Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗
DOE OSTI2025

Investigating the effect of heterogeneities across the electrode|multiphase polymer electrolyte interfaces in high-potential lithium batteries

Polymer electrolytes hold great promise for safe and high-energy batteries comprising solid or semi-solid electrolytes. Multiphase polymer electrolytes, consisting of mobile and rigid phases, exhibit fast ion conduction and desired mechanical properties. However, fundamental challenges exist in understanding and regulating interactions at the electrode|electrolyte interface, especially when using high-potential layered oxide active materials at the positive electrode. Here we demonstrate that depletion of the mobile conductive phase at the interface contributes to battery performance degradation. Molecular ionic composite electrolytes, composed of a rigid-rod ionic polymer with nanometric mobile cations and anions, serve as a multiphase platform to investigate the evolution of ion conductive domains at the interface. Chemical and structural characterizations enable the visualization of concentration heterogeneity and spatially resolve the interfacial chemical states over a statistically significant field of view for buried interfaces. We report that concentration and chemical heterogeneities prevail at electrode|electrolyte interfaces, leading to phase separation in polymer electrolytes. In conclusion, understanding the hidden roles of interfacial chemomechanics in polymer electrolytes enables us to design an interphase tailoring strategy based on electrolyte additives to mitigate the interfacial heterogeneity and improve battery performance.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Investigating PVC polymer–plasticizer interactions with atomistic MD simulations and potential of mean force calculations

For this work, atomistic molecular dynamics (MD) simulations coupled with potential of mean force (PMF) calculations were employed to investigate the interactions between PVC polymer chains containing 6–20 repeating units and various plasticizers, with the goal of identifying potential replacements for the toxic plasticizer di(2-ethylhexyl)phthalate (DEHP) used in blood bags. The selected plasticizers belong to various chemical families, such as orthophthalates, citrates, adipates, and the terephthalate DEHT. Both the polymer and the plasticizers lack ionizable groups, and their interactions are primarily governed by van der Waals and electrostatic forces. A model correlating PMF profiles with interaction forces was developed and validated across polyvinyl chloride (PVC) polymers of different lengths and all investigated plasticizers. This model provides insight into how structural variations in plasticizers influence their respective PMF values. The study ranks the investigated plasticizers based on binding affinity, identifying TOTM (tris(2-ethylhexyl) trimellitate, TEHTM), BTHC (butyryl trihexyl citrate, Citroflex B-6), ATHC (acetyl trihexyl citrate, Citroflex A-6, CA-6), and DEHT (bis(2-ethylhexyl)terephthalate, DOTP/DEHTP) as promising alternatives for further investigation. This comprehensive study encompasses PVC polymers of four different lengths and 14 plasticizers, with all data averaged over 30 independent simulations. The approach provides a deeper understanding of molecular interactions, enabling the tailoring of polymer–plasticizer systems for diverse applications, including extractables and leachables, with relevance spanning materials science to biomedical engineering, and also serves as a basis for developing coarse-grained simulation protocols. Overall, this study provides valuable insights for designing safer and more efficient plasticizer substitutes and is well supported by other studies.

Shet, Sai Athmeeya G. [Sri Sathya Sai Institute of↗
DOE OSTI2026

A divergent synthetic route to functional copolymer libraries via modular polymers

High-throughput polymer synthesis enables rapid exploration of chemical space but remains limited by batch-to-batch inconsistencies that can obscure structure–property relationship trends. To address this challenge, we developed a synthetic approach to produce multifunctional copolymers using post-polymerization modification of activated ester modular polymers with commercially available amines. Easily derivitized parent polymers—poly(tetrafluorophenyl acrylate) and poly(tetrafluorophenyl styrene sulfonate)—were synthesized by RAFT polymerization to yield single polymer batches containing highly reactive tetrafluorophenyl esters or sulfonate esters on each repeat unit. Tuning post-polymerization modification reaction conditions enabled the addition of sub-stoichiometric amounts of amines (relative to the repeat unit) to yield partially functionalized intermediates that could then be further derivatized. Reaction monitoring by 19 F NMR spectroscopy confirmed good control over these sequential post-polymerization modifications. This synthetic route produced a variety of copolymers with defined comonomer ratios while preserving the underlying polymer structure (degree of polymerization, dispersity, tacticity) for both the acrylate and styrene sulfonate backbones. We further applied this approach in a divergent manner to create a small library of structurally distinct copolymers from a single parent batch in three synthetic steps. This modular, divergent synthesis demonstrates a general route to structurally consistent copolymer libraries that enable systematic studies of structure–property relationships and can accelerate functional materials discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Electrospinning of ultra-high molecular weight polymers into aligned nanofibers and their application in chemical separations

Ultra-high molecular weight (UHMW, >10 6 g mol −1 ) vinyl polymers are increasingly accessible through photoiniferter polymerization, yet their behavior in electrospinning has received comparatively little attention. Here, we explore the electrospinning of UHMW poly(methyl acrylate), poly(methyl methacrylate), poly(N,N-dimethylacrylamide), and poly(styrene-co-pentafluorostyrene) synthesized by photoiniferter polymerization, with number-average molecular weights (M n ) greater than 1000 kDa and dispersities below 1.4. UHMW polymers form stable Taylor cones and discrete fibers at solution concentrations as low as 0.5 wt% due to their large number of entanglements, a threshold unachievable with low molecular weight (M n = 20–54 kDa) polymers of the same chemistry. Using poly(methyl methacrylate) and poly(styrene-co-pentafluorostyrene) as model systems, we demonstrate that fiber diameter can be tuned from 350 nm to 20 μm through systematic variation of polymer concentration (0.01 to 4 wt%) and flow rate (0.5 to 10 mL h −1 ). Additionally, we find that collector rotation rate governs fiber alignment, with highly aligned mats obtained with drum rotation speeds of 1000 RPM. Reversing the polarity of the electric field during electrospinning reorients the surface chemistry of these fiber mats without altering their microscale morphology, shifting the water contact angle by 7° (89° to 96°) and providing a two-fold binding capacity enhancement in cationic dye uptake. These results show that the high entanglement densities of UHMW vinyl polymers shift the accessible electrospinning window to dilute solutions and that electric-field polarity is a useful lever to control the surface chemistry in the resulting fibers.

Marquez, Joshua D. [University of Florida, Gainesv↗
DOE OSTI2025

Ion Transport in Concentrated Crosslinked Solid Polymer Electrolytes

Crosslinking polymers is a common approach to create mechanically stable solid materials such as polymer electrolytes for lithium batteries. In conventional liquid electrolytes, the solvent molecules move freely to accommodate the field-induced motion of ions. However, in crosslinked polymer electrolytes, the rearrangement of polymer segments is constrained by the deformation limits of the network. Herein, we develop a new transport model that accounts for both the formation of concentration gradients and the elasticity of the electrolyte. The elasticity is incorporated by adding an additional term related to the entropy of crosslinked strands to the electrochemical potential of the salt. The resulting Crosslink Model contains two adjustable parameters: $\mathcal{N}$, the average number of monomers in a strand, and λ crit , the maximum strain the network can sustain. These solid-like constraints produce singularities in the governing transport equations, fundamentally altering the concentration profiles. Plateaus in salt concentrations emerge near the electrodes, and network elasticity introduces a strain overpotential. When compared to a Baseline Model ($\mathcal{N}$ → ∞, equivalent to concentrated solution theory), which predicts steepest gradients near the electrodes, both models yield similar current–voltage relationships. Model predictions are compared to electrochemical data for a poly(ethylene oxide)-based crosslinked polymer electrolyte.

Patel, Vivaan [University of California, Berkeley,↗
DOE OSTI2024

Infinitely Recyclable Network Polymers, Enabling Sustainable Manufacturing (CRADA Final Report)

This FLO Materials project was aimed at commercializing a new, infinitely recyclable material that can enable closed-loop lifecycles for hard-to-recycle plastics and plastic products. Four hundred million metric tons of virgin plastic is produced each year, yet less than 10% of this material is recycled. In the US alone, 2% of energy consumption is dedicated to the manufacture of virgin plastics, polymer resin, and synthetic rubbers. By keeping plastic materials in circulation longer, we can reduce waste, lower manufacturing costs, cut energy and oil consumption, and drastically reduce greenhouse gas (GHG) emissions. Specifically, FLO’s innovation overcomes the complications associated with salvaging difficult-to-recycle plastics (i.e., contaminated thermoplastic linear polymers, thermoset cross-linked network polymers), which represent at least 20% of total polymer global production, with a recycling rate of near 0%. Chemical recycling of these new polymers through depolymerization allows all additives to be easily removed at room temperature and the recovered monomers to be remanufactured into next generation materials with 100% recovery of mechanical performance and aesthetic quality.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Preparation of prepreg graphite tape with insoluble polymer

Powdered polymer is finely ground. Second polymer, soluble, is mixed with appropriate solvent. Milled polymer and graphite filaments are added to soluble polymer-solvent solution to create slurry. Slurry is dried, and when ready for processing, the soluble, binder-polymer is removed by heat during precure or cure cycle.

Yates, C. I.↗
NASA NTRS1974

Ultraviolet and thermally stable polymer compositions

A class of polymers is provided, namely, poly(diarylsiloxy) arylazines. These polymers have a basic chemical composition which has the property of stabilizing the optical and physical properties of the polymer against the degradative effect of ultraviolet light and high temperatures. This stabilization occurs at wavelengths including those shorter than found on the surface of the earth and in the absence or presence of oxygen, making the polymers of the present invention useful for high performance coating applications in extraterrestrial space as well as similar applications in terrestrial service. The invention also provides aromatic azines which are useful in the preparation of polymers such as those of the present invention.

Reinisch, R. F.↗
NASA NTRS1974

Solubilization and spore recovery from silicone polymers

A non-sporicidal technique for solvent degradation of cured silicone polymers was developed which involves chemical degradation of cured silicone polymers by amine solvents at room temperature. Substantial improvements were obtained in the recovery of seeded spores from room temperature cured polymers as compared to the standard recovery procedures, which indicates that the curing process is not sufficiently exothermic to reduce spore viability. The dissolution reaction of cured silicone polymers whith amine solvents is proposed to occur by bimolecular nucleophilic displacement. The chemical structure of silicone polymers was determined by spectroscopic methods. The phenyl to methyl ratio, R/Si ratio, molecular weight, and hydroxyl content of the silicone resins were determined.

Hsiao, Y. C.↗
NASA NTRS1976

Ultraviolet and thermally stable polymer compositions

A new class of polymers is provided, namely, poly (diarylsiloxy) arylazines. These novel polymers have a basic chemical composition which has the property of stabilizing the optical and physical properties of the polymer against the degradative effect of ultraviolet light and high temperatures. This stabilization occurs at wavelengths including those shorter than found on the surface of the earth and in the absence or presence of oxygen, making the polymers useful for high performance coating applications in extraterrestrial space as well as similar applications in terrestrial service. The invention also provides novel aromatic azines which are useful in the preparation of polymers such as those described.

Reinisch, R. F.↗
NASA NTRS1976

A model for the pyrolysis of unfilled and filled polymers and comparisons with NBS smoke-density chamber data

This paper considers a model for the pyrolysis of polymers for use in mass loss and smoke density predictions in a fire situation. It is based on the fundamental postulate that the overall rate-limiting reactions are in the relatively low temperature condensed phase; the rate limiting step is the polymer degradation to a vaporizable state. The state of the polymer (chain length) at the surface is specified by the vapor pressure equilibrium criterion. For the case of polymers with inert fillers, like alumina trihydrate, the further assumption is made that the linear regression rate of the material is identical to the unfilled material's at the same surface temperature. The fraction of polymer mass loss converted to smoke is inferred from the literature. The smoke density in the NBS-smoke density chamber is predicted for a polyester and the same polyester with two different loads of alumina trihydrate filler. Diffusional effects in the smoke spreading are considered in an elementary manner. The comparisons with experimental data are encouraging. The overall fire characteristics are predicted using only the fundamental physicochemical property values of ingredients.

Kumar, R. N.↗
NASA NTRS1977

Origin of organic matter in the early solar system. VII - The organic polymer in carbonaceous chondrites

Degradation techniques, including pyrolysis, depolymerization, and oxidation, were used to study the insoluble polymer from the Murchison C2 chondrite. Oxidation with Cr2O7(2-) or O2/UV led to the identification of 15 aromatic ring systems. Of 11 aliphatic acids identified, three dicarboxylic acids presumably came from hydroaromatic portions of the polymer, whereas eight monocarboxylic acids probably derive from bridging groups or ring substituents. Depolymerization with CF3COO4 yielded some of the same ring systems, as well as alkanes (C1 through C8) and alkenes (C2 through C8), alkyl (C1 through C5) benzenes and naphthalenes, and methyl- or dimethyl -indene, -indane, -phenol, -pyrrole, and -pyridine. All these compounds were detected below 200 C, and are therefore probably indigenous constituents. The properties of the meteoritic polymer were compared with the properties of a synthetic polymer produced by the Fischer-Tropsch reaction. It is suggested that the meteoritic polymer was also produced by surface catalysis.

Hayatsu, R.↗
NASA NTRS1978

Toxicity of pyrolysis gases from some cellular polymers

Various samples of cellular polymers were evaluated for toxicity of pyrolysis gases, using the screening test method developed at the University of San Francisco. The cellular polymer samples included polyimide, polymethacrylimide, polybismaleimide, polyurethane, polyisocyanurate, polyethylene, polychloroprene, polyvinyl chloride, polystyrene, polysiloxane, and polyphosphazene. The cellular polymers exhibited varying levels of toxicity under these test conditions. Among the rigid cellular polymers, times to death were shortest with the imide type foams and longest with polyvinyl chloride and polystyrene. Among the flexible cellular polymers, times to death were shortest with polyimide and polyester, and longest with polychloroprene and polysiloxane. Increased char yield was not necessarily associated with reduced toxicity.

Hilado, C. J.↗
NASA NTRS1978

Thermal rearrangements of unsaturated polymers

Thermal anaerobic uncatalyzed cyclizations and cis-trans isomerizations observed in unsaturated hydrocarbon polymers are surveyed. Three main types of cyclizations are described. Type I is a radical reaction which is caused by chain rupture and gives rise to six-membered rings; this reaction occurs during pyrolysis of polymers with double bonds in a 1,5- or 1,6-diene configuration. Type II is a (2 + 2) thermal cycloaddition of double bonds in certain polymers with a 1,6-diene structure; bicycloheptane structures result. Type III is an intramolecular ene reaction. Many polymers containing a double bond linking CH units display thermal cis-trans isomerization. The common activation energy is approximately 130 kJ/mol, and the initial rate constants are lower, for homologous polymers, the greater the separation of the carbon-carbon double bonds.

Golub, M. A.↗
NASA NTRS1981

Incorporation of metal related materials into electrically neutral polymers

Developments in the field of metal-containing polymers are reviewed with emphasis on neutral polymers incorporating dissolved metal salts, metal complexes, organometallic compounds, and metals. Polymer systems discussed include: polyamides, polyimides, polyalcohols, polyesters, polyacetylene, polyethylene, and polysiloxane. Most of the studies focus on the modification of polymer properties such as adhesive properties, thermal behavior, electrical conductivity, polymer flammability, and mechanical properties.

St. Clair, A. K.↗
NASA NTRS1984

Characterization and measurement of polymer wear

Analytical tools which characterize the polymer wear process are discussed. The devices discussed include: visual observation of polymer wear with SEM, the quantification with surface profilometry and ellipsometry, to study the chemistry with AES, XPS and SIMS, to establish interfacial polymer orientation and accordingly bonding with QUARTIR, polymer state with Raman spectroscopy and stresses that develop in polymer films using a X-ray double crystal camera technique.

Buckley, D. H.↗
NASA NTRS1985

Monte Carlo lattice models for adsorbed polymer conformation

The adhesion between a polymer film and a metal surface is of great technological interest. However, the prediction of adhesion and wear properties of polymer coated metals is quite difficult because a fundamental understanding of the polymer surface interaction does not yet exist. A computer model for the conformation of a polymer molecule adsorbed on a surface is discussed. The chain conformation is assumed to be described by a partially directed random walk on a three dimensional simple cubic lattice. An attractive surface potential is incorporated into the model through the use of a random walk step probability distribution that is anisotropic in the direction normal to the attractive surface. The effects of variations in potential characteristics are qualitatively included by varying both the degree of anisotropy of the step distribution and the range of the anisotropy. Polymer conformation is characterized by the average end to end distance, average radius of gyration, and average number of chain segments adsorbed on the surface.

Good, B. S.↗