Search NASA⌕ Search

SEARCH · Search NASA

Results for “software differences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Equivalent-Circuit Models of Grid-Forming IBRs for Electromagnetic-Transient Simulations

We derive equivalent-circuit models of control- and physical-layer subsystems of grid-forming (GFM) inverter-based resources (IBRs) for electromagnetic-transient (EMT) simulations. Three different primary controllers are considered: Droop, Virtual Synchronous Machine (VSM), and dispatchable Virtual Oscillator Control (dVOC). In addition, the models include cascaded voltage- and current-control loops, and LCL output filters. Simulations for a single-inverter setup and for a network of five inverters in a modified IEEE 14-bus topology are presented. The equivalent-circuit models simulated with analog electronic circuit-simulator software (in our case, LTspice) offer the same accuracy, and with no explicit tuning of the solver, lower computational burden compared to block-diagram-based implementations in commercial off-the-shelf EMT software (in our case, MATLAB-Simulink).

electromagnetic transient simulation↗
DOE OSTI2025

WHA Sphere Impacting RHA Plate: Modeling Brittle Behavior in Metal Alloys

Brittle behavior of metal alloys is often critical to modeling ballistic impact and penetration. The ALEGRA multiphysics finite element software incorporates calibrated models for the equation of state, elasticity, yield stress, plasticity and fracture, but simulations do not always capture expected metal fracture. Here we report concerted efforts to do so for one important case where experiments clearly show shear fractures: a tungsten sphere impacting a steel plate at various angles. Our best simulations show fractures that are qualitatively similar to experiments, but there are significant differences in quantitative metrics. Specifically, velocities of tracers used to quantify simulated plug parameters consistently fall short of measured plug velocities. Also, simulated plugs break apart more than expected from experimental evidence. We attribute these shortfalls to the lack of an explicit shear fracture mechanism in the material models, leading to over-estimated resistance to plug formation and movement.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Equivalent-Circuit Models of Grid-Forming IBRs for Electromagnetic-Transient Simulations: Preprint

We derive equivalent-circuit models of control- and physical-layer subsystems of grid-forming (GFM) inverter-based resources (IBRs) for electromagnetic-transient (EMT) simulations. Three different primary controllers are considered: droop, virtual synchronous machine (VSM), and dispatchable virtual oscillator control (dVOC). In addition, the models include cascaded voltage- and current-control loops, and LCL output filters. Simulations for a single-inverter setup and for a network of five inverters in a modified IEEE 14-bus topology are presented. The equivalent-circuit models simulated with analog electronic circuit-simulator software (in our case, LTspice) offer the same accuracy with up to 150x lower computational burden compared to block-diagram-based implementations in commercial off-the-shelf EMT software (in our case, MATLAB-Simulink).

circuit-equivalent model↗
DOE OSTI2024

Computing within the 2021 Snowmass process

We present different elements of the 2021–2022 Computational Frontier (CompF) effort within the Snowmass process, including organization, events, and highlights of the final report. With focus in the next 10–15 years, we analyze the impact of newly established and emerging technologies, identify challenges within theoretical, experimental and observational research programs, and present the report recommendations. We emphasize the main recommendation, which is the formation of a Coordinating Panel for Software and Computing (CPSC).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Medium Voltage Testbed for Comparing Advanced Power Line Sensors vs. Transformers with Electrical Grid Events

Electrical utilities have relied upon potential transformers (PTs) and current transformers (CTs) for very accurate metering and to provide reliable signals for protective relays. These devices measure phase voltages and currents and are commissioned by electrical engineers. PTs/CTs can detect and react to various electrical anomalies that could adversely affect electrical grid operations. Less expensive alternative sensing technologies offer the possibility of wider deployment, particularly in grids that employ distributed energy resources. In this work, the performance of an advanced medium-voltage sensor is compared with that of a reference PT and a CT and experimentally evaluated for different power grid scenarios on an advanced outdoor power line sensor testbed at the U.S. Department of Energy’s Oak Ridge National Laboratory. The sensor is based on a capacitive divider for voltage monitoring and a Rogowski coil with an integrator for current monitoring. This study simulated a power grid model based on a utility circuit at the Riverside EPB of Chattanooga. The simulation circuit was created with MATLAB/Simulink software and was integrated into an RT-LAB project to run with the OP4510 real-time simulator at the OPLST. During the tests, the real-time simulations were run for 40 s, and the signal to record the test event with the power meter was set at 30 s for the event-trigger circuit. The advanced outdoor power line sensor testbed has a real-time simulator that is used to generate transient scenarios (e.g., electrical faults, capacitor bank operation, and service restoration), while the analog signals are recorded by the same high-resolution power meter. The behaviors of analog signals, harmonic components, total harmonic distortion, and crest factors are assessed for this power line sensor and compared with those of the reference PT/CT because of the absence of testing standards for advanced outdoor power line sensors. The results showed that this OPLS technology responded identically to the PT and CT under all conditions.

Piesciorovsky, Emilio [ORNL]↗
DOE OSTI2025

Determining Levels of Detail for Simulators of Parallel and Distributed Computing Systems via Automated Calibration

There are two sources of inaccuracy when simulating parallel and distributed computing systems: (i) a simulator implemented at an insufficient level of detail; and (ii) incorrectly calibrated simulation parameter values. Increasing the simulator’s level of detail can improve accuracy, but at the cost of higher space, time, and/or software complexity. Furthermore, evaluating the intrinsic accuracy of a simulator requires that its parameters be well-calibrated. Making decisions regarding the level of detail is thus challenging. We propose a methodology for instantiating the simulation calibration process and a framework for automating this process, which makes it possible to pick appropriate levels of detail for any simulator. We demonstrate the usefulness of our approach via two case studies for two different domains.

McDonald, Jessie [University of Hawaii at Manoa, H↗
DOE OSTI2025

ITreeForeCast: An integrated modeling software to simulate tree level growth and forest carbon storage

Healthy trees in forest act as a natural carbon sink, capturing carbon. As they grow, they store carbon in their trunks, leaves and roots. Not all trees store carbon at the same rate, or in the same quantities, as it depends on a variety of biophysical and climatic factors. Furthermore, although carbon estimation in trees can be complex, the precision of estimates is tightly linked to trees growth, both in diameter and height. However, the simulation of carbon uptake by forest and forest growth has each been modeled separately, and independently at differing levels of detail and spatial resolution. In this paper, we introduce ITreeForeCast, a simulation model combining the two types of modeling on a unified platform, enabling the investigation of impacts of management strategies on carbon sequestration and wood products. ITreeForeCast is a user-extendable framework that offers new opportunities to model, simulate, and visualize the dynamics of individual trees in a forest, simulate management strategies over time, and carbon uptake.

09 - BIOMASS FUELS↗
DOE OSTI2024

The Impact of Void-finding Algorithms on Galaxy Classification

We explore how the definition of a void influences the conclusions drawn about the impact of the void environment on galactic properties using two void-finding algorithms in the Void Analysis Software Toolkit: Voronoi Voids (V 2 ), a Python implementation of ZOnes Bordering On Voidness (ZOBOV); and VoidFinder, an algorithm that grows and merges spherical void regions. Using the Sloan Digital Sky Survey Data Release 7, we find that galaxies found in VoidFinder voids tend to be bluer and fainter and to have higher (specific) star formation rates than galaxies in denser regions. Conversely, galaxies found in V 2 voids show less significant differences when compared to galaxies in denser regions, less consistent with the large-scale environmental effects on galaxy properties expected from both simulations and previous observations. These results align with previous simulation results that show V 2 -identified voids “leak” into the dense walls between voids because their boundaries extend up to the density maxima in the walls. As a result, when using ZOBOV-based void-finders, galaxies likely to be part of wall regions are instead classified as void galaxies, a misclassification that can be critical to our understanding of galaxy evolution.

cosmic web↗
DOE OSTI2025

CT Scans of Cores Metadata, Utqiagvik (Barrow), Alaska, 2015

Individual ice cores were collected from Barrow Environmental Observatory in Barrow, Alaska, throughout 2013 and 2014. Cores were drilled along different transects to sample polygonal features (i.e. the trough, center and rim of high, transitional and low center polygons). Most cores were drilled around 1 meter in depth and a few deep cores were drilled around 3 meters in depth. Three-dimensional images of the frozen cores were constructed using a medical X-ray computed tomography (CT) scanner. TIFF files can be uploaded to ImageJ (an open-source imaging software) to examine soil structure and soil densities within each core.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 15-year research effort (2012-2027) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Powering Data Centers with Clean Energy: A Techno-Economic Case Study of Nuclear and Renewable Energy Dependability

Rising data demands from artificial intelligence (AI) and large language models (LLMs) generating images, videos, and text have prompted increased need for larger and more robust data centers in the United States. Major companies interested in these larger data centers face the choice of linking them to existing regional grids, building stand-alone power supplies onsite, or a combination of both. The request, review, and approval process for new transmission lines to grids in the United States, however, has grown in recent years to times spans rivaling those of new construction for nuclear power plants. Building an islanded power supply for each data center is therefore becoming a prominent option. In this case study, several technologies are modeled in techno-economic simulations for long-term system costs subject to fixed electricity demand from a singular data center. A 250 MWe data center is assumed with additional 50 MWe for resiliency. Techno-economic simulations are conducted using the Holistic Energy Resource Optimization Network (HERON) software, which is a part of the Framework for Optimization of Resources and Economics (FORCE) tool suite. Technologies considered include solar, wind, lithium-ion batteries, and several types of nuclear reactors: large-scale reactors, small modular reactors, and microreactors. A low- and high-cost estimate for each technology is assumed to develop a range of expected economic performance. Low-cost estimates included several clean energy production tax credits. Different combinations of renewable energy generators with nuclear reactors are considered, ranging from a fully renewable-powered data center to a fully nuclear-powered data center. Historic time series of wind and solar availability from the Texas grid are used to train a reduced order model; this model then generates unique time series with similar characteristics of the training dataset. Multiple scenarios of weather and subsequent operations are simulated for each renewable-nuclear combination to determine total costs throughout the project lifetime. Fully renewable-powered configurations required large amounts of installed capacity (GW scale) in the simulations to meet the fixed demand of the data center. This is due to some scenarios in the historical dataset which captured low-wind and low-solar days, requiring over-building of these technologies as well as batteries to compensate for the low amounts of electricity generation. Fully nuclear-powered configurations outperformed the fully renewable and mixed renewable-nuclear configurations in terms of cost, with ranges between $1B and $10B in 2023 USDs compared to $40B+ for fully renewable configurations. Of the nuclear technologies, small modular reactors performed better economically than large-scale nuclear models due to lower projected capital costs, and both performed better than the microreactor models. These results demonstrate the applicability of firm, dispatchable electricity resources from baseload generators like nuclear power plants for operating facilities that run at constant power without daily variability.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Demonstration and Automation of Reflected Target Optical Measurement for Heliostats

Accurate optical surfaces are a primary driver of concentrated solar power plant performance. Errors in pointing and tracking mirrors, the canting of individual mirror facets, and the surface slope of the mirror itself can be caused by errors during assembly, transportation, wind loading, gravity, and many other sources. The tools that exist to measure these error sources today largely rely on fringe deflectometry (SOFAST, QDec, others), or photogrammetry with targets attached to the mirror surface. Since 2022, NREL has been developing a measurement method called the Reflected Target Non-intrusive Assessment (ReTNA) system. This system differs from most established methods in that we perform deflectometry with a pattern of coded targets, identified in space with photogrammetry. Reflected target systems have several advantages over traditional fringe deflectometry systems. Firstly, they can be operated in bright or ambient lighting, a challenge for fringe systems that use a projector and screen. Reflected target systems also can use a much lighter and less expensive target than projector-based systems. Lastly, 2D slope measurement can be solved from a single image, which leads to several advantages for accommodating faster measurements and smaller sized targets. These advantages make ReTNA particularly well-suited for applications where there are space or lighting constraints, like performing heliostat quality assurance on an assembly line. It's also useful when a lightweight, flexible system is needed, like for heliostat developers to quickly measure a new heliostat design at different orientations, to observe gravitational effects on the mirror surface shape. In the last year, significant improvements were made to this tool to make it more useful for these applications. These improvements were focused around validation of the ReTNA measurement system, and automation of the setup and measurement process. First, we present an improved ReTNA layout, for use on the heliostat assembly line. Next, we detail the various changes to the ReTNA software and computer vision methods to automate data collection in this new setup, and lessons learned from this process. The goal with this new setup is to perform a full heliostat surface characterization without removing the mirror from the assembly line. Lastly, we share results from several ReTNA validation studies undertaken over the last year. These include repeated ReTNA measurement on demonstration mirror facets, comparisons with other optical measurement tools, and some studies aimed at quantifying the uncertainty of ReTNA measurement under various constraints (mirror-target spacing, camera resolution, etc.). These results are compared with 2024 HelioCon performance targets, and our planned next steps for the ReTNA measurement system are presented.

CSP↗
DOE OSTI2026

Optimal Operation of Residential High Performance Water Heater for Reduction of Electricity Cost and Peak Demand Through Field Validation

Water heating accounts for about 18% of a typical US home’s energy use. Modern water heaters have enabled control options through APIs, offering customers the opportunity to reduce their energy cost and peak demand by dynamically adjusting settings. A water heater’s capacity to store energy using its storage tank makes it an asset for peak demand reduction and energy cost savings. For this reason, a mixed-integer linear programming model is proposed to minimize the energy cost of a high-performance water heater while also reducing the peak demand of the residential household under a time-of-use utility rate by dynamically changing the water heater’s running mode. Specifically, a multi-objective optimization model is formulated to determine the mode settings of the water heater considering hot water use, time-of-use rate, and peak demand limit of the residential household. The mode settings are associated with different dead bands of water temperature for triggering on/off action of the heat pump and heating element. A 66-gal hybrid electric high performance water heater was used for numerical simulation and practical experiments. The simulation results were well aligned with measurements of practical experiments, validating the soundness of the thermodynamic model. In addition, reductions of energy cost, enabling affordability, and reducing peak demand are demonstrated. The research team also developed a software framework with dashboards to automatically and continuously monitor and manage devices.

Liu, Guodong [ORNL] (ORCID:0000000213498608)↗
DOE OSTI2024

CI/CD Efforts for Validation, Verification and Benchmarking OpenMP Implementations

Software developers must adapt to keep up with the changing capabilities of platforms so that they can utilize the power of High-Performance Computers (HPC), including exascale systems. OpenMP, a directive-based parallel programming model, allows developers to include directives to existing C, C++, or Fortran code to allow node level parallelism without compromising performance. This paper describes our CI/CD efforts to provide easy evaluation of the support of OpenMP across different compilers using existing testsuites and benchmark suites on HPC platforms. Our main contributions include (1) the set of a Continuous Integration (CI) and Continuous Development (CD) workflow that captures bugs and provides faster feedback to compiler developers, (2) an evaluation of OpenMP (offloading) implementations supported by AMD, HPE, GNU, LLVM, and Intel, and (3) evaluation of the quality of compilers across different heterogeneous HPC platforms. With the comprehensive testing through the CI/CD workflow, we aim to provide a comprehensive understanding of the current state of OpenMP (offloading) support in different compilers and heterogeneous platforms consisting of CPUs and GPUs from NVIDIA, AMD, and Intel.

Jarmusch, Aaron↗
DOE OSTI2026

AmeriFlux FLUXNET-1F US-Dk3 Duke Forest - loblolly pine

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-Dk3 Duke Forest - loblolly pine. This is the FLUXNET version of the carbon flux data for the site US-Dk3 Duke Forest - loblolly pine produced by applying the standard ONEFlux (1F) software. Site Description - The site was established in 1983 following a clear cut and a burn. Pinus taeda L. (loblolly pine) seedlings were planted at 2.4m by 2.4m spacing and ecosystem development has not been managed after planting. Canopy height increased from 16m in 2001 to 18m in 2004. The canopy is comprised primarily of P. taeda with some emergent Liquidambar styraciflua L. and a diverse and growing understory with 26 different woody species of diameter breast height 42.5 cm. The flux tower lies upwind of the CO2-enriched components of the free atmosphere carbon enrichment (FACE) facility located in the same pine forest. EC instrumentation is at 20.2m on a 22m tower.

Oishi, Chris [USDA Forest Service]↗
DOE OSTI2026

Persistent DynAMICS

Persistent DynAMICS is a lightweight software platform that enables distributed sensing systems to operate as a unified, responsive network. It integrates with existing sensors, data systems, and processing tools as an overlay, without requiring hardware replacement or increasing user burden. As data is collected, the system identifies situations that require additional attention and directs selected sensors to gather more information. For example, if a sensor detects an unusual condition along a pipeline, the system can task nearby sensors or different sensing modalities to confirm the event and focus data collection where it is needed. To support this, the platform forms temporary groups of sensors that work together to address specific objectives. Once complete, these groups are dissolved and resources are reassigned as needed. Communication is handled through an integrated messaging framework with client and server components, enabling reliable operation and data continuity even in low-bandwidth or intermittent connectivity environments.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Portable HCAL reconstruction in the CMS detector using the Alpaka library

CMS has deployed a number of different GPU algorithms at the High-Level Trigger (HLT) in Run 3. As the code base for GPU algorithms continues to grow, the burden for developing and maintaining separate implementations for GPU and CPU becomes increasingly challenging. To mitigate this, CMS has adopted the Alpaka (Abstraction Library for Parallel Kernel Acceleration) library as the performance portability solution to provide a single-code base for parallel execution on both GPUs and CPUs in CMS software (CMSSW). A direct CUDA version of HCAL energy reconstruction, called Minimization At Hcal, Iteratively (MAHI), has been deployed at the HLT in the 2022-2023 data taking period. This contribution will describe how the CUDA version is converted into a portable implementation using the Alpaka library. We will discuss the porting experience from CUDA to Alpaka, the validation process and the performance of the Alpaka version in CPU and GPU.

Kwok, Martin↗
DOE OSTI2026

A continuous symmetry breaking measure for finite clusters using Jensen-Shannon divergence

A quantitative measure of symmetry breaking is introduced that allows the quantification of which symmetries are most strongly broken due to the introduction of some kind of defect in a perfect structure. The method uses a statistical approach based on the Jensen-Shannon divergence. The measure is calculated by comparing the transformed atomic density function with its original. Software code is presented that carries the calculations out numerically using Monte Carlo methods. The behavior of this symmetry breaking measure is tested for various cases including finite size crystallites (where the surfaces break the crystallographic symmetry), atomic displacements from high symmetry positions, and collective motions of atoms due to rotations of rigid octahedra. Finally, the approach provides a powerful tool for assessing local symmetry breaking and offers new insights that can help researchers understand how different structural distortions affect different symmetry operations.

atomic & molecular structure↗
DOE OSTI2025

pyTCR: A tropical cyclone rainfall model for python

pyTCR is a climatology software package developed in the Python programming language. It integrates the capabilities of several legacy physical models and increases computational efficiency to allow rapid estimation of tropical cyclone (TC) rainfall consistent with the large-scale environment. Specifically, pyTCR implements a horizontally distributed and vertically integrated model [Zhu et al., 2013] for simulating rainfall driven by TCs. Along storm tracks, rainfall is estimated by computing the cross-boundary-layer, upward water vapor transport caused by different mechanisms including frictional convergence, vortex stretching, large-scale baroclinic effect (i.e., wind shear), topographic forcing, and radiative cooling [Lu et al., 2018]. The package provides essential functionalities for modeling and interpreting spatio-temporal TC rainfall data. pyTCR requires a limited number of model input parameters, making it a convenient and useful tool for analyzing rainfall mechanisms driven by TCs. To sample rare (most intense) rainfall events that are often of great societal interest, pyTCR adapts and leverages outputs from a statistical-dynamical TC downscaling model [Lin et al., 2023] capable of rapidly generating a large number of synthetic TCs given a certain climate. As a result, pyTCR significantly reduces computational effort and improves the efficiency in capturing extreme TC rainfall events at the tail of the distributions from limited datasets. Furthermore, the TC downscaling model is forced entirely by large-scale environmental conditions from reanalysis data or coupled General Circulation Models (GCMs), simplifying the projection of TC-induced rainfall and wind speed under future climate using pyTCR. Finally, pyTCR can be coupled with hydrological and wind models to assess risks associated with independent and compound events (e.g., storm surges and freshwater flooding).

54 ENVIRONMENTAL SCIENCES↗