Results for “Aircraft Wing Components” — Page 15

NASA NTRS1986

Propeller-induced structure-borne noise - Laboratory-based test apparatus

A potentially important source of structure-borne interior noise transmission in advanced turboprop aircraft is the impingement of the propeller wake/vortex on downstream aerodynamic surfaces. The expected levels of propeller wake/vortex-induced structure-borne noise transmission are not known nor can they be determined with present-day technology. A test apparatus has been designed, built and calibrated for the purposes of studying propeller-induced, structure-borne noise transmission in prototypical aircraft structures. The principal approach to the test apparatus design was to provide a physical means of separating the airborne and structure-borne noise components so that the structure-borne noise transmission response could be studied directly without airborne noise contamination. This was accomplished by housing the receiving fuselage structure in an acoustic shield fitted with a wing-to-fuselage acoustic seal. Initial evaluation of the wing-to-fuselage acoustic seal indicates adequate airborne noise isolation to allow direct study of structure-borne noise transmission.

Unruh, J. F.↗

NASA NTRS2018

Far Term Noise Reduction Roadmap for the Mid-Fuselage Nacelle Subsonic Transport

A noise reduction technology roadmap study is presented to determine the feasibility for the Mid-Fuselage Nacelle (MFN) aircraft concept to achieve the noise goal set by NASA for the Far Term time frame, beyond 2035. The study starts with updating the noise prediction of the existing MFN configuration that had been modeled for the time frame between 2025 and 2035. The updated prediction for the Mid Term time frame is 34.3 dB cumulative effective perceived noise level (EPNL) below the Stage 4 regulation. A suite of technologies that are deemed feasible to mature for practical implementation in the Far Term and whose potentials for noise reduction have been illustrated is selected for analysis. For each technology, component noise reduction is modeled either by available experimental data or by physics-based modeling with aircraft system level methods. The noise reduction is then applied to the corresponding noise component predicted by advanced aircraft system noise prediction tools, and the total aircraft noise is predicted as the incoherent summation of the components. It is shown that the Far Term MFN aircraft has the potential to achieve a cumulative noise level of 40.2 EPNL dB below Stage 4. The key technologies to achieve this low aircraft noise level are assessed by the impact of each technology on the aircraft system noise. This roadmap shows the potential of this revolutionary, yet still tube-and-wing, MFN concept to reach the NASA Far Term noise goal.

Guo, Yueping↗

NASA NTRS1980

Small Transport Aircraft Technology

The article surveys the results of the NASA-instituted Small Transport Aircraft Technology (STAT) research effort aimed at generating advanced technologies for application to new small, short haul transports having significantly better performance, efficiency, and environmental compatibility. Discussion covers fuselage designs and bonded aluminum-honeycomb wing construction which reduces the number of parts and fasteners, and gives a smoother outer contour. Topics discussed include: advanced aluminum alloys, composite primary structures, propellers, engine components, icing protection, avionics, flight controls, aerodynamics, and gust load alleviation.

Galloway, T. L.↗

NASA NTRS2000

Gust Alleviation Using Direct Gust Measurement

The increasing competition in the market of civil aircraft leads to operating efficiency and passenger comfort being very important sales arguments. Continuous developments in jet propulsion technology helped to reduce energy consumption, as well as noise and vibrations due to the engines. The main problem with respect to ride comfort is, however, the transmittance of accelerations and jerkiness imposed by atmospheric turbulence from the wings to the fuselage. This 'gust' is also a design constraint: Light airplane structures help to save, energy, but are more critical to resist the loads imposed by turbulence. For both reasons, efficient gust alleviation is necessary to improve the performance of modern aircraft. Gust can be seen as a change in the angle of attack or as an additional varying vertical component of the headwind. The effect of gust can be very strong, since the same aerodynamic forces that keep the airplane flying are involved. Event though the frequency range of those changes is quite low, it is impossible for the pilot to alleviate gust manually. Besides, most of the time during the flight, the, autopilot maintains course and the attitude of flight. Certainly, most autopilots should be capable of damping the roughest parts of turbulence, but they are unable to provide satisfactory results in that field. A promising extension should be the application of subsidiary, control, where the inner (faster) control loop alleviates turbulence and the outer (slower) loop controls the attitude of flight. Besides the mentioned ride comfort, another reason for gust alleviation with respect to the fuselage is the sensibility of electrical devices to vibration and high values of acceleration. Many modern airplane designs--especially inherently instable military aircraft--are highly dependent on avionics. The lifetime and the reliability of these systems is thus essential.

Hoppe, Sven Marco↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRS1989

Aircraft propeller induced structure-borne noise

A laboratory-based test apparatus employing components typical of aircraft construction was developed that would allow the study of structure-borne noise transmission due to propeller induced wake/vortex excitation of in-wake structural appendages. The test apparatus was employed to evaluate several aircraft installation effects (power plant placement, engine/nacelle mass loading, and wing/fuselage attachment methods) and several structural response modifications for structure-borne noise control (the use of wing blocking mass/fuel, wing damping treaments, and tuned mechanical dampers). Most important was the development of in-flight structure-borne noise transmission detection techniques using a combination of ground-based frequency response function testing and in-flight structural response measurement. Propeller wake/vortex excitation simulation techniques for improved ground-based testing were also developed to support the in-flight structure-borne noise transmission detection development.

Unruh, James F.↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

CFD↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

Natural Laminar Flow↗

NASA NTRS1997

Development of a Closed-Loop Strap Down Attitude System for an Ultrahigh Altitude Flight Experiment

A low-cost attitude system has been developed for an ultrahigh altitude flight experiment. The experiment uses a remotely piloted sailplane, with the wings modified for flight at altitudes greater than 100,000 ft. Mission requirements deem it necessary to measure the aircraft pitch and bank angles with accuracy better than 1.0 deg and heading with accuracy better than 5.0 deg. Vehicle cost restrictions and gross weight limits make installing a commercial inertial navigation system unfeasible. Instead, a low-cost attitude system was developed using strap down components. Monte Carlo analyses verified that two vector measurements, magnetic field and velocity, are required to completely stabilize the error equations. In the estimating algorithm, body-axis observations of the airspeed vector and the magnetic field are compared against the inertial velocity vector and a magnetic-field reference model. Residuals are fed back to stabilize integration of rate gyros. The effectiveness of the estimating algorithm was demonstrated using data from the NASA Dryden Flight Research Center Systems Research Aircraft (SRA) flight tests. The algorithm was applied with good results to a maximum 10' pitch and bank angles. Effects of wind shears were evaluated and, for most cases, can be safely ignored.

Whitmore, Stephen A.↗

NASA NTRS2014

Propulsion Electric Grid Simulator (PEGS) for Future Turboelectric Distributed Propulsion Aircraft

NASA Glenn Research Center, in collaboration with the aerospace industry and academia, has begun the development of technology for a future hybrid-wing body electric airplane with a turboelectric distributed propulsion (TeDP) system. It is essential to design a subscale system to emulate the TeDP power grid, which would enable rapid analysis and demonstration of the proof-of-concept of the TeDP electrical system. This paper describes how small electrical machines with their controllers can emulate all the components in a TeDP power train. The whole system model in Matlab/Simulink was first developed and tested in simulation, and the simulation results showed that system dynamic characteristics could be implemented by using the closed-loop control of the electric motor drive systems. Then we designed a subscale experimental system to emulate the entire power system from the turbine engine to the propulsive fans. Firstly, we built a system to emulate a gas turbine engine driving a generator, consisting of two permanent magnet (PM) motors with brushless motor drives, coupled by a shaft. We programmed the first motor and its drive to mimic the speed-torque characteristic of the gas turbine engine, while the second motor and drive act as a generator and produce a torque load on the first motor. Secondly, we built another system of two PM motors and drives to emulate a motor driving a propulsive fan. We programmed the first motor and drive to emulate a wound-rotor synchronous motor. The propulsive fan was emulated by implementing fan maps and flight conditions into the fourth motor and drive, which produce a torque load on the driving motor. The stator of each PM motor is designed to travel axially to change the coupling between rotor and stator. This feature allows the PM motor to more closely emulate a wound-rotor synchronous machine. These techniques can convert the plain motor system into a unique TeDP power grid emulator that enables real-time simulation performance using hardware-in-the-loop (HIL).

electric power grid emulator↗

NASA NTRS2015

Subsonic Ultra Green Aircraft Research: Phase 2: Hybrid Electric Design Exploration - Volume 2

This report summarizes the hybrid electric concept design, analysis, and modeling work accomplished by the Boeing Subsonic Ultra Green Aircraft Research (SUGAR) team, consisting of Boeing Research and Technology, Boeing Commercial Airplanes, General Electric, and Georgia Tech.Performance and sizing tasks were conducted for hybrid electric versions of a conventional tube-and-wing aircraft and a hybrid wing body. The high wing Truss Braced Wing (TBW) SUGAR Volt was updated based on results from the TBW work (documented separately) and new engine performance models. Energy cost and acoustic analyses were conducted and technology roadmaps were updated for hybrid electric and battery technology. NOx emissions were calculated for landing and takeoff (LTO) and cruise. NPSS models were developed for hybrid electric components and tested using an integrated analysis of superconducting and non-superconducting hybrid electric engines. The hybrid electric SUGAR Volt was shown to produce significant emissions and fuel burn reductions beyond those achieved by the conventionally powered SUGAR High and was able to meet the NASA goals for fuel burn. Total energy utilization was not decreased but reduced energy cost can be achieved for some scenarios. The team was not able to identify a technology development path to meet NASA's noise goals

Bradley, Marty K.↗

NASA NTRS2012

Acoustic Shielding for a Model Scale Counter-rotation Open Rotor

The noise shielding benefit of installing an open rotor above a simplified wing or tail is explored experimentally. The test results provide both a benchmark data set for validating shielding prediction tools and an opportunity for a system level evaluation of the noise reduction potential of propulsion noise shielding by an airframe component. A short barrier near the open rotor was found to provide up to 8.5 dB of attenuation at some directivity angles, with tonal sound particularly well shielded. Predictions from two simple shielding theories were found to overestimate the shielding benefit.

Acoustics shielding↗

NASA NTRS1976

Applications of vortex lattice theory to preliminary aerodynamic design

Some applications of the vortex-lattice theory to the preliminary aerodynamic design and analysis of subsonic aircraft were presented. These methods include the Rockwell-Tulinius vortex-lattice theory for estimating aerodynamic characteristics, a Trefftz plane optimization procedure for determining the span loads for minimum induced drag, and a modification of the Trefftz plane procedure to estimate the induced drag for specified span loads. The first two methods are used to aerodynamically design aircraft planforms, twists, and cambers, and the latter method is used to estimate the drag for components such as flaps and control surfaces. Results from the theories for predicting lift and pitching moment, drag due to lift, and the drag of control surfaces are compared with experimental data. This data was obtained on a general aviation model with flaps and a close-coupled canard-wing model.

Paulson, J. W., Jr.↗

NASA NTRS1992

Intercomparison results for FIFE flux aircraft

Three atmospheric research aircraft were used to explore the atmospheric boundary layer during FIFE: the National Research Council of Canada Twin Otter, the National Center for Atmospheric Research (NCAR) King Air, and the University of Wyoming King Air. The aircraft were used to measure the mean and turbulent structure of the boundary layer and its variation with height, time, and space. These measurements are important to FIFE because they are being used to scale up point surface observations to landscape scales and because they can be used to relate satellite radiance measurements to boundary layer processes. Because the aircraft were used in coordinated flight patterns to investigate changes within and between intensive field campaigns, wing-to-wing intercomparisons were made so that measurements from one aircraft could be related to another. Intercomparisons were flown on 4 days in 1987 and 3 days in 1989. The eddy correlation measurements of the mixed layer fluxes of moisture and sensible heat were of particular interest to FIFE. Sensible heat fluxes agreed within 15 W/sq m and moisture fluxes agreed within 21 W/sq m. Mean wind component differences were within 1.0 m/s, air temperature within 0.3 C, and mixing ratio within 2 g/kg. Standard deviations showed similar good agreement, with mean differences generally less than 0.1 m/s for the wind components and 0.03 C for potential temperature. Intercomparisons between the NCAR King Air and the Twin Otter showed better agreement in 1989 than in 1987. Overall, the results suggest that data from the FIFE boundary layer aircraft will need little correction to account for instrument biases and spurious fluctuations.

Macpherson, J. I.↗

NASA NTRS1978

Service experience of composite parts on the L-1011 and C-130

Composite flight service programs are in progress on two aircraft, the L-1011 and C-130. A set of Kevlar-49/epoxy fairings is being flight tested on three L-1011's and have had no major service problems after 10,000 hours of service. The center wing box aluminum skins and hat stiffeners were reinforced with precured bonded boron/epoxy strips on three C-130's. After almost three years and over 4000 flight hours, these components are continuing to perform satisfactorily in service. Another flight service component on the L-1011 is a graphite/epoxy floor post, which is free of service problems or defects after 10,000 flight hours. These components provide significant verification of the serviceability of all three major composite reinforcement types.

Stone, R. H.↗

NASA NTRS1978

Evaluation of laminar flow control system concepts for subsonic commercial transport aircraft

A two-year study conducted to establish a basis for industry decisions on the application of laminar flow control (LFC) to future commercial transports was presented. Areas of investigation included: (1) mission definition and baseline selection; (2) concepts evaluations; and (3) LFC transport configuration selection and component design. The development and evaluation of competing design concepts was conducted in the areas of aerodynamics, structures and materials, and systems. The results of supporting wind tunnel and laboratory testing on a full-scale LFC wing panel, suction surface opening concepts and structural samples were included. A final LFC transport was configured in incorporating the results of concept evaluation studies and potential performance improvements were assessed. Remaining problems together with recommendations for future research are discussed.

Source record↗

NASA NTRS1993

Application of artificial neural networks to the design optimization of aerospace structural components

The application of artificial neural networks to capture structural design expertise is demonstrated. The principal advantage of a trained neural network is that it requires trivial computational effort to produce an acceptable new design. For the class of problems addressed, the development of a conventional expert system would be extremely difficult. In the present effort, a structural optimization code with multiple nonlinear programming algorithms and an artificial neural network code NETS were used. A set of optimum designs for a ring and two aircraft wings for static and dynamic constraints were generated by using the optimization codes. The optimum design data were processed to obtain input and output pairs, which were used to develop a trained artificial neural network with the code NETS. Optimum designs for new design conditions were predicted by using the trained network. Neural net prediction of optimum designs was found to be satisfactory for most of the output design parameters. However, results from the present study indicate that caution must be exercised to ensure that all design variables are within selected error bounds.

Berke, Laszlo↗