Search NASA⌕ Search

SEARCH · Search NASA

Results for “Activity coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Comparison of gasification kinetics parameters of different types of nuclear graphite

A chemical-reaction kinetics model of nuclear graphite gasification has recently been developed and successfully validated with gasification rate measurements for nuclear graphite grades of IG-110, IG-430, NBG-18 and NBG-25. The model employs 4 elementary chemical reactions with applicable parameters, including the values and Gaussian-like distributions of the specific activation energies, the pre-exponential coefficients for adsorption of oxygen and desorption of CO and CO{sub 2} gases, and the surface area of free active sites. These parameters are determined from the reported measurements of the total gasification and transient weight loss using a multi-parameter optimization algorithm. The determined chemical kinetics parameters for IG-100 and NB-25 are nearly the same, but slightly different from those for NBG-18 and IG-430. The initial specific area of free active sites is inversely proportional to the square root of the mass or volume of the graphite specimens used in experiments. The recommended chemical kinetics parameters in this paper for these grades of nuclear graphite should be applicable to future safety analysis of high-temperature gas cooled reactors in the unlikely event of a massive air ingress accident. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

ANALYSIS ON CORRELATIONS BETWEEN SUBSURFACE KINETIC HELICITY AND PHOTOSPHERIC CURRENT HELICITY IN ACTIVE REGIONS

An investigation on correlations between photospheric current helicity and subsurface kinetic helicity is carried out by analyzing vector magnetograms and subsurface velocities for two rapidly developing active regions. The vector magnetograms are from the Solar Dynamics Observatory/Helioseismic and Magnetic Imager (SDO/HMI) observed Stokes parameters, and the subsurface velocity is from time-distance data-analysis pipeline using HMI Dopplergrams. Over a span of several days, the evolution of the weighted current helicity shows a tendency similar to that of the weighted subsurface kinetic helicity, attaining a correlation coefficient above 0.60 for both active regions. Additionally, there seems to be a phase lag between the evolutions of the unweighted current and subsurface kinetic helicities for one of the active regions. The good correlation between these two helicities indicates that there is some intrinsic connection between the interior dynamics and photospheric magnetic twistedness inside active regions, which may help to interpret the well-known hemispheric preponderance of current-helicity distribution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hall and transverse even effects in the vicinity of a quantum critical point in Tm{sub 1-x}Yb{sub x}B{sub 12}

The angular, temperature, and magnetic field dependences of the resistance recorded in the Hall effect geometry are studied for the rare-earth dodecaboride Tm{sub 1-x}Yb{sub x}B{sub 12} solid solutions where the metal-insulator and antiferromagnetic-paramagnetic phase transitions are observed in the vicinity of the quantum critical point x{sub c} Almost-Equal-To 0.3. The measurements performed on high-quality single crystals in the temperature range 1.9-300 K for the first time have revealed the appearance of the second harmonic contribution, a transverse even effect in these fcc compounds near the quantum critical point. This contribution a is found to increase drastically both under the Tm-to-ytterbium substitution in the range x > x{sub c} and with an increase in the external magnetic field. Moreover, as the Yb concentration x increases, a negative peak of a significant amplitude appears on the temperature dependences of the Hall coefficient R{sub H}(T) for the Tm{sup 1-x}Yb{sub x}B{sub 12} compounds, in contrast to the invariable behavior R{sub H}(T) Almost-Equal-To const found for TmB{sub 12}. The complicated activation-type behavior of the Hall coefficient is observed at intermediate temperatures for x {>=} 0.5 with activation energies E{sub g}/k{sub B} Almost-Equal-To 200 K and E{sub a}/k{sub B} 55-75 K, and the sign inversion of R{sub H}(T) is detected at liquid-helium temperatures in the coherent regime. Renormalization effects in the electron density of states induced by variation of the Yb concentration are analyzed. The anomalies of the charge transport in Tm{sub 1-x}Yb{sub x}B{sub 12} solid solutions in various regimes (charge gap formation, intra-gap many-body resonance, and coherent regime) are discussed in detail and the results are interpreted in terms of the electron phase separation effects in combination with the formation of nanosize clusters of rare earth ions in the cage-glass state of the studied dodecaborides. The data obtained allow concluding that the emergence of Yb-Yb dimers in the Tm{sub 1-x}Yb{sub x}B{sub 12} cage-glass matrix is the origin of the metal-insulator transition observed in the achetypal strongly correlated electron system of YbB{sub 12}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nucleation rate controlled grain boundary and lattice creep

Nucleation versus diffusion rate-limited bicrystal and single crystal creep exhibit different scaling dependencies that enable the mechanisms to be isolated when measured as a function of sample size. It has recently been suggested that nucleation rate-limited kinetic models generally describe the non-Newtonian portion of the creep response well, but more direct evidence is required. This work analyzes the grain boundary creep response of UO 2 , a pyrochlore high entropy oxide, silver, and palladium, along with the lattice creep of silver using small-scale in situ loading in the transmission electron microscope. At small sizes, each system exhibits scale dependence associated with nucleation rate-limited kinetics. Fits of the data produce activation volumes on the order of a few Burgers vectors cubed with positive temperature coefficients as expected for nucleation kinetics. The activation enthalpies fall in the range of about 0.4 eV to 1.7 eV, being lower for the metals and higher for the oxides.

36 MATERIALS SCIENCE↗

Yttrium aluminium garnet under pressure: Structural, elastic, and vibrational properties from ab initio studies

The structural, elastic, and vibrational properties of yttrium aluminum garnet Y{sub 3}Al{sub 5}O{sub 12} are studied under high pressure by ab initio calculations in the framework of the density functional theory. The calculated ground state properties are in good agreement with the available experimental data. Pressure dependences of bond length and bulk moduli of the constituent polyhedra are reported. The evolution of the elastic constants and the major elastic properties, Young and shear modulus, Poisson's ratios, and Zener anisotropy ratio, are described. The mechanical stability is analyzed, on the light of “Born generalized stability criteria,” showing that the garnet is mechanically unstable above 116 GPa. Symmetries, frequencies, and pressure coefficients of the Raman-active modes are discussed on the basis of the calculated total and partial phonon density of states, which reflect the dynamical contribution of each atom. The relations between the phonon modes of Y{sub 3}Al{sub 5}O{sub 12} and the internal and external molecular modes of the different polyhedra are discussed. Infrared-active modes, as well as the silent modes, and their pressure dependence are also investigated. No dynamical instabilities were found below 116 GPa.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Efficient surface plasmon amplification in gain-assisted silver nanotubes and associated dimers

SPASER (surface plasmon amplification by stimulated emission of radiation) properties in active SiO{sub 2}–Ag nanotubes and associated dimers have been investigated by using the scattering theory and the finite element method. In the active Ag nanotube, as the gain coefficient of the core increases to a critical value, a super-resonance occurs. The SPASER phenomenon also can be found in the active Ag nanotube dimer. The strong couplings between two nanotubes lead to larger gain threshold for the active Ag nanotube dimer compared with the active Ag nanotube. At the super-resonance, the maximal surface enhanced Raman scattering factor at the “hot spot” in the active Ag nanotube dimer can achieve about 8 × 10{sup 18}, which is large enough for single molecule detection. Furthermore, with increasing the separation between two Ag nanotubes, the gain threshold value for the super-resonance of the active Ag nanotube dimer decreases, while the corresponding super-resonance wavelength increases first and then decreases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optimisation of a multi-disk cryogenic amplifier for a high-intensity, high-repetition-rate laser system

Holders of the active elements of a multi-disk multipass amplifier with a liquid-free closed cryogenic cooling cycle are modified. The equilibrium temperature of the active elements is experimentally investigated in relation to the power of diode pumping for the modified crystal holders. The dependence of the gain coefficient on the temperature of the active elements is measured. A small-signal gain of up to 1.2 is obtained in a single pass through the active element. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Plasma Protein Turnover Rates in Rats Using Stable Isotope Labeling, Global Proteomics, and Activity-Based Protein Profiling

Protein turnover is important for general health on cellular and organism scales providing a strategy to replace old, damaged, or dysfunctional proteins. Protein turnover also informs of biomarker kinetics, as a better understanding of synthesis and degradation of proteins increases the clinical utility of biomarkers. Here, turnover rates of plasma proteins in rats were measured in vivo using a pulse-chase stable isotope labeling experiment. During the pulse, rats (n=5) were fed 13C6-labeled lysine (“heavy”) feed for 23 days to label proteins. During the chase, feed was changed to an unlabeled equivalent feed (“light”), and blood was repeatedly sampled from rats over 10 time points for 28 days. Plasma samples were digested with trypsin, and analyzed with liquid chromatography-tandem mass spectrometry (LC-MS/MS). MaxQuant was used to identify peptides and proteins, and quantify heavy:light lysine ratios. A system of ordinary differential equations was used to calculate protein turnover rates. Using this approach, 273 proteins were identified, and turnover rates were quantified for 157 plasma proteins with half-lives ranging 0.3-103 days. For the ~70 most abundant proteins, variability in turnover rates among rats was low (median coefficient of variation: 0.09). Activity-based protein profiling was applied to pooled plasma samples to enrich serine hydrolases using a fluorophosphonate (FP2) activity-based probe. This enrichment resulted in turnover rates for an additional 17 proteins. This study is the first to measure global plasma protein turnover rates in rats in vivo, measure variability of protein turnover rates in any animal model, and utilize activity-based protein profiling for enhancing measurements of targeted, low-abundant proteins, such as those commonly used as biomarkers. Measured protein turnover rates will be important for understanding of the role of protein turnover in cellular and organism health as well as increasing the utility of protein biomarkers through better understanding of processes governing biomarker kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lithium ion diffusion in Li β-alumina single crystals measured by pulsed field gradient NMR spectroscopy

The lithium ion diffusion coefficient of a 93% Li β-alumina single crystal was measured for the first time using pulsed field gradient (PFG) NMR spectroscopy with two different crystal orientations. The diffusion coefficient was found to be 1.2 × 10{sup −11} m{sup 2}/s in the direction perpendicular to the c axis at room temperature. The Li ion diffusion coefficient along the c axis direction was found to be very small (6.4 × 10{sup −13} m{sup 2}/s at 333 K), which suggests that the macroscopic diffusion of the Li ion in the β-alumina crystal is mainly two-dimensional. The diffusion coefficient for the same sample was also estimated using NMR line narrowing data and impedance measurements. The impedance data show reasonable agreement with PFG-NMR data, while the line narrowing measurements provided a lower value for the diffusion coefficient. Line narrowing measurements also provided a relatively low value for the activation energy and pre-exponential factor. The temperature dependent diffusion coefficient was obtained in the temperature range 297–333 K by PFG-NMR, from which the activation energy for diffusion of the Li ion was estimated. The activation energy obtained by PFG-NMR was smaller than that obtained by impedance measurements, which suggests that thermally activated defect formation energy exists for 93% Li β-alumina single crystals. The diffusion time dependence of the diffusion coefficient was observed for the Li ion in the 93% Li β-alumina single crystal by means of PFG-NMR experiments. Motion of Li ion in fractal dimension might be a possible explanation for the observed diffusion time dependence of the diffusion coefficient in the 93% Li β–alumina system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Whole-remnant and maximum-voxel SPECT/CT dosimetry in {sup 131}I-NaI treatments of differentiated thyroid cancer

Purpose: To investigate the possible differences between SPECT/CT based whole-remnant and maximum-voxel dosimetry in patients receiving radio-iodine ablation treatment of differentiated thyroid cancer (DTC). Methods: Eighteen DTC patients were administered 1.11 GBq of {sup 131}I-NaI after near-total thyroidectomy and rhTSH stimulation. Two patients had two remnants, so in total dosimetry was performed for 20 sites. Three SPECT/CT scans were performed for each patient at 1, 2, and 3–7 days after administration. The activity, the remnant mass, and the maximum-voxel activity were determined from these images and from a recovery-coefficient curve derived from experimental phantom measurements. The cumulated activity was estimated using trapezoidal-exponential integration. Finally, the absorbed dose was calculated using S-values for unit-density spheres in whole-remnant dosimetry and S-values for voxels in maximum-voxel dosimetry. Results: The mean absorbed dose obtained from whole-remnant dosimetry was 40 Gy (range 2–176 Gy) and from maximum-voxel dosimetry 34 Gy (range 2–145 Gy). For any given patient, the activity concentrations for each of the three time-points were approximately the same for the two methods. The effective half-lives varied (R = 0.865), mainly due to discrepancies in estimation of the longer effective half-lives. On average, absorbed doses obtained from whole-remnant dosimetry were 1.2 ± 0.2 (1 SD) higher than for maximum-voxel dosimetry, mainly due to differences in the S-values. The method-related differences were however small in comparison to the wide range of absorbed doses obtained in patients. Conclusions: Simple and consistent procedures for SPECT/CT based whole-volume and maximum-voxel dosimetry have been described, both based on experimentally determined recovery coefficients. Generally the results from the two approaches are consistent, although there is a small, systematic difference in the absorbed dose due to differences in the S-values, and some variability due to differences in the estimated effective half-lives, especially when the effective half-life is long. Irrespective of the method used, the patient absorbed doses obtained span over two orders of magnitude.

60 APPLIED LIFE SCIENCES↗

The initial dissolution rates of simulated UK Magnox–ThORP blend nuclear waste glass as a function of pH, temperature and waste loading

The first comprehensive assessment of the dissolution kinetics of simulant Magnox–THORP blended UK high-level waste glass, obtained by performing a range of single-pass flow-through experiments, is reported here. Inherent forward rates of glass dissolution were determined over a temperature range of 23 to 70°C and an alkaline pH range of 8.0 to 12.0. Linear regression techniques were applied to the TST kinetic rate law to obtain fundamental parameters necessary to model the dissolution kinetics of UK high-level waste glass (the activation energy (Ea), pH power law coefficient (η) and the intrinsic rate constant (k0)), which is of importance to the post-closure safety case for the geological disposal of vitreous products. The activation energies based on B release ranged from 55 ± 3 to 83 ± 9 kJ mol–1, indicating that Magnox–THORP blend glass dissolution has a surface-controlled mechanism, similar to that of other high- level waste simulant glass compositions such as the French SON68 and LAW in the US. Forward dissolution rates, based on Si, B and Na release, suggested that the dissolution mechanism under dilute conditions, and pH and temperature ranges of this study, was not sensitive to composition as defined by HLW-incorporation rate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tritium diffusion and formation in the bulk and defective surface of γ-LiAlO2 pellets: First-principles investigation

In tritium-producing burnable absorber rods (TPBAR), γ-LiAlO2 is used in the form of an annular ceramic pellet enriched with the 6Li isotope. When irradiated in a pressurized water reactor (PWR), the <sup>6</sup>Li pellets absorb neutrons and produce tritium (<sup>3</sup>H) through <sup>6</sup>Li + n <sup>3</sup>H + α. The 3H chemically reacts with the metal getter where it is captured and leads to formation of a metal hydride. For TPBARs to enable effective tritium production in PWRs, we investigated the <sup>3</sup>H diffusion pathways in the bulk and surface of γ-LiAlO<sub>2</sub> with different concentrations of lithium defects. The calculated results for bulk and low-index surfaces, thermal conductivity, 3H activation energy barriers, and the 3H diffusion coefficients in γ-LiAlO<sub>2</sub> are in good agreement with the available experimental values. In the bulk, our results show that the smallest activation energy barrier is 0.63 eV for substitutional <sup>3</sup>H diffusion with a diffusion coefficient of 3.25x10<sup>-12</sup> m<sup>2</sup>/s. After <sup>3</sup>H diffused from bulk to the surface, it could form different species (such as <sup>3</sup>H<sub>2</sub>, <sup>3</sup>H<sub>2</sub>O, C<sup>3</sup>H<sub>4</sub>) depending on the surface structure, vacancy types and the impurity carbon. Our results indicate that the <sup>3</sup>H<sub>2</sub> is the main product from γ-LiAlO<sub>2</sub> pellets. As the number of V<sub>Li</sub> vacancies and <sup>3</sup>H atoms increases under irradiation (<sup>3</sup>H-rich condition), <sup>3</sup>H<sub>2</sub>O release could increase from the surface of γ-LiAlO<sub>2</sub> pellets.

Jia, Ting↗

Inner Belt Electron Decay Timescales: A Comparison of Van Allen Probes and DREAM3D Losses Following the June 2015 Storm

Abstract NASA's Van Allen Probes observed significant, long‐lived fluxes of inner belt electrons up to ∼1 MeV after geomagnetic storms in March and June 2015. Reanalysis of Magnetic Electron Ion Spectrometer (MagEIS) data with improved background correction showed a clearer picture of the relativistic electron population that persisted through 2016 and into 2017 above the Fennell et al. (2015, https://doi.org/10.1002/2014gl062874 ) limit. The intensity and duration of these enhancements allow estimation of decay timescales for comparison with simulated decay rates and theoretical lifetimes. We compare decay timescales from these data and DREAM3D simulations based on them using geomagnetic activity‐dependent pitch angle diffusion coefficients derived from plasmapause‐indexed wave data (Malaspina et al., 2016, https://doi.org/10.1002/2016gl069982 , 2018, https://doi.org/10.1029/2018gl078564 ) and phase space densities derived from MagEIS observations. Simulated decay rates match observed decay rates more closely than the theoretical lifetime due to significantly nonequilibrium pitch angle distributions in simulation and data. We conclude that nonequilibrium effects, rather than a missing diffusion or loss process, account for observed short decay rates.

79 ASTRONOMY AND ASTROPHYSICS↗

Alloying effects on superionic conductivity in lithium indium halides for all-solid-state batteries

Alloying of anions is a promising engineering strategy for tuning ionic conductivity in halide-based inorganic solid electrolytes. We explain the alloying effects in Li 3 InBr 6-x Cl x , in terms of strain, chemistry, and microstructure, using first-principles molecular dynamics simulations and novel electronic structure analysis. We find that strain and bond chemistry can be tuned through alloying and affect the activation energy and maximum diffusivity coefficient. The similar conductivities of the x=3 and x=6 compositions can be understood by assuming the alloy separates into Brrich and Cl-rich regions. Phase-separation increases diffusivity at the interface and in the expanded Cl-region, suggesting microstructure effects are critical.

25 ENERGY STORAGE↗

First-principles multiple-barrier diffusion theory. The case study of interstitial diffusion in CdTe

The diffusion of particles in solid-state materials generally involves several sequential thermal-activation processes. However, presently, diffusion coefficient theory only deals with a single barrier, i.e., it lacks an accurate description to deal with multiple-barrier diffusion. Here, we develop a general diffusion coefficient theory for multiple-barrier diffusion. Using our diffusion theory and first-principles calculated hopping rates for each barrier, we calculate the diffusion coefficients of Cd, Cu, Te, and Cl interstitials in CdTe for their full multiple-barrier diffusion pathways. As a result, we found that the calculated diffusivity agrees well with the experimental measurement, thus justifying our theory, which is general for many other systems.

36 MATERIALS SCIENCE↗

Evaluation of Fe-βGa 2 O 3 for Photoconductive Semiconductor Switching

We present iron-doped beta gallium oxide (Fe- β Ga2O3) as a candidate for photoconductive semiconductor switches (PCSSs) with sub-bandgap light. From a commercially available Fe- β Ga2O3 wafer, we first did material characterization. This included measurements of absorption coefficient and dopant composition, carrier activation energy up to 200 °C, break down field of planar electrodes (limited from material passivation), and free carrier recombination lifetime, and thermal effects up to 203 °C on photocurrent with a 447 nm light emitting diode (LED) source. Here, we then demonstrated pulsed operation of a Fe- β Ga2O3 PCSS under different sub-bandgap wavelengths (355, 532, and 1064 nm) and sub-ns pulses. Fe- β Ga2O3 is a candidate for high temperature PCSS with 355 nm responsivity of 7×10 -7 A-cm/W-kV at room temperature and up to 5.5×10 -4 A-cm/W-kV at 200 °C. From these investigations, we discuss a simple trap model to describe the illumination process of the PCSS. Fe- β Ga2O3 has a high breakdown field and has moderate responsivity characteristics, but the dark current at high temperature leads to low photo-to-dark current ratio (PDCR). Regardless, we verify its potential as a PCSS material for harsh environment applications.

42 ENGINEERING↗

Galvanostatic Intermittent Titration Technique Reinvented: Part II. Experiments

Following a critical review of the galvanostatic intermittent titration technique in Part I, here we experimentally demonstrate how to extract chemical diffusivity with a modified method. We prepare dense bulk samples that ensure diffusion-limitation. We utilize the scaling with $\sqrt{{t}_{\mathrm{relax}}+\tau }-\sqrt{{t}_{\mathrm{relax}}}$ (trelax: relaxation time; τ: pulse duration), avoiding problems with composition-dependent overpotentials. The equilibrium Nernst voltage is measured separately using small porous particles. This separation between the diffusion measurement and the titration procedure is critical for performing each measurement in a reliable setting. We report the chemical diffusion coefficients of LixNi1/3Mn1/3Co1/3O2 and their activation energy. We extract ionic conductivity and compare it with total conductivity to confirm ion-limitation in chemical diffusion. The measurements suggest that the time scale for diffusion in typical Li-ion battery particles could be much shorter than that of the intercalation/deintercalation processes at the particle surface (Biot number less than 0.1).

25 ENERGY STORAGE↗