SEARCH · Search NASA

Results for “mode shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Sensitivity of Space Station Alpha Joint robust controller to structural modal parameter variations

The baseline design of the photovoltaic-array sun-tracking control system is presented with special attention given to the optimization of design variables related to stability and performance. The procedures utilized to attenuate control/structure interaction are described, and controller sensitivity to variations in structural modal parameters is examined. Constrained optimization techniques determine the stability margin and tracking capability, which are then tested for sensitivity to variations in natural frequency, mode-shape amplitudes, and modal-damping ratios. The effect of variations in the modal parameters of the dominant modes on performance indicators is also examined to optimize tracking-performance responsiveness and satisfy the design requirements. It is concluded that accurate on-orbit modal data are necessary to make the reoptimization procedure effective in improving the performance of the control system.

Kumar, Renjith R.↗

NASA NTRS1981

Transonic flutter study of a wind-tunnel model of an arrow-wing supersonic transport

A 1/20-size, low-speed flutter model of the SCAT-15F complete airplane was tested on cables to simulate a near free-flying condition. Only the model wing and fuselage were flexible. Flutter boundaries were measured for a nominal configuration and a configuration with wing fins removed at Mach numbers M from 0.76 to 1.2. For both configurations, the transonic dip in the wing flutter dynamic pressure q boundary was relatively small and the minimum flutter q occurred near M = 0.92. Removing the wing fins increased the flutter q about 14 percent and changed the flutter mode from symmetric to antisymmetric. Vibration and flutter analyses were made using a finite-element structural representation and subsonic kernel-function aerodynamics. For the nominal configuration, the analysis (using calculated modal data) predicted the experimental flutter q levels within 10 percent but did not predict the correct flutter mode at the higher M. For the configuration without wing fins, the analysis predicted 16 to 36 percent unconservative (higher than experimental) flutter q levels and showed extreme sensitivity to mass representation details that affected wing tip mode shapes. For high subsonic M, empennage aerodynamics had a significant effect on the predicted flutter boundaries of several symmetric modes.

Ruhlin, C. L.↗

NASA NTRS1991

Acoustical analysis of gear housing vibration

The modal and acoustical analysis of the NASA gear-noise rig is described. Experimental modal analysis techniques were used to determine the modes of vibration of the transmission housing. The resulting modal data were then used in a boundary element method (BEM) analysis to calculate the sound pressure and sound intensity on the surface of the housing as well as the radiation efficiency of each mode. The radiation efficiencies of the transmission housing modes are compared with theoretical results for finite, baffled plates. A method that uses the measured mode shapes and the BEM to predict the effect of simple structural changes on the sound radiation efficiency of the modes of vibration is also described.

Seybert, A. F.↗

NASA NTRS1991

Acoustical analysis of gear housing vibration

Seybert, A. F.↗

NASA NTRS1984

Galileo spacecraft modal test and evaluation of testing techniques

The structural configuration, modal test requirements and pre-test activities involved in modeling the expected dynamic environment and responses of the Galileo spacecraft are discussed. The probe will be Shuttle-launched in 1986 and will gather data on the Jupiter system. Loads analysis for the 5300 lb spacecraft were performed with the NASTRAN code, and covered 10,000 static degrees of freedom and 1600 mass degrees of freedom. A modal analysis will be used to verify the predictions for natural frequencies, mode shapes, orthogonality checks, residual mass, modal damping and forces, and generalized forces. Verification of the validity of considering only 70 natural modes in the numerical simulation is being performed by examining the forcing functions of the analysis. The analysis led to requirements that 162 channels of accelerometer data and 118 channels of strain gage data be recorded during shaker tests to reveal areas where design changes will be needed to eliminate vibration peaks.

Chen, J.-C.↗

NASA NTRS1973

Results of ground vibration tests on a YF-12 airplane

Ground vibration tests were conducted on a YF-12 airplane. To approximate a structural free-free boundary condition during the tests, each of the landing gears was supported on a support system designed to have a low natural frequency. The test equipment and the procedures used for the ground vibration tests are described. The results are presented in the form of frequency response data, measured mode lines, and elastic mode shapes for the wing/body, rudder, and fuselage ventral fin. In the frequency range between 3.4 cps and 28.8 cps, nine symmetrical wing/body modes, six antisymmetrical wing/body modes, two rudder modes, and one ventral fin mode were measured.

Wilson, R. J.↗

NASA NTRS1980

Vibration analysis of the Long Duration Exposure Facility (LDEF) using SPAR

The structural modeling of the Long Duration Exposure Facility (LDEF) utilizing the SPAR system of computer programs for vibration analysis is discussed. The technical areas of interest were: (1) development of the LDEF finite element model; (2) derivation of tray effective panel stiffness matrix using finite element tray models; (3) assessment of attachment conditions and end fitting flexibility by comparing SPAR with test static displacements; (4) SPAR grouping; and (5) derivation of the LDEF frequencies and mode shapes and comparing them with tests. Special detailed finite element modeling was required to obtain good agreement between analytical and test vibration modes. An orthotropic panel in the overall model was developed. Orthotropic stiffness for this panel were obtained from finely detailed statically loaded SPAR models which included stiffness and allowed for partial relative sliding of the tray clamping attachments. Sensitivity to LDEF joint boundary conditions was determined, and static test data proved valuable in assessing modeling of local end fittings.

Edighoffer, H.↗

NASA NTRS1982

Comparison of beam and shell theories for the vibrations of thin turbomachinery blades

Vibration analysis of turbomachinery blades has traditionally been carried out by means of beam theory. In recent years two-dimensional methods of blade vibration analysis have been developed, most of which utilize finite elements and tend to require considerable computation time. More recently a two-dimensional method of blade analysis has evolved which does not require finite elements and is based upon shell equations. The present investigation has the primary objective to demonstrate the accuracy and limitations of blade vibration analyses which utilize one-dimensional, beam theories. It is found that beam theory is generally inadequate to determine the free vibration frequencies and mode shapes of moderate to low aspect ratio turbomachinery blades. The shallow shell theory, by contrast, is capable of representing all the vibration modes accurately. However, the one-dimensional beam theory has an important advantage over the two-dimensional shell theory for blades and vibration modes. It uses fewer degrees of freedom, thus requiring less computer time.

Leissa, A. W.↗

NASA NTRS1984

Propagation and radiation of sound from flanged circular ducts with circumferentially varying wall admittances. I Semi-infinite ducts. II - Finite ducts with sources

Sound propagation in infinite, semiinfinite, and finite circular ducts with circumferentially varying wall admittances is investigated analytically. The infinite case is considered, and an example demonstrates the effects of wall-admittance distribution on dispersion characteristics and mode shapes. An exact solution is obtained for the semiinfinite case, a circular duct with a flanged opening: sidelobe suppression and circumferential-mode energy scattering leading to radiated-field asymmetry are found. A finite duct system with specified hard-walled pressure sources is examined in detail, evaluating reflection coefficients, transmission losses, and radiated-field directivity. Graphs and diagrams are provided, and the implications of the results obtained for the design of aircraft-turbofan inlet liners are discussed.

Fuller, C. R.↗

NASA NTRS1992

Application of an enhanced Coordinate Modal Assurance Criterion

This paper presents an extension of the Coordinate Modal Assurance Criterion (COMAC) for spatial comparison of mode shapes. As is the case for the original COMAC, this enhanced COMAC helps identify degrees of freedom differences between test and analysis modes, but also overcomes some of the limitations of the original COMAC. The original COMAC cannot identify errors caused by scaling or polarity mistakes in the test data. Such mistakes are easily made during modal tests and not always easily detected since they do not affect the subjective quality of a frequency response function.

Hunt, David L.↗

NASA NTRS1998

Buckling mode localization in elastic plates due to misplacement in the stiffener location

This paper deals with the buckling of the stiffened plate under uni-axial compression. The direct integration of the governing differential equation is performed and the exact solution to the problem is obtained. As examples, a square plate with single stiffener, and a stiffened three-span, continuous plate are investigated, with special attention given to the influence of stiffener misplacement on the buckling load and mode shape of the plate. It is found that a small misplacement of the stiffeners from the nominal configuration may change the buckling mode from a global one to a highly localized one.

Elishakoff, I.↗

NASA NTRS1981

Vibrations of twisted rotating blades

The literature dealing with vibrations of turbomachinery blades is voluminous, but the vast majority of it treats the blades as beams. In a previous paper a two-dimensional analytical procedure was developed and demonstrated on simple models of blades having camber. The procedure utilizes shallow shell theory along with the classical Ritz method for solving the vibration problem. Displacement functions are taken as algebraic polynomials. In the present paper the method is demonstrated on blade models having camber. Comparisons are first made with results in the literature for nonrotating twisted plates and various disagreements between results are pointed out. A method for depicting mode shape information is demonstrated, permitting one to examine all three components of displacement. Finally, the analytical procedure is demonstrated on rotating twisted blade modes, both without and with camber.

Leissa, A. W.↗

NASA NTRS1967

Vibration modes of an orbiting radio telescope

Vibration mode shape and frequencies of orbiting radio telescope

ORBITING SATELLITE↗

NASA NTRS1993

Improvements to a method for the geometrically nonlinear analysis of compressively loaded stiffened composite panels

The NLPAN computer code uses a finite-strip approach to the analysis of thin-walled prismatic composite structures such as stiffened panels. The code can model in-plane axial loading, transverse pressure loading, and constant through-the-thickness thermal loading, and can account for shape imperfections. The NLPAN code represents an attempt to extend the buckling analysis of the VIPASA computer code into the geometrically nonlinear regime. Buckling mode shapes generated using VIPASA are used in NLPAN as global functions for representing displacements in the nonlinear regime. While the NLPAN analysis is approximate in nature, it is computationally economical in comparison with finite-element analysis, and is thus suitable for use in preliminary design and design optimization. A comprehensive description of the theoretical approach of NLPAN is provided. A discussion of some operational considerations for the NLPAN code is included. NLPAN is applied to several test problems in order to demonstrate new program capabilities, and to assess the accuracy of the code in modeling various types of loading and response. User instructions for the NLPAN computer program are provided, including a detailed description of the input requirements and example input files for two stiffened-panel configurations.

Stoll, Frederick↗

NASA NTRS1998

Potential and Limitations of the Modal Characterization of a Spacecraft Bus Structure by Means of Active Structure Elements

Theoretical and experimental studies have been performed to investigate the potential and limitations of the modal characterization of a typical spacecraft bus structure by means of active structure elements. The aim of these studies has been test and advance tools for performing an accurate on-orbit modal identification which may be characterized by the availability of a generally very limited test instrumentation, autonomous excitation capabilities by active structure elements and a zero-g environment. The NASA LARC CSI Evolutionary Testbed provided an excellent object for the experimental part of this study program. The main subjects of investigation were: (1) the selection of optimum excitation and measurement to unambiguously identify modes of interest; (2) the applicability of different types of excitation means with focus on active structure elements; and (3) the assessment of the modal identification potential of different types of excitation functions and modal analysis tools. Conventional as well as dedicated modal analysis tools were applied to determine modal parameters and mode shapes. The results will be presented and discussed based on orthogonality checks as well as on suitable indicators for the quality of the acquired modes with respect to modal purity. In particular, the suitability for modal analysis of the acquired frequency response functions as obtained by excitation with active structure elements will be demonstrated with the help of reciprocity checks. Finally, the results will be summarized in a procedure to perform an on-orbit modal identification, including an indication of limitation to be observed.

Grillenbeck, Anton M.↗

NASA NTRS1990

Dynamics of Multistage Gear Transmission with Effects of Gearbox Vibrations

A comprehensive approach is presented in analyzing the dynamic behavior of multistage gear transmission systems with the effects of gearbox induced vibrations and mass imbalances of the rotor. The modal method, with undamped frequencies and planar mode shapes, is used to reduce the degrees of freedom of the gear system for time-transient dynamic analysis. Both the lateral and torsional vibration modes of each rotor-bearing-gear stage as well as the interstage vibrational characteristics are coupled together through localized gear mesh tooth interactions. In addition, gearbox vibrations are also coupled to the rotor-bearing-gear system dynamics through bearing support forces between the rotor and the gearbox. Transient and steady state dynamics of lateral and torsional vibrations of the geared system are examined in both time and frequency domains to develop interpretations of the overall modal dynamic characteristics under various operating conditions. A typical three-stage geared system is used as an example. Effects of mass imbalance and gearbox vibrations on the system dynamic behavior are presented in terms of modal excitation functions for both lateral and torsional vibrations. Operational characteristics and conclusions are drawn from the results presented.

Choy, F. K.↗

NASA NTRS1987

An evaluation of higher-order modal methods for calculating transient structural response

The present study evaluates a higher-order modal method proposed by Leung for transient structural analysis entitled the force-derivative method. This method repeatedly integrates by parts with respect to time the convolution-integral form of the structural response to produce successively better approximations to the contribution of the higher modes which are neglected in the modal summation. Comparisons are made of the force-derivative, the mode-displacement, and the mode-acceleration methods for several numerical example problems for various times, levels of damping, and forcing functions. The example problems include a tip-loaded cantilevered beam and a simply-supported multispan beam. The force-derivative method is shown to converge to an accurate solution in fewer modes than either the mode-displacement or the mode-acceleration methods. In addition, for problems in which there are a large number of closely-spaced frequencies whose mode shapes have a negligible contribution to the response, the force derivative method is very effective in representing the effect of the important, but otherwise neglected, higher modes.

Camarda, Charles J.↗

NASA NTRS2006

Dynamic Analysis of Large In-Space Deployable Membrane Antennas

This paper presents a vibration analysis of an eight-meter diameter membrane reflectarray antenna, which is composed of a thin membrane and a deployable frame. This analysis process has two main steps. In the first step, a two-variable-parameter (2-VP) membrane model is developed to determine the in-plane stress distribution of the membrane due to pre-tensioning, which eventually yields the differential stiffness of the membrane. In the second step, the obtained differential stiffness is incorporated in a dynamic equation governing the transverse vibration of the membrane-frame assembly. This dynamic equation is then solved by a semi-analytical method, called the Distributed Transfer Function Method (DTFM), which produces the natural frequencies and mode shapes of the antenna. The combination of the 2-VP model and the DTFM provides an accurate prediction of the in-plane stress distribution and modes of vibration for the antenna.

vibrations↗