An approach to efficient low-speed flight for fan-powered V/STOL aircraft
Ducted cruise fan V/STOL aircraft with efficient low speed flight performance
CRUISE↗
SEARCH · Search NASA
Results for “power flight”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Reliability Block Diagram (RBD) Analysis of NASA Dryden Flight Research Center (DFRC) Flight Termination System and Power Supply
In order to perform public risk analyses for vehicles containing Flight Termination Systems (FTS), it is necessary for the analyst to know the reliability of each of the components of the FTS. These systems are typically divided into two segments; a transmitter system and associated equipment, typically in a ground station or on a support aircraft, and a receiver system and associated equipment on the target vehicle. This analysis attempts to analyze the reliability of the NASA DFRC flight termination system ground transmitter segment for use in the larger risk analysis and to compare the results against two established Department of Defense availability standards for such equipment.
Morehouse, Dennis V.↗
Flight evaluation of augmented controls for approach and landing of powered-lift aircraft
Flight experiments were conducted with Ames Research Center's Quiet Short-Haul Research Aircraft to evaluate the influence of highly augmented control modes on the ability of pilots to execute precision instrument flight operations in the terminal area, particularly approaches to and landings on a short runway. The aircraft is a powered-lift, short-takeoff and landing configuration that is equipped with a modern digital fly-by-wire flight control system, a head-up display, and a solar head-down display that make it possible to investigate control concepts and display format and content for full envelope, powered-lift operations. Considerable attention has been devoted in this flight program to assessing flightpath and airspeed command and stabilization modes developed using nonlinear, inverse model-following methods. The primary benefit of this control concept was realized when the pilot was required to execute a complex transition and approach under instrument conditions and in the presence of a wide range of wind and turbulence conditions.
Franklin, J. A.↗
A compilation of spacecraft loads data from four Titan Centaur launch vehicle flights. Volume 2, part 1: Vibration power spectral density analysis of launch and max Q flight
Summary plots are presented for the time histories and power spectral density analyses of vibration and acceleration on the spacecraft from the Titan Centaur launchings carrying the Viking dynamic simulator and the two Viking spacecraft (TC-1, TC-3 and TC-4).
Kachadourian, G.↗
The value of limited random vibration flight data.
Power and cross spectral density in vector modal terms used to obtain physical interpretation of random behavior of sensitive spacecraft parts
POWER DENSITY↗
Automated Flight & Contingency Management (AFCM) Power Slide
This single slide presentation gives a summary of the Advanced Air Mobility (AAM) Automated Flight & Contingency Management (AFCM) subproject, at a high level for a potentially non-NASA technical audience.
Advanced Air Mobility↗
The Photovoltaic Array Space Power plus Diagnostics (PASP Plus) Flight Experiment
An overview of the Photovoltaic Array Space Power Plus Diagnostics (PASP Plus) flight experiment is presented in outline and graphic form. The goal of the experiment is to test a variety of photovoltaic cell and array technologies under various space environmental conditions. Experiment objectives, flight hardware, experiment control and diagnostic instrumentation, and illuminated thermal vacuum testing are addressed.
Piszczor, Michael F.↗
A new direction in energy conversion - The all-electric aircraft
This paper reviews recent studies of all-electric aircraft that use electric-only secondary power and flight critical fly-by-wire flight controls, and brings to the attention of the power system designer the intrinsic advantages of such aircraft. The all-electric aircraft is made possible by the development of rare earth magnet materials and fault tolerant systems technologies. Recent studies have shown all-electric aircraft to be more efficient than conventional designs and offer substantial operating costs reductions. Compared to present aircraft, an all-electric transport can save at least 10 percent in fuel burn. The cornerstone of an all-electric aircraft is the electric secondary power system. This paper reviews the major features of flight critical electric secondary power systems. Research required to lay the foundation for an all-electric aircraft is briefly discussed.
Spitzer, C. R.↗
Low power DIPS design for NASA missions
Conceptual designs of low power dynamic isotope power systems (DIPS) for NASA's future deep space missions are being developed to characterize the power system's unique features in the 0.5-1.0 kilowatt-electric (kWe) range. The August 1990 Mariner Mark II spacecraft design was used for the spacecraft integration study. One basic design with slight mission specific variations was developed for the Cassini, Comet Nucleus Sample Return, and Outer Planet Orbiter Probe missions. A low power DIPS flight unit offers comparable specific power values to the MOD-RTG unit with a factor-of-three improvement in radioisotope fuel requirements. This was accomplished by fully exploiting the dynamic power conversion technology available in the DIPS program.
Johnson, Richard A.↗
Deep Space Systems Technology Program Future Deliveries
NASA is in a period of frequent launches of low cost deep space missions with challenging performance needs. The modest budgets of these missions make it impossible for each to develop its own technology, therefore, efficient and effective development and insertion of technology for these missions must be approached at a higher level than has been done in the past. The Deep Space Systems Technology Program (DSST), often referred to as X2000, has been formed to address this need. The program is divided into a series of "Deliveries" that develop and demonstrate a set of spacecraft system capabilities with broad applicability for use by multiple missions. The First Delivery Project, to be completed in 2001, will provide a one MRAD-tolerant flight computer, power switching electronics, efficient radioisotope power source, and a transponder with services at 8.4 GHz and 32 GHz bands. Plans call for a Second Delivery in late 2003 to enable complete deep space systems in the 10 to 50 kg class, and a Third Delivery built around Systems on a Chip (extreme levels of electronic and microsystems integration) around 2006. Formulation of Future Deliveries (past the First Delivery) is ongoing and includes plans for such developments as highly miniaturized digital/analog/power electronics, optical communications, multifunctional structures, miniature lightweight propulsion, advanced thermal control techniques, highly efficient radioisotope power sources, and a unified flight ground software architecture to support the needs of future highly intelligent space systems. All developments are targeted at broad applicability and reuse, and will be commercialized within the US.
Salvo, Christopher G.↗
Low-Speed Flight Characteristics of a Powered-Lift Jet Transport During the Landing Approach
A flight-test program to determine the flight characteristics of large jet transports equipped with powered-lift systems indicated the following results: Speed margins appear to be primarily related to power-on stall speeds. At these speed margins, the maneuver margins were adequate and did not appear to be a problem or limiting factor during powered-lift operation. No large detrimental effects on handling qualities were apparent but in some areas stability augmentation would be required to obtain satisfactory flight characteristics. Use of the powered-lift airplane would result in a sizable increase in the noise levels; these increases are primarily the result of higher engine power settings in the approach.
Schade, Robert O.↗
Closed loop performance of a brushless dc motor powered electromechanical actuator for flight control applications
A comprehensive digital model for the analysis and possible optimization of the closed loop dynamic (instantaneous) performance of a power conditioner fed, brushless dc motor powered, electromechanical actuator system (EMA) is presented. This model was developed for the simulation of the dynamic performance of an actual prototype EMA built for NASA-JSC as a possible alternative to hydraulic actuators for consideration in Space Shuttle Orbiter applications. Excellent correlation was achieved between numerical model simulation and experimental test results obtained from the actual hardware. These results include: various current and voltage waveforms in the machine-power conditioner (MPC) unit, flap position as well as other control loop variables in response to step commands of change of flap position. These results with consequent conclusions are detailed in the paper.
Demerdash, N. A.↗
Flight Tests of Rocket-Powered "Tin-Can" Models of AAF Project MX-800
Flight tests were made of six noninstrumented rocket-powered "Tin Can" models of AAF Project MX-800. Velocity and drag data were obtained by use of CU Doppler radar. The existence of stability and adequate structural strength for flight near zero lift was checked by visual and photographic observation. Drag data obtained during the tests agreed reasonably well with estimates based on experimental data from NACA RM-2 rocket-powered drag research models.
Purser, Paul E.↗
An Exploratory Study of Thermoelectrostatic Power Generation for Space Flight Applications
A study has been made of a process in which a solar heating cycle is combined with an electrostatic cycle for generating electrical power for space vehicle applications. The power unit, referred to as a thermoelectrostatic generator, is a thin film, solid dielectric capacitor alternately heated by solar radiation and cooled by radiant emission. The theory of operation to extract electrical power is presented. Results of an experiment to illustrate the principle are described. Estimates of the performance of this type of device in space in the vicinity of earth are included. Values of specific power of several kilowatts per kilogram of generator weight are calculated for such a device employing polyethylene terephthalate dielectric.
Beam, Benjamin H.↗
Users guide for guidance and control Launch and Abort Simulation for Spacecraft (LASS), volume 1
The mathematical models and computer program which are used to implement LASS are described. The computer program provides for a simulation of boost to orbit and abort capability from boost trajectories to a prescribed target. The abort target provides a decision point for engine shutdown from which the vehicle coasts to the vicinity of the selected abort recovery site. The simulation is a six degree of freedom simulation describing a rigid body. The vehicle is influenced by forces and moments from nondistributed aerodynamics. An adaptive autopilot is provided to control vehicle attitudes during powered and unpowered flight. A conventional autopilot is provided for study of vehicle during powered flight.
Havig, T. F.↗
Simulation of a Miniature, Low-Power Time-of-Flight Mass Spectrometer for In Situ Analysis of Planetary Atmospheres
We are implementing nano- and micro-technologies to develop a miniaturized electron impact ionization mass spectrometer for planetary science. Microfabrication technology is used to fabricate the ion and electron optics, and a carbon nanotube (CNT) cathode is used to generate the ionizing electron beam. Future NASA planetary science missions demand miniaturized, low power mass spectrometers that exhibit high resolution and sensitivity to search for evidence of past and present habitability on the surface and in the atmosphere of priority targets such as Mars, Titan, Enceladus, Venus, Europa, and short-period comets. Toward this objective, we are developing a miniature, high resolution reflectron time-of-flight mass spectrometer (Mini TOF-MS) that features a low-power CNT field emission electron impact ionization source and microfabricated ion optics and reflectron mass analyzer in a parallel-plate geometry that is scalable. Charged particle electrodynamic modeling (SIMION 8.0.4) is employed to guide the iterative design of electron and ion optic components and to characterize the overall performance of the Mini TOF-MS device via simulation. Miniature (less than 1000 cubic centimeters) TOF-MS designs (ion source, mass analyzer, detector only) demonstrate simulated mass resolutions greater than 600 at sensitivity levels on the order of 10(exp -3) cps/molecule N2/cc while consuming 1.3 W of power and are comparable to current spaceflight mass spectrometers. Higher performance designs have also been simulated and indicate mass resolutions approximately 1000, though at the expense of sensitivity and instrument volume.
King, Todd T.↗
Arcjet thruster research and technology. Phase 1: Executive summary
The principal objective of this two phase program is to conduct the development research required to make the low power arcjet a flight ready technology. Many important results were obtained during Phase 1 to move closer to this objective. Fundamental analyses were performed of the arcjet nozzle, the gas kinetic reaction effects, the thermal environment, and the arc stabilizing vortex. These aided the conceptual understanding of the arcjet and guided design work. A hydrazine (N2H4) arcjet was designed that combined a flight qualified catalyst bed with a modular arcjet. Extensive testing was performed which demonstrated the feasibility of using this propellant in an arcjet for the first time. Startup techniques were developed, stability maintained, material compatibility tests conducted, and performance mapping tests performed. Specific impulse values from 400 to 730 seconds were produced with a non-optimized design. These levels are higher than were originally thought possible and proved that extremely high enthalpy values can be obtained with constricted arc technology. Erosion rate data are promising for lifetime extensions to meet flight application requirements. Power control unit (PCU) development was started with the design and fabrication of a laboratory high switching frequency supply. Valuable data were obtained on PCU operation and on the interaction with the dynamic arc. Phase 2 efforts presently underway are resolving key issues for multi-hundred hour lifetimes, are continuing to investigate arcjet/PCU interactions, and will demonstrate duty cycle N2H4 arcjet/PCU operation in a simulated flight mode for lifetimes consistent with initial applications.
Source record↗
X-43A: The First Flight of a Scramjet Powered Airplane
A viewgraph presentation describing the X-43A Scramjet engine is shown. The topics include: 1) Scramjets; 2) Overview of X-43A; 3) What Happened the 1st Time; 4) Return to Flight; and 5) What Happened the 2nd Time.
Corpening, Griff↗