Search NASA⌕ Search

SEARCH · Search NASA

Results for “source feedback”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

A high accuracy sequential solver for simulation and active control of a longitudinal combustion instability

A high accuracy convection scheme using a sequential solution technique has been developed and applied to simulate the longitudinal combustion instability and its active control. The scheme has been devised in the spirit of the Total Variation Diminishing (TVD) concept with special source term treatment. Due to the substantial heat release effect, a clear delineation of the key elements employed by the scheme, i.e., the adjustable damping factor and the source term treatment has been made. By comparing with the first-order upwind scheme previously utilized, the present results exhibit less damping and are free from spurious oscillations, offering improved quantitative accuracy while confirming the spectral analysis reported earlier. A simple feedback type of active control has been found to be capable of enhancing or attenuating the magnitude of the combustion instability.

Shyy, W.↗

Reducing The Noise Impact of Unmanned Aerial Vehicles by Flight Control System Augmentation

The aim of this thesis is to explore methods to reduce the noise impact of unmanned aerial vehicles operating within acoustically sensitive environments by flight control systemaugmentation. Two methods are investigated and include: (i) reduction of sound generatedby vehicle speed control while flying along a nominal path and (ii) reduction of acousticexposure by vehicle path control while flying at a nominal speed. Both methods requireincorporation of an acoustic model into the flight control system as an additional controlobjective and an acoustic metric to characterize primary noise sources dependent on vehiclestate. An acoustic model was developed based on Gutin’s work to estimate propeller noise,both to estimate source noise and observer noise using two separate acoustic metrics. Thesemethods can potentially mitigate the noise impact of unmanned aerial systems operatingnear residential communities.The baseline flight control system of a representative aircraft was augmented with acontrol law to reduce propeller noise using feedback control of the commanded flight speeduntil an acoustic target was met, based on the propeller noise model. This control approachfocuses on modifying flight speed only, with no perturbation to the trajectory. Multipleflight simulations were performed and the results showed that integrating an acoustic metricinto the flight control system of an unmanned aerial system is possible and useful. A secondmethod to mitigate the effects of noise on an observer was also pursued to optimize a tra-jectory in order to avoid an acoustically sensitive region during the path planning process.After the propeller noise model was incorporated into the vehicle system, simulations showedthat it is possible to reduce the noise impact on an observer through an optimization of thetrajectory with no perturbation to the flight speed.

Matthew B Galles↗

The reionization of the universe: The feedback of galaxy formation on the intergalactic medium

The thermal and ionization evolution of a uniform intergalactic medium (IGM) composed of H and He, undergoing reionization, including the mean effect of gas clumps embedded in a smoothly distributed ambient gas were calculated. The rate equations for ionization and recombination were solved together with the equations of energy conservation, including the effects of cosmological expansion, radiative and Compton cooling, and the diffuse flux emitted by the gas, and radiative transfer. The contribution to the continuum opacity of the universe due to the observed quasar absorption line clouds (QALC'S) were included. A variety of sources of photoionization, including quasars and primeval galaxies, as well as the possibility that hydrodynamical processes deposit thermal energy in the IGM were considered. Applications of these calculations including the evolution of the Ly-alpha forest clouds are described. A self-consistent treatment of the thermal and ionization history of the intergalactic medium (IGM) must take account of the growth of structure in the universe, since the mean density of the IGM corresponds primarily to the time-varying uncollapsed fraction of the baryon-electron component of the matter, and the collapsed fraction, in turn, can have a feedback effect on this uncollapsed fraction by releasing ionizing radiation and thermal energy and by contributing to the opacity of the universe. The coupled evolution of the IGM and the emerging structure with a special focus on the reionization of the IGM, which is believed to have been completed by some redshift z is approximately greater than 4, as inferred from the absence of the Gunn-Peterson effect in the spectra of high z quasars, are studied. The results and implications of detailed, numerical calculations of the thermal and ionization balance and radiative transfer in a uniform IGM of H and He, including the mean effect of an evolving distribution of gas clumps embedded in a smoothly distributed ambient gas is described.

Shapiro, Paul R.↗

The Response of the Quasi-Biennial Oscillation to Increased CO and its Modulation by Composition Feedbacks

The Quasi-Biennial Oscillation (QBO) impacts the large-scale circulation by altering lower stratospheric meridional temperature gradients which alter the propagation of upward propagating planetary waves. Proposed teleconnections of the QBO include impacts on the stratospheric polar vortices, extratropical surface winter climate, and the Madden-Julian Oscillation. However, long-term projections of the QBO remain highly uncertain. While recent multi-model investigations (Richter et al. 2019, Butchart et al. 2020) show that the amplitude of the QBO weakens robustly among models, changes in QBO period and stability remain highly uncertain. Here we examine the QBO response to increased greenhouse gases using the NASA Goddard Institute for Space Studies Middle Atmosphere Model E2.2 (Rind et al., 2020; Orbe et al. 2020). Compared to lower vertical resolution versions of ModelE, E2.2 also has a higher model top (0.002 hPa) and employs additional interactive non-orographic gravity wave drag sources from convection and shear, which produce a sufficiently realistic QBO, thus rendering it suitable for use in climate change studies. Overall, we find that both the QBO period and amplitude decrease in response to increased CO , the former related to increased lower stratospheric momentum fluxes (associated with convection) and the latter associated partly with a stronger residual mean circulation. Experiments integrated using fully interactive chemistry also reveal that ozone feedbacks significantly impact the magnitude of the QBO amplitude response. Finally, integrations using fixed (pre-industrial) sea surface temperatures (SST) show that the QBO amplitude responds differently to rapid adjustments versus SST feedbacks, as compared to the QBO period.

Quasi-Biennial Oscillation↗

Development of an advanced spacecraft tandem mass spectrometer

The purpose of this research was to apply current advanced technology in electronics and materials to the development of a miniaturized Tandem Mass Spectrometer that would have the potential for future development into a package suitable for spacecraft use. The mass spectrometer to be used as a basis for the tandem instrument would be a magnetic sector instrument, of Nier-Johnson configuration, as used on the Viking Mars Lander mission. This instrument configuration would then be matched with a suitable second stage MS to provide the benefits of tandem MS operation for rapid identification of unknown organic compounds. This tandem instrument is configured with a newly designed GC system to aid in separation of complex mixtures prior to MS analysis. A number of important results were achieved in the course of this project. Among them were the development of a miniaturized GC subsystem, with a unique desorber-injector, fully temperature feedback controlled oven with powered cooling for rapid reset to ambient conditions, a unique combination inlet system to the MS that provides for both membrane sampling and direct capillary column sample transfer, a compact and ruggedized alignment configuration for the MS, an improved ion source design for increased sensitivity, and a simple, rugged tandem MS configuration that is particularly adaptable to spacecraft use because of its low power and low vacuum pumping requirements. The potential applications of this research include use in manned spacecraft like the space station as a real-time detection and warning device for the presence of potentially harmful trace contaminants of the spacecraft atmosphere, use as an analytical device for evaluating samples collected on the Moon or a planetary surface, or even use in connection with monitoring potentially hazardous conditions that may exist in terrestrial locations such as launch pads, environmental test chambers or other sensitive areas. Commercial development of the technology could lead to a new family of environmental test instruments that would be small and portable, yet would give quick analyses of complex samples.

Drew, Russell C.↗

"GSFC FSB Application of Perspective-Based Inspections"

The scope of work described in our proposal consisted of developing inspection standards targeted to Branch-specific types of defects (gained from analysis of Branch project defect histories), and including Branch-relevant perspectives and questions to guide defect detection. The tailored inspection guidelines were to be applied on real Branch projects with support as needed from the technology infusion team. This still accurately describes the scope of work performed. It was originally proposed that the Perspective-Based inspection standard would be applied on three projects within the Branch: GPM, JWST, and SDO. Rather than apply the proposed standard to all three, we inserted a new step, in which the standard was instead applied on a single pilot project, cFE (described above). This decision was a good match for the Branch goals since, due to the "design for reuse" nature of cFE, inspections played an even more crucial than usual role in that development process. Also, since cFE is being designed to provide general-purpose functionality, key representatives fiom our target projects were involved in inspections of cFE to provide perspectives from different missions. In this way, they could get some exposure to and the chance to provide feedback on the proposed standards before applying them on their own projects. The Branch-baselined standards will still be applied on GPM, JWST, and SDO, although outside the time frame of this funding. Finally, we originally proposed using the analysis of Branch defect sources to indicate in which phases Perspective-Based inspections could provide the best potential for future improvement, although experience on previous Branch projects suggested that our efforts would likely be focused on requirements and code inspections. In the actual work, we focused exclusively on requirements inspections, as this was the highest-priority work currently being done on our cFE pilot project.

Shell, Elaine↗

Multivariable flight control synthesis and literal robustness analysis for an aeroelastic vehicle

An integrated flight/aeroelastic control law is developed analytically for a hypothetical large supersonic transport aircraft in which the first aeroelastic mode frequency of the fuselage (6 rad/sec) is near the short-period mode (2 rad/sec). The approach employed is based on a linear-quadratic-regulator (LQR) formulation (yielding model-following state-feedback gains), followed by asymptotic loop-transfer recovery of LQR robustness (to produce an output-feedback control law). The derivation is outlined, and numerical results comparing the performance and multivariate stability robustness of the present controller with those of a classical controller are presented in graphs. The two controllers are shown to have similar characteristics, even with respect to the sources of limitations on robustness.

Schmidt, David K.↗

Fiber Grating Coupled Light Source Capable of Tunable, Single Frequency Operation

Fiber Bragg grating coupled light sources can achieve tunable single-frequency (single axial and lateral spatial mode) operation by correcting for a quadratic phase variation in the lateral dimension using an aperture stop. The output of a quasi-monochromatic light source such as a Fabry Perot laser diode is astigmatic. As a consequence of the astigmatism, coupling geometrics that accommodate the transverse numerical aperture of the laser are defocused in the lateral dimension, even for apsherical optics. The mismatch produces the quadratic phase variation in the feedback along the lateral axis at the facet of the laser that excites lateral modes of higher order than the TM 00 . Because the instability entails excitation of higher order lateral submodes, single frequency operation also is accomplished by using fiber Bragg gratings whose bandwidth is narrower than the submode spacing. This technique is particularly pertinent to the use of lensed fiber gratings in lieu of discrete coupling optics. Stable device operation requires overall phase match between the fed-back signal and the laser output. The fiber Bragg grating acts as a phase-preserving mirror when the Bragg condition is met precisely. The phase-match condition is maintained throughout the fiber tuning range by matching the Fabry-Perot axial mode wavelength to the passband center wavelength of the Bragg grating.

Michael A Krainak↗

Curvature-Based Wavefront Sensor for Use on Extended, Arbitrary, Low-Contract Scenes Final Technical Report August 2004

A small amount of work has been done on this project; the strategy to be adopted has been better defined, though no experimental work has been started. 1) Wavefront error signals: The best choice appears use a lenslet array at a pupil image to produce defocused image pairs for each subaperture. Then use the method proposed by Molodij et al. to produce subaperture curvature signals. Basically, this method samples a moderate number of locations in the image where the value of the image Laplacian is high, then taking the curvature signal from the difference of the Laplacians of the extrafocal images at those locations. The tip-tilt error is obtained from the temporal dependence of the first spatial derivatives of an in-focus image, at selected locations where these derivatives are significant. The wavefront tilt can be obtained from the full-aperture image. 2) Extrafocal image generation: The important aspect here is to generate symmetrically defocused images, with dynamically adjustable defocus. The adjustment is needed because larger defocus is required before the feedback loop is closed, and at times when the seeing is worse. It may be that the usual membrane mirror is the best choice, though other options should be explored. 3) Detector: Since the proposed sensor is to work on solar granulation, rather than a point source, an array detector for each subaperture is required. A fast CMOS camera such as that developed by the National Solar Observatory would be a satisfactory choice. 4) Processing: Processing requirements have not been defined in detail, though significantly fewer operations per cycle are required than for a correlation tracker.

LaBonte, Barry J.↗

Optical and Near-Infrared Coronagraphy of the Quasar 3C 273

We present preliminary results of our observations of the ultraluminous quasar 3C 273 using the HST/STIS coronagraph and the Keck/NIRC2 vortex coronagraph to provide high-contrast imaging of the inner regions of the host galaxy in the optical and near-infrared. We use reference star differential imaging (RDI) techniques developed for high-contrast imaging of exoplanets and circumstellar disks to observe the morphology of features down to the inner few tenths of arcseconds (inner few 100s of pc) around the quasar point source. Broadband optical (50CORON) coronagraphy with STIS reveals the inner structure of jets and shocks, while Ks-band coronagraphy with NIRC2 suggests the presence of a candidate kpc-scale circumnuclear disk. If confirmed, this disk plays a potentially important role in driving the extreme feedback state of 3C 273 by up-regulating accretion, and its presence is consistent with recent observations of atomic and molecular gas in this system at larger spatial scales. We conclude by discussing potential applications of the observing techniques we applied to 3C 273 to other PSF-dominated systems at moderate redshifts to detect features such as circumnuclear disks and multiple nuclei with direct imaging.

Kevin Fogarty↗

Active Control of Fan Noise: Feasibility Study: Theoretical Analysis for Coupling of Active Noise Control Actuator Ring Sources to an Annular Duct with Flow - Volume 6

The objective of this effort is to develop an analytical model for the coupling of active noise control (ANC) piston-type actuators that are mounted flush to the inner and outer walls of an annular duct to the modes in the duct generated by the actuator motion. The analysis will be used to couple the ANC actuators to the modal analysis propagation computer program for the annular duct, to predict the effects of active suppression of fan-generated engine noise sources. This combined program will then be available to assist in the design or evaluation of ANC systems in fan engine annular exhaust ducts. An analysis has been developed to predict the modes generated in an annular duct due to the coupling of flush-mounted ring actuators on the inner and outer walls of the duct. The analysis has been combined with a previous analysis for the coupling of modes to a cylindrical duct in a FORTRAN computer program to perform the computations. The method includes the effects of uniform mean flow in the duct. The program can be used for design or evaluation purposes for active noise control hardware for turbofan engines. Predictions for some sample cases modeled after the geometry of the NASA Lewis ANC Fan indicate very efficient coupling in both the inlet and exhaust ducts for the m = 6 spinning mode at frequencies where only a single radial mode is cut-on. Radial mode content in higher order cut-off modes at the source plane and the required actuator displacement amplitude to achieve 110 dB SPL levels in the desired mode were predicted. Equivalent cases with and without flow were examined for the cylindrical and annular geometry, and little difference was found for a duct flow Mach number of 0.1. The actuator ring coupling program will be adapted as a subroutine to the cylindrical duct modal analysis and the exhaust duct modal analysis. This will allow the fan source to be defined in terms of characteristic modes at the fan source plane and predict the propagation to the arbitrarily-located ANC source plane. The actuator velocities can then be determined to generate the anti-phase mode. The resulting combined fan source/ANC pressure can then be calculated at any desired wall sensor position. The actuator velocities can be determined manually or using a simulation of a control system feedback loop. This will provide a very useful ANC system design and evaluation tool.

Kraft, R. E.↗

Multiple high voltage output DC-to-DC power converter

Disclosed is a multiple output DC-to-DC converter. The DC input power is filtered and passed through a chopper preregulator. The chopper output is then passed through a current source inverter controlled by a squarewave generator. The resultant AC is passed through the primary winding of a transformer, with high voltages induced in a plurality of secondary windings. The high voltage secondary outputs are each solid-state rectified for passage to individual output loads. Multiple feedback loops control the operation of the chopper preregulator, one being responsive to the current through the primary winding and another responsive to the DC voltage level at a selected output.

Cronin, Donald L.↗

Ground and Airborne Methane Measurements using Optical Parametric Amplifiers

We report on an initial airborne demonstration of atmospheric methane column measurements at 1.65 micrometers using a widely tunable, seeded optical parametric amplifier (OPA) lidar and a photon counting detector. Methane is an important greenhouse gas and accurate knowledge of its sources and sinks is needed for climate modeling. Our lidar system uses 20 pulses at increasing wavelengths and integrated path differential absorption (IPDA) to map a methane line at 1650.9 nanometers. The wavelengths are generated by using a Nd:YAG pump laser at 1064.5 nanometers and distributed feedback diode laser at 1650.9 nanometers and a periodically-poled lithium niobate (PPLN) crystal. The pulse width was 3 nanoseconds and the pulse repetition rate was 6.28 KHz. The outgoing energy was approximately 13 microJoules/pulse. A commercial 20 nanometer diameter fiber-coupled telescope with a photon counting detector operated in analog mode with a 0.8 nanometer bandpass filter was used as the lidar receiver. The lidar system was integrated on NASA's DC-8 flying laboratory, based at Dryden Airborne operations Facility (DAOF) in Palmdale CA. Three flights were performed in the central valley of California. Each flight lasted about 2.5 hours and it consisted of several flight segments at constant altitudes at approximately 3, 4.5, 6, 7.6, 9.1, 10.6 km (l0, 15, 20, 25, 30, 35 kft). An in-situ cavity ring down spectrometer made by Picarro Inc. was flown along with the lidar instrument provided us with the "truth" i.e. the local CH4, CO2 and H2O concentrations at the constant flight altitude segments. Using the aircraft's altitude, GPS, and meteorological data we calculated the theoretical differential optical depth of the methane absorption at increasing altitudes. Our results showed good agreement between the experimentally derived optical depth measurements from the lidar instrument and theoretical calculations as the flight altitude was increased from 3 to 10.6 kilometers, assuming a constant methane mixing ratio of 1.8 parts per million. The in-situ spectrometer did not show any significant deviations from the ambient concentrations. Further analysis using meteorological data from the Global Modeling and Assimilation Office (http://gmao.gsfc.nasa.gov/) to derive the theoretical optical depth also showed good agreement with the experimentally derived values. The OPA lidar system with slight modifications has also been used to measure CO2, water vapor, and CO in the near and mid-infrared spectral regions on the ground.

Riris, Haris↗

CARETS: A prototype regional environmental information system. Volume 3: Toward a national land use information system

It is recommended that a national land use information system be established by an agency of the Federal Government. This recommendation comes at a time of increasing demand for scientific information in support of environmentally relevant land use planning and management at all levels of government. It is also a time when new airborne and spaceborne remote sensors, tested in cooperation with the National Aeronautics and Space Administration (NASA) and the Earth Resources Observation Systems (EROS) Program of the Department of the Interior, make possible the gathering of land use information rapidly and on an unprecedented scale. Furthermore, information handling technology is developing toward a capability to receive, store, and disseminate the huge quantities of data that would be involved. The recommendation for the national land use information system is based upon careful analysis of the results of remote sensing experiments funded by NASA, EROS, and the Geography Program of the Geological Survey, with specific examples drawn from the demonstration project known as the Central Atlantic Regional Ecological Test Site (CARETS). CARETS is cast in the framework of a regional land use information system, channeling the flow bf information generated in response to users' declaration of their needs, through stages dealing with remote sensing data gathering systems, data processing and land mensuration, calibration in-terms of environmental impact, and evaluation with feedback from users. The proposed system would develop and implement a unified approach to the description and interpretation of the changing uses of the nation's land resources, building upon the base of interagency and intergovernmental cooperation already achieved in the experimental work to date. The land use data base that is being derived from high-altitude aerial color infrared photography would be the initial component of the recommended system. High-altitude photographic coverage would immediately be extended to as much of the nation as possible as technological developments and economic considerations permit. The system would later expand to include multiple-sensor, multiple-platform data sources. Six system characteristics are recommended: (1) High capacity storage of data available for quick retrieval, inexpensive processing, and update, (2) provision of accuracy appropriate to the scale of survey or to the level of detail dictated by different types of management and decision requirements; (3) permanent, publicly accessible sensor records for historical interpretation; (4) compatibility of the recording, storage, and retrieval system with all types of inputs, from ground observer to satellite; (5) products of diverse formats and scales, responsive to user feedback; (6) and standardization of formats, scales, and storage inputs to permit nationwide comparability.

Land use mapping↗

An investigation into pilot and system response to critical in-flight events. Volume 1: Executive summary

Critical in-flight events (CIFE) that threaten the aircraft were studied. The scope of the CIFE was described and defined with emphasis on characterizing event development, detection and assessment; pilot information requirements, sources, acquisition, and interpretation, pilot response options, decision processed, and decision implementation and event outcome. Detailed scenarios were developed for use in simulators and paper and pencil testing for developing relationships between pilot performance and background information as well as for an analysis of pilot reaction decision and feedback processes. Statistical relationships among pilot characteristics and observed responses to CIFE's were developed.

Rockwell, T. H.↗

Dynamics of Molecular Hydrogen in Hypersaline Microbial Mars

Early Earth microbial communities that centered around the anaerobic decomposition of organic molecular hydrogen as a carrier of electrons, regulator of energy metabolism, and facilitator of syntroph'c microbial interactions. The advent of oxygenic photosynthetic organisms added a highly dynamic and potentially dominant term to the hydrogen economy of these communities. We have examined the daily variations of hydrogen concentrations in cyanobacteria-dominated microbial mats from hypersaline ponds in Baja California Sur, Mexico. These mats bring together phototrophic and anaerobic bacteria (along with virtually all other trophic groups) in a spatially ordered and chemically dynamic matrix that provides a good analog for early Earth microbial ecosystems. Hydrogen concentrations in the photic zone of the mat can be three orders of magnitude or more higher than in the photic zone, which are, in turn, an order of magnitude higher than in the unconsolidated sediments underlying the mat community. Within the photic zone, hydrogen concentrations can fluctuate dramatically during the diel (24 hour day-night) cycle, ranging from less than 0.001% during the day to nearly 10% at night. The resultant nighttime flux of hydrogen from the mat to the environment was up to 17% of the daytime oxygen flux. The daily pattern observed is highly dependent on cyanobacterial species composition within the mat, with Lyngbya-dominated systems having a much greater dynamic range than those dominated by Microcoleus; this may relate largely to differing degrees of nitrogen-fixing and fermentative activity in the two mats. The greatest H2 concentrations and fluxes were observed in the absence of oxygen, suggesting an important potential feedback control in the context of the evolution of atmospheric composition. The impact of adding this highly dynamic photosynthetic term to the hydrogen economy of early microbial ecosystems must have been substantial. From an evolutionary standpoint, the H2 generated in mats could have represented a very important new source of electrons and energy - but one that could not be harnessed without substantial adaptation to the highly variable chemistry of the mat surface. In addition, the emergent chemistry of anaerobic communities is often highly dependent on ambient hydrogen concentrations, so that incorporation of these communities into photosynthetic mats could have significantly affected the composition and flux of reduced "biosignature' gases to the environment.

Hoehler, Tori M.↗

A Comprehensive Characterization of Microorganisms and Allergens in Spacecraft Environment

The determination of risk from infectious disease during long-duration missions is composed of several factors including the concentration and the characteristics of the infectious agent. Thus, a thorough knowledge of the microorganisms aboard spacecraft is essential in mitigating infectious disease risk to the crew. While stringent steps are taken to minimize the transfer of potential pathogens to spacecraft, several medically significant organisms have been isolated from both the Mir and International Space Station (ISS). Historically, the method for isolation and identification of microorganisms from spacecraft environmental samples depended upon their growth on culture media. Unfortunately, only a fraction of the organisms may grow on a culture medium, potentially omitting those microorganisms whose nutritional and physical requirements for growth are not met. Thus, several pathogens may not have been detected, such as Legionella pneumophila, the etiological agent of Legionnaire s disease. We hypothesize that environmental analysis using non-culture-based technologies will reveal microorganisms, allergens, and microbial toxins not previously reported in spacecraft, allowing for a more complete health assessment. The development of techniques for this flight experiment, operationally named SWAB, has already provided advances in NASA laboratory processes and beneficial information toward human health risk assessment. The translation of 16S ribosomal DNA sequencing for the identification of bacteria from the SWAB experiment to nominal operations has increased bacterial speciation of environmental isolates from previous flights three fold compared to previous conventional methodology. The incorporation of molecular-based DNA fingerprinting using repetitive sequence-based polymerase chain reaction (rep-PCR) into the capabilities of the laboratory has provided a methodology to track microorganisms between crewmembers and their environment. Both 16S ribosomal DNA identification and bacterial fingerprinting have improved NASA s capability to better understand spacecraft environments and determine the source of contamination events. Preflight sampling has been completed for air, surface, and water samples. In-flight sample collection has been completed for a total of 8 air and surface sample collection sessions. In-flight hardware has performed well and the surface sampling device received positive feedback from the crew for its ease of use. While processing and analysis continue for these samples, early results have begun to provide information on the spacecraft environment. Using a method called Denaturing Gradient Gel Electrophoresis (DGGE), several air and samples were evaluated to determine the types of organisms that were present. Using only molecular techniques, DGGE does not depend on any microbial growth on culture media, allowing a more comprehensive assessment of the spacecraft interior. Preliminary results have identified several microorganisms that would not have been isolated using current technology, though none of these organisms would be considered medically significant. Interestingly, the isolation of Gram negative organisms is greater using DGGE than conventional media based isolation. The cause of this finding is unclear, though it may be the result of the technique s ability to isolate both viable and non-viable bacteria. The next phase of the SWAB sample analysis is the use of quantitative polymerase chain reaction (QPCR) to look for specific medically significant organisms. While not as broad as DGGE, QPCR is much more sensitive and may reveal findings that were not seen during the initial evaluation. Together, this information will lead toward an accurate microbial risk assessment to help set flight requirements to protect the safety, health, and performance of the crew.

Castro, V.A.↗

Dynamical Mechanisms Underlying the 2022/23 California Flooding: Analysis With A Stationary Wave Model

In late December 2022 and the first half of January 2023, much of California experienced an unprecedented series of atmospheric rivers that produced heavy rains and near-record flooding. Previous work shows that a chain of dynamical events contributed to the extreme precipitation, including the development of a Rossby wave (as a result of forcing linked to the MJO) that emerged from the Indian Ocean in mid-December, and the subsequent development of a persistent positive Pacific North American (PNA) pattern that ultimately directed moisture onto the US West Coast starting in late December. Here, we use a stationary wave model (SWM) to further elucidate the dynamical and thermodynamical processes that drove the aforementioned chain of events. The results reveal the following: 1) The mid-December Rossby wave was likely induced by vorticity stretching and advection in the middle East linked indirectly to the MJO, 2) The initial development of the PNA in late December was triggered by transient and stretching sources of vorticity in the Pacific that were themselves induced by the aforementioned Rossby wave, and 3) The PNA was maintained through mid-January in part by diabatic heating west of Hawaii that was associated with anomalous precipitation influenced by the PNA circulation anomalies, thus representing a feedback on the PNA. One key finding from the SWM analysis is the limited direct role of tropical heating for inducing any of the dynamical mechanisms related to the California extreme event.

Anthony M. DeAngelis↗