control systems and displays. The flight tests evaluated, from 11,300 m to touchdown, the performance of a navigation and guidance concept that utilized blended radio/inertial navigation with VOR, DME, and ILS as the ground radio navigation aids. The results from 36 automatic approaches and landings are analyzed. Preliminary results indicate that this concept may provide sufficient accuracy that automatic landing of the unpowered shuttle orbiter can be accomplished on a conventional size runway.

Smith, D. W.↗
NASA NTRS2011

Impact of Optimized land Surface Parameters on the Land-Atmosphere Coupling in WRF Simulations of Dry and Wet Extremes

Land-atmosphere (L-A) interactions play a critical role in determining the diurnal evolution of both planetary boundary layer (PBL) and land surface temperature and moisture budgets, as well as controlling feedbacks with clouds and precipitation that lead to the persistence of dry and wet regimes. Recent efforts to quantify the strength of L-A coupling in prediction models have produced diagnostics that integrate across both the land and PBL components of the system. In this study, we examine the impact of improved specification of land surface states, anomalies, and fluxes on coupled WRF forecasts during the summers of extreme dry (2006) and wet (2007) conditions in the U.S. Southern Great Plains. The improved land initialization and surface flux parameterizations are obtained through the use of a new optimization and uncertainty module in NASA's Land Information System (LIS-OPT), whereby parameter sets are calibrated in the Noah land surface model and classified according to the land cover and soil type mapping of the observations and the full domain. The impact of the calibrated parameters on the a) spin up of land surface states used as initial conditions, and b) heat and moisture fluxes of the coupled (LIS-WRF) simulations are then assessed in terms of ambient weather, PBL budgets, and precipitation along with L-A coupling diagnostics. In addition, the sensitivity of this approach to the period of calibration (dry, wet, normal) is investigated. Finally, tradeoffs of computational tractability and scientific validity (e.g.,. relating to the representation of the spatial dependence of parameters) and the feasibility of calibrating to multiple observational datasets are also discussed.

Kumar, Sujay↗
NASA NTRS1987

Effect of motion cues during complex curved approach and landing tasks: A piloted simulation study

A piloted simulation study was conducted to examine the effect of motion cues using a high fidelity simulation of commercial aircraft during the performance of complex approach and landing tasks in the Microwave Landing System (MLS) signal environment. The data from these tests indicate that in a high complexity MLS approach task with moderate turbulence and wind, the pilot uses motion cues to improve path tracking performance. No significant differences in tracking accuracy were noted for the low and medium complexity tasks, regardless of the presence of motion cues. Higher control input rates were measured for all tasks when motion was used. Pilot eye scan, as measured by instrument dwell time, was faster when motion cues were used regardless of the complexity of the approach tasks. Pilot comments indicated a preference for motion. With motion cues, pilots appeared to work harder in all levels of task complexity and to improve tracking performance in the most complex approach task.

Scanlon, Charles H.↗
NASA NTRS1993

Numerical simulation of a powered-lift landing

The flow field about a delta wing equipped with thrust reverse jets in slow speed flight near the ground has been computed. Results include the prediction of the flow about the delta wing at four fixed heights above the ground, and simulated landing, in which the delta wing descends towards the ground. Comparison of computed and experimental lift coefficients indicates that the simulations can capture at least the qualitative trends in lift-loss encountered by thrust-vectoring aircraft operating in ground effect.

Chawla, Kalpana↗
NASA NTRS1981

Piloted simulation of hover and transition of a vertical attitude takeoff and landing aircraft

Piloted simulation studies of candidate control systems for VATOL aircraft were conducted on a six degree of freedom simulator. Hover and transitions from wing-born to hovering flight were performed, with and without turbulence, on a representative high performance fighter configuration. Deflection of the rear engine nozzle provided pitch and yaw control moments in concert with reaction controls for roll. Unique motion cues in hover result from the vertical displacement of the cockpit and the thrust vectoring nozzles. Abundant control power available with moderate engine nozzle deflection combined with rate feedback for stability augmentation provided very satisfactory control.

Hill, G. C.↗
NASA NTRS1976

Model and full-scale large transport airframe noise

Results are presented for an airframe noise experiment intended to obtain airframe noise data of a 0.03-scale model of a large transport aircraft in a flow facility for comparison with similar airframe noise data from full-scale flyover tests of the same aircraft. The test model simulated the landing and cruise configuration, including individual flap systems. Considerable noise is found to be associated with the extension of the model's leading edge flap system and to be reduced across the noise spectra when the gaps between the leading-edge flaps and the leading edge of the wing are sealed. Amplitude and frequency scaling relationships are developed which correlate respective data for a variety of aircraft configurations. Normalized model landing gear noise failed to simulate full-scale data.

Shearin, J. G.↗
NASA NTRS2020

A Simulation Framework for Precision Landing and Hazard Avoidance Technology Assessments

To meet NASA’s challenge to return humans to the Moon in 2024 and establish a sustainable presence in 2028 requires advances in autonomous spacecraft navigation. The Safe and Precise Landing Integrated Capabilities Evolution (SPLICE) project, which leverages previous work at NASA to develop multi-mission precision landing and hazard avoidance technologies, is using a multi-faceted approach to achieve the advanced landing requirements. In addition to increasing the technology readiness level of key sensors and developing high performance space computing, SPLICE uses simulations to determine navigation requirements and evaluate sensor performance. The effort evaluates various precision landing concepts of operations, not only for the lunar human and robotic missions, but also for potential missions to other solar system destinations. This paper summarizes the six degree-of-freedom high fidelity simulation framework, trajectory design methodology, and sensor models being considered for a variety of precision lander missions. Initial results of the navigation sensor performance for a human Mars mission are presented. Finally, trade and sensitivity studies are outlined for future work to fully characterize sensor performance assumptions and modifications required to achieve precision landing and hazard avoidance.

Alicia Dwyer Cianciolo↗
NASA NTRS2021

Quantifying the Observational Requirements of a Space-borne LiDAR Snow Mission

This study quantifies the level of observational accuracy required from a spaceborne light detection and ranging (LiDAR) snow depth retrieval mission for enabling beneficial impacts for snow estimation. The study is conducted over a region in Western Colorado using a suite of observing system simulation experiments(OSSEs).The Joint UK Land Environment Simulator, version 5.0 (JULES v5.0) is employed to simulate a suite of idealized LiDAR observations, considering a range of LiDAR snow depth retrieval errors, different hypothetical sensor swath widths, and the impact of cloud cover on observability. These simulated observations are then assimilated into the Noah land surface modelwith multi-parameterization options, version 3.6 (Noah-MP v3.6) model. This data assimilation setup is used to systematically evaluate the potential utility of LiDAR observations for improving modeled snow water equivalent (SWE)estimates and water budget variables such as runoff. Results from the OSSE runsshow that, in general, assimilation of synthetic LiDAR observations provide beneficial impacts when theLiDAR snow depth retrieval error standard deviation (σerror) is below 60 cm.Based on comparisons between the realistic (i.e., swath-limited and cloud-attenuated) case and the idealized (i.e., infinite swath width in the absence of cloud cover) case,this study concludes that observations with a conservative error standard deviation threshold of 40 cm (i.e., upper limit of the snow depth retrieval error that adds value to the SWE estimates viaassimilation) are needed for improving modeled snow estimates. More than a 33% reduction in SWEroot mean square errors and more than a 15% increase in correlation coefficientsare achieved when σ error ≤ 40 cmusing a 170-km sensor swath width in the presence of cloud attenuation effects. Further, the integrated hydrologic response, as represented by total (surface and subsurface) runoff estimates during the snow ablation season, are also enhanced when assimilating synthetic LiDAR snow depth retrievals with errors below this level.

Yonghwan Kwon↗
NASA NTRSDate not supplied

Advances in Plume-Surface Interaction Simulation Capability Under Lunar Landing Conditions

Plume-Surface Interaction (PSI) between lander engine plumes and native regolith soil presents primary hazards in obscuration and contamination by particle clouds, high-energy ejecta streams, and landing area cratering damage. The MSFC Fluid Dynamics Branch has assembled a portfolio of simulation tools to develop a predictive PSI capability for NASA customers such as the Human Lander System (HLS) and Commercial Lunar Payload Services (CLPS). These tools are matured via funding by NASA’s STMD Game Changing Development Program and the NASA SBIR/STTR Program.

Peter A Liever↗
NASA NTRS1984

The Shuttle Mission Simulator computer generated imagery

Equipment available in the primary training facility for the Space Transportation System (STS) flight crews includes the Fixed Base Simulator, the Motion Base Simulator, the Spacelab Simulator, and the Guidance and Navigation Simulator. The Shuttle Mission Simulator (SMS) consists of the Fixed Base Simulator and the Motion Base Simulator. The SMS utilizes four visual Computer Generated Image (CGI) systems. The Motion Base Simulator has a forward crew station with six-degrees of freedom motion simulation. Operation of the Spacelab Simulator is planned for the spring of 1983. The Guidance and Navigation Simulator went into operation in 1982. Aspects of orbital visual simulation are discussed, taking into account the earth scene, payload simulation, the generation and display of 1079 stars, the simulation of sun glare, and Reaction Control System jet firing plumes. Attention is also given to landing site visual simulation, and night launch and landing simulation.

Henderson, T. H.↗