Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRCRAFT ACCIDENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Piloted simulation tests of propulsion control as backup to loss of primary flight controls for a mid-size jet transport

Failures of aircraft primary flight-control systems to aircraft during flight have led to catastrophic accidents with subsequent loss of lives (e.g. , DC-1O crash, B-747 crash, C-5 crash, B-52 crash, and others). Dryden Flight Research Center (DFRC) investigated the use of engine thrust for emergency flight control of several airplanes, including the B-720, Lear 24, F-15, C-402, and B-747. A series of three piloted simulation tests have been conducted at Ames Research Center to investigate propulsion control for safely landing a medium size jet transport which has experienced a total primary flight-control failure. The first series of tests was completed in July 1992 and defined the best interface for the pilot commands to drive the engines. The second series of tests was completed in August 1994 and investigated propulsion controlled aircraft (PCA) display requirements and various command modes. The third series of tests was completed in May 1995 and investigated PCA full-flight envelope capabilities. This report describes the concept of a PCA, discusses pilot controls, displays, and procedures; and presents the results of piloted simulation evaluations of the concept by a cross-section of air transport pilots.

Bull, John↗

Neural Flight Control System

The Neural Flight Control System (NFCS) was developed to address the need for control systems that can be produced and tested at lower cost, easily adapted to prototype vehicles and for flight systems that can accommodate damaged control surfaces or changes to aircraft stability and control characteristics resulting from failures or accidents. NFCS utilizes on a neural network-based flight control algorithm which automatically compensates for a broad spectrum of unanticipated damage or failures of an aircraft in flight. Pilot stick and rudder pedal inputs are fed into a reference model which produces pitch, roll and yaw rate commands. The reference model frequencies and gains can be set to provide handling quality characteristics suitable for the aircraft of interest. The rate commands are used in conjunction with estimates of the aircraft s stability and control (S&C) derivatives by a simplified Dynamic Inverse controller to produce virtual elevator, aileron and rudder commands. These virtual surface deflection commands are optimally distributed across the aircraft s available control surfaces using linear programming theory. Sensor data is compared with the reference model rate commands to produce an error signal. A Proportional/Integral (PI) error controller "winds up" on the error signal and adds an augmented command to the reference model output with the effect of zeroing the error signal. In order to provide more consistent handling qualities for the pilot, neural networks learn the behavior of the error controller and add in the augmented command before the integrator winds up. In the case of damage sufficient to affect the handling qualities of the aircraft, an Adaptive Critic is utilized to reduce the reference model frequencies and gains to stay within a flyable envelope of the aircraft.

Gundy-Burlet, Karen↗

General Aviation Pilots' Perceived Usage and Valuation of Aviation Weather Information Sources

Aviation suffers many accidents due to the lack of good weather information in flight. Existing aviation weather information is difficult to obtain when it is most needed and is not well formatted for in-flight use. Because it is generally presented aurally, aviation weather information is difficult to integrate with spatial flight information and retain for reference. Efforts, by NASA's Aviation Weather Information (AWIN) team and others, to improve weather information accessibility, usability and decision aiding will enhance General Aviation (GA) pilots' weather situation awareness and decision-making and therefore should improve the safety of GA flight. Consideration of pilots' economic concerns will ensure that in-flight weather information systems are financially accessible to GA pilots as well. The purpose of this survey was to describe how aviation operator communities gather and use weather information as well as how weather related decisions are made between flight crews and supporting personnel. Pilots of small GA aircraft experience the most weather-related accidents as well as the most fatal weather related accident. For this reason, the survey design and advertisement focused on encouraging participation from GA pilots. Perhaps as a result of this emphasis, most responses, 97 responses or 85% of the entire response set, were from GA pilots, This paper presents only analysis of these GA pilots' responses. The insights provided by this survey regarding GA pilots' perceived value and usage of current aviation weather information. services, and products provide a basis for technological approaches to improve GA safety. Results of this survey are discussed in the context of survey limitations and prior work, and serve as the foundation for a model of weather information value, guidance for the design of in-flight weather information systems, and definition of further research toward their development.

Latorella, Kara↗

Factors that Influenced Airplane State Awareness Accidents and Incidents: CAST SE-210 Output 2: Report 2 of 6

This report is part of a series of reports that address flight deck design and evaluation, written as a response to loss of control accidents. In particular, this activity is directed at failures in airplane state awareness in which the pilot loses awareness of the airplane’s energy state or attitude and enters an upset condition. The Commercial Aviation Safety Team (CAST) created a team to analyze a set of incidents and accidents associated with the flight crew’s loss of awareness of aircraft attitude or energy state. The CAST activity focused on a set of 18 loss of control (LOC) accidents and incidents. In those events, the pilot seemed to lose awareness of the state of the airplane, especially related to its energy state or its attitude. To understand the roots of that loss of awareness, we analyzed the events in relation to a set of factors that were present in many of them. We show how these factors contributed to lost awareness. Then, we use that understanding to identify potentially useful changes to the flight deck interface and how those flight deck changes could be evaluated.

commercial aviation↗

An Application of CICCT Accident Categories to Aviation Accidents in 1988-2004

Interventions or technologies developed to improve aviation safety often focus on specific causes or accident categories. Evaluation of the potential effectiveness of those interventions is dependent upon mapping the historical aviation accidents into those same accident categories. To that end, the United States civil aviation accidents occurring between 1988 and 2004 (n=26,117) were assigned accident categories based upon the taxonomy developed by the CAST/ICAO Common Taxonomy Team (CICTT). Results are presented separately for four main categories of flight rules: Part 121 (large commercial air carriers), Scheduled Part 135 (commuter airlines), Non-Scheduled Part 135 (on-demand air taxi) and Part 91 (general aviation). Injuries and aircraft damage are summarized by year and by accident category.

Evans, Joni K.↗

Factors influencing tolerance to wind shears in landing approach

Flight simulator studies were conducted to examine the piloting problems resulting from encounters with unusual atmospheric disturbances late in landing approach. Simulated encounters with disturbances, including examples derived from accident data, provided the opportunity to study aircraft and pilot performance. It was observed that substantial delays in pilot response to shear-induced departures from glide slope often seriously amplified the consequences of the encounter. In preliminary assessments, an integrated flight instrument display featuring flight path as the primary controlled element appeared to provide the means to minimize such delays by improving tolerance to disturbances in landing approaches.

Bray, R. S.↗

Microbursts as an aviation wind shear hazard

The downburst-related accidents or near-misses of jet aircraft have been occurring at the rate of once or twice a year since 1975. A microburst with its field comparable to the length of runways can induce a wind shear which endangers landing or liftoff aircraft; the latest near miss landing of a 727 aircraft at Atlanta, Ga. in 1979 indicated that some microbursts are too small to trigger the warning device of the anemometer network at major U.S. airports. The nature of microbursts and their possible detection by Doppler radar are discussed, along with proposed studies of small-scale microbursts.

Fujita, T. T.↗

Diagnosis and Reconfiguration using Bayesian Networks: An Electrical Power System Case Study

Automated diagnosis and reconfiguration are important computational techniques that aim to minimize human intervention in autonomous systems. In this paper, we develop novel techniques and models in the context of diagnosis and reconfiguration reasoning using causal Bayesian networks (BNs). We take as starting point a successful diagnostic approach, using a static BN developed for a real-world electrical power system. We discuss in this paper the extension of this diagnostic approach along two dimensions, namely: (i) from a static BN to a dynamic BN; and (ii) from a diagnostic task to a reconfiguration task. More specifically, we discuss the auto-generation of a dynamic Bayesian network from a static Bayesian network. In addition, we discuss subtle, but important, differences between Bayesian networks when used for diagnosis versus reconfiguration. We discuss a novel reconfiguration agent, which models a system causally, including effects of actions through time, using a dynamic Bayesian network. Though the techniques we discuss are general, we demonstrate them in the context of electrical power systems (EPSs) for aircraft and spacecraft. EPSs are vital subsystems on-board aircraft and spacecraft, and many incidents and accidents of these vehicles have been attributed to EPS failures. We discuss a case study that provides initial but promising results for our approach in the setting of electrical power systems.

Knox, W. Bradley↗

Sixty-four-Channel Inline Cable Tester

Faults in wiring are a serious concern for the aerospace and aeronautics (commercial, military, and civil) industries. A number of accidents have occurred because faulty wiring created shorts or opens that resulted in the loss of control of the aircraft or because arcing led to fires and explosions. Some of these accidents have resulted in the massive loss of lives (such as in the TWA Flight 800 accident). Circuits on the Space Shuttle have also failed because of faulty insulation on wiring. STS-93 lost power when a primary power circuit in one engine failed and a second engine had a backup power circuit fault. Cables are usually tested on the ground after the crew reports a fault encountered during flight. Often such failures result from vibration and cannot be replicated while the aircraft is stationary. It is therefore important to monitor faults while the aircraft is in operation, when cables are more likely to fail. Work is in progress to develop a cable fault tester capable of monitoring up to 64 individual wires simultaneously. Faults can be monitored either inline or offline. In the inline mode of operation, the monitoring is performed without disturbing the normal operation of the wires under test. That is, the operations are performed unintrusively and are essentially undetectable for the test signal levels are below the noise floor. A cable can be monitored several times per second in the offline mode and once a second in the inline mode. The 64-channel inline cable tester not only detects the occurrence of a fault, but also determines the type of fault (short/open) and the location of the fault. This will enable the detection of intermittent faults that can be repaired before they become serious problems.

Source record↗

Recommendations for Injury Prevention in Transport Aviation Accidents

In 1996, a national objective was established to reduce the rate of fatal accidents in aviation. To assist in determining the best methods for improving aircraft crash survivability, a combined approach was used involving database research and the examination of case studies of transport aviation accidents. The results of the study include recommendations for maintaining occupiable space, enhancing occupant restraint, managing energy transferred to the occupant, improving egress, and increasing post-crash survival.

Grierson, Anita E.↗

Foam Cushioning

One innovation developed by a contractor at Ames Research Center was an open cell polymeric foam material with unusual properties. Intended as padding for aircraft seats the material offered better impact protection against accidents, and also enhanced passenger comfort because it distributed body weight evenly over the entire contact area. Called a slow springback foam, it flows to match the contour of the body pressing against it, and returns to its original shape once the pressure is removed. It has many applications including aircraft cushions and padding, dental stools, and athletic equipment. Now it's used by Dynamic Systems, Inc. for medical applications such as wheel chairs for severely disabled people which allow them to sit for 3-8 hours where they used to be uncomfortable in 15-30 minutes.

Source record↗

Flight Testing of In-Time Safety Assurance Technologies for UAS Operations

Ongoing research at NASA is driven by a strategic plan defined by the Aeronautics Research Mission Directorate and a vision for future In-Time Aviation Safety Management Systems (IASMS) as described by the National Academies. In both visions, system safety awareness and provision are expanded through increased access to relevant data; integrated analysis and predictive capabilities; improved real-time detection and alerting of domain-specific hazards; decision support, and in some cases, automated risk mitigation strategies. One primary research focus is to develop means by which more timely (i.e., “in-time”) actions may be taken to mitigate precursors, anomalies, or trends that are observed during operations. In this paper, we describe such means as a collection of Services, Functions, and Capabilities (SFCs) that are supported by an underlying information system. For example, an integrated risk assessment capability is envisioned that continuously monitors safety-related metrics and margins and recommends timely operational changes. Assessment functions and/or services can be based on data analytics and predictive models derived from heterogeneous data sets that span relevant indicator metrics and their time histories. Likewise, on-board functions can identify and reduce susceptibility to precursor conditions that have led (and can lead) to aircraft loss-of-control or out-of-control accidents. This paper summarizes development and testing of such an information system tailored to hazards anticipated for future highly autonomous flight missions near and over densely populated areas. Testing is accomplished via simulation and by using small, unmanned aircraft operating over a test range at NASA’s Langley Research Center. Flight plans and test scenarios are defined to emulate several use-cases, including package delivery; reconnaissance; fire management; and urban air taxi vertiport operations. Two test phases are summarized with Phase 1 occurring in (2019-2020) and Phase 2 ongoing (2021-present). Results focus on SFC performance, technology readiness level assessment, and requirements discovery/validation. Companion papers are cited throughout for additional details on the recent testing.

safety management↗

A mathematical model for efficient estimation of aircraft motions

In the usual formulation of the aircraft state-estimation problem, motions along a flight trajectory are represented by a plant consisting of nonlinear state and measurement models. Problem solution using this formulation requires that both state- and measurement-dependent Jacobian matrices be evaluated along any trajectory. In this paper it is shown that a set of state variables can be chosen to realize a linear state model of very simple form, such that all nonlinearities appear in the measurement model. The potential advantage of the new formulation is computational: the Jacobian matrix corresponding to a linear state model is constant, a feature that should outweigh the fact that the measurement model is more complicated than in the conventinal formulation. To compare the modeling methods, aircraft motions from typical flight-test and accident data were estimated, using each formulation with the same off-line (smoothing) algorithm. The results of these experiments, reported in the paper, demonstrate clearly the computational superiority of the linear state-variable formulation. The procedure advocated here may be extended to other nonlinear estimation problems, including on-line (filtering) applications.

Bach, R. E., Jr.↗

Accident investigation

The National Transportation Safety Board (NTSB) has attributed wind shear as a cause or contributing factor in 15 accidents involving transport-categroy airplanes since 1970. Nine of these were nonfatal; but the other six accounted for 440 lives. Five of the fatal accidents and seven of the nonfatal accidents involved encounters with convective downbursts or microbursts. Of other accidents, two which were nonfatal were encounters with a frontal system shear, and one which was fatal was the result of a terrain induced wind shear. These accidents are discussed with reference to helping the aircraft to avoid the wind shear or if impossible to help the pilot to get through the wind shear.

Laynor, William G. Bud↗

Weather data dissemination to aircraft

Documentation exists that shows weather to be responsible for approximately 40 percent of all general aviation accidents with fatalities. Weather data products available on the ground are becoming more sophisticated and greater in number. Although many of these data are critical to aircraft safety, they currently must be transmitted verbally to the aircraft. This process is labor intensive and provides a low rate of information transfer. Consequently, the pilot is often forced to make life-critical decisions based on incomplete and outdated information. Automated transmission of weather data from the ground to the aircraft can provide the aircrew with accurate data in near-real time. The current National Airspace System Plan calls for such an uplink capability to be provided by the Mode S Beacon System data link. Although this system has a very advanced data link capability, it will not be capable of providing adequate weather data to all airspace users in its planned configuration. This paper delineates some of the important weather data uplink system requirements, and describes a system which is capable of meeting these requirements. The proposed system utilizes a run-length coding technique for image data compression and a hybrid phase and amplitude modulation technique for the transmission of both voice and weather data on existing aeronautical Very High Frequency (VHF) voice communication channels.

Mcfarland, Richard H.↗

Unsafe acts and unsafe outcomes in aircraft maintenance

Road safety studies using the Driver Behaviour Questionnaire (DBQ) have provided support for a three-way distinction between violations, skill-based errors and mistakes, and have indicated that a tendency to commit driving violations is associated with an increased risk of accident involvement. The aims of this study were to examine whether the three-way distinction of unsafe acts is applicable in the context of aircraft maintenance, and whether involvement in maintenance safety occurrences can be predicted on the basis of self-reported unsafe acts. A Maintenance Behaviour Questionnaire (MBQ) was developed to explore patterns of unsafe acts committed by aircraft maintenance mechanics. The MBQ was completed anonymously by over 1300 Australian aviation mechanics, who also provided information on their involvement in workplace accidents and incidents. Four factors were identified: routine violations, skill-based errors, mistakes and exceptional violations. Violations and mistakes were related significantly to the occurrence of incidents that jeopardized the quality of aircraft maintenance, but were not related to workplace injuries. Skill-based errors, while not related to work quality incidents, were related to workplace injuries. The results are consistent with the three-way typology of unsafe acts described by Reason et al. (1990) and with the DBQ research indicating an association between self-reported violations and accidents. The current findings suggest that interventions addressed at maintenance quality incidents should take into account the role of violations and mistakes, and the factors that promote them. In contrast, interventions directed at reducing workplace injury are likely to require a focus on skill-based errors.

Maintenance/manpower/methods↗

A Probability-Base Alerting Logic for Aircraft on Parallel Approach

This document discusses the development and evaluation of an airborne collision alerting logic for aircraft on closely-spaced approaches to parallel runways. A novel methodology is used when links alerts to collision probabilities: alerting thresholds are set such that when the probability of a collision exceeds an acceptable hazard level an alert is issued. The logic was designed to limit the hazard level to that estimated for the Precision Runway Monitoring system: one accident in every one thousand blunders which trigger alerts. When the aircraft were constrained to be coaltitude, evaluations of a two-dimensional version of the alerting logic show that the achieved hazard level is approximately one accident in every 250 blunders. Problematic scenarios have been identified and corrections to the logic can be made. The evaluations also show that over eighty percent of all unnecessary alerts were issued during scenarios in which the miss distance would have been less than 1000 ft, indicating that the alerts may have been justified. Also, no unnecessary alerts were generated during normal approaches.

Carpenter, Brenda D.↗

Aircraft Loss of Control: Problem Analysis for the Development and Validation of Technology Solutions

Aircraft loss of control (LOC) is a leading cause of fatal accidents across all transport airplane and operational classes. LOC can result from a wide spectrum of precursors (or hazards), often occurring in combination. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of conditions and uncertainties, including multiple hazards, and the validation process must provide a means of assessing system effectiveness and coverage of these hazards. This paper provides a detailed description of a methodology for analyzing LOC as a dynamics and control problem for the purpose of developing effective technology solutions. The paper includes a definition of LOC based on several recent publications, a detailed description of a refined LOC accident analysis process that is illustrated via selected example cases, and a description of planned follow-on activities for identifying future potential LOC risks and the development of LOC test scenarios. Some preliminary considerations for LOC of Unmanned Aircraft Systems (UAS) and for their safe integration into the National Airspace System (NAS) are also discussed.

Belcastro, Christine M.↗