Search NASA⌕ Search

SEARCH · Search NASA

Results for “liftoff”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

A numerical algorithm to propagate navigation error covariance matrices associated with generalized strapdown inertial measurement units

The design and operation of a Strapdown Navigation Analysis Program (SNAP) developed to perform covariance analysis on spacecraft inertial-measurement-unit (IMU) navigation errors are described and demonstrated. Consideration is given to the IMU modeling subroutine (with user-specified sensor characteristics), the data input procedures, state updates and the simulation of instrument failures, the determination of the nominal trajectory, the mapping-matrix and Monte Carlo covariance-matrix propagation methods, and aided-navigation simulation. Numerical results are presented in tables for sample applications involving (1) the Galileo/IUS spacecraft from its deployment from the Space Shuttle to a point 10 to the 8th ft from the center of the earth and (2) the TDRS-C/IUS spacecraft from Space Shuttle liftoff to a point about 2 h before IUS deployment. SNAP is shown to give reliable results for both cases, with good general agreement between the mapping-matrix and Monte Carlo predictions.

Weir, Kent A.↗
NASA NTRS1989

Evaluation of Composite Materials for Use on Launch Complexes

Commercially available composite structural shapes were evaluated for use. These composites, fiberglass-reinforced polyester and vinylester resin materials are being used extensively in the fabrication and construction of low maintenance, corrosion resistant structures. The evaluation found that in many applications these composite materials can be successfully used at the space center. These composite materials should not be used where they will be exposed to the hot exhaust plume/cloud of the launch vehicle during the liftoff, and caution should be taken in their use in areas where electrostatic discharge and hypergolic propellant compatibility are primary concerns.

Finchum, A.↗
NASA NTRS1990

RSRM-13 (360Q013) ballistics mass properties flight designation STS-41

The propulsion performance and reconstructed mass properties data from Thiokol's RSRM-13 motors which were assigned to the STS-41 launch are presented. The SRM propellant, TP-H1148, is a composite type solid propellant, formulated of polybutadiene acrylic acid acryonitrile terpolymer binder, epoxy curing agent, ammonium perchlorate oxidizer, and aluminum powder fuel. A small amount of burning rate catalyst (iron oxide) was added to achieve the desired propellant burn rate. The propellant evaluation and raw material information are also presented. The presented ballistic performance was based on the Operational Flight Instrumentation. The adjustments made to the raw data on this flight include biasing the data to correct ambient pressure before liftoff. The performance from each motor as well as matched pair performance values were well within the CEI Specification requirements.

Laubacher, Brian A.↗
NASA NTRS1991

A study of three dimensional turbulent boundary layer separation and vortex flow control using the reduced Navier Stokes equations

A reduced Navier Stokes (RNS) initial value space marching solution technique was applied to vortex generator and separated flow problems and demonstrated good predictions of the engine face flow field. This RNS solution technique using FLARE approximations can adequately describe the topological and topographical structure flow separation associated with vortex liftoff, and this conclusion led to the concept of a subclass of separations which can be called vorticity separations: separations dominated by the transport of vorticity. Adequate near wall resolution of vorticity separations appears necessary for good predictions of these flows.

Anderson, Bernhard H.↗
NASA NTRS1991

Launch vehicle performance using metallized propellants

Metallized propellant propulsion systems are considered as replacements for the solid rocket boosters and liquid sustainer stages on the current launch vehicles: both the Space Transportation System (STS) and the Titan 4. Liquid rocket boosters for the STS were analyzed as replacements for current solid rocket boosters. These boosters can provide a liquid propulsion system within the volume constraints of a solid rocket booster. A replacement for the Space Shuttle Main Engines using metallized O2/H2/Al was studied. The liquid stages of the Titan 4 were also investigated; the Aerozine-50 (A-50) fuel was replaced with metallized storable A-50/Al. A metallized propellant is similar to a traditional liquid propellant. However, it has metal particles, such as aluminum, that are suspended in a gelled fuel, such as hydrogen, RP-1, A-50 or monomethyl hydrazine (MMH). The fuels then undergo combustion with liquid oxygen or nitrogen tetroxide (NTO). These propellants provide options for increasing the performance of existing launch vehicle chemical propulsion systems by increasing fuel density or specific impulse or both. These increases in density and specific impulse can significantly reduce the propulsion system liftoff weight and allow a liquid rocket booster to fit into the same volume as an existing solid rocket booster. Also, because gelled fuels are akin to liquid propellants, metallized systems can provide enhanced controllability over solid propulsion systems. Gelling of the propellant also reduces the sensitivity to impacts and consequently reduces the propellant explosion hazard.

Palaszewski, Bryan A.↗
NASA NTRS1991

Brake lock mechanism for the two axis pointing system

Six months prior to shipment of the Broadband X-ray Telescope to the Kennedy Space Center for flight aboard the Space Shuttle Columbia, a major system failure occurred. During modal survey testing of the telescope's gimbal pointing system, the roll axis brake unexpectedly released. Low level vibration and static preloads present during the modal survey were within the expected flight environment. Brake release during shuttle liftoff or ascent was an unacceptable risk to mission success; thus, a Brake Lock Mechanism (BLM) was developed.

Posey, Alan↗
NASA NTRS1991

Astronauts give GRO a helping hand

The eighth mission of the Space Shuttle Atlantis, during which an emergency spacewalk was performed to help deploy the Gamma-Ray Observatory (GRO), is described and illustrated with extensive photographs. The countdown and liftoff are recalled, and a day-by-day history of the mission is provided. Particular attention is given to the Extravehicular Activity Development Flight Experiment, designed to obtain data for future spacewalks, and the Crew and Equipment Translation Aid, aimed at testing carts that spacewalking astronauts could use to move along the truss structure of the Space Station.

Schulling, Roelof L.↗
NASA NTRS1991

Launch vehicle performance using metallized propellants

Metallized propellant propulsion systems are considered as replacements for the solid rocket boosters and liquid sustainer stages on the current launch vehicles: both the Space Transportation System (STS) and the Titan 4. Liquid rocket boosters for the STS were analyzed as replacements for current solid rocket boosters. These boosters can provide a liquid propulsion system within the volume constraints of a solid rocket booster. A replacement for the Space Shuttle Main Engines using metallized 02/H2/A1 was studied. The liquid stages of the Titan 4 were also investigated; the Aerozine-50 (A-50) fuel was replaced with metallized storable A-50/A1. A metallized propellant is similar to a traditional liquid propellant. However, it has metal particles, such as aluminum, that are suspended in a gelled fuel, such as hydrogen, RP-1, A-50 or monomethyl hydrazine (MMH). The fuels then undergo combustion with liquid oxygen or nitrogen tetroxide (NTO). These propellants provide options for increasing the performance of existing launch vehicle chemical propulsion systems by increasing fuel density or specific impulse or both. These increases in density and specific impulse can significantly reduce the propulsion system liftoff weight and allow a liquid rocket booster to fit into the same volume as an existing solid rocket booster. Also, because gelled fuels are akin to liquid propellants, metallized systems can provide enhanced controllability over solid propulsion systems. Gelling of the propellant also reduces the sensitivity to impacts and consequently reduces the propellant explosion hazard.

Palaszewski, Bryan↗
NASA NTRS1991

AI aerospace components

An evaluation is made of the application of novel, AI-capabilities-related technologies to aerospace systems. Attention is given to expert-system shells for Space Shuttle Orbiter mission control, manpower and processing cost reductions at the NASA Kennedy Space Center's 'firing rooms' for liftoff monitoring, the automation of planetary exploration systems such as semiautonomous mobile robots, and AI for battlefield staff-related functions.

Heindel, Troy A.↗
NASA NTRS1991

Space shuttle Mission Control Center upgrade

The Mission Control Center (MCC) is the facility that provides centralization of all mission operations in support of the shuttle from liftoff through landing. This facility serves as the focal point for real time flight control operations supporting the shuttle, spacelab, and selected payload systems. MCC upgrade accomplishments are as follows: replaced 5 mainframe computers and the associated input/output data interfaces; developed and installed a distributed data system with 81 workstations, 5 LANs, data drivers, and a fiber optic distribution subsystem; developed over 1.5 million lines of code to support new distributed system; developed new digital voice system which provides the MCC capacity to handle th Shuttle programs demands and growth potential to handle Space Station; replaced failing digital TV equipment with digital generation equipment; replaced obsolete center screen projector; and provided the platform for the multiprogram control center.

Duffin, Pat↗
NASA NTRS1992

Li/BCX (thionyl chloride) battery for the NASA AN/PRC-112 survival radio

As part of the NASA contingency planning related to aborting a launch after liftoff, an emergency radio is required for use by the crew when they return to Earth at some unplanned location. The power source for the radio must be able to satisfy the performance requirements for the radio's mission as well as be compatible with in-cabin storage in the space shuttle. The radio needs a base load power of about 1 W with capability to handle power spikes greater then 6.5 W. A slightly enlarged battery pack using the Li/BCX chemistry in C-size cells was developed that meets these power levels and extends the operational life of the radio by over a factor of four compared to its operation using a Li/SO2 cell battery pack. In addition, the cells meet the requirements for the Li/BCX cells used for extra-vehicular activities by the crew of the shuttle. One of the major qualifying tests is the ability of the cells to withstand exposure to high temperature (149 C) without leaking. Electrical performance and thermal abuse test data will be presented for the cells.

Ebel, Steven J.↗
NASA NTRS1992

Coupled loads analysis for Space Shuttle payloads

Described here is a method for determining the transient response of, and the resultant loads in, a system exposed to predicted external forces. In this case, the system consists of four racks mounted on the inside of a space station resource node module (SSRNMO) which is mounted in the payload bay of the space shuttle. The predicted external forces are forcing functions which envelope worst case forces applied to the shuttle during liftoff and landing. This analysis, called a coupled loads analysis, is used to couple the payload and shuttle models together, determine the transient response of the system, and then recover payload loads, payload accelerations, and payload to shuttle interface forces.

Eldridge, J.↗
NASA NTRS1992

Lewis icing research tunnel test of the aerodynamic effects of aircraft ground deicing/anti-icing fluids

A wind tunnel investigation of the effect of aircraft ground deicing/anti-icing fluids on the aerodynamic characteristics of a Boeing 737-200ADV airplane was conducted. The test was carried out in the NASA Lewis Icing Research Tunnel. Fluids tested include a Newtonian deicing fluid, three non-Newtonian anti-icing fluids commercially available during or before 1988, and eight new experimental non-Newtonian fluids developed by four fluid manufacturers. The results show that fluids remain on the wind after liftoff and cause a measurable lift loss and drag increase. These effects are dependent on the high-lift configuration and on the temperature. For a configuration with a high-lift leading-edge device, the fluid effect is largest at the maximum lift condition. The fluid aerodynamic effects are related to the magnitude of the fluid surface roughness, particularly in the first 30 percent chord. The experimental fluids show a significant reduction in aerodynamic effects.

Runyan, L. James↗
NASA NTRS1992

Design Feasibility Study of a Space Station Freedom Truss

Here, the focus is on the design and configuration feasibility of the short spacer for the Space Station Program in its launch configuration. The product of this study is being used by Rockwell International (Rocketdyne Division) as they continue their design concept of the current short spacer configuration. It is anticipated that the launch loads will dominate the on-orbit loads and dictate the design configuration of the short spacer. At the present time, the on-orbit loads have not been generated. The structural analysis discussed herein is based on the transient events derived from the Space Transportation System (STS) Interface Control Document (ICD). The transient loading events consist of liftoff loads, landing loads, and emergency landing loads. The quasi-static loading events have been neglected, since the magnitude of the acceleration factors are lower than the transient acceleration factors. The normal mode analyses presented herein are based on the most feasible configurations with acceptable stress ranges.

Armand, Sasan C.↗
NASA NTRS1990

Nonlinear shell analysis of the Space Shuttle Solid Rocket Boosters

A variety of structural analyses have been performed on the Solid Rocket Boosters (SRB's) to provide information that would contribute to the understanding of the failure which destroyed the Space Shuttle Challenger. This paper describes nonlinear shell analyses that were performed to characterize the behavior of an overall SRB structure and a segment of the SRB in the vicinity of the External Tank Attachment (ETA) ring. Shell finite element models were used that would accurately reflect the global load transfer in an SRB in a manner such that nonlinear shell collapse and ovalization could be assessed. The purpose of these analyses was to calculate the overall deflection and stress distributions for these SRB models when subjected to mechanical loads corresponding to critical times during the launch sequence. Static analyses of these SRB models were performed using a 'snapshot picture' of the loads. Analytical results obtained using these models show no evidence of nonlinear shell collapse for the pre-liftoff loading cases considered.

Knight, N. F., Jr.↗
NASA NTRS1991

A study of three dimensional turbulent boundary layer separation and vortex flow control using the reduced Navier Stokes equations

A reduced Navier-Stokes (RNS) initial value space marching solution technique was applied to vortex generator and separated flow problems and demonstrated good predictions of the engine face flow field. This RNS solution technique using FLARE approximations can adequately describe the topological and topographical structure flow separation associated with vortex liftoff, and this conclusion led to the concept of a subclass of separations which can be called vorticity separations: separations dominated by the transport of vorticity. Adequate near wall resolution of vorticity separations appears necessary for good predictions of these flows.

Anderson, Bernhard H.↗
NASA NTRS1992

Advanced propulsion for LEO-Moon transport. 2: Tether configurations in the LEO-Moon system

This brief work discusses a possible application of a tether as a dynamical element in a low Earth orbit (LEO)-Moon transport system, and is a part of the Cal Space study of that transport system. To be specific, that study concentrated on the downward transport of O2 from the Moon to LEO, where it is stored for use as a rocket propellant, thus reducing Earth liftoff mass requirements by a factor of about 8. Moreover, in order to display clearly the role of advanced technology, only one novel technology was introduced at a single node in the transport system, the rest being 'conventional' rocket transport. Tethers were found useful in several different roles: hanging from platforms in lunar orbits, as supports for elevators, spinning in LEO, or spinning in a tether transport orbit, an elliptical orbit with perigee at approximately 600 km. This last use is considered here. Presented are the usefulness of the tether, nature of the tether system, the apparatus needed to support, deploy, and control it, and a discussion of needed developments.

Arnold, J. R.↗
NASA NTRS1991

The lightcraft project

Rensselaer Polytechnic Institute has been developing a transatmospheric 'Lightcraft' technology which uses beamed laser energy to propel advanced shuttle craft to orbit. In the past several years, Rensselaer students have analyzed the unique combined-cycle Lightcraft engine, designed a small unmanned Lightcraft Technology Demonstrator, and conceptualized larger manned Lightcraft - to name just a few of the interrelated design projects. The 1990-91 class carried out preliminary and detailed design efforts for a one-person 'Mercury' Lightcraft, using computer-aided design and finite-element structural modeling techniques. In addition, they began construction of a 2.6 m-diameter, full-scale engineering prototype mockup. The mockup will be equipped with three robotic legs that 'kneel' for passenger entry and exit. More importantly, the articulated tripod gear is crucial for accurately pointing at, and tracking the laser relay mirrors, a maneuver that must be performed just prior to liftoff. Also accomplished were further design improvements on a 6-inch-diameter Lightcraft model (for testing in RPI's hypersonic tunnel), and new laser propulsion experiments. The resultant experimental data will be used to calibrate Computational Fluid Dynamic (CFD) codes and analytical laser propulsion models that can simulate vehicle/engine flight conditions along a transatmospheric boost trajectory. These efforts will enable the prediction of distributed aerodynamic and thruster loads over the entire full-scale spacecraft.

Messitt, Don G.↗