Search NASA⌕ Search

SEARCH · Search NASA

Results for “steady-state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Some Finite Difference Solutions of the Laminar Compressible Boundary Layer Showing the Effects of Upstream Transpiration Cooling

Three numerical solutions of the partial differential equations describing the compressible laminar boundary layer are obtained by the finite difference method described in reports by I. Flugge-Lotz, D.C. Baxter, and this author. The solutions apply to steady-state supersonic flow without pressure gradient, over a cold wall and over an adiabatic wall, both having transpiration cooling upstream, and over an adiabatic wall with upstream cooling but without upstream transpiration. It is shown that for a given upstream wall temperature, upstream transpiration cooling affords much better protection to the adiabatic solid wall than does upstream cooling without transpiration. The results of the numerical solutions are compared with those of approximate solutions. The thermal results of the finite difference solution lie between the results of Rubesin and Inouye, and those of Libby and Pallone. When the skin-friction results of one finite difference solution are used in the thermal analysis of Rubesin and Inouye, improved agreement between the thermal results of the two methods of solution is obtained.

Howe, John T.↗
NASA NTRS1961

Wind-Tunnel Investigation of Paraglider Models at Supersonic Speeds

An investigation was made in the Langley Unitary Plan wind tunnel to determine the behavior of paraglider models at moderate to high supersonic speeds. The models were deployed from a sting in the supersonic stream and steady-state aerodynamic performance data were obtained. Maximum values of the lift-drag ratio were about 1.4 at a Mach number of 2.65 and about 1.2 at a Mach number of 4.65. The angles of attack over which the models could be flown were limited by unsteady behavior of the canopy.

Taylor, Robert T.↗
NASA NTRS1959

Investigation of the Characteristics of an Acceleration-Type Take-Off Indicator in a Large Jet Airplane

The characteristics of a proposed acceleration-type take-off indicator were observed during take-off runs of a large jet airplane. The instrument performed its function satisfactorily. It showed an essentially constant reading, which agreed closely with the predicted value, throughout the take-off except for about the first 135 feet of the ground roll during which the starting windup of the indicator pointer occurred. Although oscillating longitudinal accelerations at the instrument location were as much as +/- 50 percent of the steady-state acceleration, the instrument showed only small excursions from the mean reading equivalent to not more than +/- 5 percent of the mean reading and was considered to be satisfactorily readable.

Kolnick, Joseph J.↗
NASA NTRS1959

The Effects of Target and Missile Characteristics on Theoretical Minimum Miss Distance for a Beam-Rider Guidance System in the Presence of Noise

A study has been made to determine the relative importance of those factors which place an inherent limitation on the minimum obtainable miss distance for a beam-rider navigation system operating in the presence of glint noise and target evasive maneuver. Target and missile motions are assumed to be coplanar. The factors considered are the missile natural frequencies and damping ratios, missile steady-state acceleration capabilities, target evasive maneuver characteristics, and angular scintillation noise characteristics.

Stewart, Elwood C.↗
NASA NTRS1961

A Wind-Tunnel Investigation of a 4-Foot-Diameter Ducted Fan Mounted on the Tip of a Semispan Wing

Power, wing angle of attack, and the angle of the duct relative to the wing were varied to achieve a specified lift and thrust for a forward velocity range from 0 to 140 knots. In this manner a so-called transition program of steady-state conditions was defined over the velocity range. It was found-that large pitch-up moments resulted when the ducted fan was operated at an angle of attack to the air stream. A deflected vane installed in the high-energy air at the duct exit was helpful in reducing these pitch-up moments. Large downwash angles were induced by the ducted fan at a selected horizontal-tail location. The possibility of using guide vanes in the duct inlet to vary thrust for the purpose of roll control at low forward speeds was examined.The maximum incremental thrust available at zero forward velocity was found to be 11% of the total thrust required at that speed.

Yaggy, Paul F.↗
NASA NTRS1961

A Method of Determining Aerodynamic-Influence Coefficients from Wind-Tunnel Data for Wings at Supersonic Speeds

A method is described for determining aerodynamic-influence coefficients from wind-tunnel data for calculating the steady-state load distribution on a wing with arbitrary angle-of-attack distribution at supersonic speeds. The method combines linearized theory with empirical adjustments in order to give accurate results over a wide range of angles of attack. The experimented data required are pressure distributions measured on a flat wing of the desired planform at the desired Mach number and over the desired range of angles of attack. The method has been tested by applying it to wind-tunnel data measured at Mach numbers of 1.61 and 2.01 on wings of the same planform but of different surface shapes. Influence coefficients adjusted to fit the flat wing gave good predictions of the spanwise and chord-wise distributions of loadings measured on twisted and cambered wings.

Gainer, Patrick A.↗
NASA NTRS1955

Over-All Performance of J65-B3 Turbojet Engine for Reynolds Number Indices from 0.8 to 0.2

The steady-state over-all performance characteristics of the J65-B3 turbojet engine were determined in an altitude test chamber for four exhaust-nozzle areas at Reynolds number indices of 0.8, 0.4, and 0.2. This range of Reynolds number indices corresponds to a range of altitudes from about sea level to 51,500 feet at a flight Mach number of 0.8. Generalized data are presented to allow calculation of engine performance at any flight condition corresponding to a Reynolds number index within the range investigated. Engine performance calculated from these generalized data is presented for seven altitudes over a range of flight speeds from zero to about 1100 knots. The use of an exhaust nozzle sized to give rated perforce at sea level would permit operation near the point of minimum specific fuel consumption for a wide range of flight conditions and engine speeds.

Fenn, David B.↗
NASA NTRS1955

Qualitative Results from a Flight Investigation to Determine Aileron Effectiveness of Two Rocket-Propelled 1/20-Scale Models of the MX -76 Missile

Free-flight tests of two rocket-propelled l/20-scale models of the Bell MX-776 missile have been conducted to obtain measurements of the aileron deflection required to counteract the induced rolling moments caused by combined angles of attack and sideslip and thus to determine whether the ailerons provided were capable of controlling the model at the attitudes produced by the test conditions. Inability to obtain reasonably steady-state conditions and superimposed high-frequency oscillations in the data precluded any detailed analysis of the results obtained from the tests. For these reasons, the data presented are limited largely to qualitative results.

Stevens, Joseph E.↗
NASA NTRS1968

Flight Test of a 40-Foot Nominal-Diameter Disk-Gap-Band Parachute Deployed at a Mach Number of 1.91 and a Dynamic Pressure of 11.6 Pounds per Square Foot

A 40-foot (12.2 meter) nominal-diameter disk-gap-band parachute was flight tested as part of the NASA Supersonic Planetary Entry Decelerator Program (SPED-I). The test parachute was ejected by a deployment mortar from an instrumented payload at an altitude of 140,000 feet (42.5 kilometers). The payload was at a Mach number of 1.91 and the dynamic pressure was 11.6 pounds per square foot (555 newtons per square meter) at the time the parachute deployment mortar was fired. The parachute reached suspension line stretch in 0.43 second with a resultant snatch force loading of 1990 pounds (8850 newtons). The maximum parachute opening load of 6500 pounds (28,910 newtons) came 0.61 second later at a total elapsed time from mortar firing of 1.04 seconds. The first full inflation occurred at 1.12 seconds and stable inflation was achieved at approximately 1.60 seconds. The parachute had an average axial-force coefficient of 0.53 during the deceleration period. During the steady-state descent portion of the flight test, the average effective drag coefficient was also 0.53 and pitch-yaw oscillations of the canopy averaged less than 10 degrees in the altitude region above 100,000 feet (30.5 meters).

EXPERIMENTS↗
NASA NTRS1967

Flight Test of a 30-Foot Nominal-Diameter Disk-Gap-Band Parachute Deployed at Mach 1.56 and Dynamic Pressure of 11.4 Pounds per Square Foot

A 30-foot (9.1 meter) nominal-diameter disk-gap-band parachute (reference area 707 sq ft (65.7 m(exp 2)) was flight tested with a 200-pound (90.7 kg) instrumented payload as part of the NASA Planetary Entry Parachute Program. A deployment mortar ejected the test parachute when the payload was at a Mach number of 1.56 and a dynamic pressure of 11.4 lb/sq ft (546 newtons per m 2 ) at an altitude of 127,500 feet (38.86 km). The parachute reached suspension line stretch in 0.37 second resulting in a snatch force loading of 1270 pounds (5650 N). Canopy inflation began 0.10 second after line stretch. A delay in the opening process occurred and was apparently due to a momentary interference of the glass-fiber shroud used in packing the parachute bag in the mortar. Continuous canopy inflation began 0.73 second after initiation of deployment and 0.21 second later full inflation was attained for a total elapsed time from mortar fire of 0.94 second. The maximum opening load of 3915 pounds (17,400 newtons) occurred at the time the canopy was first fully opened. The parachute exhibited an average drag coefficient of 0.52 during the deceleration period and pitch-yaw oscillations of the canopy were less than 5 degrees. During the steady-state descent portion of the test period, the average effective drag coefficient was about 0.47 (based on vertical descent velocity and total system weight).

EXPERIMENTS↗
NASA NTRS1967

Flight Test of 31.2 Diameter Modified Ringsail Parachute Deployed at Mach 1.39, Dynamic Pressure 11 Pounds per Square Foot

A 31.2-foot (9.51 meter) nominal diameter (reference area 764 ft(exp 2) (71.0 m(exp 2)) ringsail parachute modified to provide 15-percent geometric porosity was flight tested while attached to a 201-pound mass (91.2 kilogram) instrumented payload as part of the rocket launch portion of the NASA Planetary Entry Parachute Program (PEPP). The parachute deployment was initiated by the firing of a mortar at a Mach number of 1.39 and a dynamic pressure of 11.0 lb/ft(exp 2) (527 newtons/m(exp 2)) at an altitude of 122,500 feet (37.3 kilometers). The parachute deployed to suspension-line stretch (snatch force) in 0.35 second, and 0.12 second later the drag force increase associated with parachute inflation began. The parachute inflated in 0.24 second to the full-open condition for a total elapsed opening time of 0.71 second. The maximum opening load of 3970 pounds (17,700 newtons) came at the time the parachute was just fully opened. During the deceleration period, the parachute exhibited an average drag coefficient of 0.52 and oscillations of the parachute canopy were less than 5 degrees. During the steady-state terminal descent portion of the test period, the average effective drag coefficient (based on vertical descent velocity) was 0.52.

TESTS↗
NASA NTRS1970

Deployment and Performance Characteristics of 5-Foot Diameter (1.5m) Attached Inflatable Decelerators from Mach Numbers 2.2-4.4

Deployment characteristics and steady-state performance data were obtained over the Mach number range from 2.2 to 4.4 and at angles of attack from 0 degrees to l0 degrees. All attached inflatable decelerator (AID) models deployed successfully and exhibited flutter-free performance after deployment. Shock loads commonly associated with inflation of parachutes during deployment were not experienced. Force and moment data and ram-air pressure data were obtained throughout the Mach number range and at angles of attack from 0 degrees to l0 degrees. The high drag coefficient of 1.14 was in good agreement with the value predicted by the theory used in the design and indicated other AID shapes may be designed on a rational basis with a high degree of confidence.

TESTS↗
NASA NTRS1955

An Evaluation of the Roll-Rate Stabilization System of the Sidewinder Missile at Mach Numbers from 0.9 to 2.3

A linear stability analysis and flight-test investigation has been performed on a rolleron-type roll-rate stabilization system for a canard-type missile configuration through a Mach number range from 0.9 to 2.3. This type damper provides roll damping by the action of gyro-actuated uncoupled wing-tip ailerons. A dynamic roll instability predicted by the analysis was confirmed by flight testing and was subsequently eliminated by the introduction of control-surface damping about the rolleron hinge line. The control-surface damping was provided by an orifice-type damper contained within the control surface. Steady-state rolling velocities were at all times less than 1 radian per second between the Mach numbers of 0.9 to 2.3 on the configurations tested. No adverse longitudinal effects were experienced in flight because of the tendency of the free-floating rollerons to couple into the pitching motion at the low angles of attack and disturbance levels investigated herein after the introduction of control-surface damping.

Nason, Martin L.↗
NASA NTRS1955

Preliminary Results of the Determination of Inlet-Pressure Distortion Effects on Compressor Stall and Altitude Operating Limits of the J57-P-1 Turbojet Engine

During an investigation of the J57-P-1 turbojet engine in the Lewis altitude wind tunnel, effects of inlet-flow distortion on engine stall characteristics and operating limits were determined. In addition to a uniform inlet-flow profile, the inlet-pressure distortions imposed included two radial, two circumferential, and one combined radial-circumferential profile. Data were obtained over a range of compressor speeds at an altitude of 50,000 and a flight Mach number of 0.8; in addition, the high- and low-speed engine operating limits were investigated up to the maximum operable altitude. The effect of changing the compressor bleed position on the stall and operating limits was determined for one of the inlet distortions. The circumferential distortions lowered the compressor stall pressure ratios; this resulted in less fuel-flow margin between steady-state operation and compressor stall. Consequently, the altitude operating Limits with circumferential distortions were reduced compared with the uniform inlet profile. Radial inlet-pressure distortions increased the pressure ratio required for compressor stall over that obtained with uniform inlet flow; this resulted in higher altitude operating limits. Likewise, the stall-limit fuel flows required with the radial inlet-pressure distortions were considerably higher than those obtained with the uniform inlet-pressure profile. A combined radial-circumferential inlet distortion had effects on the engine similar to the circumferential distortion. Bleeding air between the two compressors eliminated the low-speed stall limit and thus permitted higher altitude operation than was possible without compressor bleed.

Wallner, L. E.↗
NASA NTRS1951

Control Performance of General Electric Fuel and Torque Regulator Operating on T31-3 Turbine-Propeller Engine in Sea-Level Test Stand

A .General Electric fuel and torque regulator was tested in conjunction with a T31-3 turbine-propeller engine in the sea-level static test stand at the NACA Lewis laboratory. The engine and control were operated over the entire speed range: 11,000 rpm, nominal flight idle, to 13,000 rpm, full power. Steady-state and transient data were recorded and are presented with a description of the four control loops being used in the system. Results of this investigation indicated that single-lever control operation was satisfactory under conditions of test. Transient data presented showed that turbine-outlet temperature did overshoot maximum operating value on acceleration but that the time duration of overshoot did not exceed approximately 1 second. This temperature limiting resulted from a control on fuel flow as a function of engine speed. Speed and torque first reached their desired values 0.4 second from the time of change in power-setting lever position. Maximum speed overshoot was 3 percent.

Oppenheimer, Frank L.↗
NASA NTRS1958

Some Altitude Operational Characteristics of a Prototype Iroquois Turbojet Engine. COORD. NO. AF-P-6

The evaluation of the altitude operational characteristics was part of the over-all investigation of the early developmental Iroquois engine. Engine steady-state windmilling characteristics were evaluated over a range of flight Mach numbers from 0.48 to 1.72 at altitudes of 35,000 and 50,000 feet. Engine altitude ignition limits were obtained over a range of flight Mach numbers from 0.5 to 1.5 with the standard engine ignition system and also with an oxygen boost system. A short investigation of high-speed altitude reignition following combustor blowout was conducted.

Peters, Daniel J.↗
NASA NTRS1951

Investigation of Surge Characteristics of XJ34-WE-32 Turbojet Engine

Surge characteristics of the XJ34-WE-32 turbojet engine were determined over a range of altitudes. Several typical oscillograph traces during which surge occurred are presented. The effect of altitude on the surge line and it's relation to the steady-state operating region are shown.

Groesbeck, Donald E.↗
NASA NTRS1950

Preliminary Performance Data on Westinghouse Electronic Power Regulator Operating on J34-WE-32 Turbojet Engine in Altitude Wind Tunnel

The behavior of the Westinghouse electronic power regulator operating on a J34-WE-32 turbojet engine was investigated in the NACA Lewis altitude wind tunnel at the request of the Bureau of Aeronautics, Department of the Navy. The object of the program was to determine the, steady-state stability and transient characteristics of the engine under control at various altitudes and ram pressure ratios, without afterburning. Recordings of the response of the following parameters to step changes in power lever position throughout the available operating range of the engine were obtained; ram pressure ratio, compressor-discharge pressure, exhaust-nozzle area, engine speed, turbine-outlet temperature, fuel-valve position, jet thrust, air flow, turbine-discharge pressure, fuel flow, throttle position, and boost-pump pressure. Representative preliminary data showing the actual time response of these variables are presented. These data are presented in the form of reproductions of oscillographic traces.

Ketchum, James R.↗