Search NASA⌕ Search

SEARCH · Search NASA

Results for “model driven design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Design considerations for flight test of a fault inferring nonlinear detection system algorithm for avionics sensors

The modifications to the design of a fault inferring nonlinear detection system (FINDS) algorithm to accommodate flight computer constraints and the resulting impact on the algorithm performance are summarized. An overview of the flight data-driven FINDS algorithm is presented. This is followed by a brief analysis of the effects of modifications to the algorithm on program size and execution speed. Significant improvements in estimation performance for the aircraft states and normal operating sensor biases, which have resulted from improved noise design parameters and a new steady-state wind model, are documented. The aircraft state and sensor bias estimation performances of the algorithm's extended Kalman filter are presented as a function of update frequency of the piecewise constant filter gains. The results of a new detection system strategy and failure detection performance, as a function of gain update frequency, are also presented.

Caglayan, A. K.↗
NASA NTRS1986

Design considerations for flight test of a fault inferring nonlinear detection system algorithm for avionics sensors

This paper summarizes the modifications made to the design of a fault inferring nonlinear detection system (FINDS) algorithm to accommodate flight computer constraints and the resulting impact on the algorithm performance. An overview of the flight data-driven FINDS algorithm is presented. This is followed by a brief analysis of the effects of modifications to the algorithm on program size and execution speed. Significant improvements in estimation performance for the aircraft states and normal operating sensor biases, which have resulted from improved noise design parameters and a new steady-state wind model, are documented. The aircraft state and sensor bias estimation performances of the algorithm's extended Kalman filter are presented as a function of update frequency of the piecewise constant filter gains. The results of a new detection system strategy and failure detection performance, as a function of an update frequency, are also presented.

Caglayan, A. K.↗
NASA NTRS2004

Performance of a Fuel-Cell-Powered, Small Electric Airplane Assessed

Rapidly emerging fuel-cell-power technologies may be used to launch a new revolution of electric propulsion systems for light aircraft. Future small electric airplanes using fuel cell technologies hold the promise of high reliability, low maintenance, low noise, and - with the exception of water vapor - zero emissions. An analytical feasibility and performance assessment was conducted by NASA Glenn Research Center's Airbreathing Systems Analysis Office of a fuel-cell-powered, propeller-driven, small electric airplane based on a model of the MCR-01 two-place kitplane (Dyn'Aero, Darois, France). This assessment was conducted in parallel with an ongoing effort by the Advanced Technology Products Corporation and the Foundation for Advancing Science and Technology Education. Their project - partially funded by a NASA grant - is to design, build, and fly the first manned, continuously propelled, nongliding electric airplane. In our study, an analytical performance model of a proton exchange membrane (PEM) fuel cell propulsion system was developed and applied to a notional, two-place light airplane modeled after the MCR-01 kitplane. The PEM fuel cell stack was fed pure hydrogen fuel and humidified ambient air via a small automotive centrifugal supercharger. The fuel cell performance models were based on chemical reaction analyses calibrated with published data from the fledgling U.S. automotive fuel cell industry. Electric propeller motors, rated at two shaft power levels in separate assessments, were used to directly drive a two-bladed, variable-pitch propeller. Fuel sources considered were compressed hydrogen gas and cryogenic liquid hydrogen. Both of these fuel sources provided pure, contaminant-free hydrogen for the PEM cells.

Berton, Jeffrey J.↗
NASA NTRS2021

In-Flight Turbulence Emulation for Fixed-Wing Aircraft using Equivalent Multisine Excitations

A procedure is discussed for designing control-equivalent turbulence input (CETI) excitations to emulate a fixed-wing aircraft response to turbulence while flying through calm air. These excitations are added to the actuator commands to produce the same motion of the aircraft that would have resulted from flying in actual turbulence. Although CETI models are usually shaping filters driven by white noise inputs, the equivalent control inputs in this report were constructed as multisine excitations, which enables mimicking the response to turbulence with arbitrary power spectra, within hardware limitations. Practical aspects of the approach are discussed, such as actuator dynamics, model uncertainty, actual in-flight turbulence, and others. The procedure is demonstrated using a flight dynamics simulation model of a subscale generic jet transport aircraft.

control-equivalent turbulence inputs (CETI)↗
NASA NTRS2021

Secondary Science Teachers’ Implementation of a Curricular Intervention When Teaching With Global Climate Models

In the past decade, emphasis on promoting “climate literacy” in K-16 science classrooms has increased. Teachers play a critical role in cultivating these opportunities, especially in secondary science classrooms. However, most prior climate education research has focused on students and student learning; little is known about how teachers implement climate-focused curricular interventions. Here, we report findings from a concurrent mixed methods, multiple-case study of four secondary science teachers’ implementation of a new, NGSS-aligned, model-centric climate curriculum module grounded in the use of a data-driven, computer-based climate modeling tool—Easy Global Climate Model (EzGCM). We employ multiple data sources, including video-recorded classroom observations, interviews, and instructional artifacts, and both qualitative and quantitative analyses, to investigate how teachers implemented the curriculum. Findings show that, overall, teachers implemented the curriculum in ways that were less model-centric than designed, placing greater emphasis on EzGCM itself rather than using the model to investigate Earth’s changing climate. Additionally, we present detailed single-case studies of each participant teacher that highlight differences in teachers’ implementation of the curriculum module and their reasoning for making observed instructional decisions. This research sheds light on the design of secondary science learning environments by illustrating the varied ways teachers implement a climate-focused curriculum to support students’ developing climate literacy. This has important implications for the design of climate-focused curriculum and supports for teachers.

Secondary science teaching↗
NASA NTRSDate not supplied

Modeling the Effective Elasticity of Anisotropic Porous Materials

The development and optimization of composite materials designed for thermal protection of NASA’s spacecraft require understanding their physical response to high-enthalpy environments. To predict their macro-scale properties and behavior, high-fidelity 3D simulations are performed at the microscale on realistic representations of these composites. The digital microstructures are generated either synthetically or through X-ray micro-computed tomography reconstructions. One of the main challenges in the prediction of the structural response of heatshield materials is the computation of the effective elasticity of the fibrous composite, as well as the understanding of the deformation and stresses generated at the microscale. These are driven by the fiber layout within the microstructure and the distribution of the infused matrix. In this effort, the micro-mechanical linear elastic behavior of fibrous ablators is modeled using a numerical method based on the Multi-Point Stress Approximation (MPSA) finite volume scheme, a generalization of the more commonly used Multi-Point Flux Approximation (MPFA) that was presented at the 10th Ablation Workshop. To predict the behavior of fibrous and woven architectures, algorithms that compute the local fiber orientation are used. The implementation of the MPSA was verified using analytical solutions, engineering test cases, and compared against legacy Finite Element Analysis (FEA) software. The stress analysis models were then applied to real geometries used by NASA in thermal protection systems such as fibrous preforms and woven materials and the results were compared to experimental data.

Elasticity↗
NASA NTRS1992

Experimental studies of characteristic combustion-driven flows for CFD validation

A series of rocket-related studies intended to develop a suitable data base for validation of Computational Fluid Dynamics (CFD) models of characteristic combustion-driven flows was undertaken at the Propulsion Engineering Research Center at Penn State. Included are studies of coaxial and impinging jet injectors as well as chamber wall heat transfer effects. The objective of these studies is to provide fundamental understanding and benchmark quality data for phenomena important to rocket combustion under well-characterized conditions. Diagnostic techniques utilized in these studies emphasize determinations of velocity, temperature, spray and droplet characteristics, and combustion zone distribution. Since laser diagnostic approaches are favored, the development of an optically accessible rocket chamber has been a high priority in the initial phase of the project. During the design phase for this chamber, the advice and input of the CFD modeling community were actively sought through presentations and written surveys. Based on this procedure, a suitable uni-element rocket chamber was fabricated and is presently under preliminary testing. Results of these tests, as well as the survey findings leading to the chamber design, were presented.

Santoro, R. J.↗
NASA NTRS1975

Summary of model VTOL lift fan tests conducted at NASA Lewis Research Center

The purpose of the tests was to obtain overall performance and influencing factors as well as detailed measurements of the internal flow characteristics. The first experiment consisted of crossflow tests of a 15-inch diameter fan installed in a two-dimensional wing. Tests were run with and without exit louvers over a range of tunnel speeds, fan speeds, and wing angle of attack. The wing was used for a study of installation effects on lift fan performance. The model tested consisted of three 5.5-inch diameter tip-turbine driven model VTOL lift fans mounted chord-wise in the two-dimensional wing to simulate a pod-type array. Several inlet and exit cover door configurations and an adjacent fuselage panel were tested. For the third program, a pod was attached to the wing, and an investigation was conducted of the effect of design tip speed on the aerodynamic performance and noise of a 15-inch diameter lift fan-in-pod under static and crossflow conditions. Three single VTOL lift fan stages were designed for the same overall total pressure ratio but at three different rotor tip speeds.

Diedrich, J. H.↗
NASA NTRS1975

Automated parking garage system model

A one-twenty-fifth scale model of the key components of an automated parking garage system is described. The design of the model required transferring a vehicle from an entry level, vertically (+Z, -Z), to a storage location at any one of four storage positions (+X, -X, +Y, +Y, -Y) on the storage levels. There are three primary subsystems: (1) a screw jack to provide the vertical motion of the elevator, (2) a cam-driven track-switching device to provide X to Y motion, and (3) a transfer cart to provide horizontal travel and a small amount to vertical motion for transfer to the storage location. Motive power is provided by dc permanent magnet gear motors, one each for the elevator and track switching device and two for the transfer cart drive system (one driving the cart horizontally and the other providing the vertical transfer). The control system, through the use of a microprocessor, provides complete automation through a feedback system which utilizes sensing devices.

Collins, E. R., Jr.↗
NASA NTRS1976

Test data report: Low speed wind tunnel tests of a full scale, fixed geometry inlet, with engine, at high angles of attack

A full scale inlet test was to be done in the NASA-ARC 40' X 80' WT to demonstrate satisfactory inlet performance at high angles of attack. The inlet was designed to match a Hamilton-Standard 55 inch, variable pitch fan, driven by a Lycoming T55-L-11A gas generator. The test was installed in the wind tunnel on two separate occasions, but mechanical failures in the fan drive gear box early in each period terminated testing. A detailed description is included of the Model, installation, instrumentation and data reduction procedures.

Shain, W. M.↗
NASA NTRS1993

A minimum cost tolerance allocation method for rocket engines and robust rocket engine design

Rocket engine design follows three phases: systems design, parameter design, and tolerance design. Systems design and parameter design are most effectively conducted in a concurrent engineering (CE) environment that utilize methods such as Quality Function Deployment and Taguchi methods. However, tolerance allocation remains an art driven by experience, handbooks, and rules of thumb. It was desirable to develop and optimization approach to tolerancing. The case study engine was the STME gas generator cycle. The design of the major components had been completed and the functional relationship between the component tolerances and system performance had been computed using the Generic Power Balance model. The system performance nominals (thrust, MR, and Isp) and tolerances were already specified, as were an initial set of component tolerances. However, the question was whether there existed an optimal combination of tolerances that would result in the minimum cost without any degradation in system performance.

Gerth, Richard J.↗
NASA NTRS2000

A Reduced Order Model of the Linearized Incompressible Navier-Strokes Equations for the Sensor/Actuator Placement Problem

A reduced order modeling approach of the Navier-Stokes equations is presented for the design of a distributed optimal feedback kernel. This approach is based oil a Krylov subspace method where significant modes of the flow are captured in the model This model is then used in all optimal feedback control design where sensing and actuation is performed oil tile entire flow field. This control design approach yields all optimal feedback kernel which provides insight into the placement of sensors and actuators in the flow field. As all evaluation of this approach, a two-dimensional shear layer and driven cavity flow are investigated.

Allan, Brian G.↗
NASA NTRS2013

Acoustic Performance of Drive Rig Mufflers for Model Scale Engine Testing

Aircraft engine component testing at the NASA Glenn Research Center (GRC) includes acoustic testing of scale model fans and propellers in the 9- by15-Foot Low Speed Wind Tunnel (LSWT). This testing utilizes air driven turbines to deliver power to the article being studied. These air turbines exhaust directly downstream of the model in the wind tunnel test section and have been found to produce significant unwanted noise that reduces the quality of the acoustic measurements of the engine model being tested. This report describes an acoustic test of a muffler designed to mitigate the extraneous turbine noise. The muffler was found to provide acoustic attenuation of at least 8 dB between 700 Hz and 20 kHz which significantly improves the quality of acoustic measurements in the facility.

Stephens, David, B.↗
NASA NTRSDate not supplied

Integrated Handling Qualities Safety Analysis For Conceptual Design of Urban Air Mobility Vehicles

The recent emergence of distributed electric propulsion Vertical Takeoff and Landing (VTOL) aircraft has created a rapid introduction of new design concepts with unique stability and control characteristics. A challenge to realizing the full potential of these vehicles for urban transportation is to gain public acceptance which is largely driven by flight safety. This paper describes ongoing research to address the feasibility of integrating flying qualities safety metrics into conceptual design of VTOL Urban Air Mobility (UAM) vehicles. The discussion is composed of the approach and progress toward a toolbox that integrates with existing NASA rotorcraft design software and processes. Several key challenges are highlighted including modeling requirements for failures, identification of critical failures, and capturing critical failures, with robustness to model uncertainty. A discussion of requirements for safety metrics, specific to UAM vehicles, as well as the effects of the control system design is also included. Results to date have demonstrated the degradation in flying qualities metrics due to propulsion failures.

George Altamirano↗
NASA NTRS2009

Transient Modeling and Analysis of a Metabolic Heat-Regenerated Temperature Swing Adsorption (MTSA) System for a PLSS

A Metabolic heat-regenerated Temperature Swing Adsorption (MTSA) system is being developed for carbon dioxide, water and thermal control in a lunar and martian portable life support system (PLSS). A previous system analysis was performed to evaluate the impact of MTSA on PLSS design. That effort was Mars specific and assumed liquid carbon dioxide (LCO2) coolant made from martian resources. Transient effects were not considered but rather average conditions were used throughout the analysis. This effort takes into further consideration the transient effects inherent in the cycling MTSA system as well as assesses the use of water as coolant. Standard heat transfer, thermodynamic, and heat exchanger methods are presented to conduct the analysis. Assumptions and model verification are discussed. The tool was used to perform various system studies. Coolant selection was explored and takes into account different operational scenarios as the minimum bed temperature is driven by the sublimation temperature of the coolant (water being significantly higher than LCO2). From this, coolant mass is sized coupled with sorbent bed mass because MTSA adsorption performance decreases with increasing sublimation temperature. Reduction in heat exchanger performance and even removal of certain heat exchangers, like a recuperative one between the two sorbent beds, is also investigated. Finally, the coolant flow rate is varied over the cycle to determine if there is a more optimal means of cooling the bed from a mass perspective. Results of these studies and subsequent recommendations for system design are presented.

Iacomini, Christie↗
NASA NTRS2017

A Requirements-Driven Optimization Method for Acoustic Treatment Design

Acoustic treatment designers are able to attenuate specific noise sources inside turbofan engines. Subject to practical considerations, liner design variables may be manipulated to achieve a target attenuation spectrum. But, characteristics of the ideal attenuation spectrum can be difficult to know. Many multidisciplinary system effects govern how engine noise sources contribute to community noise. Given a hardwall fan noise source to be suppressed, and using an analytical certification noise model to compute a community noise measure of merit, the optimal attenuation spectrum can be derived using multidisciplinary systems analysis methods. The subject of this paper is an analytic method that derives the ideal target attenuation spectrum that minimizes noise perceived by observers on the ground. Software is developed and used to test and validate the method on a simple, notional source. With experience gained from minimizing noise of the simple source, the software is tested against a realistic hardwall fan source.

aircraft noise↗
NASA NTRS1986

Laser docking system flight experiment

Experiments necessary in the development of the Laser Docking System (LDS) are described. The LDS would be mounted in the Orbiter payload bay, along with a grid connected by fiber optic link to a computer in the cabin. The tests would be performed to aid in the design of an operational sensor which could track a passive target accurately enough to permit soft docking. Additional data would be gained regarding the LDS performance in space, the effects of Orbiter RCS plume impingement on the target, and refinements needed for the flight hardware. A working model which includes an IR laser steered by galvanometer-driven motors for bouncing beams off retroreflectors mounted on targets is described, together with a 300 ft long indoor test facility. Tests on Orbiter flights would first be in a wholly automatic mode and then in a man-in-the-loop mode.

Erwin, Harry O.↗
NASA NTRS1997

Flight Control System Design with Rate Saturating Actuators

Actuator rate saturation is an important factor adversely affecting the stability and performance of aircraft flight control systems. It has been identified as a catalyst in pilot-induced oscillations, some of which have been catastrophic. A simple design technique is described that utilizes software rate limiters to improve the performance of control systems operating in the presence of actuator rate saturation. As described, the technique requires control effectors to be ganged such that any effector is driven by only a single compensated error signal. Using an analysis of the steady-state behavior of the system, requirements are placed upon the type of the loop transmissions and compensators in the proposed technique. Application of the technique to the design of a multi-input/multi-output, lateral-directional control system for a simple model of a high-performance fighter is demonstrated as are the stability and performance improvements that can accrue with the technique.

Hess, R. A.↗