Search NASA⌕ Search

SEARCH · Search NASA

Results for “tensile fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deformation and fracture behavior of a laser powder bed fusion processed stainless steel: In situ synchrotron x-ray computed microtomography study

Tensile plastic deformation and fracture behavior of a laser powder bed fusion processed 316L stainless steel alloy was investigated in situ using high-resolution synchrotron x-ray computed microtomography (sXCT). Three different cases were studied: (1) specimen A1, near full-density with initial porosity of 0.04%, (2) specimen B1, initial lack-of-fusion (LOF) porosity of about 3% with the major axis of defects aligned nearly perpendicular to the tensile loading direction (LD), and (3) specimen B, similar to B1 but with the major axis of LOF defects aligned nearly parallel to LD. The effects of type, density, and orientation of defects in as-printed samples on plastic deformation and failure modes were studied by analyzing sXCT image sequences and quantitative defect properties. Specifically, the evolutions of porosity, size, aspect ratio, and angle of gas pores and LOF defects were characterized as a function of applied strain. Moreover, interactions between as-printed defects and deformation-induced crack propagation were investigated. The tensile behavior of specimen A1 was comparable to that of a commercial wrought plate. Furthermore, the quantitative in-situ sXCT results showed a void-growth phenomenon in A1 but without noticeable coalescence, resulting in a ductile cup-cone failure. Specimen B1 showed damage-driven brittle failure with limited plasticity due to early and rapid propagation of open voids. On the other hand, specimen B, with a similar amount of LOF defects as B1, showed deceivingly strong and ductile tensile behavior similar to A1 without any major crack propagations due to the favorable orientation relationship between LOF defects and the LD.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elastic Properties and Deformation Mechanisms in the van der Waals Single-Crystalline Indium Selenide

The bulk van der Waals (vdW) single-crystalline indium selenide (β-InSe) displays exceptional plasticity in a layered crystalline form at both micro- and macroscale. However, the nanoscale origin of plasticity remains unclear. Herein, an atomic-level study on the deformation mechanisms of InSe by using first-principles calculations is reported. Remarkable anisotropic elasticity is observed in the vdW InSe layered crystal, and the stiffness is dramatically softened because of the vdW gap in the layered structure. The simulations capture the distinct fracture modes in the uniaxial tensile deformation, depending on the loading directions—brittle fracture in the [100] and [110] directions while ductile failure in the [001] direction. The InSe layered crystal structure exhibits superplastic deformability under uniaxial compression. Different transition pathways, including interlayer tangling, amorphization, and cross-linking, are tracked along respective deformation directions. The unprecedented plasticity of InSe layered crystals can be attributed to the phase transition coupled with interlayer gliding and cross-layer dislocation slipping. Here, this study deepens our understanding of the deformation mechanisms of layered materials at the atomistic level and provides insights into tailoring material properties for low-dimensional material design based on its deformation mechanisms.

2D materials↗
NASA NTRS1985

Mechanical behavior of 18 Ni 200 grade maraging steel at cryogenic temperatures

A comprehensive study was conducted to characterize the mechanical behavior of 18 Ni 200 grade maraging steel for cryogenic applications in the National Transonic Facility. Tensile, fatigue, impact, and fracture toughness properties were determined at room and cryogenic temperatures. Experimental variables included product form, specimen orientation, and variation in metallurgical condition accomplished with a grain refining heat treatment. Room temperature tensile yield strength was approximately 200 ksi, while the yield strength at -275 F was approximately 260 ksi. Charpy V-notch energy absorption values and fracture toughness values of 18 Ni steel were found to be dependent on temperature, product form, orientation, and metallurgical condition. Fracture toughness values ranged from 80 to 113 ksi-sq rt in. at room temperature and from 67 to 90 ksi-sq rt in. at -275 F. The results of this study indicate that 18 Ni 200 grade maraging steel exceeds the strength criterion of 150 ksi minimum yield strength for use in cryogenic wind tunnel models but is marginal with respect to the 85 ksi sq rt in fracture toughness criterion at -275 F.

Wagner, J. A.↗
DOE OSTI2024

Investigating Material Properties of Subsurface Rock Formations Modified by Engineering Mineral Precipitation (Final Scientific and Technical Report)

Montana State University’s (MSU) Energy Research Institute (ERI), in collaboration with the Center for Biofilm Engineering (CBE) and the Department of Civil Engineering (CE), has conducted a long‐term research program aimed at developing a novel cementing agent to address wellbore integrity and reduce the unwanted upward migration of fluids and greenhouse gases from the subsurface. The primary technology developed through this research program is known as ureolysis‐induced calcite precipitation (UICP), which harnesses bio‐chemical processes to precipitate calcium carbonate (CaCO 3 ). The same general process can also be called microbially-induced calcium carbonate precipitation (MICP) when microbes provide the process-catalyzing urease enzyme. Both terms are used in this report. Results have conclusively demonstrated that, if properly controlled, UICP can successfully seal fractures, high permeability zones, and compromised cement in the vicinity of wellbores and in nearby caprock. This technology has been successfully deployed to mitigate annular leakage in two test wells and over sixty commercial wells with a 100% success rate. This success in downhole deployment generates consideration of other subsurface applications where UICP could provide benefit to the energy sector, such as shale property modification for unconventional oil and gas recovery. The focus of this research project was to investigate fundamental material and mechanical properties of select shale cores and analyze how these properties change due to engineered mineral precipitation with the intent to control these properties to achieve a range of engineering objectives. Ultimately, the project aim was to identify valuable new areas where application of UICP might contribute to national energy security and environmental protection. The research workplan coupled UICP treatment of core samples, nuclear magnetic resonance (NMR) characterization, and mechanical strength testing at MSU with advanced X‐Ray micro-computed tomography (μCT) imaging and numerical modeling performed by collaborators at two national laboratories, the National Energy Technology Laboratory (NETL) and Lawrence Berkeley National Laboratory (LBNL). Experimental results are useful to inform geo-mechanical models which could be applied to predict mineralized rock formation behavior at field scale. Our findings suggest that NMR and μCT methods to detect and quantify biomineral formation in shale fractures are complementary and consistent with each other. Either could be used to estimate the volume of new mineral formed by UICP in shale fractures. The use of surfactants and guar gum to enhance biomineral precipitation in shale fractures merits further research. UICP can, under some conditions, increase the tensile strength of sealed shale fractures beyond that of the intact shale. These findings demonstrate that continued research in this area may be valuable to understanding and improving shale resource recovery techniques.

58 GEOSCIENCES↗
NASA NTRS1990

Load biaxiality and fracture - Synthesis and summary

The question of load biaxiality strongly affecting almost all of the characteristics of brittle fracture behavior of a cracked body is investigated. Results of research published piecemeal over the years by the authors have shown that the stress and displacement fields, the elastic strain energy density, and the maximum shear stress near the crack tip are all altered by loads applied parallel to the crack, as are the angle of initial crack extension, the strain energy of the entire body, the fracture load, and the rate of fatigue crack growth. A synthesis and summary of this research is presented showing the shortcomings inherent in both Griffith's global energy rate theory for crack instability and Irwin's local crack-tip stress intensity theory for fracture toughness. In both theories only the tensile load perpendicular to the crack influences fracture behavior of the body.

Eftis, J.↗
NASA NTRS1993

Combined mode I and mode II fracture of monolithic ceramics

The mode I, mode II, and combined mode I-mode II fracture behaviors of a coarse-grained silicon nitride, a fine-grained silicon nitride, and an alumina were investigated. These ceramics were fractured from two types of fracture initiating flaws: small surface flaws and large single edge precracks. The small surface flaws were introduced by Knoop indentation in flexural samples at various angles to the tensile stress direction and fractured in four-point bending. The samples with large precracks were fractured in the asymmetric four-point-bend geometry. The mixed-mode fracture toughness values obtained from the two flaw configurations were in good agreement with each other. All three ceramics displayed very similar mixed-mode fracture behavior, although their microstructures were not similar. Comparison of experimental data to mixed-mode fracture theories revealed that the minimum strain energy density theory best described the mixed-mode fracture behavior of all three ceramics.

Tikare, Veena↗
DOE OSTI2024

Microstructure and mechanical properties of ultrasonic spot welding of AA7075-T6 and A380 casting aluminum alloy

Ultrasonic spot welding (USW) was employed to join AA7075-T6 and casting Al alloy A380. Under a constant welding power, the influence of the welding time duration (from 1 s to 3 s) on peak temperature, microstructure, hardness, and mechanical strength of the joints were studied. It was found that the peak temperature increased with welding time. A sound solid-state metallurgical bonding was obtained at the joint interface. The cracks occurred at the edge of the joints were eventually eliminated as the welding time increased. A layer of refined grains formed in A380 adjacent to the bonding line. Further, hardness reduction occurred in AA7075 at the joint interface and the degree of hardness reduction and the volume increased with the peak temperature. By increasing welding time, lap shear tensile tests show that the peak load increased from 5.3 kN to 6.55 kN. The corresponding interfacial shear strength ranged from 96.29 MPa to 99.72 MPa, lower than the shear strength of both base materials (331 MPa for AA7075 and 185 MPa for A380). All joint samples exhibited interfacial fracture after lap shear tensile testing, with a thin layer of A380 remnant attached to AA7075 at the center of the fractured surface.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Predicted Fracture Tendency of Naturally Occurring Aluminum Surface Coatings under Tensile Loading

Naturally occurring coatings on aluminum metal, such as its oxide or hydroxide, serve to protect the material from corrosion. Understanding the conditions under which these coatings mechanically fail is therefore expected to be an important aspect of predictive models for aluminum component lifetimes. To this end, we develop and apply a molecular dynamics (MD) modeling framework for conducting tension tests that is capable of isolating factors governing the mechanical strength as a function of coating chemistry, defect morphology, and variables associated with the loading path. We consider two representative materials, including γ-Al 2 O 3 and γ-Al(OH) 3 (i.e., oxide and hydroxide), both of which form readily as aluminum surface coatings. Our results indicate that defects have a significant bearing on the strength of aluminum oxide, with grain boundaries serving to reduce the strain at failure from ε zz = 0.300 to 0.219, relative to perfect single crystal. Our simulations also predict that porosity lowers the elastic stiffness and yield strength of the oxide. Relative to perfect crystal, we find porosity factors of 5%, 10% and 20% decrease the yield stress by 26%, 36% and 53%, respectively. MD predicts that perfect hydroxide and oxide single crystal have respective strains at failure of 0.08 and 0.31 under tensile uniaxial strain loading, and that the corresponding yield stresses are respectively 1.6 and 11.1 GPa. These data indicate that the hydroxide is substantially more susceptible to mechanical failure than the oxide. Our results, coupled with literature findings that indicate hot and humid conditions favor formation of hydroxide and defective oxide coatings, indicate the potential for a complicated dependence of aluminum corrosion susceptibility and stress corrosion cracking on aging history.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Computing Reliabilities Of Ceramic Components

CARES/PC computer program performs statistical analysis of data obtained from fracture of simple, uniaxial tensile or flexural specimens of ceramics and estimates Weibull and Batdorf material parameters from these data. CARES/PC is subset of Ceramics Analysis and Reliability Evaluation of Structures (CARES) program (LEW-15168), which calculates fast-fracture reliabilities or failure probabilities of ceramic components by use of Batdorf and Weibull models to describe effects of multiaxial stress states on strengths of materials. CARES/PC written and compiled with the Microsoft FORTRAN v5.0 compiler.

Szatmary, S. A.↗
NASA NTRS1978

Microstructure and mechanical properties of quenched and tempered 300M steel

Type 300M steel, which is being used for the landing gear on the space shuttle orbiter, was subjected to a wide range of quenched and tempered heat treatments. The plane-strain fracture toughness and the tensile ultimate and yield strengths were evaluated. Cryogenic mechanical properties were obtained for conventionally heat-treated steel. The microstructure of all heat-treated test coupons was studied both optically and by transmission electron microscopy. Fracture surfaces were studied by means of scanning electron microscopy. Results indicate that substantial improvement in toughness with no loss in strength can be accomplished in quenched and tempered steel by austenitizing at 1255 K or higher. Low fracture toughness in conventionally austenitized 300M steel (1144 K) appears to be caused by undissolved precipitates, seen both in the submicrostructure and on the fracture surface, which promote failure by quasi-cleavage. The precipitates appeared to dissolve in the range 1200 to 1255 K.

Youngblood, J. L.↗
NASA NTRS1996

Prediction of Composite Laminate Fracture: Micromechanics and Progressive Fracture

This report describes an investigation to predict first-ply failure and final fracture in selected composite laminates subjected to inplane loads. The laminates were composed of glass fiber and graphite fibers in epoxy matrices. Failure envelopes based on first-ply failure and laminate fracture were generated for combined loading of these laminates. Predictions were evaluated by micromechanics-based theory and progressive fracture. The results show that, for most cases, combined tensile loading significantly enhanced the laminate fracture stress in comparison to the uniaxial loading.

Gotsis, P. K.↗
NASA NTRS1977

Creep degradation in oxide-dispersion-strengthened alloys

Oxide dispersion strengthened Ni-base alloys in wrought bar form are studied for creep degradation effects similar to those found in thin gage sheet. The bar products evaluated included ODS-Ni, ODS-NiCr, and three types of advanced ODS-NiCrAl alloys. Tensile test specimens were exposed to creep at various stress levels at 1365 K and then tensile tested at room temperature. Low residual tensile properties, change in fracture mode, the appearance of dispersoid-free bands, grain boundary cavitation, and internal oxidation in the microstructure were interpreted as creep degradation effects. This work showed that many ODS alloys are subject to creep damage. Degradation of tensile properties occurred after very small amounts of creep strain, ductility being the most sensitive property. All the ODS alloys which were creep damaged possessed a large grain size. Creep damage appears to have been due to diffusional creep which produced dispersoid-free bands around boundaries acting as vacancy sources. Low angle and possibly twin boundaries acted as vacancy sources.

Whittenberger, J. D.↗
DOE OSTI2020

Modeling Graphite Behavior (Fracture and Oxidation)

Purpose of this work Oxidation modeling Oxidation of full-scale components Local properties in oxidized components Graphite fracture strength Phase field fracture modeling Microstructurally informed fracture model IG-110 tensile results and comparison to experiment Work in progress and future work

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1973

Plastic intensity factors for cracked plates subjected to biaxial loading

An elastic-plastic analysis is performed for an infinite plate under plane stress conditions which contains a finite line crack and is subjected to biaxial loading. In the large scale yielding range, the amplitude of the dominant singularity at the crack tip, the plastic stress (or strain) intensity factor, is found to depend on the magnitude of loading parallel to the crack direction. The predicted value for the fracture initiation stress which is based on a plastic intensity factor fracture criterion, increases under lateral, tensile loading. Compressive loading parallel to the crack has the opposite effect on the fracture initiation stress.

Hilton, P. D.↗
NASA NTRS1989

Notch effects on room temperature tensile and bend properties of Ni3Al and Ni3Al+B

The notched mechanical properties of Ni3Al and Ni3Al+B prepared by powder metallurgy techniques have been determined in both tension and bending at room temperature. Tensile tests performed using double-notched specimens containing relatively blunt notches produced intergranular fracture in both Ni3Al and Ni3Al+B, with evidence of fracture initiating in an intergranular manner ahead of the blunt notch in both cases. Estimates of notched fracture toughness from bend tests and of local grain boundary fracture stress from the notched tensile tests suggest an increase in these values with boron addition.

Khadkikar, P. S.↗
NASA NTRS1974

The effect of microstructure on the fracture toughness of titanium alloys

The microstructure of the alpha titanium alloy Ti-5Al-2.5Sn and the metastable beta titanium alloy Beta 3 was examined. The material was from normal and extra low interstitial grade plates which were either air-cooled or furnace-cooled from an annealing treatment. Beta 3 was studied in alpha-aged and omega-aged plates which were heat treated to similar strength levels. Tensile and plane strain fracture toughness tests were conducted at room temperature on the alpha-aged material. The microstructure and fracture mechanisms of alloys were studied using optical metallography, electron microscopy, microprobe analyses, and texture pole figures. Future experiments are described.

Vanstone, R. H.↗