Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal aging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Quantifying Properties for a Mechanistic, Predictive Understanding of Aqueous Impact on Aging of Medium and Low Voltage AC and DC Cabling in Nuclear Power Plants

To address the gap in knowledge in understanding degradation in relevant service conditions, this project aimed to develop a mechanistic, predictive model of medium and low voltage cable failure based on the primary environmental degradation parameters of aqueous immersion time, temperature, and the oxidation extent. To do so, we took a two-fold approach toward evaluating degradation as related to the aqueous condition. First, we evaluated the chemical, mechanical, and electrical properties of polymers that comprise the cabling insulation under varied aqueous conditions at different temperatures. Secondly, we evaluated the performance of insulation materials under similar accelerated aging conditions in addition to the dielectric breakdown of the cabling under submersion conditions. Thermal oxidation and immersion of LDPE thin films were done using a Parr vessel and the extent of oxidation was monitored using the carbonyl index from ATR-FTIR spectrum, a ratio quantifying the carbonyl functionality produced on the LDPE film surface. Increasing the temperature, oxidation time, and oxygen pressure increased the water-vapor permeability and the carbonyl content. Thermogravimetric analysis of the films confirmed that there is indeed an initial weight loss of the smaller molecular weight molecules and volatiles. At higher temperatures, there is a secondary mass loss. Up to 70°C, the mass loss curves were similar until 80°C, when the aged films decreased at a much greater rate with respect to increasing temperature. This was seen in the 10, 50, 90% weight loss temperatures. The mechanical properties of sheet PP and HDPE as well as injection molded LDPE, HDPE, HDPP dog bones were plotted with respect to the time spent in the Parr vessel during thermal oxidation. For the sheet PP and HDPE, the UTS and the modulus of elasticity decreased while the elongation increased. The injection-molded LDPE, HDPE, and HDPP dog bones experienced a similar trend where the changes in the properties were within experimental uncertainty. This analysis of LDPE in dry and immersive oxygen-rich environments is an important baseline for future experiments looking at other degradation mechanisms. A predictive aging model for low-density polyethylene insulative cable housings was developed. This model revealed a combination of physical and chemical processes which lead to an increase in permeability and a decrease in strength of the insulator. In creating this predictive model, a gap of knowledge in the literature was revealed in two areas: understanding how the crystallinity of a polymer changes with time and visualizing the predicted pores formed through the insulator which leads to failure. Developing and using an adapted ATR-FTIR method, crystallinity was monitored and compared to bulk crystallinity found via DSC. Inhomogeneity in crystallinity changes were observed but the FTIR method but was found to be less reliable. Pore visualization was found utilizing electrical impedance spectroscopy saturated aged polyethylene films with synthesized citrate-capped gold nanoparticles, and chloroauric acid precursor. results indicate a decreasing impedance of the polyethylene films caused by the transport of ions through the film. SEM imaging was then performed for elemental analysis of the films and counter electrodes for the presence of ions. Chloride and gold ions were detected; however, no nanoparticles were found. This gives an estimated pore size of at least 0.3 nm through the aged film. Cyclic submergence of polyethylene and polypropylene in aqueous solutions of copper sulfate and Harrison’s solution were examined. It was discovered that aging in these mixed conditions and at 90°C did cause a small, yet significant increase to tensile strength for both unaged polyethylene and polypropylene. The PE and PP in cycled and submerged conditions did not have tensile strengths significantly different from dry-aged after 16 weeks. For both solutions, it was determined that capacitance increases with both water tree depth and cable temperature and is relatively independent of changing water tree AR. As for resistance, there is no apparent change between depth percentages of 10 and 80 for both solutions. This is because the water tree has not yet entered the conductor and thus there is no shorting current flowing through the tree yet. Between 80 and 100% water tree depth, it is observed that for both solutions there is a rapid decrease in resistance because the tree is now impacting the conductor shield and allowing shorting current to flow through it. The relationship between resistance and temperature was found to be inversed. As temperature increases, resistance decreases for both water tree solutions with distilled water having the most apparent difference across the range of temperatures simulated. With regards to water tree AR, resistance was found to be relatively independent at depth percentages of 10, 50, and 70, but there was some relationship at 100% depth for both solutions. At this depth, as water tree AR increased, resistance was found to also increase. Through the examination of voltage and electric field distribution plots, it was confirmed for EPR cables that increasing water tree depth leads to increasing distortion. The increase in shorting current at 100% depth for aqueous copper sulfate compared to distilled water was also visualized. Lastly, the relationship between shorting current and temperature for narrow water trees was visualized and validated using the distribution plots. This study has led to a better understanding of the effect of cable temperature, water tree solution, and geometry of the tree region on cable degradation. Furthermore, this study has documented simulation results of water tree degradation in EPR MV cables, which had been previously lacking in information. Future work in this area will add frequency into the mix and examine what effect it has on the rate of cable degradation as a result of water treeing. To compliment the work being carried by UMD on different polymer chemistries, harvested medium voltage (MV) cables were selected for accelerated aging study at ORNL. These medium voltage cables are representative of the vintages and materials that are currently in use at existing nuclear power plants (NPPs). These cables were immersed in water at 90°C and energized for a period of two years at elevated voltage. Partial discharge was measured during this period of time to track potential degradation. Unfortunately, due to the absence of failure, the extent of integration between the UMD techniques and the harvested MV insulation was limited. However, based on the findings and from the UMD research in the previous sections on polyethylene and polypropylene, follow-on characterization for harvested MV cable insulation should focus on sample preparation to take advantage of the UMD techniques to better understand mechanistic degradation in MV cable insulations. This would include: 1.) Utilization of solutions and impedance measurement insulation to track permeability in harvested and accelerated aging insulation samples, 2.) Adaptation of gold nanoparticle synthesis for electrical impedance spectroscopy with supporting SEM characterization to study pore formation in harvested and accelerated aged insulation samples, & 3.) ATR-FTIR crystallinity with multiple temperature dependent harvested MV cable insulation under different air and submerged accelerated aging. In addition, low voltage dielectric spectroscopy and high voltage dissipation factor, tan δ, could be implemented as a condition monitoring tool for harvested MV cable insulation in submerged environments.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2026

Assess The Water Resistance And Thermal Performance Of Pre-flashing Methods When Adding Continuous Insulation During Re-siding (AIRS)

Retrofitting existing buildings by adding continuous insulation during re-siding projects has become a popular method for enhancing energy efficiency, especially given the aging building stock and stricter energy codes. When properly integrated with existing window systems, continuous insulation can significantly improve thermal performance, but it also presents challenges related to water resistance and building envelope integrity. Research indicates that the interface between windows and wall assemblies is critical as improper installation or sealing can lead to water intrusion, materials deterioration, and energy loss. Moreover, studies show that fully integrating the windows with the insulation layer can reduce window heat loss by up to 40%, emphasizing the importance of optimizing window placement and sealing during retrofitting to ensure both energy efficiency and structural performance. In this study, we conducted experimental tests to evaluate the water penetration and thermal performance of two window types: an aluminum window with a 2-inch installation fin and a wood window, representing typical mid-20th century designs. Using the Heat, Air, and Humidity (HAM) chamber at Oak Ridge National Laboratory (ORNL), we assessed bulk water penetration and performed COMSOL analysis for thermal flux and examined the effectiveness of different pre-flashing methods, i.e., standard self-adhered flashing tape and high-performance flashing tape with low-expansion foam, to enhance water resistance. The results indicate that applying proper flashing techniques and moisture management strategies can mitigate these risks, improving the overall performance and durability of retrofitted buildings. Additionally, proper sealing during retrofitting is essential, as improper installation can lead to moisture issues that compromise both energy efficiency and structural integrity.

Shen, Zhenglai [ORNL]↗
DOE OSTI2023

Role of Fe in long-range ordered Ni 2 Cr precipitates in Ni-Cr-Fe model alloys during isothermal aging

The precipitation of new phases during long-term service at elevated temperatures is a concern for the thermal stability of engineering alloys. In Ni-Cr-based alloys, e.g., Alloy 690, the formation of long-range ordered Ni 2 Cr causes embrittlement and may impact the lifetime of nuclear power plant components. In this work, we quantify the formation and evolution of Ni 2 Cr precipitation in eleven Ni-Cr-Fe model alloys with 0, 5, 7, and 10wt % Fe contents, and with Ni/Cr atomic ratios of 1.8, 2.0, 2.2, 2.4. These alloys were isothermally aged up to 10,000h at temperatures between 330 and 475°C. The alloys were characterized by synchrotron-based x-ray diffraction and Vickers hardness testing to quantify Ni 2 Cr precipitate size, and the impact of precipitate size on the mechanical properties as a function of Fe content. After 10,000 h of aging at 475°C and 418°C, the formation of Ni 2 Cr was observed in all alloys with 0 and 5wt % Fe. After 10,000h of aging at 418°C, Ni 2 Cr precipitates were also observed in the 7wt % Fe containing Ni/Cr=2.0 sample. Further, no clear evidence of Ni 2 Cr was observed in any of the 10wt % Fe samples at any time and temperature combination. We find that the face-centered cubic matrix lattice contraction and Vickers hardness are correlated with the Ni 2 Cr formation. The greatest change in hardness and lattice contraction occurs in stoichiometric alloys (Ni/Cr=2.0) with 0wt % Fe at 475°C. The rate of change in the material properties for the 5wt % Fe alloys is reduced, however the magnitude of changes is similar to 0wt % Fe alloys. A precipitation hardening model developed for Ni-Cr alloys based on critical resolved shear stress with weakly coupled dislocations shows a clear link between Ni 2 Cr precipitate size and hardness. This trend held across all alloys with Ni 2 Cr formation regardless of Fe concentration. This important structure-property relationship can potentially help define Ni-Cr-Fe-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts mechanical properties as a function of Fe content.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Chemical Mixing Induced by Internal Gravity Waves in Intermediate-mass Stars

Internal gravity waves can cause mixing in the radiative interiors of stars. We study this mixing by introducing tracer particles into 2D hydrodynamic simulations. Following the work of Rogers & McElwaine, we extend our study to different masses (3, 7, and 20 M ⊙ ) and ages (ZAMS, midMS, and TAMS). The diffusion profiles of these models are influenced by various parameters such as the Brunt–Väisälä frequency, density, thermal damping, the geometric effect, and the frequencies of waves contributing to these mixing profiles. We find that the mixing profile changes dramatically across age. In younger stars, we noted that the diffusion coefficient increases toward the surface, whereas in older stars the initial increase in the diffusion profile is followed by a decreasing trend. We also find that mixing is stronger in more massive stars. Hence, future stellar evolution models should include this variation. In order to aid the inclusion of this mixing in 1D stellar evolution models, we determine the dominant waves contributing to these mixing profiles and present a prescription that can be included in 1D models.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Initial Conditions of Planet Formation: Time Constraints from Small Bodies and the Lifetime of Reservoirs in the Solar Protoplanetary Disk

This review explores the timescales of the initial phase of planet formation, from nebular dust (CAIs and chondrules) to planetesimal accretion and differentiation, using evidence from meteorite research. Aluminium-Mg systematics of CAIs indicate either an extended period of CAI formation (∼0.3 Ma) or an initial 26 Al heterogeneity, with evidence supporting a homogeneous 26 Al abundance in the protoplanetary disk. Thermal and aqueous alteration on the parent body can disturb the U-Pb and Al-Mg chronometers in chondrules. Focusing on relatively robust isochron data from plagioclase of pristine (types ≤3.05) chondrites indicates a shift in chondrule formation locations, moving from the inner to the outer disk over time. Ages of basaltic achondrites show that silicate differentiation on small bodies was well underway within the first few million years (Ma) of our solar system. Their age record, however, reveals inconsistencies between different chronometers, partly caused by (i) secondary disturbances due to thermal metamorphism, aqueous alteration, or impacts, (ii) the presence of xenolithic minerals, and (iii) potentially variable initial 26 Al abundances due to disturbances at the mineral scale. Nucleosynthetic isotope data indicate that parent bodies of iron and stony meteorites formed in two distinct regions within the protoplanetary disk: the inner, non-carbonaceous (NC) and the outer, carbonaceous (CC) region. Based on Hf-W chronometry it has been demonstrated that NC and CC parent bodies of magmatic iron meteorites segregated their cores within ∼1–3 Ma after CAI formation, implying that parent body accretion occurred within <1 Ma in both reservoirs. Combining accretion ages with nucleosynthetic data further reveals that, at first order, NC and CC reservoirs in the solar protoplanetary disk were established within 1 Ma and existed over several Ma with limited exchange between them. In the CR chondrite accretion region of the disk, planetary bodies formed over at least 3 Ma, while in most other regions, formation spanned at least 1 Ma, with minimal changes in nucleosynthetic isotope compositions. Aerodynamical size sorting of dust likely introduced or amplified some of these variations.

26Al distribution↗
DOE OSTI2021

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Molecular Dynamics Simulation of Hygroscopic Aging Effects in Epoxy Polymer

The automobile industry is incorporating more lightweight content in car designs to boost fuel-economy. New structural adhesives are needed to mitigate the corrosion and thermal expansion issues associated with joining dissimilar lightweight materials, but adhesive developers lack a fundamental understanding of the chemistry that occurs in the adhesive as the joint ages. In this study, we developed structural adhesive molecular models and applied classical molecular dynamics simulations and density functional theory calculations to gain molecular insights into the influence of water molecules on the properties of epoxy-based adhesives (DGEBA + Jeffamine (JD230)). The simulations were complemented by experimental synthesis and characterization. Our work underscores the impact of water molecules on the local structure of the epoxy network as well as resulting mechanical properties. Water molecules were mainly coordinated with hydroxyls, primary amines and secondary amines, but also weakly coordinated with ether linkages, which were found most probable to be labile. Simulated stress–strain data indicates that increasing the water content deteriorates the mechanical properties. The Young’s modulus decreased by ~ 30% when the water content increased to 3 wt%. We conclude, this integration of molecular-level chemical insights with mechanical property simulations of the hydrated epoxy system and experimental validation holds the promise to advance lightweight joint technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Abstract for CRADA between NETL and Praxair Surface Technologies, Inc. (AGMT-1288)

The National Energy Technology Laboratory (NETL) and Praxair Surface Technologies (Participant) will collaborate in the design and manufacturing of new high-performance thermal barrier coatings (TBCs) for hydrogen gas turbine applications. High-throughput first-principles density functional theory (DFT) calculations will be performed to accelerate novel TBCs discovery with expanded phase field, increased temperature and erosion capabilities, low thermal conductivity, and significant toughness imparted by ferroelastic toughening for the non-transformable tetragonal oxide phase. Down-selected materials will be manufactured using solid state powder processing techniques. Testing will include isothermal aging followed by Raman and x-ray diffraction (XRD) phase analysis, indentation fracture toughness measurements, erosion testing, and thermal conductivity measurements. The collaboration will facilitate the deployment of hydrogen gas turbine technologies that are a key to the decarburization of power generation in the United States.

08 HYDROGEN↗
DOE OSTI2025

Developing the Science Basis for Understanding Polymer Encapsulant Degradation Mechanisms: DuraMAT 2.0 Final Project Report

Polymeric encapsulants are essential materials in photovoltaic modules, protecting sensitive electronics from the environment while providing mechanical integrity to the multilayered assembly. However, these polymeric materials are susceptible to degradation processes driven by the ingress of environmental species, ultraviolet radiation, thermal stresses, and mechanical loading. In this study, we employ a combined atomistic simulation and accelerated aging experimental approach to study the molecular-scale mechanisms of encapsulant degradation. Classical molecular dynamics simulations quantify the diffusion of environmental and degradation species through the polymer matrix, producing composition-specific diffusion coefficients. Reactive simulations characterize activation energy barriers and reaction rate constants for key chemical pathways. In parallel, thermal-desorption analyses coupled with mass spectrometry monitor the emergence and concentration profiles of degradation products under controlled stressor conditions. By integrating simulation and experiment, we establish quantitative correlations between polymer composition, species diffusivity, and chemical reactivity. We anticipate that these relations and quantitative values could serve as high-fidelity inputs to reaction-diffusion models, enabling physics-informed lifetime predictions and guiding the design of more durable encapsulant materials for solar energy applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal stability of additively manufactured austenitic 304L ODS alloy

Thermal stability and high-temperature mechanical properties of a 304L austenitic oxide dispersion strengthened (ODS) alloy manufactured via laser powder bed fusion (LPBF) are examined in this work. Additively manufactured 304L ODS alloy samples were aged at temperatures of 1000, 1100, and 1200 °C for 100 h in an argon atmosphere. Microstructure characterization of LPBF 304L ODS alloy before and after the thermal stability experiments revealed that despite the annihilation of dislocations, induced cellular substructure by the LPBF process was partially retained in the ODS alloy even after aging at 1200 °C. The size of Y-Si-O nanoparticles after aging at 1200 °C increased from 25 to 50 nm. EBSD analysis revealed that nanoparticles retained the microstructure of LPBF 304L ODS and hindered recrystallization and further grain growth. At 600 °C and 800 °C, the yield stress of the 290 and 145 MPa were measured, respectively, which are substantially higher than 113 MPa, and 68 MPa for 304L at the same temperatures. Furthermore, the creep properties of LPBF 304L ODS alloy were evaluated at a temperature of 700 °C under three applied stresses of 70, 85, and 100 MPa yielding a stress exponent (n) of ~7.7; the minimum creep rate at 100 MPa was found to be about two orders of magnitude lower than found in the literature for wrought 304L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of thermal environments on fast charging Li-ion batteries

Battery thermal management systems (BTMSs) are expected to keep the battery temperature at a moderate level (~30 °C) to minimize the thermally exacerbated degradation. However, during fast charging, a strong cooling system is required to restrict the temperature rise of Li-ion batteries (LiBs), which significantly increases the cost and weight of battery packs, and induces a large temperature variation inside the battery. Here, in this work, we find that all these drawbacks could be relieved by allowing LiBs to charge at higher temperatures. Since the fast charging of a LiB only takes a tiny fraction of its lifetime, the aging rate is limited even at a charging temperature of 60 °C. Three types of thermal environments are proposed: kept constant at 30 °C, preheated to 60 °C, and adiabatic fast charging. With an experimentally validated electrochemical-thermal (ECT) coupled model, we explore the interplay between thermal management and the fast-charging performance. It is found that a gradually increasing temperature profile is the best option to balance the lithium plating and thermal management of the battery. Combining adiabatic fast charging with a preheating step, we can achieve minimal cooling need, perfect temperature uniformity within a battery, and fast-charging capability simultaneously.

25 ENERGY STORAGE↗
DOE OSTI2025

Advanced Diagnosis and Accelerated Testing of Balance of System Components for Utility Scale PV Installations: October 1, 2022-September 30, 2024

A study of the durability of PV Balance of System components was performed. Specifically, wire cable jackets and cable connectors were examined within the direct current (DC) PV Power Transmission Chain (PTC). Degraded and failed samples have been obtained from utility PV installations to provide feedback on the degradation modes and the related damage-enabling considerations in today's PV systems. An industry interface group (including system owners, system inspectors, component manufacturers, and test labs) was used to help identify and obtain field-failed samples, for feedback (including samples and experimental design), and to facilitate the subsequent dissemination of the results of this study. Samples were empirically studied using accelerated stress testing with steady-state conditions (cable jackets) in addition to combined-accelerated stress testing (cable jackets, connectors and uncapped connectors). Steady-state accelerated testing has been performed using at least one applied stressor (e.g. UV light) to aid understanding of jacket durability relative to its application. Component- and material-focused failure analysis was conducted to develop an understanding and advise the PV industry. In-depth characterization will be applied selectively to field- and artificially aged-samples, to gain scientific understanding of the structural, chemical, electrical, mechanical, and thermal properties enabling degradation.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Effect of a liquid-type temperature rise inhibitor on cement hydration

A liquid-type temperature rise inhibitor (L-TRI) based on modified sorbitol was developed to solve the thermal cracking issue by modulating the heat release from cement hydration during the early age. Both the exothermic process and phase evolution of cement pastes blended with/without L-TRI were investigated by the combination of isothermal calorimetry, in-situ XRD, ICP-OES and SEM. Also, the adsorption of the L-TRI in the cement paste was identified by total organic carbon analysis. The testing results suggested that the L-TRI affected the heat flow curve in two ways. It prolonged the induction period as a retarding effect. It also reduced the heat flow during the acceleration period and decreased the maximum heat flow as a depressing effect. The retarding effect was mainly caused by the complexation of unabsorbed molecules in the pore solution, and the depressing effect was caused by inhibiting the growth of C-S-H.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comprehensive Battery Safety Risk Evaluation: Aged Cells versus Fresh Cells Upon Mechanical Abusive Loadings

Abstract Despite their wide applications, lithium‐ion batteries (LIBs) have been struggling with their safety risks arising from different lifetime stages. Here, the NCMA pouch cell is taken as an example, and the safety of both fresh and aged cells from three milestone stages, that is, internal short circuit (ISC) triggering risk, ISC mode, and the subsequent thermal runaway (TR) consequence is investigated. By combining mechanical abusive testing and physics‐based models on commercialized cells with various states‐of‐health (SOH) and states‐of‐charge, it is discovered that the ISC triggering delays with the decay of SOH and soft ISC mode will be triggered more frequently, which is mainly due to the mechanical behaviors of the current collectors. The temperature rises and peak temperature during the subsequent TR also become milder for aged cells due to the reduced capacity and deterministic soft ISC process. Results here provide a mechanistic explanation of the safety risk comparison between the fresh and aged cells, offering cornerstone guidance to the evaluation and design of next‐generation safer LIBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Shear Assisted Processing and Extrusion (ShAPE) of Aluminum Alloy 7075, 2024, and Al-12.4TM

The most common aluminum alloys utilized in the aerospace industry are 7075 and 2024 due to their high strength-to-weight ratio compared to advanced high strength steels and other aluminum alloys. Despite excellent performance, these aluminum alloys have seen limited use outside of the aerospace industry due in part to high cost. If high-performance aluminum extrusions could be made more cost effectively by eliminating energy intensive process steps typical of conventional extrusion, then numerous opportunities exist for more widespread adoption. A key reason for the high cost of 7075 and 2024 extrusions (25-75% higher than 6061) is their slow extrusion speed. 7075 and 2024 are limited to 2 m/min and 3.5 m/min respectively, in contrast to 6061 which can be extruded at 20–80 m/min. In addition to slow speed, aluminum alloys require numerous thermal treatments throughout the extrusion process including homogenization and pre-heating prior to extrusion, and solution heat treating and artificial aging after extrusion. Each of these steps contribute to the total energy consumed during manufacturing of extruded components. This project investigates the use of ShAPE to improve extrusion speed and reduce, or even eliminate, the typical thermal treatments for high strength aluminum alloys, all while improving material performance. The overarching goal of this project was to demonstrate that Shear Assisted Processing and Extrusion (ShAPE) can manufacture high-performance aluminum alloy tubing with lower manufacturing energy and improved mechanical properties compared to conventional extrusion. Unlike conventional extrusion where the billet is rammed against a stationary die using a strictly linear motion, the ShAPE process superimposes a rotational shear force by spinning the die while the billet is plunged. Compared to conventional linear extrusion, the ShAPE process imparts significantly more strain into the feedstock material, which enables the formation of novel microstructures. These microstructures manifest an array of property and process improvements for extrusion of high-performance aluminum alloys. The following accomplishments were achieved for this project: Extrusion of 7075 at 12.2 meters/min compared to 2 meters/min for conventional extrusion; Elimination of 7075 billet homogenization (430 °C for 20 hours) which is required prior to conventional extrusion; Elimination of 7075 billet pre-heating (400 °C for 1 hour) in a separate furnace which is required prior to conventional extrusion; Achieved 7075-T6with yield strength = 595 MPa, ultimate tensile strength = 531MPa, and elongation = 17.4% for extrusions made from unhomogenized billets. Exceeds the ASTM and ASM standard, and typical industry values; Achieved 7075-T5 (i.e., no solution heat treatment) with yield strength = 588 MPa, ultimate tensile strength = 535 MPa, and elongation = 14.8% for extrusions made from homogenized billets; Extrusion of 2024 at 7.4 meters/min compared to 3.5 meters/min for conventional extrusion; Achieved 2024-T8510 yield strength = 522 MPa, ultimate strength = 510MPa, and elongation = 7.1% for extrusions made from wrought billets. Exceeds the ASTM and ASM standard, and typical industry values; Extrusion of Al-12.4TM high-performance aluminum powder directly into tubing, in a single step, which eliminates process steps typical of powder metallurgy extrusion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

HI-STORM Overpack and MPC-32 Thermal-Hydraulic Model with MOOSE Framework

Nuclear power is a significant source of electricity in the United States, but the average age of nuclear power plants is around 40 years old. The safe management of the spent nuclear fuel (SNF) is a key aspect of the back-end of the nuclear fuel cycle. Spent fuel dry storage systems are becoming a popular and effective solution in this area, given the absence of a final disposal system. The spent fuel cask system (dry cask method) provides a feasible solution to maintain spent fuel for 60 years before final disposal. Dry cask storage has many characteristics that make it attractive. It fulfills the safety requirements of the Nuclear Regulatory Commission (NRC) while providing modularity and flexibility to contractors. The HI-STORM overpack and MPC-32 canister are the main parts of the HI-STORM 100 dry cask storage system. These components remove heat from the system using natural circulation, requiring no human intervention. This is the characteristic that provides passive heat removal and low maintenance features in dry cask storage systems. To develop a thermal model for a dry cask storage system, the physics behind the system should be defined clearly. There are two natural circulation loops in the system; circulation of helium cools down the nuclear assemblies in the MPC, while circulation of air cools down the walls of the MPC. This work aims to develop a thermal model of the MPC-32 canister and HI-STORM overpack using the Multiphysics Object-Oriented Simulation Environment (MOOSE). MOOSE is an open-source framework developed by Idaho National Laboratory (INL) for multiscale, multiphysics simulations. In this study, we will investigate and demonstrate the thermal-hydraulics modeling capabilities of the MOOSE framework, including natural circulation, heat transfer, and porous flow.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Photovoltaic Module Imaging for Hail Damage Assessment with Multi-Year Follow Up

Outdoor-aged photovoltaic modules that have experienced golf-ball sized hail are characterized by flash testing and photoluminescence, electroluminescence, thermal, and ultraviolet fluorescence imaging. These measurements were performed immediately after the hailstorm and then again after another two years and four years in the field. The modules originally experienced different ranges of hail damage with some having cracks on approximately half of the cells and some having few to no cracked cells. Flash testing shows that the hail-damaged modules with the most cracked cells have 3 to 4% less power than those with the least damage. After four more years in the outdoor climate of Golden, Colorado since the hailstorm, all of the modules still exhibit similar relative power and amounts of cell cracking, suggesting that the hail damage has only initially reduced power but has not yet increased the degradation rate.

electroluminescence↗
DOE OSTI2024

Formation of the {gamma}ʹʹʹ-Ni2(Cr, Mo, W) phase during a two-step aging heat treatment in HAYNES® 244® Alloy

Precipitation hardening is the dominant method of achieving high strength in most Ni-based superalloys. The formation of nanoscale precipitates during thermal exposure is often studied to determine the optimal methods of attaining high strength. The commercial Ni-based superalloy, HAYNES® 244® alloy, is strengthened through a novel -Ni2(Cr, Mo, W) intermetallic phase that forms during a two-step aging cycle. The precipitation kinetics of this intermetallic phase are sluggish for single-step aging in comparison to the γʹ phase in precipitation-strengthened Ni-based alloys, but a two-step aging treatment has shown to reliably harden the alloy and improve high-temperature properties compared to a single-step aging heat treatment. To investigate the formation and coarsening of this phase, heat-treated samples of the 244 alloy were analyzed with high-energy in situ and ex situ X-ray techniques such as small angle X-ray scattering and wide angle X-ray scattering as well as Vickers micro-hardness, electron microscopy, and atom probe tomography. The relationship between hardness, aging parameters, and microstructure evolution is discussed. The enthalpy of formation and precipitate solvus temperature were determined with high-temperature differential scanning calorimetry and dilatometry analysis.

Ni-based Superalloys↗