Search NASA⌕ Search

SEARCH · Search NASA

Results for “simultaneous operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

NASA Engineering and Safety Center Technical Bulletin No. 10-02: Potential Failure of Dual Simultaneously Initiated Pyrotechnic Operated Valves

The NASA Engineering and Safety Center (NESC) Technical Bulletin No. 09-01 reported an independent investigation of four pyrovalve failures that occurred while using aluminum (Al) pyrovalve primer chamber assemblies (PCAs) during ground testing. The investigation revealed that simultaneous firing (within a few microseconds) of the NASA Standard Initiators (NSIs) was the primary reason why the booster charge failed to ignite and the pyrovalves subsequently failed to operate. A second investigation of a new stainless steel (SS) PCA design with separate flame channels was completed in 2010. The new SS configuration was found to be improved in most respects; however, no improvement was noted in the temperature delivered to ignite the booster during dual simultaneous NSI firings. Simultaneous firings should be avoided when using either the Al or the SS PCA design.

Potential Failure↗
NASA NTRS1997

Applied Virtual Reality in Reusable Launch Vehicle Design, Operations Development, and Training

Application of Virtual Reality (VR) technology offers much promise to enhance and accelerate the development of Reusable Launch Vehicle (RLV) infrastructure and operations while simultaneously reducing developmental and operational costs. One of the primary cost areas in the RLV concept that is receiving special attention is maintenance and refurbishment operations. To produce and operate a cost effective RLV, turnaround cost must be minimized. Designing for maintainability is a necessary requirement in developing RLVs. VR can provide cost effective methods to design and evaluate components and systems for maintenance and refurbishment operations. The National Aeronautics and Space Administration (NASA)/Marshall Space Flight Center (MSFC) is beginning to utilize VR for design, operations development, and design analysis for RLVs. A VR applications program has been under development at NASA/MSFC since 1989. The objectives of the MSFC VR Applications Program are to develop, assess, validate, and utilize VR in hardware development, operations development and support, mission operations training and science training. The NASA/MSFC VR capability has also been utilized in several applications. These include: 1) the assessment of the design of the late Space Station Freedom Payload Control Area (PCA), the control room from which onboard payload operations are managed; 2) a viewing analysis of the Tethered Satellite System's (TSS) "end-of-reel" tether marking options; 3) development of a virtual mockup of the International Space Welding Experiment for science viewing analyses from the Shuttle Remote Manipulator System elbow camera and as a trainer for ground controllers; and 4) teleoperations using VR. This presentation will give a general overview of the MSFC VR Applications Program and describe the use of VR in design analyses, operations development, and training for RLVs.

Hale, Joseph P.↗
NASA NTRS1988

Technique to select the optimum modulation indices for suppression of undesired signals for simultaneous range and data operations

An algorithm to search for the optimum set of modulation indices that will optimize a given simultaneous range/command/telemetry communications link is presented. This technique provides a way to suppress the ranging signal in order to limit performance degradation in the data channel due to interference from the ranging channel to a desired level, given a specified ranging accuracy. The link (when optimized) will (1) provide maximum available power to both the data and ranging channels for a specified degradation in the data channel so that it will transmit at the required data rate, (2) achieve a specified ranging accuracy over a maximum distance, under a certain set of conditions, and (3) provide adequate power for carrier tracking without degrading the data-channel thresholds. In addition, both data and ranging channels will fall below the threshold at the same point.

Nguyen, Tien Manh↗
NASA NTRS2002

Potential Operating Orbits for Fission Electric Propulsion Systems Driven by the SAFE-400

Safety must be ensured during all phases of space fission system design, development, fabrication, launch, operation, and shutdown. One potential space fission system application is fission electric propulsion (FEP), in which fission energy is converted into electricity and used to power high efficiency (Isp greater than 3000s) electric thrusters. For these types of systems it is important to determine which operational scenarios ensure safety while allowing maximum mission performance and flexibility. Space fission systems are essentially nonradioactive at launch, prior to extended operation at high power. Once high power operation begins, system radiological inventory steadily increases as fission products build up. For a given fission product isotope, the maximum radiological inventory is typically achieved once the system has operated for a length of time equivalent to several half-lives. After that time, the isotope decays at the same rate it is produced, and no further inventory builds in. For an FEP mission beginning in Earth orbit, altitude and orbital lifetime increase as the propulsion system operates. Two simultaneous effects of fission propulsion system operation are thus (1) increasing fission product inventory and (2) increasing orbital lifetime. Phrased differently, as fission products build up, more time is required for the fission products to naturally convert back into non-radioactive isotopes. Simultaneously, as fission products build up, orbital lifetime increases, providing more time for the fission products to naturally convert back into non-radioactive isotopes. Operational constraints required to ensure safety can thus be quantified.

Houts, Mike↗
NASA NTRS2002

Potential Operating Orbits for the SAFE-400

Safety must be ensured during all phases of space fission system design, development, fabrication, launch, operation, and shutdown. One potential space fission system application is fission electric propulsion (FEP), in which fission energy is converted into electricity and used to power high efficiency (Isp is greater than 3000s) electric thrusters. For these types of systems it is important to determine which operational scenarios ensure safety while allowing maximum mission performance and flexibility. Space fission systems are essentially non-radioactive at launch, prior to extended operation at high power. Once high power operation begins, system radiological inventory steadily increases as fission products build up. For a given fission product isotope, the maximum radiological inventory is typically achieved once the system has operated for a length of time equivalent to several half-lives. After that time, the isotope decays at the same rate it is produced, and no further inventory builds in. For an FEP mission beginning in Earth orbit, altitude and orbital lifetime increase as the propulsion system operates. Two simultaneous effects of fission propulsion system operation are thus (1) increasing fission product inventory and (2) increasing orbital lifetime. Phrased differently, as fission products build up, more time is required for the fission products to naturally convert back into non-radioactive isotopes. Simultaneously, as fission products build up, orbital lifetime increases, providing more time for the fission products to naturally convert back into non-radioactive isotopes. Operational constraints required to ensure safety can thus be quantified.

Houts, Mike↗
NASA NTRS2005

PCM Passive Cooling System Containing Active Subsystems

A multistage system has been proposed for cooling a circulating fluid that is subject to intermittent intense heating. The system would be both flexible and redundant in that it could operate in a basic passive mode, either sequentially or simultaneously with operation of a first, active cooling subsystem, and either sequentially or simultaneously with a second cooling subsystem that could be active, passive, or a combination of both. This flexibility and redundancy, in combination with the passive nature of at least one of the modes of operation, would make the system more reliable, relative to a conventional cooling system. The system would include a tube-in-shell heat exchanger, within which the space between the tubes would be filled with a phase-change material (PCM). The circulating hot fluid would flow along the tubes in the heat exchanger. In the basic passive mode of operation, heat would be conducted from the hot fluid into the PCM, wherein the heat would be stored temporarily by virtue of the phase change.

Blanding, David E.↗
NASA NTRS2021

Extending the Licklider Transmission Protocol to Multi-Band Links

Most deep space missions return data to Earth using links operating at a single frequency band. Indeed, their data requirements are low enough that bandwidth regulations do not constrain the system. In contrast, spacecraft such as Kepler or Europa Clipper are transitioning to a new operational paradigm where engineering and science data are transmitted through simultaneous links operating at different frequency bands (henceforth termed multi-band links). This ensures, for instance, that critical data is correctly received using a well characterized X-band link, while science data at a much larger data rate can be returned efficiently (both in terms of bandwidth and energy) through a Ka-band link.Having a spacecraft establish two simultaneous links with a ground station opens a large span of potential improvements for space communications and mission operations. In this paper, we consider the problem of running a Licklider Transmission Protocol (LTP) session over a multi-band link. LTP is an implementation of a selective Automatic Repeat reQuest (ARQ) protocol, i.e. it ensures correct delivery of data over an error prone link with potentially long propagation delays. To maximize its efficiency in deep space environments, LTP operates in deferred-ACK mode and is typically included as one of the core protocols in the Delay Tolerant Networking (DTN) suite.The contributions of this paper are as follows: First, we propose an extension to LTP for multi-band links (denoted MBLTP) and sketch how it can be implemented without modifying the current definition of LTP data units. Next, we develop bounds on the performance of MBLTP when transmitting a single data file over a multi-band link. Three metrics are considered, file expected delivery time, total energy spent and bundle jitter. The results of the analytic model are first benchmarked against simulations to ensure validity, and then compared against the performance of both traditional LTP and Parallel LTP (PLTP).We demonstrate that MBLTP can significantly reduce the latency and jitter with which data products are delivered to destination over a deep space link compared to LTP at moderate energy cost. Similarly, we also demonstrate that MBLTP outperforms PLTP in all considered metrics.

Sanchez Net, Marc↗
NASA NTRS2006

Flow and Noise Control in High Speed and High Reynolds Number Jets Using Plasma Actuators

The idea of manipulating flow to change its characteristics is over a century old. Manipulating instabilities of a jet to increase its mixing and to reduce its radiated noise started in the 1970s. While the effort has been successful in low-speed and low Reynolds number jets, available actuators capabilities in terms of their amplitude, bandwidth, and phasing have fallen short in control of high-speed and high Reynolds number jets of practical interest. Localized arc filament plasma actuators have recently been developed and extensively used at Gas Dynamics and Turbulence Laboratory (GDTL) for control of highspeed and high Reynolds number jets. While the technique has been quite successful and is very promising, all the work up to this point had been carried out using small high subsonic and low supersonic jets from a 2.54 cm diameter nozzle exit with a Reynolds number of about a million. The preliminary work reported in this paper is a first attempt to evaluate the scalability of the technique. The power supply/plasma generator was designed and built in-house at GDTL to operate 8 actuators simultaneously over a large frequency range (0 to 200 kHz) with independent control over phase and duty cycle of each actuator. This allowed forcing the small jet at GDTL with azimuthal modes m = 0, 1, 2, 3, plus or minus 1, plus or minus 2, and plus or minus 4 over a large range of frequencies. This power supply was taken to and used, with minor modifications, at the NASA Nozzle Acoustic Test Rig (NATR). At NATR, 32 actuators were distributed around the 7.5 in. nozzle (a linear increase with nozzle exit diameter would require 60 actuators). With this arrangement only 8 actuators could operate simultaneously, thus limiting the forcing of the jet at NATR to only three azimuthal modes m = plus or minus 1, 4, and 8. Very preliminary results at NATR indicate that the trends observed in the larger NASA facility in terms of the effects of actuation frequency and azimuthal modes are similar in both small GDTL and larger NASA jets. However, the actuation authority seems to fall short in the larger jet at higher Mach numbers, resulting in decreased amplitude response compared to the small jet, which is attributed at this point to the lack of sufficient number of actuators. The preliminary results seem also to suggest that amplitude of actuation tones is similar in both the small and larger jets.

Samimy, M.↗
NASA NTRS1974

Optical properties of mercury ion thruster exhausts and implications for science instruments

Emission from the exhaust plume of a 30 cm mercury ion thruster was measured from 160 to 600 nm as a function of axial and radial distance from the thruster discharge chamber. The spectrally dispersed absolute intensities were used to construct an empirical volume rate function. The function was integrated along a typical instrument field of view, and the resulting apparent brightness was compared with instrument sensitivities to evaluate the extent of optical interference. Most of the emitted radiation came from UV lines of excited mercury atoms and ions, with no observable continuum emission. The intensity levels degraded rapidly with distance from the thruster so that optical interference was negligible for fields of view not intercepting the beam axis. The operation of only one instrument, a zodiacal photopolarimeter, was considered incompatible with simultaneous thruster operation.

Monahan, K. M.↗
NASA NTRS1975

Optical properties of mercury ion thruster exhaust plumes Significance for candidate SEP science instruments

Emission from the exhaust plume of a 30 cm mercury ion thruster was measured from 160 to 600 nm as a function of axial and radial distance from the thruster discharge chamber. The spectrally dispersed absolute intensities were used to construct an empirical volume emission rate function. The function was integrated along a typical instrument field of view, and the resulting apparent brightness was compared with instrument sensitivities to evaluate the extent of optical interference. The intensity levels degraded rapidly with distance from the thruster so that optical interference was negligible for fields of view not intercepting the beam axis. The operation of only one instrument, a zodiacal photopolarimeter was considered incompatible with simultaneous thruster operation.

Goldstein, R.↗
NASA NTRS1985

Increased productivity in flight with voice commanding

Automatic Speech Recognition technology has matured to the point where it can provide a viable means of increasing productivity by naturalizing the man-machine interface. With ever increasing workloads being placed on astronauts, speech recognition may provide an alternative means of system controlling that would reduce the task burden. Voice commanding, allowing hands-free operation, can be especially effective during operations requiring simultaneous system control. A flight experiment is under development to demonstrate the operational effectiveness of voice control by commanding the Space Shuttle's Closed Circuit Television (CCIV) system. This experiment will help direct future applications of voice entry to space operations.

Jordan, W. T.↗
NASA NTRS1996

X/X/Ka-Band Horn Design

Tne NASA's Deep Space Network has a need for a multi frequency horn for simultaneous X/X/Ka-band operation in a beam waveguide antenna. The multi frequency horn will receive X-band downlink (8.4-8.5 GHz) and Ka-band downlink (3.18-32.3 GHz), and transmit X-band uplink (7.145-7.235 GHz) signals simultaneously. The horn is designed for circularlly polarized wave operation. Low loss (noise) and high power (up to 20 kilowatts) operation are considered in the horn design.

Deep Space Network beam waveguide antenna multi fr↗
NASA NTRS2017

Spectral and Radiometric Calibration Using Tunable Lasers

A tunable laser system includes a tunable laser, an adjustable laser cavity for producing one or more modes of laser light emitted from the tunable laser, a first optical parametric oscillator positioned in a light path of the adjustable laser cavity, and a controller operable to simultaneously control parameters of at least the tunable laser, the first optical parametric oscillator, and the adjustable laser cavity to produce a range of wavelengths emitted from the tunable laser system. A method of operating a tunable laser system includes using a controller to simultaneously control parameters of a tunable laser, an adjustable laser cavity for producing one or more modes of laser light emitted from the tunable laser, and a first optical parametric oscillator positioned in a light path of the adjustable laser cavity, to produce a range of wavelengths emitted from the tunable laser system.

McCorkel, Joel↗
NASA NTRS2010

Lunar Surface Operations with Dual Rovers

Lunar Electric Rovers (LER) are currently being developed that are substantially more capable than the Apollo vehicle (LRN ,"). Unlike the LRV, the new LERs provide a pressurized cabin that serves as short-sleeve environment for the crew of two, including sleeping accommodations and other provisions that allow for long tern stays, possibly up to 60 days, on the hear surface, without the need to replenish consumables from some outside source, such as a lander or outpost. As a consequence, significantly larger regions may be explored in the future and traverse distances may be measured in a few hundred kilometers (1, 2). However, crew safety remains an overriding concern, and methods other than "walk back", the major operational constraint of all Apollo traverses, must be implemented to assure -at any time- the safe return of the crew to the lander or outpost. This then causes current Constellation plans to envision long-tern traverses to be conducted with 2 LERs exclusively, each carrying a crew of two: in case one rover fails, the other will rescue the stranded crew and return all 4 astronauts in a single LER to base camp. Recent Desert Research and Technology Studies (DRATS) analog field tests simulated a continuous 14 day traverse (3), covering some 135 km, and included a rescue operation that transferred the crew and diverse consumables from one LER to another these successful tests add substantial realism to the development of long-term, dual rover operations. The simultaneous utilization of 2 LERs is of course totally unlike Apollo and raises interesting issues regarding science productivity and mission operations, the thrust of this note.

Horz, Friedrich↗
NASA NTRS2022

Test Facilities for SHERLOC Laser Development

The Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) instrument is a deep UV laser based spectrometer that is part of NASA’s Mars Perseverance rover. The laser is a pulsed 248.6 nm NeCu hollow cathode gas discharge laser. The design, development, and testing of lasers and laser power supplies (LPS) were performed by scientists and engineers at the Jet Propulsion Laboratory (JPL) and Photon Systems Inc. (PSI). While these lasers had been used previously in extreme terrestrial environments, before they had to be qualified for operation and functionality over the expected range of environmental situations (temperature cycling, vibration, mechanical shock, low pressure corona emission testing) over the course of mission life time. The SHERLOC laser/LPS testing facilities consisted of custom-tailored environmental test chambers with metrology/control electronics. A custom LabVIEW software package was developed to autonomously operate all test facilities using a multi-threaded, object-oriented programming architecture, tasked with interfacing with many instruments simultaneously for operation and data acquisition.

Houck, Andrew↗
NASA NTRS2023

Safety Case for Small Uncrewed Aircraft Systems (sUAS) Beyond Visual Line of Sight (BVLOS) Operations at NASA Langley Research Center

This Technical Memorandum (TM) is written to provide for dissemination of the methods and safety considerations for operations of small Uncrewed Aerial Systems (sUAS) Beyond Visual Line-of-Sight (BVLOS)at NASA Langley Research Center. It includes the Safety Case used to acquire a BVLOS Certificate of Authorization (COA) from the FAA and is being published to enable others to benefit from this work. The intended operations, subject to approval from the Federal Aviation Administration (FAA) and the National Aeronautics and Space Administration (NASA), will include a combination of Within Visual Line of Sight (WVLOS) and Beyond Visual Line of Sight (BVLOS) flights, comprising of at most five sUAS operating concurrently, with no more than three operating BVLOS. Flights will occur in a subset of the Langley Air Force Base (LAFB) Class D airspace (KLFI) at a maximum altitude of 400 ft AGL. Most operations within this subset will take place in the City Environment Range Testing for Autonomous Integrated Navigation (CERTAIN) Range. The CERTAIN Range includes airspace inside the borders of NASA Langley Research Center (LaRC). Additional airspace over the northern section of CERTAIN will be requested as part of the Certificate of Authorization (COA). NASA LaRC BVLOS operations on the CERTAIN Range can be broken down into five critical components needed to meet the 14 CFR § 91.113 see and avoid requirement: 1) procedural deconfliction with LAFB for UAS operations at or below 400 ft and manned aircraft at or above 900’ AGL; 2) ground equipment for detection of intruder aircraft and to support communications between crewmembers ; 3) sUAS vehicles with advanced onboard automation capable of autonomously maintaining safe separation; 4) BVLOS standardized operating procedures (SOPs); 5) and personnel to execute the flight operations in accordance with the SOPs and respond to airborne contingencies. The introduction of new ground equipment includes the use of the Remote Operations for Autonomous Missions (ROAM) UAS Operations Center, development and use of an Integrated Airspace Display (IAD), use of the L-STAR and GA-9120 radars, and the incorporation of standardized Vertiports. The ROAM Operations Center will be the central point for all BVLOS sUAS operations. All command and control (C2), voice communications and airspace awareness displays will reside inside ROAM. The IAD will provide raw data from ADS-B, FLARM, radar tracks and telemetered GPS vehicle positions for interpretation by an Airspace Monitor. The radars will search the class D airspace around the CERTAIN Range and serve as a backup to procedural deconfliction procedures coordinated with LAFB. In the event of a procedural deconfliction breakdown, radar detections of non-participating aircraft will be available so that the 91.113 see and avoid requirement can still be safely met. Finally, the incorporation of Vertiports will have video and network connectivity that enables large numbers of sUAS launches and recoveries from a single location. This is a continuation of the remote command and control of unpiloted aircraft component focused on evaluating unpiloted aircraft flight crew roles and responsibilities, control interfaces and the associated data links needed to operate a fleet of aircraft within a UAM Ecosystem. This work supports the development of future aviation operational concepts based on an Urban Air Mobility Maturity Level (UML) 4 environment (Patterson, 2020). It is assumed that future airspace will include hundreds of simultaneous aircraft operations within the airspace, therefore scalable operations are essential for enabling this future airspace to become a reality. Follow on work includes envisioned flights that expand operations beyond the CERTAIN range and lead to an effective Maritime Surveillance capability.

Matthew W Coldsnow↗