Search NASA⌕ Search

SEARCH · Search NASA

Results for “pore water”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Role of heterogeneous surface wettability on dynamic immiscible displacement, capillary pressure, and relative permeability in a CO 2 -water-rock system

Numerical examination of CO 2 displacement in brine filled rock pores with varying wettability. Results show that as the CO 2 contact angles on the rock surface increased (intermediate water wetting conditions) negative entry pressures for CO 2 displacement were observed, indicating that when heterogeneous surface wettability is accounted for, greater mobility of CO 2 into rock pores is expected. In addition, simulated relative permeability CO 2 curves with heterogeneous intermediate water wetting conditions exhibited a greater amount of variation, indicative of a complex interrelation of geometric capillary restrictions and surface wettability.

58 GEOSCIENCES↗
DOE OSTI2020

Fluid Behavior in Nanoporous Silica

We investigate dynamics of water (H 2 O) and methanol (CH 3 OH and CH 3 OD) inside mesoporous silica materials with pore diameters of 4.0, 2.5, and 1.5 nm using low-field (LF) nuclear magnetic resonance (NMR) relaxometry. Experiments were conducted to test the effects of pore size, pore volume, type of fluid, fluid/solid ratio, and temperature on fluid dynamics. Longitudinal relaxation times (T 1 ) and transverse relaxation times (T 2 ) were obtained for the above systems. We observe an increasing deviation in confined fluid behavior compared to that of bulk fluid with decreasing fluid-to-solid ratio. Our results show that the surface area-to-volume ratio is a critical parameter compared to pore diameter in the relaxation dynamics of confined water. An increase in temperature for the range between 25 and 50°C studied did not influence T 2 times of confined water significantly. However, when the temperature was increased, T 1 times of water confined in both silica-2.5 nm and silica-1.5 nm increased, while those of water in silica-4.0 nm did not change. Reductions in both T 1 and T 2 values as a function of fluid-to-solid ratio were independent of confined fluid species studied here. The parameter T 1 /T 2 indicates that H 2 O interacts more strongly with the pore walls of silica-4.0 nm than CH 3 OH and CH 3 OD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Pore-Scale Oil Connectivity and Displacement by Controlled-Ionic-Composition Waterflooding Using Synchrotron X-Ray Microtomography

Controlled-ionic-composition waterflooding is an economic and effective method to improve oil recovery in carbonate oil reservoirs. Recent studies show controlling the salinity and ionic composition of injection water can alter the wettability of carbonate mineral surfaces. The pore-scale oil connectivity and displacement by controlled-ionic-composition waterflooding in heterogeneous carbonate reservoirs, especially at the early stage, is still unclear. The goal of this study is to examine the role of ion concentrations and types in the oil displacement efficiency and investigate the impact of the waterflooding on the pore-scale oil displacement using the national synchrotron facility. A carbonate rock sample was flooded with synthetic high-salinity water and other water solutions with different sulfate concentrations. The waterflooding processes were visualized with synchrotron X-ray microtomography to follow the evolution of pore-scale oil/brine interactions at typical field flow rates. Experimental results show that the water with lower sulfate concentration and higher salinity did not change the wettability of the pore surfaces. Higher sulfate ion concentrations in the water, in contrast, altered the wettability of carbonate pore surfaces from oil-wet to neutral-wet within the first few minutes of waterflooding. Finally, novel insight was gained on the ability of water with high-sulfate concentration to displace oil in the small pores and through abundant oil channels, which could consequently lead to higher oil recovery from the carbonate rock.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2024

Fuel Cell Membrane Electrode Assemblies with Ultra-Low Pt Nanofiber Electrodes (Final Report)

H 2 /air fuel cell membrane-electrode-assemblies (MEAs) were fabricated with electrospun particle/polymer nanofiber mat cathodes (0.1 mg Pt /cm 2 or 0.2 mg Pt /cm 2 Pt/C, PtCo/C or PtNi/C) and anodes (0.1 mg/cm 2 Pt/C), where the binder was a mixture of acid-form perfluorosulfonic acid ionomer (e.g., Nafion™) and poly(acrylic acid) (PAA) carrier polymer or sodium-form PFSA with a carrier polymer of either PAA or polyethylene oxide (PEO). For the latter two cases, the water-soluble carrier was removed from the fibers after electrospinning. MEAs with Pt/C anode/cathode catalyst loadings of 0.1 mg Pt /cm2 each, an 1100 EW PFSA binder (Nafion™ dispersion), and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions, e.g., a maximum power density of 919 mW/cm 2 at 100% RH and 832 mW/cm 2 at 40% RH for a test at 80 °C and 200 kPa abs . The high power at low RH was attributed to nm-size pores within the fibers that trap water via capillary condensation thus maintaining a high proton conductivity of the PFSA binder in the cathode and especially the anode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder. At the same time, micro-porosity between fibers in the cathode allows for fast removal of electrogenerated water, thus minimizing cathode flooding. Nanofiber MEAs with Pt alloy catalyst cathodes also performed well, where a fibrous PtCo/C catalyst cathode at a loading of 0.1 mg/cm 2 produced 20% more power than a conventional powder cathode MEA, e.g., a maximum power density of 1,045 mW/cm 2 vs. 869 mW/cm 2 at 80 °C, 100% RH, and 200 kPa abs , and a PtNi/C fiber cathode MEAs prepared with Na+-form Nafion + PEO generated a maximum power of 820 mW/cm 2 at 40% RH. Fiber electrode MEAs with a neat Nafion binder (prepared from Na+-form Nafion + PEO or PAA) where the cathode Pt loading was ~0.1 mg/cm 2 exhibited a 25% loss in maximum power at 30,000 metal dissolution cycles, as compared to a 12% loss when the cathode binder was H+-form Nafion + PAA. The performance of a fiber mat electrode MEA with Pt/C catalyst (0.2 mg/cm 2 cathode loading and 0.1 mg/cm 2 anode loading) was excellent. At 80 oC and 200 kPa abs , the maximum power density was 1104 mW/cm 2 . The maximum power was independent of feed gas humidity for 40 < RH < 100%. The power loss after a metal dissolution AST (30,000 voltage cycles) was only 13%.

08 HYDROGEN↗
DOE OSTI2022

Non-equilibrium molecular dynamics simulation to evaluate the effect of confinement on fluid flow in silica nanopores

The flow of fluids in nano-confinement has applications in separations, water purification, medical systems and in the recovery of fluids in petroleum systems. It is believed that fluids do not obey continuum laws when flowing in nanopores (or in confinement). This paper attempts to shed light on various nano confinement effects such as fluid-wall interactions, pore size and molecular geometry, using molecular dynamic simulation. Here, water, hexane, and methanol flow behaviors were simulated for pore diameters ranging from 1 to 8 nm. In addition to the density analysis of the confined fluids, the fluid flows in saturated nanopores were simulated by the sectional flow method. Water and methanol molecules were completely stabilized in the 1 nm pore. Hexane molecules could not enter the 1 nm pore, due to geometric considerations. For the 2 – 8 nm pores, all fluids showed reduced flow rate compared to the Hagen–Poiseuille flow, due to an interfacial molecular layer stabilized at the pore surface. Flow reduction observed in these studies is contrary to significant flow enhancements observed for fluid flow in carbon nanotubes of similar dimensions. Water flow showed almost constant stick length for all the pore sizes. Methanol flow had the largest stick length. Hexane flow was reduced because of overcrowding of molecules at the pore surface. The effect of confinement diminished with an increase in pore diameter.

42 ENGINEERING↗
DOE OSTI2021

Water-Oil Displacement in Shale: New Insights from a Comparative Study Integrating Imbibition Tests and Multiscale Imaging

Water-oil displacement is an important process that occurs in a shale matrix after hydraulic fracturing and in water-based enhanced oil recovery. Current understanding of this displacement process is limited because of the complicated pore structure and surface properties in shale. In this work, this process and its controlling factors are investigated through a comparative study of three shale samples that have different types of pore systems and wettability. Here, an integrated method of imbibition and multiscale imaging was applied, and a modified oleic tracer that can better represent oil flow was used in imbibition testing and micro-computed tomography (CT) imaging. Scanning electron microscope (SEM) pore characterization was then performed under high magnification with guidance from the micro-CT images showing the changes caused by oil or water imbibition. New insights were obtained on the importance of both wettability and pore size effect on oil recovery and the distribution of residual oil after water-oil displacement. Connectivity of pores with different wettability is also discussed based on 3D analysis and SEM pore characterization. Collectively, these new findings improve the understanding of the complicated process of water-oil displacement and the role of influencing factors. Important implications for improved oil recovery strategy in shale are discussed for different types of reservoir rocks. The integrated imaging and imbibition technique provides a new path for further investigation of improved oil recovery in shale.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2026

How Silica Surface Chemistry Modulates Interfacial Water: Insights from Machine Learning Molecular Dynamics

Controlling water structure and dynamics at silica interfaces are central to a wide range of technologies, including protective oxide layers for solar water splitting and nanoporous membranes. In this work, we develop a machine learning interatomic potential, trained via active learning, to achieve ab initio accuracy for water confined between hydroxylated silica surfaces over a range of silanol coverages and slit widths. We find that partially hydroxylated surfaces (50 and 75% OH) support stronger water−surface hydrogen bonding and more extended interfacial density profiles than fully hydroxylated (100% OH) surfaces, indicating that increasing OH coverage does not necessarily strengthen interfacial hydrogenbond networks. Translational diffusion decreases approximately linearly with slit width and OH coverage, whereas rotational dynamics respond nonlinearly. In particular, at the smallest slit width of 5 Å, 75% OH coverage produces an enhanced local tetrahedral ordered interfacial network that strongly suppresses reorientation, while 100% coverage yields a crowded, disordered interfacial layer that also hinders rotation. In contrast, the 50% OH coverage is sufficiently sparse that it does not markedly alter water structure or dynamics under confinement. These results show that coupled control of pore size and surface chemistry enables nonlinear tuning of interfacial water structure and transport, providing a design strategy for optimizing porous silica for either enhanced interfacial stability and controlled reactivity or rapid and selective transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Molecular insights into the structure-property relationships of 3D printed polyamide reverse-osmosis membrane for desalination

3D-printing is an emerging method for manufacturing polyamide (PA) reserve osmosis (RO) membranes for water treatment and desalination, which can precisely control membrane structural properties, such as thickness, roughness, and resolution. However, the synthesis-structure (i.e., degree of cross-linking (DC), m-phenylenediamine/trimesoyl chloride (MPD/TMC) ratio, and membrane thickness) to property (permeability and water-salt selectivity) relationships for these membranes has not been well understood. At the same time, a microscopic understanding of the physical mechanism of water and salt transport is needed to guide the design of high-performance 3D-printed membranes and improve the printing efficiency. Furthermore, the atomic-scale transport features and energetics of water and salt ions are studied at high pressure for the 3D-printed PA RO membranes with the different DCs and MPD/TMC ratios through non-equilibrium molecular dynamics (NEMD) simulations. Factoring in membrane structure properties, rejection ratio of salt ions and pressure-dependent water flux, 3D-printed PA membranes having an MPD/TMC ratio of 3.0:2.0 and a DC between 80%~90% attains ideal performance: high water flux, high rejection of salt ions, and excellent structural integrity. Mechanistically, water permeability for highly cross-linked PA RO membranes depends on the temporary on-and-off channels that allow water molecules to jump from one cavity to another at high pressure. In addition, higher pressures cause rapid compaction of PA membranes’ free volume and membrane thickness. Membrane failure at high pressure is determined by the DC and MPD/TMC ratios-dependent compressive yield strength. In short, these findings provide physical insights for optimizing existing PA membranes and designing next-generation desalination membranes at the molecular level.

3D-printed PA RO membrane↗
DOE OSTI2023

Controlling Nanoscale Pore Size and Wall Composition in Polycarbonate Membranes via Atomic Layer Deposition and Sequential Infiltration Synthesis: Implications for High Water Permeance

Polymer membranes have a wide variety of applications, ranging from water treatment to energy storage. Many of these applications require precise control over the membrane porosity and surface chemistry. In this study, we explore the modification of isoporous polycarbonate (PC) track-etched membranes (PCTEs) by atomic layer deposition (ALD) and sequential infiltration synthesis (SIS) to tune the pore size and the pore wall surface chemistry. We first performed a detailed study of Al 2 O 3 ALD and SIS in PCTE using a variety of in situ and ex situ measurements. We discovered that short precursor exposure times are critical to achieve conformal Al 2 O 3 ALD in the PCTE nanopores, while longer precursor exposure times resulted in Al 2 O 3 SIS within the bulk of the PC leaving the membranes brittle. Next, we tuned the PCTE pore size via Al 2 O 3 ALD and studied its effect on the water contact angle and the water permeance. Here, we found that the membranes became more hydrophilic, and the permeance decreased with increasing ALD Al 2 O 3 cycles. Finally, we studied the effect of hydrophilic (SnO 2 )/hydrophobic (In 2 O 3 ) ALD metal oxide coatings on membrane properties. We found that the most hydrophilic SnO 2 showed the highest water flux and the least hydrophilic In 2 O 3 showed the lowest water flux through the PCTE membranes. Our results demonstrate that ALD is an effective method to tune the surface and transport properties of PCTE membranes, but care must be exercised to avoid SIS and bulk modification of the polymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Liquid Phase Modeling in Porous Media: Adsorption of Methanol and Ethanol in H-MFI in Condensed Water

Zeolites are used in the chemical and separation industries for their exceptional selectivity, adsorption capacity, regenerability, and stability in gas and liquid phase processing. Here, we developed an explicit solvation method for predicting solvent/condensed phase effects on adsorption free energies in microporous media such as zeolites based on the hybrid quantum mechanical/molecular mechanical free energy perturbation (QM/MM-FEP) technique. Our explicit solvation method for zeolite systems, called eSZS, aims to capture site-specific interactions during the adsorption process at the Brønsted acid sites of H-MFI zeolite while still considering the diverse configuration space of the solvent molecules. This strategy is ideal for chemical reactions or adsorbates that interact with the microporous medium in few distinct adsorbate/transition state configurations, i.e., the harmonic or similar approximations are acceptable for the adsorbate/transition state while such approximations break down for the solvent molecules that require extensive configuration space sampling. In this way, our approach effectively overcomes the limitations of implicit solvation models and classical force field methods for describing solvation effects on chemical reactions within porous materials such as zeolites. Specifically, in this study, we investigated various aspects of our hybrid QM/MM approach, including QM cluster size dependencies in a periodic electrostatically embedded cluster model (PEECM), rules for link atoms at the QM/MM boundary, and functional and basis set considerations for converged and reasonably accurate gas and aqueous phase methanol and ethanol adsorption free energy predictions in H-MFI. For gas phase adsorption of methanol and ethanol in H-MFI at a Brønsted acid site in T12 position, we compute adsorption free energies at 298 K of −0.61 and −0.75 eV, respectively, using a PEECM containing 50 Si and 1 Al atom with ωB97x-D/def2-TZVP level of theory. For solvent effect calculations, we sample the aqueous phase using grand canonical Monte Carlo (GCMC) simulations to (1) obtain a mean field of electrostatic interactions in the reaction system and (2) perform a rigorous free energy perturbation calculation. Similar to the experimentally and computationally observed endergonic solvation effects observed for hydrocarbon adsorption on metal surfaces, we also observe that a condensed aqueous environment destabilizes methanol and ethanol at these acid sites in H-MFI at 298 K. Specifically, the computed solvation free energies of adsorption (ΔΔG solv ) for methanol and ethanol are +0.44 and +0.54 eV, respectively. From this study, it is evident that adsorbates (methanol and ethanol) are competing with water for adsorption space inside the H-MFI zeolite, leading to an endergonic solvation effect. Here, we expect that the endergonic, aqueous solvent effect during adsorption in microporous zeolites is highly tunable by changing the pore size and hydrophobicity of the microporous material as this will affect the water density inside the pore structure.

Adsorption↗
DOE OSTI2022

Relative permeability of gas and water flow in hydrate-bearing porous media: A micro-scale study by lattice Boltzmann simulation

The water-gas relative permeability is an important parameter to characterize multiphase flow in sediments. To study the water-gas relative permeability of hydrate-bearing porous media, multiphase flow simulations were carried out at the pore scale using the lattice Boltzmann method. In this work, the effects of hydrate saturation and hydrate-growth habits on the water-gas relative permeability, which is scaled by the relative permeability considering the hydrate only, were evaluated in a two-dimensional porous medium. Results show that the increase of hydrate saturation causes the decrease of water-gas effective permeability as expected. However, the effect of hydrate saturation on the water-gas relative permeability is different from that of hydrate saturation on the water-gas effective permeability. The water-gas relative permeability increases with the increase of hydrate saturation in the pore-filling case. The water-gas relative permeability decreases with the increase of hydrate saturation in the grain-coating case. The wettability of solid phase has a different effect on the relative permeability of wetting phase and nonwetting phase. The Jamin effect (phase blocking) was observed and may exist in the production of gas from natural gas hydrate reservoirs. This seriously affects the multiphase flow characteristics. The changes of microscale fluid distribution effect the changes of water-gas relative permeability. The relationship between the water-gas relative permeability and the characterization parameters of microscale fluid distribution was analyzed.

58 GEOSCIENCES↗
DOE OSTI2020

Structural Implications of Interfacial Hydrogen Bonding in Hydrated Wyoming-Montmorillonite Clay

Montmorillonite (MMT) clay - a layered porous nanomaterial used as seals in engineered waste containment barriers for spent nuclear fuel - adopts discrete hydration/swelling states depending upon surrounding water and ion activities and confining pressure. The structure of nanoconfined water and charge-balancing counterions in the clay mineral interlayers dictate the swelling and mechanical behavior of MMT, so a molecular model for this clay with high structural fidelity is required to accurately predict the reliability of long-term nuclear waste storage. Here, we present a molecular model for MMT that is based on high resolution transmission electron microscopy of Wyoming-MMT single crystals. Imaging data unambiguously show a cis-vacant arrangement of structural hydroxyl groups in the octahedral sheet, whereas existing molecular models assume a centrosymmetric trans-vacant configuration for MMT. Furthermore, using atomistic simulations, we find that the cis-vacant arrangement of structural hydroxyl groups significantly affects the structure of adsorbed water yielding a larger population of hydrogen bonds with bridging oxygens on the tetrahedral sheet and weak hydrogen bonding between the hydroxyl groups in the octahedral sheet and water in the clay mineral interlayers. As a result, water adsorbed in the interlayer is more "ice-like", with stronger ordering and lower density, although the diffusivity of the interlayer species is not significantly diminished. Our improved structural model for MMT provides insight into the energetics of water adsorption, which ultimately dictates its pore- to macro-scale swelling, transport, and fracture properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Preparing Li-garnet electrodes with engineered structures by phase inversion and high shear compaction processes

We report solid-state lithium batteries are promising for safety and energy density com-pared with traditional lithium-ion batteries. However, the large interfacial resistance between the electrode and electrolyte is a bottleneck to achieving high-performance solid-state batteries. Engineered electrode structures with a porous scaffold of the solid electrolyte material are promising to lower the interfacial resistance and provide a mechanical support for a thin solid electrolyte layer. In this work, two ceramic processing techniques are used to fabricate porous/dense bilayer architectures based on a Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO) Li-garnet material. Finger-like vertically aligned pores are created by the phase inversion (PI) process. A water bath presaturated with Li salt prevents Li loss during the PI solvent exchange step. Pore size and porosity can be optimized by adjusting the bath temperature. The high shear compaction process was used to prepare LLZO tapes with 40, 60, and 80 vol% poreformer. The porosity of the tapes after sintering is 39.5%, 58.4%, and 75.4%, respectively. Microtomography exhibits the porosity, pore shape, and pore distribution of the tapes. A typical cathode material LiNi 0.33 Mn 0.33 Co 0.33 O 2 (NMC) is filled into the pores via vacuum infiltration, and a dense cathode layer is formed within the garnet scaffold.

25 ENERGY STORAGE↗
DOE OSTI2025

Non-Destructive, Three-Dimensional Imaging of Processes in the Rhizosphere Utilizing High Energy Photons

Soil structure, which can be described as the aggregation and distribution of pore spaces, regulates carbon, nutrient, and water cycling across the Earth system. Yet the inability to make quantitative, dynamic, in situ measurements of soil structure and rhizosphere carbon flow has prevented meaningful incorporation of soil structural processes into Earth System Models (ESMs). The key limitations are: (i) Lack of scale integration between micron-scale soil structure and ecosystem-scale models, (ii) Poor functional linkage between soil structural properties and biogeochemical processes, and (iii) Absence of dynamic 3D measurements of rhizosphere structural changes and carbon transformations. To address these challenges, we developed a new integrated positron emission tomography (PET) - microcomputed tomography (CT) imaging platform that enables the first 4D (spatial 3D and time), non-invasive, quantitative imaging of carbon allocation and rhizosphere structural dynamics in living plants and intact soils. The system combines: • Rhizo-PET (R-PET): a high-resolution positron emission tomography scanner optimized for 11 CO 2 tracing in plant roots. • a-Se micro-CT: a high-contrast, high-spatial resolution CT system based on amorphous selenium (a-Se) direct conversion technology, enabling micron-scale visualization of soil structure and root–soil interfaces. Together, these advances allow us to quantify how carbon exudates move, transform, and stabilize within the rhizosphere, directly informing missing processes in BER-relevant carbon cycle models.

42 ENGINEERING↗
DOE OSTI2021

Superhydrophobic coated micro-porous carbon foam membrane and method for solar-thermal driven desalination

A solar membrane distillation apparatus includes a housing comprising a light transmitting wall. A solar distillation membrane is positioned in the housing to receive solar radiation transmitted through the light transmitting wall. The solar distillation membrane includes a porous graphitic foam and a coating of a hydrophobic composition on the surface and pores of the graphitic foam. A water chamber within the housing is provided for retaining water adjacent to the solar distillation membrane. A vapor chamber is provided for collecting water vapor distilling through the solar distillation membrane. A condenser is provided for condensing distilled water vapor from the vapor chamber into liquid water. A separation membrane and a method of solar distillation are also disclosed.

Jang, Gyoung Gug↗
DOE OSTI2025

Interactions of Polar and Nonpolar Groups of Alcohols in Zeolite Pores

Understanding the quantitative interactions among zeolite pore walls, Bro̷nsted acid sites, and molecules with both polar and nonpolar regions is essential for scoping out the potential of zeolites as sorbents and catalysts. Purely siliceous zeolites (MFI and Beta in the present study) are hydrophobic, whereas those containing aluminum are considered hydrophilic, preferentially adsorbing organic molecules even in aqueous environments. To characterize these interactions, we use primary alcohols of increasing molecular weight, quantifying their specific interactions in the confined pore space of the alkyl (CH x ) and OH groups. Three types of interactions were identified: (i) alkyl CH x groups interacting with the zeolite pore walls (approximately 10 kJ mol −1 per carbon), (ii) alcohol OH groups interacting with the pore walls (30−35 kJ mol −1 ), and (iii) alcohol OH groups interacting with Bro̷nsted acid sites (37 kJ mol −1 ). All three interactions were well mirrored by computational simulations. The contribution of the alkyl CH x groups was inferred from the incremental increase in sorption enthalpy with increasing molecular weight; the interaction strength of the OH groups was determined by extrapolating the global adsorption enthalpy of the alcohols to a hypothetical OH group without an alkyl group. This value was identical to the adsorption enthalpy of water. The experiments demonstrated that only water has an adsorption enthalpy on zeolite pore walls lower than its condensation enthalpy (30−35 kJ mol −1 vs 45 kJ mol −1 ), limiting the concentration of water that can be adsorbed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Isolated porosity: A Signature of Submarine Volcanism?

In this conference poster, we show that pumice clasts from submarine volcanoes contain more isolated pores than those from volcanoes that erupt on land. Isolated pores are void spaces that are disconnected from the clast's exterior and are unexpected because most pores coalesce in high total porosity pumice. We specifically, explore the presence of isolated pores in clasts from a 2019 eruption of Volcano F, Tonga and suggest that whole-clast cooling in water may help prevent bubble coalesce and preserve isolated pores. Poster presented at the 2025 International Association of Volcanology and Chemistry of Earth's Interior Meeting (IAVCEI).

flotation↗