Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

The effect of multiple fixed slots and a trailing-edge flap on the lift and drag of a Clark Y airfoil

Lift and drag tests were made on a Clark Y wing equipped with four fixed slots and a trailing-edge flap in the 5-foot vertical wind tunnel of the National Advisory Committee for Aeronautics. All possible combinations of the four slots were tested with the flap neutral and the most promising combinations were tested with the flap down 45 degrees. Considering both the maximum lift coefficient and the speed-range ratio with the flap neutral no appreciable improvement was found with the use of more than the single leading-edge slot. With the flap down 45 degrees a maximum lift coefficient of 2.60 was obtained but the particular slot combination used had a rather large minimum drag coefficient with the flap neutral. With the flap down 45 degrees the optimum combination, considering both the maximum lift coefficient and the speed-range ratio, was obtained with only the two rearmost slots in use. For this arrangement the maximum lift coefficient was 2.44.

Weick, Fred E↗
NASA NTRS1977

Modelling techniques for jet impingement

A technique for testing scale models for the determination of fluctuating pressure loads due to jet impingement has been investigated using a quarter-scale model of a boilerplate test facility in which a JT-15D engine with a rectangular outer nozzle blows over a small curved airfoil representing the upper-surface of a wing. When model and full-scale spectra of fluctuating surface pressures are reduced to plots of pressure coefficient power-spectral density vs Strouhal number, moderate agreement is obtained, but a shift of spectral peaks is noted. However, when a correction for the ratio of average jet to ambient temperature is applied, the spectral peaks agree.

Haviland, J. K.↗
NASA NTRS1981

Calculations of transonic potential flow over cascades

Transonic flow through a cascade was studied by using the full potential equation and the finite volume method of Jameson and Caughey. The C-type computational grid is generated by an electrostatic analogy and simple shearing transformation. The solution algorithm includes an option of using either an artificial density or an artificial viscosity formulation of the dissipative term. Using the developed code, flows through a cascade of NACA 0012 airfoils and flows through a cascade of shockless blades were computed. It is found that the designed flow through the shockless blade is accurately predicted, the artificial density formulation shows more tolerance to the mesh irregularity, and the C-type mesh does not extend very far upstream for a small pitch-cord ratio.

Jou, W. H.↗
NASA NTRS1986

Transonic interference reduction by limited ventilation wall panels

In two wind tunnels used for the two-dimensional airfoil tests, each wall above and below the model was modified by replacing small segments of the solid boundaries with perforated plates vented into sealed chambers. Perforated segments having approximately 40 percent open area were found to reduce the transonic wall interference to a negligible level, for a model chord-to-tunnel height ratio of 0.5. This report describes the physical arrangement and presents typical model pressure distributions to illustrate the effectiveness of the technique.

Lee, John D.↗
NASA NTRS1989

An experimental study of turbine vane heat transfer with leading edge and downstream film cooling

This paper presents the effects of downstream film cooling, with and without leading edge showerhead film cooling, on turbine-vane external heat transfer. Steady-state experimental measurements were made in a three-vane linear two-dimensional cascade. The principal independent parameters were maintained over ranges consistent with actual engine conditions. The test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. The data obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The downstream film cooling process was shown to be a complex interaction of two competing mechanisms. The thermal dilution effect, associated with the injection of relatively cold fluid, results in a decrease in the heat transfer to the airfoil. Conversely, the turbulence augmentation, produced by the injection process, results in increased heat transfer to the airfoil.

Nirmalan, V.↗
NASA NTRS1971

An experimental investigation of the helicopter rotor blade element airloads on a model rotor in the blade stall regime

A wind tunnel test program was conducted on an eight foot diameter model rotor system to determine blade element airloads characteristics in the unstalled and stalled flight regimes. The fully articulated model rotor system utilized three blades with a Vertol 23010-1.58 airfoil section, the blades being 1/7.5 scale models of the Ch-47C rotor blades. Instrumentation was incorporated at the blade 75% radial station to measure pressure and skin friction distributions, surface streamline directions and local angle of attack. The test program was conducted in three phases; non-rotating, hover and forward flight at advance ratios of 0.15, 0.35 and 0.60. Test data were analyzed with respect to providing insight to the mechanisms affecting blade stall, particularly retreating blade stall during forward flight conditions. From such data, an assessment was made as to the applicability of current theoretical analyses used for the prediction of blade element airloads in the stall regime.

Fisher, R. K., Jr.↗
NASA NTRS1948

The effectiveness at high speeds of a 10-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section

This report contains the results of a high-speed wind-tunnel investigation of the effectiveness of a 10-percent-chord plain flap on the NACA 65-210 airfoil section. The results include an indication of the lift-producing characteristics and the effectiveness of the 10-percent-chord flap. From a comparison of the characteristics of the 10-percent-chord flap with those of a 20-percent-chord flap it was concluded that, although a reduction in flap-chord ratio from 0.20 to 0.10 lessens the severity of the effectiveness loss at supercritical speeds, the 20-percent-chord flap is more effective throughout the entire range of Mach numbers from 0.3 to 0.875.

CONTROLS, FLAP TYPE - WING SECTIONS↗
NASA NTRS1973

A method for predicting shock shapes and pressure distributions on two dimensional airfoils at large angles of attack

A method is presented for determining shock envelopes and pressure distributions for two-dimensional airfoils at angles of attack sufficiently large to cause shock detachment and subsonic flow over the windward surface of the airfoil. Correlation functions obtained from exact solutions are used to relate the shock standoff distance at the stagnation and sonic points of the body through a suitable choice for the shock shape. The necessary correlation functions were obtained from perfect gas solutions but may be extended to any gas flow for which the normal shock-density ratio can be specified.

Kaattari, G. E.↗
NASA NTRS1980

Investigation of performance deterioration of the CF6/JT9D, high-bypass ratio turbofan engines

The aircraft energy efficiency program within NASA is developing technology required to improve the fuel efficiency of commercial subsonic transport aricraft. One segment of this program includes engine diagnostics which is directed toward determining the sources and causes of performance deterioration in the Pratt and Whitney Aircraft JT9D and General Electric CF6 high-bypass ratio turbofan engines and developing technology for minimizing the performance losses. Results of engine performance deterioration investigations based on historical data, special engine tests, and specific tests to define the influence of flight loads and component clearances on performance are presented. The results of analysis of several damage mechanisms that contribute to performance deterioration such as blade tip rubs, airfoil surface roughness and erosion, and thermal distortion are also included. The significance of these damage mechanisms on component and overall engine performance is discussed.

Ziemianski, J. A.↗
NASA NTRS1985

An evaluation of three helicopter rotor sections

Three helicopter rotor sections were tested in the NASA Ames Research Center 2- by 2-Foot Transonic Wind Tunnel over a Mach range from 0.2 to 0.88. The sections tested had maximum thickness/chord ratios of 0.078, 0.09, and 0.10. The thickest section was of early technology and had been tested previously in other wind tunnels. This section was included in the investigation to establish a basis for comparing the two thinner sections, which were of recent design. The results of the investigation showed that the pitching-moment characteristics for the three airfoil sections were acceptable. The drag divergence Mach numbers for the three sections were 0.80, 0.825, and 0.845 in order of decreasing thickness.

Hicks, R. M.↗
NASA NTRS1984

Implementation of uniform perturbation method for potential flow past axisymmetric and two-dimensional bodies

The aerodynamic characteristics of potential flow past an axisymmetric slender body and a thin airfoil are calculated using a uniform perturbation analysis method. The method is based on the superposition of potentials of point singularities distributed inside the body. The strength distribution satisfies a linear integral equation by enforcing the flow tangency condition on the surface of the body. The complete uniform asymptotic expansion of its solution is obtained with respect to the slenderness ratio by modifying and adapting an existing technique. Results calculated by the perturbation analysis method are compared with the existing surface singularity panel method and some available analytical solutions for a number of cases under identical conditions. From these comparisons, it is found that the perturbation analysis method can provide quite accurate results for bodies with small slenderness ratio. The present method is much simpler and requires less memory and computation time than existing surface singularity panel methods of comparable accuracy.

Wong, T. C.↗
NASA NTRS1929

Wind tunnel tests on airfoil boundary control using a backward opening slot

This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil equipped with a backward opening slot. Various slot locations, widths of opening, and pressures, were used. The tests were conducted in the Five-Foot Atmospheric Wind Tunnel of the Langley Memorial Aeronautical Laboratory. The greatest increase in maximum lift was 96 per cent, the greatest decrease in minimum drag was 27 per cent, and the greatest increase in the ratio, maximum lift coefficient/minimum drag coefficient, was 151 per cent.

Knight, Montgomery↗
NASA NTRS1988

Energy Efficient Engine: High-pressure compressor test hardware detailed design report

The objective of the NASA Energy Efficient Engine program is to identify and verify the technology required to achieve significant reductions in fuel consumption and operating cost for future commercial gas turbine engines. The design and analysis is documented of the high pressure compressor which was tested as part of the Pratt and Whitney effort under the Energy Efficient Engine program. This compressor was designed to produce a 14:1 pressure ratio in ten stages with an adiabatic efficiency of 88.2 percent in the flight propulsion system. The corresponding expected efficiency for the compressor component test rig is 86.5 percent. Other performance goals are a surge margin of 20 percent, a corrected flow rate of 35.2 kg/sec (77.5 lb/sec), and a life of 20,000 missions and 30,000 hours. Low loss, highly loaded airfoils are used to increase efficiency while reducing the parts count. Active clearance control and case trenches in abradable strips over the blade tips are included in the compressor component design to further increase the efficiency potential. The test rig incorporates variable geometry stator vanes in all stages to permit maximum flexibility in developing stage-to-stage matching. This provision precluded active clearance control on the rear case of the test rig. Both the component and rig designs meet or exceed design requirements with the exception of life goals, which will be achievable with planned advances in materials technology.

Howe, David C.↗
NASA NTRS1956

Aerodynamic Design of Axial-flow Compressors. Volume III

Chapters XI to XIII concern the unsteady compressor operation arising when compressor blade elements stall. The fields of compressor stall and surge are reviewed in Chapters XI and XII, respectively. The part-speed operating problem in high-pressure-ratio multistage axial-flow compressors is analyzed in Chapter XIII. Chapter XIV summarizes design methods and theories that extend beyond the simplified two-dimensional approach used previously in the report. Chapter XV extends this three-dimensional treatment by summarizing the literature on secondary flows and boundary layer effects. Charts for determining the effects of errors in design parameters and experimental measurements on compressor performance are given in Chapters XVI. Chapter XVII reviews existing literature on compressor and turbine matching techniques.

COMPRESSORS - PRESSURE RATIO↗
NASA NTRS2003

Numerical Simulations of the Steady and Unsteady Aerodynamic Characteristics of a Circulation Control Wing Airfoil

The aerodynamic characteristics of a Circulation Control Wing (CCW) airfoil have been numerically investigated, and comparisons with experimental data have been made. The configuration chosen was a supercritical airfoil with a 30 degree dual-radius CCW flap. Steady and pulsed jet calculations were performed. It was found that the use of steady jets, even at very small mass flow rates, yielded a lift coefficient that is comparable or superior to conventional high-lift systems. The attached flow over the flap also gave rise to lower drag coefficients, and high L/D ratios. Pulsed jets with a 50% duty cycle were also studied. It was found that they were effective in generating lift at lower reduced mass flow rates compared to a steady jet, provided the pulse frequency was sufficiently high. This benefit was attributable to the fact that the momentum coefficient of the pulsed jet, during the portions of the cycle when the jet was on, was typically twice as much as that of a steady jet.

Liu, Yi↗
NASA NTRS1985

Numerical solution of the full-potential equation for rotors and oblique wings using a new wake model

A three-dimensional, full-potential, quasi-steady code TFAR1 is proposed for calculating the transonic flow past a lifting helicopter rotor blade and oblique wing. The TFAR1 uses a two-dimensional nonlinear wake-model that allows a jump in velocity potential to propagate with the local fluid flow in the wake. Rotor calculations were made for a single blade at an advance ratio of 0.3, a rotational tip Mach number of 0.7, and at 0-degree incidence. A 1/7-scale model of the Cobra Operational Load Survey (OLS) rotor blade is calculated, and the pressure distributions are compared to the measurements for azimuth angles 0, 30, 60, 90, 120, and 150 degrees at the 95 percent spanwise station of the OLS blade. Furthermore, an oblique wing with Korn airfoil was calculated at the high transonic free-stream Mach number of 0.9791, zero incidence, and yaw angle of 40 degrees. The TFAR1, coupled with a helicopter performance code CAMRAD (Johnson, 1981), provides a full-potential code for calculating the entire flow field for a multiple-bladed rotor in transonic lifting forward flight.

Chang, I.-C.↗
NASA NTRS1944

Wall interference in a two-dimensional-flow wind tunnel, with consideration of the effect of compressibility

Theoretical tunnel-wall corrections are derived for an airfoil of finite thickness and camber in a two-dimensional-flow wind tunnel. The theory takes account of the effects of the wake of the airfoil and of the compressibility of the fluid, and is based upon the assumption that the chord of the airfoil is small in comparison with the height of the tunnel. Consideration is given to the phenomenon of choking at high speeds and its relation to the tunnel-wall corrections. The theoretical results are compared with the small amount of low-speed experimental data available and the agreement is seen to be satisfactory, even for relatively large values of the chord-height ratio.

Allen, H Julian↗
NASA NTRS1982

Flow distributions and discharge coefficient effects for jet array impingement with initial crossflow

To model the impingement cooled mid-chord region of gas turbine airfoils in cases where an initial crossflow is present, the paper presents experimentally determined flow distributions for jet arrays with ten spanwise rows of holes, which range from uniform to highly nonuniform. The jet flow after impingement is constrained to exit in a single direction along the channel formed by the jet orifice plate and the impingement surface. The streamwise distributions and crossflow velocities are presented for ratios of the initial crossflow rate to the total jet flow rate ranging from zero to unity. For crossflow to jet velocity ratios greater than a value somewhat less than unity, jet orifice discharge coefficients do not remain constant, but decrease significantly, showing a secondary dependence on z/d, where z is the channel height and d is the jet hole diameter.

Florschuetz, L. W.↗