Results for “ocean deployment” — Page 14

NASA NTRS1988

Airborne lidar detection of subsurface oceanic scattering layers

The airborne lidar detection and cross-sectional mapping of submerged oceanic scattering layers are reported. The field experiment was conducted in the Atlantic Ocean southeast of Assateague Island, VA. NASA's Airborne Oceanographic Lidar was operated in the bathymetric mode to acquire on-wavelength 532-nm depth-resolved backscatter signals from shelf/slope waters. Unwanted laser pulse reflection from the air-water interface was minimized by spatial filtering and off-nadir operation. The presence of thermal stratification over the shelf was verified by the deployment of airborne expendable bathythermographs. Optical beam transmission measurements acquired from a surface truthing vessel indicated the presence of a layer of turbid water near the sea floor over the inner portion of the shelf.

Hoge, Frank E.↗

NASA NTRS2024

Expanded Signal to Noise Ratio Estimates for Validating Next-Generation Satellite Sensors in Oceanic, Coastal, and Inland Waters

The launch of the NASA Plankton, Aerosol, Cloud, ocean Ecosystem (PACE) and the Surface Biology and Geology (SBG) satellite sensors will provide increased spectral resolution compared to existing platforms. These new sensors will require robust calibration and validation datasets, but existing field-based instrumentation is limited in its availability and potential for geographic coverage, particularly for coastal and inland waters, where optical complexity is substantially greater than in the open ocean. The minimum signal-to-noise ratio (SNR) is an important metric for assessing the reliability of derived biogeochemical products and their subsequent use as proxies, such as for biomass, in aquatic systems. The SNR can provide insight into whether legacy sensors can be used for algorithm development as well as calibration and validation activities for next-generation platforms. We extend our previous evaluation of SNR and associated uncertainties for representative coastal and inland targets to include the imaging sensors PRISM and AVIRIS-NG, the airborne-deployed C-AIR radiometers, and the shipboard HydroRad and HyperSAS radiometers, which were not included in the original analysis. Nearly all the assessed hyperspectral sensors fail to meet proposed criteria for SNR or uncertainty in remote sensing reflectance (R rs ) for some part of the spectrum, with the most common failures (>20% uncertainty) below 400 nm, but all the sensors were below the proposed 17.5% uncertainty for derived chlorophyll-a. Instrument suites for both in-water and airborne platforms that are capable of exceeding all the proposed thresholds for SNR and R rs uncertainty are commercially available. Thus, there is a straightforward path to obtaining calibration and validation data for current and next-generation sensors, but the availability of suitable high spectral resolution sensors is limited.

signal-to-noise ratio↗

NASA NTRS2010

Two-Dimensional Synthetic-Aperture Radiometer

A two-dimensional synthetic-aperture radiometer, now undergoing development, serves as a test bed for demonstrating the potential of aperture synthesis for remote sensing of the Earth, particularly for measuring spatial distributions of soil moisture and ocean-surface salinity. The goal is to use the technology for remote sensing aboard a spacecraft in orbit, but the basic principles of design and operation are applicable to remote sensing from aboard an aircraft, and the prototype of the system under development is designed for operation aboard an aircraft. In aperture synthesis, one utilizes several small antennas in combination with a signal processing in order to obtain resolution that otherwise would require the use of an antenna with a larger aperture (and, hence, potentially more difficult to deploy in space). The principle upon which this system is based is similar to that of Earth-rotation aperture synthesis employed in radio astronomy. In this technology the coherent products (correlations) of signals from pairs of antennas are obtained at different antenna-pair spacings (baselines). The correlation for each baseline yields a sample point in a Fourier transform of the brightness-temperature map of the scene. An image of the scene itself is then reconstructed by inverting the sampled transform. The predecessor of the present two-dimensional synthetic-aperture radiometer is a one-dimensional one, named the Electrically Scanned Thinned Array Radiometer (ESTAR). Operating in the L band, the ESTAR employs aperture synthesis in the cross-track dimension only, while using a conventional antenna for resolution in the along-track dimension. The two-dimensional instrument also operates in the L band to be precise, at a frequency of 1.413 GHz in the frequency band restricted for passive use (no transmission) only. The L band was chosen because (1) the L band represents the long-wavelength end of the remote- sensing spectrum, where the problem of achieving adequate spatial resolution is most critical and (2) imaging airborne instruments that operate in this wavelength range and have adequate spatial resolution are difficult to build and will be needed in future experiments to validate approaches for remote sensing of soil moisture and ocean salinity. The two-dimensional instrument includes a rectangular array of patch antennas arranged in the form of a cross. The ESTAR uses analog correlation for one dimension, whereas the two-dimensional instrument uses digital correlation. In two dimensions, many more correlation pairs are needed and low-power digital correlators suitable for application in spaceborne remote sensing will help enable this technology. The two-dimensional instrument is dual-polarized and, with modification, capable of operating in a polarimetric mode. A flight test of the instrument took place in June 2003 and it participated in soil moisture experiments during the summers of 2003 and 2004.

LeVine, David M.↗

NASA NTRS2000

Coupling Satellite and Ground-Based Instruments to Map Climate Forcing by Anthropogenic Aerosols

Climate forcing by anthropogenic aerosols is a significant but highly uncertain factor in global climate change. Only satellites can offer the global coverage essential to reducing this uncertainty; however, satellite measurements must be coupled with correlative, in situ measurements both to constrain the aerosol optical properties required in satellite retrieval algorithms and to provide chemical identification of aerosol sources. This grant funded the first two years of a three-year project which seeks to develop methodologies for combining spaceborne lidar with in-situ aerosol data sets to improve estimates of direct aerosol climate forcing. Progress under this two-year grant consisted in the development and deployment of a new in-situ capability for measuring aerosol 180' backscatter and the extinction-to-backscatter ratio. This new measurement capacity allows definitive lidar/in-situ comparisons and improves our ability to interpret lidar data in terms of climatically relevant quantities such as the extinction coefficient and optical depth. Measurements were made along the coast of Washington State, in Central Illinois, over the Indian Ocean, and in the Central Pacific. Thus, this research, combined with previous measurements by others, is rapidly building toward a global data set of extinction-to-backscatter ratio for key aerosol types. Such information will be critical to interpreting lidar data from the upcoming PICASSO-CENA, or P-C, satellite mission. Another aspect of this project is to investigate innovative ways to couple the lidar-satellite signal with targeted in-situ measurements toward a direct determination of aerosol forcing. This aspect is progressing in collaboration with NASA Langley's P-C lidar simulator and radiative transfer modeling by the University of Lille, France.

Charlson, Robert J.↗

NASA NTRS2012

UARS Re-Entry Prediction and Analysis

The National Aeronautics and Space Administration (NASA) deployed the Upper Atmosphere Research Satellite (UARS) from the Space Shuttle payload bay during the STS-48 mission in September, 1991. The 5700 kg satellite was decommissioned in December, 2005 and was maneuvered into a lower altitude orbit to shorten its on-orbit lifetime to reduce the probability of a debris producing accidental collision. The satellite reentered the Earth s atmosphere over the Pacific Ocean on September 24, 2011. Analysis by NASA s Orbital Debris Program Office using the ORSAT software predicted that approximately two dozen fragments from UARS would survive reentry to reach the ground. This presentation will discuss the reentry predictions made in the days prior to the reentry and compare the UARS reentry with other historical reentries. It will also present the results of the ORSAT analysis showing predicted surviving reentry objects

Stansbery, Eugene G.↗

NASA NTRS1995

Results of Airborne Backscatter Measurements During the Surface Wave Dynamics Experiment

Ocean backscatter data over a wide variety of oceanic and atmospheric conditions were obtained by the Jet Propulsion Laboratory NUSCAT Ku-band scatterometer during the Surface Wave Dynamics Experiment (SWADE). Thirty hours of backscatter data were collected in ten flights by NUSCAT on the NASA Ames C130 aircraft during an intensive observation period (IOP) of SWADE in the winter of 1991. The SWADE experimental area, off the coast of Virginia and Maryland, was deployed with an array of buoys providing appropriate in-situ measurements to correlate with the radar backscatter for incidence angles from 10ø to 60ø at both horizontal and vertical polarizations.

Airborne↗

NASA NTRSDate not supplied

Exploring the Elevated Water Vapor Signal Associated With the Free Tropospheric Biomass Burning Plume Over the Southeast Atlantic Ocean

In southern Africa, widespread agricultural fires produce substantial biomass burning (BB) emissions over the region. The seasonal smoke plumes associated with these emissions are then advected westward over the persistent stratocumulus cloud deck in the southeast Atlantic (SEA) Ocean, resulting in aerosol effects which vary with time and location. Much work has focused on the effects of these aerosol plumes, but previous studies have also described an elevated free tropospheric water vapor signal over the SEA. Water vapor influences climate in its own right, and it is especially important to consider atmospheric water vapor when quantifying aerosol–cloud interactions and aerosol radiative effects. Here we present airborne observations made during the NASA ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) campaign over the SEA Ocean. In observations collected from multiple independent instruments on the NASA P-3 aircraft (from near-surface to 6–7 km), we observe a strongly linear correlation between pollution indicators (carbon monoxide (CO) and aerosol loading) and atmospheric water vapor content, seen at all altitudes above the boundary layer. The focus of the current study is on the especially strong correlation observed during the ORACLES-2016 deployment (out of Walvis Bay, Namibia), but a similar relationship is also observed in the August 2017 and October 2018 ORACLES deployments. Using reanalyses from the European Centre for Medium-Range Weather Forecasts (ECMWF) and Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2), and specialized WRF-Chem simulations, we trace the plume–vapor relationship to an initial humid, smoky continental source region, where it mixes with clean, dry upper tropospheric air and then is subjected to conditions of strong westward advection, namely the southern African easterly jet (AEJ-S). Our analysis indicates that air masses likely left the continent with the same relationship between water vapor and carbon monoxide as was observed by aircraft. This linear relationship developed over the continent due to daytime convection within a deep continental boundary layer (up to ∼5–6 km) and mixing with higher-altitude air, which resulted in fairly consistent vertical gradients in CO and water vapor, decreasing with altitude and varying in time, but this water vapor does not originate as a product of the BB combustion itself. Due to a combination of conditions and mixing between the smoky, moist continental boundary layer and the dry and fairly clean upper-troposphere air above (∼6 km), the smoky, humid air is transported by strong zonal winds and then advected over the SEA (to the ORACLES flight region) following largely isentropic trajectories. Hybrid Single-Particle Lagrangian Integrated Trajectory model (HYSPLIT) back trajectories support this interpretation. This work thus gives insights into the conditions and processes which cause water vapor to covary with plume strength. Better understanding of this relationship, including how it varies spatially and temporally, is important to accurately quantify direct, semi-direct, and indirect aerosol effects over this region.

Kristina Pistone↗

NASA NTRSDate not supplied

Tracking and Recovery of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Reentry Vehicle (RV)

The LOFTID mission launched from Vandenberg on Nov 10, 2022, and successfully demonstrated the reentry of a 6m diameter inflatable aeroshell from low Earth orbit. This paper will cover the design features implemented to enable recovery of the flight vehicle, and will discuss the splashdown calculations, in-flight tracking, recovery from the ocean, and post-flight inspection of the flight vehicle. To support recovery of the RV and ejected data recorder after splashdown, a recovery ship was pre-positioned near the predicted splashdown ellipse in the Pacific Ocean. The splashdown ellipse was repeatedly updated as launch approached. In-flight tracking included transmission from the RV of GPS data through both the Iridium satellite network and the LoRa direct RF link, along with IR video cameras on the recovery ship and airborne imagery from the SCIFLI Team. Using both the GPS data and the IR imagery, the recovery ship tracked down the RV, and deployed an inflatable boat to approach the RV and attach it to the ship’s crane, after which the RV was hoisted on board and secured in its GSE recovery stand. The ship then tracked down the ejected data recorder, which was also broadcasting its GPS data, and pulled it from the water. Once the ship returned to port, the RV was hoisted ashore for additional inspection, removal of the data recorders, and repackaging for shipment back to NASA Langley.

Robert A. Dillman↗

NASA NTRSDate not supplied

Tracking and Recovery of the LOFTID RV (Low-Earth Orbit Flight Test of an Inflatable Decelerator Reentry Vehicle)

The LOFTID mission launched from Vandenberg on Nov 10, 2022, and successfully demonstrated the reentry of a 6m diameter inflatable aeroshell from low Earth orbit. This paper will cover the design features implemented to enable recovery of the flight vehicle, and will discuss the splashdown calculations, in-flight tracking, recovery from the ocean, and post-flight inspection of the flight vehicle. To support recovery of the RV and ejected data recorder after splashdown, a recovery ship was pre-positioned near the predicted splashdown ellipse in the Pacific Ocean. The splashdown ellipse was repeatedly updated as launch approached. In-flight tracking included transmission from the RV of GPS data through both the Iridium satellite network and the LoRa direct RF link, along with IR video cameras on the recovery ship and airborne imagery from the SCIFLI Team. Using both the GPS data and the IR imagery, the recovery ship tracked down the RV, and deployed an inflatable boat to approach the RV and attach it to the ship’s crane, after which the RV was hoisted on board and secured in its GSE recovery stand. The ship then tracked down the ejected data recorder, which was also broadcasting its GPS data, and pulled it from the water. Once the ship returned to port, the RV was hoisted ashore for additional inspection, removal of the data recorders, and repackaging for shipment back to NASA Langley.

Robert A Dillman↗

NASA NTRS2009

Microstrip Antenna for Remote Sensing of Soil Moisture and Sea Surface Salinity

This compact, lightweight, dual-frequency antenna feed developed for future soil moisture and sea surface salinity (SSS) missions can benefit future soil and ocean studies by lowering mass, volume, and cost of the antenna system. It also allows for airborne soil moisture and salinity remote sensors operating on small aircraft. While microstrip antenna technology has been developed for radio communications, it has yet to be applied to combined radar and radiometer for Earth remote sensing. The antenna feed provides a key instrument element enabling high-resolution radiometric observations with large, deployable antennas. The design is based on the microstrip stacked-patch array (MSPA) used to feed a large, lightweight, deployable, rotating mesh antenna for spaceborne L-band (approximately equal to 1 GHz) passive and active sensing systems. The array consists of stacked patches to provide dual-frequency capability and suitable radiation patterns. The stacked-patch microstrip element was designed to cover the required L-band center frequencies at 1.26 GHz (lower patch) and 1.413 GHz (upper patch), with dual-linear polarization capabilities. The dimension of patches produces the required frequencies. To achieve excellent polarization isolation and control of antenna sidelobes for the MSPA, the orientation of each stacked-patch element within the array is optimized to reduce the cross-polarization. A specialized feed-distribution network was designed to achieve the required excitation amplitude and phase for each stacked-patch element.

Ramhat-Samii, Yahya↗

NASA NTRS2024

Vertical Structure of a Springtime Smoky and Humid Troposphere Over the Southeast Atlantic From Aircraft and Reanalysis

The springtime atmosphere over the southeast Atlantic Ocean (SEA) is subjected to a consistent layer of biomass burning (BB) smoke from widespread fires on the African continent. An elevated humidity signal is coincident with this layer, consistently proportional to the amount of smoke present. The combined humidity and BB aerosol has potentially significant radiative and dynamic impacts. Here, we use aircraft-based observations from the NASA ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) deployments in conjunction with reanalyses to characterize covariations in humidity and BB smoke across the SEA. The observed plume–vapor relationship, and its agreement with the European Centre for Medium-Range Weather Forecasts (ECMWF) Reanalysis version 5 (ERA5) and Copernicus Atmosphere Monitoring Service (CAMS) reanalysis, persists across all observations, although the magnitude of the relationship varies as the season progresses. Water vapor is well represented by the reanalyses, while CAMS tends to underestimate carbon monoxide especially under high BB. While CAMS aerosol optical depth (AOD) is generally overestimated relative to ORACLES AOD, the observations show a consistent relationship between carbon monoxide (CO) and aerosol extinction, demonstrating the utility of the CO tracer to understanding vertical aerosol distribution. We next use k-means clustering of the reanalyses to examine multi-year seasonal patterns and distributions. We identify canonical profile types of humidity and of CO, allowing us to characterize changes in vapor and BB atmospheric structures, and their impacts as they covary. While the humidity profiles show a range in both total water vapor concentration and in vertical structure, the CO profiles primarily vary in terms of maximum concentration, with similar vertical structures in each. The distribution of profile types varies spatiotemporally across the SEA region and through the season, ranging from largely one type in the northeast and southwest to more evenly distributed between multiple types where air masses meet in the middle of the SEA. These distributions follow patterns of transport from the humid, smoky source region (greatest influence in the northeast of the SEA) and the seasonal changes in both humidity and smoke (increasing and decreasing through the season, respectively). With this work, we establish a framework for a more complete analysis of the broader radiative and dynamical effects of humid aerosols over the SEA.

Kristina Pistone↗

NASA NTRS1991

Wave propagation in the marginal ice zone - Model predictions and comparisons with buoy and synthetic aperture radar data

Ocean wave dispersion relation and viscous attenuation by a sea ice cover are studied for waves propagating into the marginal ice zone (MIZ). The Labrador ice margin experiment (LIMEX), conducted on the MIZ off the east coast of Newfoundland, Canada in March 1987, provided aircraft SAR imagery, ice property and wave buoy data. Wave energy attenuation rates are estimated from SAR data and the ice motion package data that were deployed at the ice edge and into the ice pack, and compared with a model. It is shown that the model data comparisons are quite good for the ice conditions observed during LIMEX 1987.

Liu, Antony K.↗

NASA NTRSDate not supplied

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗

NASA NTRSDate not supplied

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗

NASA NTRS1997

Inversion Schemes to Retrieve Atmospheric and Oceanic Parameters from SeaWiFS Data

The investigation focuses on two key issues in satellite ocean color remote sensing, namely the presence of whitecaps on the sea surface and the validity of the aerosol models selected for the atmospheric correction of SeaWiFS data. Experiments were designed and conducted at the Scripps Institution of Oceanography to measure the optical properties of whitecaps and to study the aerosol optical properties in a typical mid-latitude coastal environment. CIMEL Electronique sunphotometers, now integrated in the AERONET network, were also deployed permanently in Bermuda and in Lanai, calibration/validation sites for SeaWiFS and MODIS. Original results were obtained on the spectral reflectance of whitecaps and on the choice of aerosol models for atmospheric correction schemes and the type of measurements that should be made to verify those schemes. Bio-optical algorithms to remotely sense primary productivity from space were also evaluated, as well as current algorithms to estimate PAR at the earth's surface.

Deschamps, P.-Y.↗

NASA NTRS2004

Processing of High Resolution, Multiparametric Radar Data for the Airborne Dual-Frequency Precipitation Radar APR-2

Following the successful Precipitation Radar (PR) of the Tropical Rainfall Measuring Mission, a new airborne, 14/35 GHz rain profiling radar, known as Airborne Precipitation Radar - 2 (APR-2), has been developed as a prototype for an advanced, dual-frequency spaceborne radar for a future spaceborne precipitation measurement mission. . This airborne instrument is capable of making simultaneous measurements of rainfall parameters, including co-pol and cross-pol rain reflectivities and vertical Doppler velocities, at 14 and 35 GHz. furthermore, it also features several advanced technologies for performance improvement, including real-time data processing, low-sidelobe dual-frequency pulse compression, and dual-frequency scanning antenna. Since August 2001, APR-2 has been deployed on the NASA P3 and DC8 aircrafts in four experiments including CAMEX-4 and the Wakasa Bay Experiment. Raw radar data are first processed to obtain reflectivity, LDR (linear depolarization ratio), and Doppler velocity measurements. The dataset is then processed iteratively to accurately estimate the true aircraft navigation parameters and to classify the surface return. These intermediate products are then used to refine reflectivity and LDR calibrations (by analyzing clear air ocean surface returns), and to correct Doppler measurements for the aircraft motion. Finally, the the melting layer of precipitation is detected and its boundaries and characteristics are identifIed at the APR-2 range resolution of 30m. The resulting 3D dataset will be used for validation of other airborne and spaceborne instruments, development of multiparametric rain/snow retrieval algorithms and melting layer characterization and statistics.

airborne radar↗

NASA NTRS1986

Interpretation of satellite elevation magnetic anomalies

The present discussion is based on a study of the magnetic field data obtained with the aid of the magnetic field satellite Magsat, deployed in October 1979, over most of the earth during a 7.5-month mission. Inversions using spherical harmonic coefficients are considered along with the inversion of residual fields. In order to perform the correct operation, it is necessary to add on to the source function produced by the inversion process a magnetization function which has no external field. Such a function is known as an annihilator. The use of the annihilator for Pacific Ocean anomalies is discussed. Attention is given to models of oceanic crustal magnetization, and continental long-wavelength anomalies. It is found that in continental regions the annihilator is also useful if induced magnetizations are thought to be responsible for the long-wavelength anomaly.

Harrison, C. G. A.↗

NASA NTRS1999

Monsoon Convection during the South China Sea Monsoon Experiment Observed from Shipboard Radar and the TRMM Satellite

A main goal of the recent South China Sea Monsoon Experiment (SCSMEX) was to study convective processes associated with the onset of the Southeast Asian summer monsoon. The NASA TOGA C-band scanning radar was deployed on the Chinese research vessel Shi Yan #3 for two 20 day cruises, collecting dual-Doppler measurements in conjunction with the BMRC C-Pol dual-polarimetric radar on Dongsha Island. Soundings and surface meteorological data were also collected with an NCAR Integrated Sounding System (ISS). This experiment was the first major tropical field campaign following the launch of the Tropical Rainfall Measuring Mission (TRMM) satellite. These observations of tropical oceanic convection provided an opportunity to make comparisons between surface radar measurements and the Precipitation Radar (PR) aboard the TRMM satellite in an oceanic environment. Nearly continuous radar operations were conducted during two Intensive Observing Periods (IOPS) straddling the onset of the monsoon (5-25 May 1998 and 5-25 June 1998). Mesoscale lines of convection with widespread regions of both trailing and forward stratiform precipitation were observed during the active monsoon periods in a southwesterly flow regime. Several examples of mesoscale convection will be shown from ship-based and spacebome radar reflectivity data during times of TRMM satellite overpasses. Further examples of pre-monsoon convection, characterized by isolated cumulonimbus and shallow, precipitating congestus clouds, will be discussed. A strong waterspout was observed very near the ship from an isolated cell in the pre-monsoon period, and was well documented with photography, radar, sounding, and sounding data.

Rickenbach, Tom↗