Search NASA⌕ Search

SEARCH · Search NASA

Results for “60”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

4.6 V Moisture‐Tolerant Electrolytes for Lithium‐Ion Batteries

Abstract Commercial LiPF 6 ‐based electrolytes face limitations in oxidation stability (4.2 V) and water tolerance (10 ppm). While replacing LiPF 6 with lithium bis(trifluoromethane)sulfonimide (LiTFSI) improves water tolerance, it induces Al current collector corrosion above 3.7 V vs. Li/Li + . To address this, lithium cyano(trifluoromethanesulfonyl)imide (LiCTFSI) is proposed here as a non‐corrosive, moisture‐tolerant alternative. The 2.0 M LiCTFSI/propylene carbonate (PC)‐fluoroethylene carbonate (FEC) (7:3 by volume) electrolyte enables LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathodes to reach 210 mAh g −1 (2.8‐4.6 V) with a cycle life of 500. Full cells with NCM811||graphite (2.0 mAh cm −2 ) show 77.8% capacity retention after 500 cycles. Even with 2000 ppm moisture in the electrolyte, full cells maintain high cycling stability, reducing the need for costly dry rooms. The electrolyte’s low freezing point and high thermal stability enable the operation from ‐20 °C to 60 °C, delivering 168 mAh g −1 at ‐20 °C and retaining 94% capacity after 100 cycles at 60 °C. In contrast, cells with commercial LiPF 6 electrolyte deliver 71 mAh g −1 at ‐20°C and retain 52.7% after 100 cycles at 60 °C. This novel salt offers a cost‐effective solution for developing robust, high‐performance batteries suitable for extreme conditions.

Zhang, Nan↗
DOE OSTI2024

Field‐representative evaluation of PID‐polarization in TOPCon PV modules by accelerated stress testing

Abstract Potential‐induced degradation‐polarization (PID‐p) can reduce module power, but how to project the extent to which PID‐p may occur in field conditions considering the factors of system voltage, condensed moisture, temperature, and illumination has not been clarified. Using tunnel oxide passivated contact (TOPCon) modules, this work demonstrates a method to test full‐size crystalline silicon PV modules for PID‐p to provide field‐representative results. In initial screening tests with positive or negative 1000 V electrical bias applied at 60°C for 96 h using Al foil electrodes on the glass surfaces, the module type exhibited reversible PID‐p only on the front face when the cell circuit was in negative voltage potential. No PID was detected on the rear after testing in either polarity. We then evaluated the PID‐p sensitivity on the front side under different UV irradiances while maintaining the glass surface wet to estimate real‐world susceptibility to PID‐p. The magnitude of the observed behavior was fit using a previously developed charge transfer and depletion by light model. Whereas power loss with −1000 V applied to the cell circuit at 60°C for 96 h in the dark was about 30%, testing the module front under 0.051 W·m −2 nm −1 at 340 nm UVA irradiation using fluorescent tubes, the mean degradation was only 3%. When the modules were tested in the dark for PID‐p with in situ dark current–voltage (I‐V) characterization, the thermal activation energy for degradation was 0.71 eV; for recovery in the dark, it was 0.58 eV. Whereas recovery from the degraded state at 60°C in the dark without voltage bias was 5% absolute in 38 h, rapid recovery of about 5% absolute was observed with 1000 W·s/m 2 exposure at 25°C using a flash tester.

14 SOLAR ENERGY↗
DOE OSTI2021

Prehydration of calcium sulfoaluminate (CSA) clinker at different relative humidities

The use of CSA cement in practice has been hindered by its unstable performance and short shelf-life caused by the prehydration of CSA clinker. In this study, the effect of ambient humidity on the prehydration rate and process of CSA clinker was investigated. The prehydration degree, ageing progress, and the dynamic change of mineral composition of CSA clinker exposed to five different relative humidities (ranging from 23% to 98%) for up to 180 days were studied. Experiments revealed that the ambient humidity of 60% RH can be considered a threshold value for storage of CSA clinker. Exposure of CSA clinker to RH higher than 60% will not only result in a significant decrease of hydraulic reactivity, but also in agglomeration of the clinker. Although the exposure of CSA clinker to RH lower than 60% has little effect on the hydraulic reactivity, the main hydration peak was found to be slightly delayed with the increase of RH.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Superconducting properties of commercially available solders for low-field applications

Solders with superconducting transitions around 4K are useful in low magnetic field environments for AC current leads or in electrical and mechanical bonds. Accurate knowledge of these solders’ superconducting properties is essential for improving high precision experiments. We have measured the electrical resistance of five commercially-available eutectic or near-eutectic solders: 50%Sn-50%Pb, 60%Sn-40%Pb, 60%Sn-40%Pb-0.3%Sb, 52%In-48%Sn, and 96.5%Sn-3.5%Ag, down to 2.3K and in applied magnetic fields from 0 to 0.1 T . We report critical temperatures T c (B), 90%–10% transition widths ΔT c , and zero-temperature critical fields B c,0 . Our best candidate for low-loss AC current wiring in low fields is 50%Sn-50%Pb, which has a zero-field T c,0 = 7.1K (with ΔT c = 0.6 K), and remained high at T c (0.1 T) = 6.9K (ΔT c = 0.6K ). We also report, for the first time, T c and B c of 60%Sn-40%Pb-0.3%Sb and B c,0 of 96.5%Sn-3.5%Ag. Our T c,0 - 3.31K (ΔT c = 0.08K) for 96.5%Sn-3.5%Ag disagrees with a widely adopted value.

Hickman, C. [North Carolina State University, Rale↗
DOE OSTI2023

Highly swollen ROMP-based gels

In this study, the leakage of organic solvent during the transportation and storage is one of the major threats to the environment. Networks/gels acting as the absorbing materials for organic solvents are the most promising solution for the organic solvent pollution. Here, we report the synthesis of highly swollen networks/gels in high yield (≥95%) via ring opening metathesis polymerization (ROMP) using Grubbs’ first generation catalyst/initiator (G1), a crosslinker (1,1'-(methylenedi-4,1-phenylene)bis-exo-7-oxanorbornenecarboximide) and monofunctional monomer/diluent (exo-N-phenyl-7-oxanorbornenecarboximide). The mesh size of the network was varied by keeping the concentration of monomer constant while changing the concentrations of crosslinker and G1 (initiator). The swelling capacity of the network in N,N-dimethylformamide (DMF) solvent increased from 41 to 53 and to 61 with the increase of theoretical mesh size (molar ratio of monomer to crosslinker) from 20 to 40 and to 60, respectively. By further increasing the mesh size from 60 to 80 there was no significant change in swelling capacities (63). Thus, the gel with the mesh size of 60 was selected for swelling capacity analysis in other polar organic solvents such as dimethyl sulfoxide (DMSO), dichloromethane (DCM), chloroform and lithium-ion battery electrolyte solution (1.0 M LiPF 6 in ethylene carbonate (EC)/diethyl carbonate (DEC) = 50/50 (v/v)). They showed the decreased swelling capacity value from 61 to 57, 40, 31 and 5, respectively. For a controlled mesh size ROMP-based gel, we observed the highest swelling capacity values to date.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving the barrier properties of tin oxide in metal halide perovskite solar cells using ozone to enhance nucleation

Here we investigate tin oxide growth on fullerene (C 60 ) by atomic layer deposition (ALD) for C 60 /oxide bilayer electron selective contacts in P-I-N metal halide perovskite (MHP) solar cells. An in situ ozone functionalization step is incorporated in an ALD SnO x process to suppress sub-surface growth, leading to improved internal barrier performance of ALD SnO x thin films grown on fullerene surfaces. We show that this approach decreases the water-vapor transmission rate of C 60 /ALD SnO x barriers by an order of magnitude and improves the barrier properties against gas, solvent, and halide migration. Furthermore, ozone-treated SnO x barriers can narrow photovoltaic performance distribution without compromising efficiency. We demonstrate the universality of this approach in wide-, intermediate-, and low-gap perovskite systems and further show that enhancement of the ALD barrier layer is critical toward improving the yield of all-perovskite tandem solar cells. Two-terminal all-perovskite tandem solar cells incorporating ozone nucleation are reported at over 24% photovoltaic conversion efficiency.

14 SOLAR ENERGY↗
DOE OSTI2026

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗
DOE OSTI2020

Genetic algorithm optimization of tin–copper graded shielding for improved plutonium safeguards measurements

Plutonium nuclear material safeguards is essential to ensure that states do not divert plutonium to clandestine nuclear weapons programs. Traditional safeguards methods rely on correlated neutron measurements. Detection systems based on organic scintillators, which are sensitive to fast neutrons and photons, are gaining support for use in safeguards applications due to increased capabilities and shorter measurement times compared to the current state-of-the-art. A drawback of organic scintillators in plutonium measurements is data throughput limitations; 241 Am builds up in plutonium samples and emits 60-keV gamma rays with a high specific activity. In this work, a genetic algorithm is used to design graded shielding made of tin and copper to attenuate the 60-keV gamma rays. The shield is designed to limit the attenuation of the higher-energy, fission photons, because fission photons can be used as a signature. The genetic algorithm optimization takes days to run, while a complete search space exploration would take years. The genetic algorithm was run for different levels of 60-keV gamma-ray attenuation, and the thickness of the required shielding layers was determined at each level. Tin–copper shielding was placed in front of an array of organic scintillation detectors for a measurement of approximately 4.5 kg of alpha-phase, weapons-grade plutonium, an AmLi source, and a 252 Cf source. We show that the shield successfully attenuated low-energy, non-fission gamma rays, which significantly improved the organic scintillator performance.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Fullerene Promotes CO 2 Reduction to Methanol by a Cobalt(II) Phthalocyanine Electrocatalyst

Heterogenization of molecular electrocatalysts offers an attractive way to improve the catalytic selectivity and efficiency of CO 2 conversion to liquid fuels. Herein, we employ density functional theory to compare the mechanism of CO 2 RR by a cobalt(II) tetra(amino)phthalocyanine (Co(II)Pc(NH 2 ) 4 ) electrocatalyst with and without the presence of fullerene support. Our DFT calculations suggest that the CO 2 reduction mechanism is initiated by a metal-based electron reduction followed by subsequent CO 2 nucleophilic addition, electron transfer, proton transfer, water dissociation, and proton-coupled electron transfer steps that lead to CO and methanol formation. We show that graphitic interactions between the Co(II)Pc(NH 2 ) 4 electrocatalyst and C 60 support selectively improve the CO 2 RR to methanol at mild potentials. The undesirable hydrogen evolution reaction (HER) was also investigated for both electrocatalysts and proceeds via the protonation of the cobalt metal center over the nitrogen atom in the inner ring. The competition between the HER and the CO 2 RR was improved in favor of CO and methanol formation using the Co(II)Pc(NH 2 ) 4 @C 60 electrocatalyst. Overall, our results suggest C 60 as a promising graphitic support for molecular electrocatalysts integration for CO 2 catalysis.

Alcohols↗
DOE OSTI2024

AC Magnetometry Using Nano-ferrofluid Cladded Multimode Interferometric Fiber Optic Sensors for Power Grid Monitoring Applications

The AC magnetic field response of the superparamagnetic nano-ferrofluid is an interplay between the Neel and Brownian relaxation processes and is generally quantified via the susceptibility measurements at high frequencies. The high frequency limit is dictated by these relaxation times which need to be shorter than the time scale of the time varying magnetic field for the nano-ferrofluid to be considered in an equilibrium state at each time instant. Even though the high frequency response of ferrofluid has been extensively investigated for frequencies up to GHz range by non-optical methods, harnessing dynamic response by optical means for AC magnetic field sensing in fiber-optic-based sensors-field remains unexplored. Instead, the incorporation of nano-ferrofluid as sensing materials has been only limited to DC magnetic field sensing, often citing their long response time as a limiting factor to AC field sensing. This work reports the finding of high frequency (up to 15 kHz) AC magnetic field sensing capability of nanomagnetic fluid as the cladding material of a fiber-optic multimode interferometry (MMI) structure optimized for the fourth self-imaging spectral response. The key parameter enabling high frequency response is the short response time (<1 ms) achieved by optimizing both the sensing structure and nano-ferrofluid solution. Focus has been imparted on 60 Hz line-frequency profiles of various current/magnetic fields to test the efficacy of these sensors in metering and monitoring current and current-induced magnetic fields in the electrical power grid systems. The magnetic field sensitivity of 240 mV/Gauss per dBm of transmitted power was achieved for 60 Hz field applied via Helmholtz coil, whereas the 60 Hz AC current sensitivity of 2.83 mV/A was measured due to magnetic field induced by current in a straight conducting wire.

42 ENGINEERING↗
DOE OSTI2026

On-Chip Tuning of Superconductivity in Fullerides via Current-Driven Rb + Intercalation

An in-operando electro-intercalation method for the on-chip synthesis of alkali-metal-intercalated materials and their Raman spectroscopic and transport characterization in ultrahigh vacuum (UHV) is developed. We apply this method to synthesize fulleride superconductors via Rb + intercalation into a C 60 film. During the intercalation, we monitor the stoichiometry via UHV-Raman spectroscopy and probe superconductivity via transport measurements. An increase of the superconducting transition temperature from 7.0 K to 14.5 K is observed when the stoichiometry is tuned from Rb 2.7 C 60 to Rb 3 C 60 . In our experiment, an ionic Rb+ flux into the host material is induced by an applied electronic current via a Butler–Volmer-type mechanism. Electro-intercalation captivates through improved stoichiometric precision, the ability to smoothly vary stoichiometry via duration of current application, and the absence of a lower limit of the volume of the host material. It represents a powerful concept for the on-chip synthesis of intercalated materials, battery research, and beyond.

Raman↗
DOE OSTI2025

Opportunistic Short‐Term Water Uptake Dynamics by Subalpine Trees Observed via In Situ Water Isotope Measurements

Abstract Variations in tree water sources are important to understand in semi‐arid ecosystems because climatic shifts towards lower snowpack and increased drought affect water availability in subalpine forests of the western US. Here, we use daily in situ measurements of stable isotopes ( 2 H & 18 O) in soil and tree stem water, soil matric potential and sap flow to study tree water uptake dynamics. We instrumented three soil profiles down to 90 cm, as well as three aspen and engelmann spruce trees near Gothic, Colorado, in the East River watershed. We observed the fate of natural isotopic variations in rainfall, soil, and plants from June to October 2022, and in August 2023 we conducted a 2 H labeled irrigation experiment. Our observations showed that all studied aspen trees compensated for water scarcity in the shallow soil by shifting the dominant water source at 60(±20) cm to ⅔ of uptake from 90 cm within a few days of a dry period. Both species relied on snowmelt stored in the subsoil to sustain transpiration. Intense rainfall caused the plant water uptake to shift partially to top soil layers within 2 days. Spruce transpiration was lower and relied more on snowmelt, because rainfall infiltration was low in the spruce stand due to high canopy interception. Our findings highlight the important role of snowmelt stored in the deep soil layers for subalpine forest drought response and the dominant fate of monsoonal rainfall to become transpiration rather than recharging groundwater and streams in the Upper Colorado River. Plain Language Summary There is a need to understand how trees in mountainous regions respond to dry conditions that lead to water scarcity, because climate projections suggest that such conditions will become more frequent in the future. Here we present a novel data set of measurements of daily stable isotopes of water across soil profiles and in tree stems of aspen and spruce. Our data show that when the upper soil dried out, aspen trees shifted to using water from deeper layers (beneath 60 cm) to keep transpiring. For spruce trees the uptake pattern is less clear, but both types of trees mainly used snowmelt stored in the deeper soil layers to survive the dry summer. After heavy rain, aspen and spruce trees switched to using water from the top 20 cm of soil. However, for spruce, only some rain reached the soil because the dense tree canopy intercepted it, so spruce trees stayed more dependent on snowmelt and used less water overall. This study shows how important deep snowmelt water is for helping forests survive dry periods and suggests that most summer rain is quickly used by trees rather than replenishing streams and groundwater in the headwaters of the Colorado River. Key Points Tree water resources changed within a few days from snow dominated to higher share of rainfall as soils wetted up after a dry period Compensatory plant water uptake by aspen from the deep layer (90 cm), while uptake from soil depths that became drier (60 cm) declined Strong differences between water sources and availability beneath aspen and spruce, respectively

Sprenger, Matthias↗
DOE OSTI2025

Ubiquity and Causes of Soil Water Preferential Flow Across 17 Ecoregions

Abstract Preferential flow (PF) in soil causes the rapid transport of water, nutrients, and contaminants into the subsurface, influencing groundwater recharge and streamflow. Data scarcity has hindered the quantification of PF occurrence and the identification of its drivers across diverse ecoregions. We address this gap by analyzing high‐frequency, multi‐depth soil moisture data across 17 ecoregions in the USA, using ∼1,500 sensors at 40 sites. We discovered that PF is widespread, with sites experiencing PF in up to 60% of rainfall events ≥2 mm. Multiple approaches consistently show that PF is more likely to occur with increased peak rainfall intensity, finer textured material, low soil moisture variability, humid climate, and higher net primary productivity. This suggests that PF patterns could shift with projected climate changes, increasing uncertainty in predictions of groundwater recharge, water quality, and streamflow generation. Plain Language Summary Water can bypass part of the soil's matrix through a process called preferential flow (PF). This quick transport of water through the soil brings with it nutrients and contaminants and eventually makes it to groundwater and streams. To ensure ample amounts of good quality groundwater and surface water we need to understand when and where PF occurs. We inferred when PF occurred at 40 different sites across 17 ecoregions in the USA using soil moisture and rainfall data. We found that PF happened at all sites and in up to 60% of rainfall events ≥2 mm. Preferential flow was most likely at sites with high rainfall intensities, high clay content in soils, low variability in soil moisture, and high vegetation productivity. As rainfall intensities are predicted to increase due to climate change and vegetation becomes more productive, PF occurrence becomes more important for predicting groundwater recharge, water quality, and streamflow generation. Key Points Preferential flow (PF) is ubiquitous across the USA and occurs in up to 60% of all rainfall events ≥2 mm Rainfall intensity, soil texture, and antecedent soil moisture emerge as critical in generating PF across diverse ecoregions Two different PF detection approaches show similar relationships between key drivers and occurrence of PF

Li, Bonan↗
DOE OSTI2022

Sulfide glass solid-state electrolyte separators for Li metal batteries: using an interlayer to increase rate performance and reduce stack pressure

We report on the solubility of (Li 2 S) 60 (SiS 2 ) x (P 2 S 5 ) 40–x , (0 ≤ x ≤ 40) sulfide glass solid-state electrolytes in the 1:1 (v/v) DME:DOL solvent mixture, a popular choice for lithium metal battery liquid electrolytes. SiS 2 -rich glasses within the compositional range of (Li 2 S) 60 (SiS 2 ) x (P 2 S 5 ) 40–x (28 ≤ x ≤ 40) were found to be functionally insoluble in DME:DOL. Hybrid symmetric test cells with a thin liquid electrolyte layer (0.6 M LiTFSI + 0.4 M LiNO 3 in 1:1 (v/v) DME:DOL) at the interface between lithium metal electrodes and an insoluble (Li 2 S) 60 (SiS 2 ) 28 (P 2 S 5 ) 12 glass wafer were tested. Hybrid test cells delivered a critical current density of 3.0 mA cm –2 at 25 °C and 0.1 MPa, which is nearly double the CCD of comparable dry symmetric test cells cycled at 10× higher stack pressure.

25 ENERGY STORAGE↗
DOE OSTI2021

Radioactive nuclei in the early Solar system: analysis of the 15 isotopes produced by core-collapse supernovae

Short-lived radioactive isotopes (SLRs) with half-lives between 0.1 and 100 Myr can be used to probe the origin of the Solar system. In this work, we examine the core-collapse supernovae production of the 15 SLRs produced: 26 Al, 36 Cl, 41 Ca, 53 Mn, 60 Fe, 92 Nb, 97 Tc, 98 Tc, 107 Pd, 126 Sn, 129 I, 135 Cs, 146 Sm, 182 Hf, and 205 Pb. Here, we probe the impact of the uncertainties of the core-collapse explosion mechanism by examining a collection of 62 core-collapse models with initial masses of 15, 20, and 25 M ⊙ , explosion energies between 3.4 × 10 50 and 1.8 × 10 52 erg and compact remnant masses between 1.5 and 4.89 M ⊙ . We identify the impact of both explosion energy and remnant mass on the final yields of the SLRs. Isotopes produced within the innermost regions of the star, such as 92 Nb and 97 Tc, are the most affected by the remnant mass, 92 Nb varying by five orders of magnitude. Isotopes synthesized primarily in explosive C-burning and explosive He-burning, such as 60 Fe, are most affected by explosion energies. 60 Fe increases by two orders of magnitude from the lowest to the highest explosion energy in the 15 M ⊙ model. The final yield of each examined SLR is used to compare to literature models.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Total cost of carbon capture and storage implemented at a regional scale: northeastern and midwestern United States

We model the costs of carbon capture and storage (CCS) in subsurface geological formations for emissions from 138 northeastern and midwestern electricity-generating power plants. The analysis suggests coal-sourced CO 2 emissions can be stored in this region at a cost of $52–$60 ton -1 , whereas the cost to store emission from natural-gas-fired plants ranges from approximately $80 to $90. Storing emissions offshore increases the lowest total costs of CCS to over $60 per ton of CO 2 for coal. Because there apparently is sufficient onshore storage in the northeastern and midwestern United States, offshore storage is not necessary or economical unless there are additional costs or suitability issues associated with the onshore reservoirs. For example, if formation pressures are prohibitive in a large-scale deployment of onshore CCS, or if there is opposition to onshore storage, offshore storage space could probably store emissions at an additional cost of less than $10 ton -1 . Finally, it is likely that more than 8 Gt of total CO 2 emissions from this region can be stored for less $60 ton -1 , slightly more than the $50 ton -1 Section 45Q tax credits incentivizing CCS.

Life Sciences & Biomedicine - Other Topics↗
DOE OSTI2021

Unveiling the mechanism of phase and morphology selections during the devitrification of Al-Sm amorphous ribbon

The complex interplay between energetic and kinetic factors that governs the phase and morphology selections can originate at the earliest stage of crystallization in the amorphous parent phases. Because of the extreme difficulties in capturing the microscopic nucleation process, a detailed picture of how initial disordered structures affect the transformation pathway remains unclear. Here, we report the experimental observation of widely varying phase selection and grain size evolution during the devitrification of a homogeneous melt-spun glassy ribbon. Two different crystalline phases, θ-Al 5 Sm and ε-Al 60 Sm 11 , are found to form in the different regions of the same metallic glass ribbon during the devitrification. The grain size of ε-Al 60 Sm 11 phase shows a strong spatial heterogeneity. Coarse-grained ε-Al 60 Sm 11 phase coupled with the small volume fraction of θ-Al 5 Sm phase is preferably formed close to wheel side of the melt-spun ribbon. Combining experimental characterization and computational simulations, we show that phase selection and microstructure evolution can be traced back to different types and populations of atomic clusters that serve as precursors for the nucleation of different crystalline phases. Inhomogeneous cooling rates cause different structure orders across the glass sample during the quenching process. Our findings provide direct insight into the effect of structural order on the crystallization pathways during the devitrification of metallic glass. It also opens an avenue to study the detailed nucleation process at the atomic level using the metallic glass as a platform and suggests the opportunity of microstructure and property design via controlling the cooling process.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Impedance Scan of Inverter-Based Resources and Diesel Generator for Stability Analysis

Impedance-based methods are widely used for power system stability analysis with inverter-based resources (IBRs), e.g., assessing dynamic interactions between the power grid and an IBR, control interactions between multiple IBRs, and the sub-synchronous oscillation and damping phenomenon. Since it is difficult to get a numerical model 100% matching with the hardware IBR, using the hardware inverter directly to obtain its output impedance has become a prominent approach nowadays. Therefore, this article presents the impedance scan using hardware IBRs, and also a hardware diesel generator as it still stays with the grid before the grid completely goes to renewable. The devices under test (DuTs) for the impedance scan includes two 3-..phi.., 480 V, 60 Hz commercial grid-forming IBRs (one of 250 kVA and another of 125 kVA rating) in series with ..delta..-Y transformers, one 3-..phi.., 480 V, 60 Hz commercial grid-following IBR (of 125 kVA rating), and a 3-..phi.., 480 V, 60 Hz commercial diesel generator (of 187.5 kVA rating). Using voltage signals perturbed with sub-, inter-, and higher harmonic components, and measuring the current response, the positive-sequence impedances are computed via an offline-based post-analysis. Moreover, best-fit transfer functions are estimated that closely resemble the measured data points of the positive-sequence impedances. Based on the observations from various outcomes of the hardware experiments, this article also provides some fundamental insights on the equivalent positive-sequence impedance of a combination of multiple hardware components by comparing the estimated and the empirically computed impedances. A comparative insight on the damping capability of the DuTs using the positive-sequence impedances of the hardware is also discussed.

current measurement↗