Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Electrical-Discharge-Machining Contamination Removal from Metal Additively Manufactured Components

The use of an electrochemical dissolution process is shown to remove the recast layer contamination from the surfaces of electrical-discharge-machining cut components, as well as the interior exposed surfaces of the structure. The solution chemistry, cell potential, and exposure time are all relevant interdependent variables. Optimization of the electrode geometry should be made for each type of component. For the case of Cu-Zn recast contamination of 300-series alloy components, surface composition analysis indicates that complete electrochemical dissolution is achieved using a dilute solution of nitric acid (HNO 3 ). For example, electrochemical dissolution of the Cu-Zn recast is accomplished at 1.2 V cell potential using a 20% nitric solution and an exposure time of 4 h. The use of a nitric acid bath was specifically chosen since it’s chemically compatible and will not degrade the host alloy or the component. In sum, an electrochemically driven dissolution process can be tailored to remove of the recast contamination without affecting the integrity of the host component structure and its dimensional tolerances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Wear Performance of incoloy 800HT and inconel 617 in various surface conditions for high-temperature gas-cooled reactor components

Incoloy™ 800HT and Inconel™ 617 are primary candidate structural materials for high-temperature gas-cooled reactors (HTGRs). Impurities (e.g., H 2 O, CH 4 ) in the coolant induce corrosion reactions that affect tribological behavior. We investigate the high-temperature tribological performance of the alloys under surface conditions including: conditioned in H 2 O-containing helium at elevated temperatures, hardened via the carbon-diffusion Kolsterising® treatment, and conditioned after hardening. Initial friction coefficients and volume removed serve as metrics for wear performance. In this work, we find that wear mechanisms including scuffing, glaze-oxide formation, and oxide-layer wear and break-through are governed by surface hardness, chemistry, and applied load. The formation of a glaze-oxide layer is achieved with an oxide of sufficient mechanical integrity if the oxide-substrate interface is strong and the load is low.

42 ENGINEERING↗
NASA NTRS1984

Chromium boron surfaced nickel-iron base alloys

Chromium boron diffusion coatings on nickel iron alloys uniquely provide them with improvement in high cycle fatigue strength (up to 30%) and erosion resistance (up to 15 times), compared to uncoated alloy. The diffused chromium layer extends in two essential concentration zones to a total depth of about 40.times.10.sup.-6 m, while the succeeding boron layer is limited to 50-90% of the depth of the richest Cr layer nearest the surface. Both coatings are applied using conventional pack diffusion processes.

Rashid, James M.↗
NASA NTRS1982

Tribological properties of amorphous alloys and the role of surfaces in abrasive wear of materials

The research approach undertaken by the authors relative to the subject, and examples of results from the authors are reviewed. The studies include programs in adhesion, friction, and various wear mechanisms (adhesive and abrasive wear). The materials which have been studied include such ceramic and metallic materials as silicon carbide, ferrites, diamond, and amorphous alloys.

Miyoshi, K.↗
DOE OSTI2023

Method of coating high atomic number metals onto oxygen or hydroxyl rich surfaces

Methods for making layered materials and layered materials including high atomic number metals and metal alloys adhered to surfaces are provided. Such surfaces may be oxygen or hydroxyl rich surfaces. Certain methods include depositing a tie down layer of a first metal or metal alloy particles onto a first surface of base material and depositing a high atomic number metal or metal alloy layer onto the first surface after depositing the tie down layer, wherein particles comprising the high atomic number metal or metal alloy layer have a higher atomic number than the first metal or metal alloy particles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Examination of Intergranular Crack on SC0234

The microstructure of the SC0234 weld was evaluated per DA-SPEC-01067, ''General Purpose Heat Source (GPHS) Plutonium-238 Dioxide Fueled Clad Product Specification'' and it was determined that the weld microstructure conformed to the quality requirements. During the examination of weld cross section, the metallographic analysis revealed the presence of a surface crack. Prior visual examination per RPS-TA55-303 had not revealed the crack, nor did the surface photography performed per RPS-TA55-302. The presence of the crack does not violate any of the product specifications called out on DA-SPEC-01067. Although there is a well-documented history of weld hot crack susceptibility in the early development of the DOP-26 iridium alloy, a surface crack such as this had not been documented during welding at Los Alamos. In the interest of better understanding the cause; the product engineer/program recommended further examination of the crack. This report discusses the examination of the crack found in the weld cross section of simulant clad SC0234. Metallography, Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy techniques (EDS) where used in the analysis of the crack and the surrounding weld microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electronic, magnetic, and optical properties of bulk and (1 1 1)-surfaces of CoMnZnSi quaternary Heusler alloy

The structural stability, electronic structure, and magnetic and optical properties of CoMnZnSi quaternary Heusler alloy (QHA) in the bulk and (1 1 1)-slab forms have been investigated by performing density functional theory (DFT) calculations. Formation and cohesive energies, and elastic constants confirm that the bulk CoMnZnSi is chemically and mechanically stable at an equilibrium lattice parameter of 5.81 Å. The calculated elastic constants also indicate that this QHA has ductile and anisotropic features. We investigate and discuss the bonding behavior from charge density distribution and density of states. Furthermore, these calculations in the bulk phase show a perfect half-metallic behavior with an integer value of magnetic moment (4 µB) and a large spin-flip gap of 0.39 eV. On the other hand, the Co (1 1 1) and Si (1 1 1)-slabs exhibit semi-metallic nature at the Fermi level. These results indicate that CoMnZnSi qualifies for spintronic applications. In the bulk and Co (1 1 1), Zn (1 1 1), and Si (1 1 1)-surfaces, the magnetic moment of Co and Mn atoms are ferromagnetically aligned, while the ferrimagnetic alignment of Co with Mn has been found in Mn (1 1 1)-surface. We also investigate the optimal conductivity, dielectric functions, reflectivity, absorption coefficient, refractive index, and loss function to understand the underlying optical properties of this alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elevated temperature mechanical properties of Inconel 617 surface oxide using nanoindentation

Inconel 617 is a principal candidate material for helium gas cooled very-high-temperature reactors with outlet temperatures of 700–950 °C. Recent findings showed that this alloy develops unique surface oxide layers especially at high temperature (HT) helium environment with distinctive wear, friction and contact properties. This study investigates the elevated temperature mechanical properties of Inconel 617 top surface layers aged in HT helium environment. Nanoindentation technique is used to obtain load-displacement graphs of the alloy top surface oxide in temperatures ranging from 25 °C up to 600 °C. In addition, using finite element analysis along with an iterative regression technique, a semi-numerical method is developed to further measure and quantify the material parameters and, in particular, time-independent and creep characteristics of the oxide. Although Young's modulus of the oxide is found to be relatively close to the bulk for the tested temperatures, the yield strength and hardness, in comparison to the bulk material, increase significantly as the material is oxidized after aging. The oxide exhibits significant softening as the temperature increases to 600 °C. Unlike the bulk material, diffusion through the grains is found to be the dominant creep mechanism for the oxide. Considerable difference between the mechanical properties of the oxide and the bulk material shows the need for accurate measurements of near surface mechanical properties, if reliable predictive contact and tribological models are sought at elevated temperatures.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Low-pressure oxidation of Cb-1Zr alloy.

Resistively heated strip specimens of Cb-1Zr alloy were exposed at 927 C in a vacuum chamber at various levels of total pressure in the 1-microtorr range and at various oxygen partial pressures in the .1-microtorr range. Oxygen reaction rates (sticking probabilities) were found to depend on whether or not the specimens were annealed immediately before the test exposure. It is shown that a normally undetectable oxide film exists on the Cb-1Zr surface as a result of oxidation by ambient air, and this film reduces the sticking probability as compared with a clean metal surface. The alloy is considerably strengthened by addition of oxygen to a level of about 6000 ppm, while still maintaining reasonably good room temperature ductility.

Lyon, T. F.↗
DOE OSTI2024

Environmental Compatibility Issues for Ni-Based Alloys in Direct-Fired Supercritical CO2 Power Cycles

Direct-fired supercritical CO2 (sCO2) power cycles offer potential for high-efficiency power generation from natural gas and other fossil fuels with built-in carbon capture. Ni-based superalloys are the leading candidates for the hottest portions of these systems, where they must endure long-term exposure to high-temperature, high-pressure, high-velocity, impure CO2-rich environments. Herein we describe results of various experimental testing campaigns conduced at NETL showing that under such conditions, several simultaneously occurring degradation modes may be active including surface oxidation, alloy carburization, and oxide volatilization. It will be shown that the rates of degradation can be strongly affected by the alloy composition, impurities in the CO2, manufacturing method (wrought vs additive), and other factors. The influence of these factors in controlling alloy degradation are discussed in the context of potential compatibility issues for components in real sCO2 systems, such as compact heat exchangers. Finally, as a potential remedial measure, ongoing work involving protective coatings suitable for complex geometries is presented.

alloy oxidation↗
DOE OSTI2020

Oxygen Adsorption, Subsurface Oxygen Layer Formation and Reaction with Hydrogen on Surfaces of a Pt–Rh Alloy Nanocrystal

The oxygen adsorption and its catalytic reaction with hydrogen on Pt–Rh single crystals were studied at the nanoscale by Field Emission Microscopy (FEM) and Field Ion Microscopy (FIM) techniques at 700 K. Both FEM and FIM use samples prepared as sharp tips, apexes of which mimic a single nanoparticle of catalyst considering their similar size and morphology. Oxygen adsorption on Pt-17.4 at.%Rh samples leads to the formation of subsurface oxygen, which is manifested in the field emission (FE) patterns: for O2 exposure of ~3 Langmuir (L), {113} planes appear bright in the emission pattern, while for higher oxygen doses, i.e. 84 L, the bright regions correspond to the high index planes between the {012} and {011} planes. Formation of subsurface oxygen is probably accompanied by a surface reconstruction of the nanocrystal. The subsurface oxygen can be effectively reacted off by subsequent exposure of the sample to hydrogen gas at 700 K. The hydrogenation reaction was observed as a sudden, eruptive change of the brightness seen on the FE pattern. This reaction resulted in the recovery of the initial field emission pattern characteristic of a clean tip, with {012} facets being the most visible. It was shown that the oxygen accumulation-reduction process is completely reversible. The obtained results indicate that the presence of subsurface species must be considered in the description of reactive processes on Pt–Rh catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Metallic Pd–Cu Alloy Phases Drive Selective Heterogeneous Electrochemical Ketonization of 1-Butene

Electrification of 2-butanone synthesis via ketonization of 1-butene offers a viable pathway to reduce emissions associated with its production as a commodity chemical and enhance its prospects as a clean carbon-based synthetic fuel. However, the direct electrochemical ketonization of alkenes remains underexplored, with previous studies largely limited to epoxides and glycols. Herein, we report an electrochemical heterogeneous system optimized for 1-butene ketonization, converting 1-butene to 2- butanone using a bimetallic PdCu catalyst in aqueous electrolytes. The system achieves a Faradaic efficiency of 20% and a partial current density of 0.6 mA/cm 2 at 1.8 V RHE . In comparison to monometallic Pd and oxidized PdCu analogs, the PdCu catalyst doubles the ketonization Faradaic efficiency and quadruples the production rate. Postelectrolysis characterization reveals that PdCu preserves the surface metallic alloy phase under anodic polarization, which likely accounts for the enhanced ketonization activity. This work demonstrates the significance of the Pd−Cu speciation dynamics and provides a framework for designing selective electrocatalysts for alkene ketonization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Emergence of local scaling relations in adsorption energies on high-entropy alloys

Alloying has been proposed to circumvent scaling relations between the adsorption energies thus allowing for the complete optimization of multistep reactions. Herein the fidelity of scaling rules on high-entropy alloy (HEA) surfaces is assessed focusing on hydrogen-containing molecules, *AH x for A = C and N (x = 0, 1, 2, 3), A = S (x = 0, 1, 2) and A = O (x = 0, 1). Using an adsorbate- and site-specific deep learning model to rapidly compute the adsorption energies on CoMoFeNiCu HEA surfaces, the energies of *AH x and *A are shown to be linearly correlated if *A and *AH x have identical adsorption site symmetry. However, a local linear dependence emerges between the configuration-averaged adsorption energies irrespective of the site symmetry. Although these correlations represent a weaker form of the scaling relationships, they are sufficient to prohibit the optimization of multistep reactions. The underpinning of this behavior is twofold (1) the nearsightedness principle and (2) the narrow distribution of the adsorption energies around the mean-field value. While the nearsightedness is general for all electronic systems, the second criterion applies in HEAs with relatively strong reactive elements. The present findings strongly suggest that alloys may not generally enable the breaking of scaling relationships.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Uncovering electronic and geometric descriptors of chemical activity for metal alloys and oxides using unsupervised machine learning

Here, we show that unsupervised machine learning (ML) using principal component analysis (PCA) provides a straightforward pathway for developing accurate and interpretable electronic-structure descriptors of the chemical and catalytic properties of materials. We demonstrate the approach by finding chemisorption descriptors for metal alloys and surface oxygens on metals and metal oxides. In both cases, the principal component (PC) descriptors yield ML models that predict the material’s chemical properties with competitive accuracy compared to ML models built using established descriptors. Importantly, interpreting the electronic-structure patterns captured by each PC descriptor via signal reconstruction suggests potential design motifs for future electronic-structure descriptor design and allows us to identify links between a material’s geometric and catalytic properties. Ultimately, we show that the unsupervised ML approach provides a route to find electronic-structure descriptors of the catalytic properties of materials that readily connect to geometric structure and composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Sn-Based Alloys Synthesized in an Ionic Liquid at Room Temperature: Cu6Sn5 as a Case Study

Sn-based alloys are increasingly investigated owing to possible electronic/structural modulations of interest for electrocatalysis and energy storage applications. Here, we report on the use of a chemical system consisting of an ionic liquid (1-ethyl-3- methylimidazolium bis(trifluoromethanesulfonyl)imide: [EMIm(+)][TFSI-]) and Sn-based precursor Sn(TFSI)(2) both featuring similar anionic groups. This strategy increases the solubility of the cationic precursor in the IL and avoids the formation of side-products during the precipitation of Sn-nanoparticles formed upon reaction with a reducing agent (NaBH4). Using NMR relaxometry, we further established that these nanoparticles are stabilized by specific interactions with the cationic group of the IL. Targeting the composition Cu6Sn5, we further demonstrated that this approach can be used to prepare Sn-based alloys which could not be prepared using conventional chloride-based precursors.

cyclic voltammetry↗
DOE OSTI2022

Co-extrusion of dissimilar Al alloys via shear assisted processing and extrusion

Cladded tubes are generally used where two distinct properties are required at the outer and inner part of a tube, for instance, strength and corrosion resistance. In this investigation, shear assisted processing and extrusion (ShAPE) was employed to fabricate bi-metallic tubes from 1100 and 7075, and 1100 and 2024 dissimilar Al alloy combinations. Surface defect-free bi-metallic tubes were fabricated via the ShAPE process. Detailed microstructural characterization of the interface and various locations of the cladded tubes were carried out using light and scanning electron microscopy techniques. A defect-free, metallurgically bonded interface between the cladded layer and high strength Al (7075 and 2024 Al) was observed. Furthermore, hardness and tensile properties of the cladded ShAPE tubes were examined in the as-extruded conditions.

Komarasamy, Mageshwari↗