SEARCH · Search NASA
Results for “thermoelectric materials”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal
Abstract Thermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2–2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m –1 K –1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.
High Thermoelectric Performance through Crystal Symmetry Enhancement in Triply Doped Diamondoid Compound Cu 2 SnSe 3
The presence of high crystallographic symmetry and nanoscale defects are favorable for thermoelectrics. With proper electronic structures, a highly symmetric crystal tends to possess multiple carrier channels and promote electrical conductivity without sacrificing Seebeck coefficient. In addition, nanoscale defects can effectively scatter acoustic phonons to suppress thermal conductivity. Here, we report that the triple doping of Cu 2 SnSe 3 leads to a high ZT value of 1.6 at 823 K for Cu 1.85 Ag 0.15 (Sn 0.88 Ga 0.1 Na 0.02 )Se 3 , and a decent average ZT (ZT ave ) value of 0.7 is also achieved for Cu 1.85 Ag 0.15 (Sn 0.93 Mg 0.06 Na 0.01 )Se 3 from 475 to 823 K. Our study reveals: (1) Ag doping on Cu sites generates numerous point defects and greatly decreases lattice thermal conductivity. (2) Doping Mg or Ga converts the monoclinic Cu 2 SnSe 3 into a cubic structure. This symmetry enhancing leads to increase in the effective mass from 0.8 m e to 2.6 m e (m e , free electron mass) and the power factor from 4.3 μW/cm –1 K –2 for Cu 2 SnSe 3 to 11.6 μW/cm –1 K –2 . (3) Na doping creates dense dislocation arrays and nanoprecipitates, which strengthens the phonon scattering. (4) Pair distribution function analysis shows localized symmetry breakdwon in the cubic Cu 1.85 Ag 0.15 (Sn 0.88 Ga 0.1 Na 0.02 )Se 3 . Furthermore, the present work provides a standpoint to design promising thermoelectric materials by synergistically manipulating crystal symmetry and nanoscale defects.
Two-watt radioisotope power generators for underwater applications
Materials and design considerations are discussed for a low-cost, reliable radio-isotope-fueled thermoelectric generator for use in an undersea application. Plutonium has been selected as fuel, and the generator has to meet design goals of 2 watts after 20 years with a direct output voltage of 6-8 volts. The pressed and sintered form of Bi2Te3 appears to be the most appropriate thermoelectric material. Both fibrous and multilayer foil insulation could be used with proper processing and quality control, but there is less risk with fibrous type insulation. Min-K 1400 is recommended with a nitrogen cover gas. The heat source recommended is a three-layer capsule using T-111 for both the liner and strength member with an outer liner of Hastelloy-C.
A Case Study of Multimodal, Multi-institutional Data Management for the Combinatorial Materials Science Community
Although the convergence of high-performance computing, automation, and machine learning has significantly altered the materials design timeline, transformative advances in functional materials and acceleration of their design will require addressing the deficiencies that currently exist in materials informatics, particularly a lack of standardized experimental data management. The challenges associated with experimental data management are especially true for combinatorial materials science, where advancements in automation of experimental workflows have produced datasets that are often too large and too complex for human reasoning. The data management challenge is further compounded by the multimodal and multi-institutional nature of these datasets, as they tend to be distributed across multiple institutions and can vary substantially in format, size, and content. Furthermore, modern materials engineering requires the tuning of not only composition but also of phase and microstructure to elucidate processing–structure–property–performance relationships. To adequately map a materials design space from such datasets, an ideal materials data infrastructure would contain data and metadata describing (i) synthesis and processing conditions, (ii) characterization results, and (iii) property and performance measurements. In this work, we present a case study for the low-barrier development of such a dashboard that enables standardized organization, analysis, and visualization of a large data lake consisting of combinatorial datasets of synthesis and processing conditions, X-ray diffraction patterns, and materials property measurements generated at several different institutions. While this dashboard was developed specifically for data-driven thermoelectric materials discovery, we envision the adaptation of this prototype to other materials applications, and, more ambitiously, future integration into an all-encompassing materials data management infrastructure.
Opening the Bandgap of Metallic Half-Heuslers via the Introduction of d–d Orbital Interactions
Half-Heusler compounds with semiconducting behavior have been developed as high-performance thermoelectric materials for power generation. Many half-Heusler compounds also exhibit metallic behavior without a bandgap and thus inferior thermoelectric performance. Here, taking metallic half-Heusler MgNiSb as an example, a bandgap opening strategy is proposed by introducing the d–d orbital interactions, which enables the opening of the bandgap and the improvement of the thermoelectric performance. The width of the bandgap can be engineered by tuning the strength of the d–d orbital interactions. The conduction type and the carrier density can also be modulated in the Mg 1- x Ti x NiSb system. Both improved n-type and p-type thermoelectric properties are realized, which are much higher than that of the metallic MgNiSb. The proposed bandgap opening strategy can be employed to design and develop new half-Heusler semiconductors for functional and energy applications.
Research in the conversion of various forms of energy by unconventional techniques Status report
Thermoelectric materials engineering, plasma physics, and electrochemistry for direct energy conversion systems
Effect of Sn oxides on the thermal conductivity of polycrystalline SnSe
SnSe is a promising thermoelectric material, with intrinsically low lattice thermal conductivity, κL. Surprisingly, in several reports, polycrystalline samples are found to have a higher thermal conductivity than single crystals. This disparity has been attributed to trace amounts of thermally conductive Sn oxides at the grain boundaries of polycrystalline samples. The same culprit was recently proposed to explain the reduction of κL in purified, oxide-free, SnSe polycrystals. Here, we test this hypothesis by: (i) tuning the type of oxide in SnSe by exploiting thermodynamic stability regions, since Sn-rich or Sn-poor compositions favour the formation of SnO or SnO 2 , respectively; and (ii) varying the quantity of SnO 2 by intentionally oxidizing SnSe powder before consolidation, to obtain samples with quantifiable amounts - up to 15% - of SnO 2 . We find that the κL of SnSe is impervious to changes in the type or the amount of Sn oxide present in the samples. Our results show that a simple “rule of mixtures” cannot be used to estimate the effect of grain boundary oxides on the thermal conductivity of SnSe. These results call for an improved understanding of the intriguing thermal transport mechanisms in SnSe and numerous other systems where a two-phase transport is presumed.
GaSb doping facilitates conduction band convergence and improves thermoelectric performance in n-type PbS
P-type lead chalcogenides have superior thermoelectric performance because they exhibit the energy convergence of several valence bands. However, despite the existence of two conduction bands, there has been no report about conduction band (CB) convergence for n-type counterparts because of the large energy difference between them. Therefore, new strategies are required to manipulate the CBs if enhancing the electrical transport performance of n-type lead chalcogenides is to be achieved. PbS is a highly attractive member of the lead chalcogenides because of its high earth-abundance and low cost. Here, we report that the introduction of GaSb can successfully dope the PbS matrix with Ga and Sb atoms occupying the Pb site in its rock salt structure. GaSb doping leads to conduction band convergence and enlarged effective density of state mass for n-type PbS. This effect results in superior power factor and decreased lattice thermal conductivity caused by the soft phonon modes and point defect scattering of phonons. Consequently, a record-high average power factor PF avg of ~20.4 μW cm –1 K –2 and figure of merit ZT avg of ~0.84 in the temperature range of 400 K to 923 K were obtained, higher than any n- and p-type PbS-based thermoelectric materials.
Thermoelectric Energy Conversion: Future Directions and Technology Development Needs
This viewgraph presentation reviews the process of thermoelectric energy conversion along with key technology needs and challenges. The topics include: 1) The Case for Thermoelectrics; 2) Advances in Thermoelectrics: Investment Needed; 3) Current U.S. Investment (FY07); 4) Increasing Thermoelectric Materials Conversion Efficiency Key Science Needs and Challenges; 5) Developing Advanced TE Components & Systems Key Technology Needs and Challenges; 6) Thermoelectrics; 7) 200W Class Lightweight Portable Thermoelectric Generator; 8) Hybrid Absorption Cooling/TE Power Cogeneration System; 9) Major Opportunities in Energy Industry; 10) Automobile Waste Heat Recovery; 11) Thermoelectrics at JPL; 12) Recent Advances at JPL in Thermoelectric Converter Component Technologies; 13) Thermoelectrics Background on Power Generation and Cooling Operational Modes; 14) Thermoelectric Power Generation; and 15) Thermoelectric Cooling.
Hierarchical microstructure of Yb-filled skutterudites through ultrasonically atomized spherical powders for enhanced thermoelectric performance
Hierarchical microstructures are widely explored as a strategy to reduce lattice thermal conductivity in thermoelectric materials while preserving favorable electronic transport. Here we demonstrate that ultrasonic atomization of precursor powders provides an intrinsic pathway to generate such architectures in n-type Yb0.3Co4Sb12 skutterudites. Materials were synthesized by both conventional sealed-ampoule and ultrasonic atomization routes, each yielding essentially single-phase skutterudite after densification. However, the atomized spherical powders undergo a distinct reaction-driven microstructural evolution during thermal treatment prior to densification. Electron microscopy reveals that the skutterudite phase within the particles induces swelling, cracking, and fragmentation of the droplets before consolidation. Multimodal structural and microstructural characterizations show that densification of these fragmented powders produces a hierarchical microstructure consisting of submicron grains, micrometer-scale faceted crystallites, and powder-derived domains separated by oxide-decorated boundaries. Comprehensive thermoelectric transport measurements evidence that this multiscale architecture lowers the lattice thermal conductivity while maintaining favorable electronic transport, leading to an average ~10% enhancement in the thermoelectric figure of merit. Complementary 121Sb Mössbauer spectroscopy further indicates lattice softening in the atomized material. These results demonstrate that ultrasonic atomization provides an effective route to engineer hierarchical microstructures in skutterudite thermoelectrics and offers a promising strategy for tailoring thermal transport in energy-conversion materials.
Conduction band convergence and local structure distortion for superior thermoelectric performance of GaSb-doped n-type PbSe thermoelectrics
Achieving high-stability thermoelectric materials with excellent average power factor and figure of merit is crucial for maximizing the output power density and conversion efficiency of thermoelectric devices. In this study, GaSb is added to PbSe as an n-type dopant to form stable solid solutions. Doping with GaSb flattens the conduction band and reduces the energy difference between the Σ and L conduction bands, thereby significantly improving the Seebeck coefficient. Herein, the Ga and Sb atoms co-occupy the vacant Pb sites, unlike in the case of traditional single-element doping, as is verified by density functional theory calculations. The resultant structural distortion is confirmed via transmission electron microscopy. This local structure distortion caused by GaSb doping reduces the lattice thermal conductivity. Consequently, the Pb 0.99875 (GaSb) 0.00125 Se sample exhibits a record-high average power factor of ~22.37 μW cm −1 K −2 and a high average figure of merit of ~0.94 in the temperature range of 300‒873 K. Furthermore, the introduction of interstitial Cu and discordant Zn atoms further reduces the lattice thermal conductivity. The Pb 0.99875 (GaSb) 0.00125 Zn 0.01 Se 1.01 -0.3%Cu sample exhibits a low lattice thermal conductivity of ~0.4 W m −1 K −1 at 873 K and a record-high average figure of merit of ~1.01 in the temperature range of 300‒873 K.
Contrasting SnTe–NaSbTe 2 and SnTe–NaBiTe 2 Thermoelectric Alloys: High Performance Facilitated by Increased Cation Vacancies and Lattice Softening
Defect chemistry is critical to designing high performance thermoelectric materials. In SnTe, the naturally large density of cation vacancies results in excessive hole doping and frustrates the ability to control the thermoelectric properties. Yet, recent work also associates the vacancies with suppressed sound velocities and low lattice thermal conductivity, underscoring the need to understand the interplay between alloying, vacancies, and the transport properties of SnTe. Here, we report solid solutions of SnTe with NaSbTe 2 and NaBiTe 2 (NaSn m SbTe m +2 and NaSn m BiTe m +2 , respectively) and focus on the impact of the ternary alloys on the cation vacancies and thermoelectric properties. We find introduction of NaSbTe 2 , but not NaBiTe 2 , into SnTe nearly doubles the natural concentration of Sn vacancies. Furthermore, DFT calculations suggest that both NaSbTe 2 and NaBiTe 2 facilitate valence band convergence and simultaneously narrow the band gap. These effects improve the power factors but also make the alloys more prone to detrimental bipolar diffusion. Indeed, the performance of NaSn m BiTe m +2 is limited by strong bipolar transport and only exhibits modest maximum ZTs ≈ 0.85 at 900 K. In NaSn m SbTe m +2 however, the doubled vacancy concentration raises the charge carrier density and suppresses bipolar diffusion, resulting in superior power factors than those of the Bi-containing analogues. Lastly, NaSbTe 2 incorporation lowers the sound velocity of SnTe to give glasslike lattice thermal conductivities. Facilitated by the favorable impacts of band convergence, vacancy-augmented hole concentration, and lattice softening, NaSn m SbTe m +2 reaches high ZT ≈ 1.2 at 800–900 K and a competitive average ZT avg of 0.7 over 300–873 K. The difference in ZT between two chemically similar compounds underscores the importance of intrinsic defects in engineering high-performance thermoelectrics.
System to Measure Thermal Conductivity and Seebeck Coefficient for Thermoelectrics
The Seebeck coefficient, when combined with thermal and electrical conductivity, is an essential property measurement for evaluating the potential performance of novel thermoelectric materials. However, there is some question as to which measurement technique(s) provides the most accurate determination of the Seebeck coefficient at elevated temperatures. This has led to the implementation of nonstandardized practices that have further complicated the confirmation of reported high ZT materials. The major objective of the procedure described is for the simultaneous measurement of the Seebeck coefficient and thermal diffusivity within a given temperature range. These thermoelectric measurements must be precise, accurate, and reproducible to ensure meaningful interlaboratory comparison of data. The custom-built thermal characterization system described in this NASA-TM is specifically designed to measure the inplane thermal diffusivity, and the Seebeck coefficient for materials in the ranging from 73 K through 373 K.
Plasma-jet printing of colloidal thermoelectric Bi 2 Te 3 nanoflakes for flexible energy harvesting
Thermoelectric generators (TEGs) convert temperature differences into electrical power and are attractive among energy harvesting devices due to their autonomous and silent operation. While thermoelectric materials have undergone substantial improvements in material properties, a reliable and cost-effective fabrication method suitable for microgravity and space applications remains a challenge, particularly as commercial space flight and extended crewed space missions increase in frequency. This paper demonstrates the use of plasma-jet printing (PJP), a gravity-independent, electromagnetic field-assisted printing technology, to deposit colloidal thermoelectric nanoflakes with engineered nanopores onto flexible substrates at room temperature. We observe substantial improvements in material adhesion and flexibility with less than 2% and 11% variation in performance after 10 000 bending cycles over 25 mm and 8 mm radii of curvature, respectively, as compared to previously reported TE films. Our printed films demonstrate electrical conductivity of 2.5 × 10 3 S m -1 and a power factor of 70 μW m -1 K -2 at room temperature. To our knowledge, these are the first reported values of plasma-jet printed thermoelectric nanomaterial films. This advancement in plasma jet printing significantly promotes the development of nanoengineered 2D and layered materials not only for energy harvesting but also for the development of large-scale flexible electronics and sensors for both space and commercial applications.
Modified silicon-germanium alloys with improved performance
This paper discusses the results of a program on the modification of silicon-germanium alloys by means of small extraneous material additions in order to improve their figures-of-merit. A review of the properties that constitute the figure-of-merit indicates that it is the relatively high thermal conductivity of silicon-germanium alloys that is responsible for their low values of figure-of-merit. The intent of the effort discussed in this paper is therefore the reduction of the thermal conductivity of silicon-germanium alloys by minor alloy additions and/or changes in the basic structure of the material. Because Group III and V elements are compatible with silicon and germanium, the present effort in modifying silicon-germanium alloys has concentrated on additions of gallium phosphide. A significant reduction in thermal conductivity, approximately 40 to 50 percent, has been demonstrated while the electrical properties are only slightly affected as a result. The figure-of-merit of the resultant material is enhanced over that of silicon-germanium alloys and when fully optimized is potentially better than that of any other presently available thermoelectric material.
Space nuclear power systems; Proceedings of the 8th Symposium, Albuquerque, NM, Jan. 6-10, 1991. Pts. 1-3
The present conference discusses NASA mission planning for space nuclear power, lunar mission design based on nuclear thermal rockets, inertial-electrostatic confinement fusion for space power, nuclear risk analysis of the Ulysses mission, the role of the interface in refractory metal alloy composites, an advanced thermionic reactor systems design code, and space high power nuclear-pumped lasers. Also discussed are exploration mission enhancements with power-beaming, power requirement estimates for a nuclear-powered manned Mars rover, SP-100 reactor design, safety, and testing, materials compatibility issues for fabric composite radiators, application of the enabler to nuclear electric propulsion, orbit-transfer with TOPAZ-type power sources, the thermoelectric properties of alloys, ruthenium silicide as a promising thermoelectric material, and innovative space-saving device for high-temperature piping systems. The second volume of this conference discusses engine concepts for nuclear electric propulsion, nuclear technologies for human exploration of the solar system, dynamic energy conversion, direct nuclear propulsion, thermionic conversion technology, reactor and power system control, thermal management, thermionic research, effects of radiation on electronics, heat-pipe technology, radioisotope power systems, and nuclear fuels for power reactors. The third volume discusses space power electronics, space nuclear fuels for propulsion reactors, power systems concepts, space power electronics systems, the use of artificial intelligence in space, flight qualifications and testing, microgravity two-phase flow, reactor manufacturing and processing, and space and environmental effects.
Weak Electron–Phonon Coupling and Enhanced Thermoelectric Performance in n-type PbTe–Cu 2 Se via Dynamic Phase Conversion
This study investigates Ga-doped n-type PbTe thermoelectric materials and the dynamic phase conversion process of the second phases via Cu 2 Se alloying. Introducing Cu 2 Se enhances its electrical transport properties while reducing its lattice thermal conductivity (κlat) via weak electron–phonon coupling. Additionally, Cu 2 Te and CuGa(Te/Se) 2 (tetragonal phase) nanocrystals precipitate during the alloying process, resulting in Te vacancies and interstitial Cu in the PbTe matrix. At room temperature, Te vacancies and interstitial Cu atoms serve as n-type dopants, increasing the carrier concentration and electrical conductivity from ≈1.18 × 10 19 cm –3 and ≈1870 S cm –1 to ≈2.26 × 10 19 cm –3 and ≈3029 S cm –1 , respectively. With increasing temperature, the sample exhibits a dynamic change in Cu 2 Te content and the generation of a new phase of CuGa(Te/Se) 2 (cubic phase), strengthening the phonon scattering and obtaining an ultralow k lat . Pb 0.975 Ga 0.025 Te-3%CuSe exhibits a maximum figure of merit of ≈1.63 at 823 K, making it promising for intermediate-temperature device applications.