SEARCH · Search NASA

Results for “Airframe Noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Characterization of Urban Air Mobility Vehicle Operational Noise and Community Noise Impact

This presentation focuses on the process for predicting urban air mobility (UAM) vehicle noise at the source and how that can be used to estimate the impact on the community. Following conceptual design, in which the vehicle is appropriately sized for its intended mission, a comprehensive analysis must be performed for a range of operating conditions spanning the flight envelope to determine the corresponding configurations of the vehicle, that is, the trimmed states. Many UAM vehicles have redundant controls, so the trimmed state for any particular operating condition may not be unique, with some states producing more noise than others. For each trimmed state, the noise produced by each source, for example, steady and unsteady rotor noise, inclusive of propulsion airframe aeroacoustic effects, may be computed and so-called source noise (hemi)spheres generated. Land use planning tools, including those using simulation and integrated modeling approaches, use these (or derived) data to generate noise exposure maps on the ground. Alternatively, these data may serve as input to auralization, turning the numerical data into an audible sound that can subsequently be used as part of a perception-influenced acoustic design process that takes into account human response.

urban air mobiliy↗

NASA NTRSDate not supplied

Characterization of Urban Air Mobility Vehicle Operational Noise and Community Noise Impact

This presentation focuses on the process for predicting urban air mobility (UAM) vehicle noise at the source and how that can be used to estimate and mitigate the impact on the community. Following conceptual design, in which the vehicle is appropriately sized for its intended mission, a comprehensive analysis must be performed for a range of operating conditions spanning the flight envelope to determine the corresponding configurations of the vehicle, that is, the trimmed states. Many UAM vehicles have redundant controls, so the trimmed state for any particular operating condition may not be unique, with some states producing more noise than others. For each trimmed state, the noise produced by each source, for example, steady and unsteady rotor noise, inclusive of propulsion airframe aeroacoustic effects, may be computed and so-called source noise (hemi)spheres generated. The data may be used for analyses supporting noise certification or serve as input to auralizations (turning the numerical data into an audible sound) that can subsequently be used as part of a perception-influenced acoustic design process. Land use planning tools, including those using simulation and integrated modeling approaches, also use these (or derived) data to generate noise exposure maps on the ground. Finally, the data may be used to support development of low noise flight operations using an acoustic flight simulator or acoustically aware flight control.

urban air mobility↗

NASA NTRS2014

Jet-Surface Interaction Test: Flow Measurements Results

Modern aircraft design often puts the engine exhaust in close proximity to the airframe surfaces. Aircraft noise prediction tools must continue to develop in order to meet the challenges these aircraft present. The Jet-Surface Interaction Tests have been conducted to provide a comprehensive quality set of experimental data suitable for development and validation of these exhaust noise prediction methods. Flow measurements have been acquired using streamwise and cross-stream particle image velocimetry (PIV) and fluctuating surface pressure data acquired using flush mounted pressure transducers near the surface trailing edge. These data combined with previously reported far-field and phased array noise measurements represent the first step toward the experimental data base. These flow data are particularly applicable to development of noise prediction methods which rely on computational fluid dynamics to uncover the flow physics. A representative sample of the large flow data set acquired is presented here to show how a surface near a jet affects the turbulent kinetic energy in the plume, the spatial relationship between the jet plume and surface needed to generate surface trailing-edge noise, and differences between heated and unheated jet flows with respect to surfaces.

Flow↗

NASA NTRS1994

On-line, adaptive state estimator for active noise control

Dynamic characteristics of airframe structures are expected to vary as aircraft flight conditions change. Accurate knowledge of the changing dynamic characteristics is crucial to enhancing the performance of the active noise control system using feedback control. This research investigates the development of an adaptive, on-line state estimator using a neural network concept to conduct active noise control. In this research, an algorithm has been developed that can be used to estimate displacement and velocity responses at any locations on the structure from a limited number of acceleration measurements and input force information. The algorithm employs band-pass filters to extract from the measurement signal the frequency contents corresponding to a desired mode. The filtered signal is then used to train a neural network which consists of a linear neuron with three weights. The structure of the neural network is designed as simple as possible to increase the sampling frequency as much as possible. The weights obtained through neural network training are then used to construct the transfer function of a mode in z-domain and to identify modal properties of each mode. By using the identified transfer function and interpolating the mode shape obtained at sensor locations, the displacement and velocity responses are estimated with reasonable accuracy at any locations on the structure. The accuracy of the response estimates depends on the number of modes incorporated in the estimates and the number of sensors employed to conduct mode shape interpolation. Computer simulation demonstrates that the algorithm is capable of adapting to the varying dynamic characteristics of structural properties. Experimental implementation of the algorithm on a DSP (digital signal processing) board for a plate structure is underway. The algorithm is expected to reach the sampling frequency range of about 10 kHz to 20 kHz which needs to be maintained for a typical active noise control application.

Lim, Tae W.↗

NASA NTRS2000

NASA's Subsonic Jet Transport Noise Reduction Research

Although new jet transport airplanes in today s fleet are considerably quieter than the first jet transports introduced about 40 years ago, airport community noise continues to be an important environmental issue. NASA s Advanced Subsonic Transport (AST) Noise Reduction program was begun in 1994 as a seven-year effort to develop technology to reduce jet transport noise 10 dB relative to 1992 technology. This program provides for reductions in engine source noise, improvements in nacelle acoustic treatments, reductions in the noise generated by the airframe, and improvements in the way airplanes are operated in the airport environs. These noise reduction efforts will terminate at the end of 2001 and it appears that the objective will be met. However, because of an anticipated 3-8% growth in passenger and cargo operations well into the 21st Century and the slow introduction of new the noise reduction technology into the fleet, world aircraft noise impact will remain essentially constant until about 2020 to 2030 and thereafter begin to rise. Therefore NASA has begun planning with the Federal Aviation Administration, industry, universities and environmental interest groups in the USA for a new noise reduction initiative to provide technology for significant further reductions.

Powell, Clemans A.↗

NASA NTRS2001

Air Traffic Control Decision Support Tools for Noise Mitigation

NASA has initiated a new five year program this year, the Quiet Aircraft Technology (QAT) Program, a program which will investigate airframe and engine system noise reduction. QAT will also address community noise impact. As part of this community noise impact component, NASA will investigate air traffic management (ATM) challenges in reducing noise. In particular, controller advisory automation aids will be developed to aid the air traffic controller in addressing noise concerns as he/she manages traffic in busy terminal areas. NASA has developed controller automation tools to address capacity concerns and the QAT strategy for ATM Low Noise Operations is to build upon this tool set to create added advisories for noise mitigation. The tools developed for capacity will be briefly reviewed, followed by the QAT plans to address ATM noise concerns. A major NASA goal in global civil aviation is to triple the aviation system throughput in all-weather conditions while maintaining safety. A centerpiece of this activity is the Center/TRACON Automation System (CTAS), an evolving suite of air traffic controller decision support tools (DSTs) to enhance capacity of arrivals and departures in both the enroute center and the TRACON. Two of these DSTs, the Traffic Management Advisor (TMA) and the passive Final approach Spacing Tool (pFAST), are in daily use at the Fort Worth Center and the Dallas/Fort Worth (DFW) TRACON, respectively, where capacity gains of 5-13% have been reported in recent NASA evaluations. Under the Federal Aviation Administration's (FAA) Free Flight Phase One Program, TMA and pFAST are each being implemented at six to eight additional sites. In addition, other DSTs are being developed by NASA under the umbrella of CTAS. This means that new software will be built upon CTAS, and the paradigm of real-time simulation evaluation followed by field site development and evaluation will be the pathway for the new tools. Additional information is included in the original extended abstract.

Tobias, Leonard↗

NASA NTRS2004

Investigation of Acoustical Shielding by a Wedge-Shaped Airframe

Experiments on a scale model of an advanced unconventional subsonic transport concept, the Blended Wing Body (BWB), have demonstrated significant shielding of inlet-radiated noise. A computational model of the shielding mechanism has been developed using a combination of boundary integral equation method (BIEM) and equivalent source method (ESM). The computation models the incident sound from a point source in a nacelle and determines the scattered sound field. In this way the sound fields with and without the airfoil can be estimated for comparison to experiment. An experimental test bed using a simplified wedge-shape airfoil and a broadband point noise source in a simulated nacelle has been developed for the purposes of verifying the analytical model and also to study the effect of engine nacelle placement on shielding. The experimental study is conducted in the Anechoic Noise Research Facility at NASA Langley Research Center. The analytic and experimental results are compared at 6300 and 8000 Hz. These frequencies correspond to approximately 150 Hz on the full scale aircraft. Comparison between the experimental and analytic results is quite good, not only for the noise scattering by the airframe, but also for the total sound pressure in the far field. Many of the details of the sound field that the analytic model predicts are seen or indicated in the experiment, within the spatial resolution limitations of the experiment. Changing nacelle location produces comparable changes in noise shielding contours evaluated analytically and experimentally. Future work in the project will be enhancement of the analytic model to extend the analysis to higher frequencies corresponding to the blade passage frequency of the high bypass ratio ducted fan engines that are expected to power the BWB.

Gerhold, Carl H.↗

NASA NTRS2006

Investigation of Acoustical Shielding by a Wedge-Shaped Airframe

Gerhold, Carl H.↗

NASA NTRS2014

Shielding of Turbomachinery Broadband Noise from a Hybrid Wing Body Aircraft Configuration

The results of an experimental study on the effects of engine placement and vertical tail configuration on shielding of exhaust broadband noise radiation are presented. This study is part of the high fidelity aeroacoustic test of a 5.8% scale Hybrid Wing Body (HWB) aircraft configuration performed in the 14- by 22-Foot Subsonic Tunnel at NASA Langley Research Center. Broadband Engine Noise Simulators (BENS) were used to determine insertion loss due to shielding by the HWB airframe of the broadband component of turbomachinery noise for different airframe configurations and flight conditions. Acoustics data were obtained from flyover and sideline microphones traversed to predefined streamwise stations. Noise measurements performed for different engine locations clearly show the noise benefit associated with positioning the engine nacelles further upstream on the HWB centerbody. Positioning the engine exhaust 2.5 nozzle diameters upstream (compared to 0.5 nozzle diameters downstream) of the HWB trailing edge was found of particular benefit in this study. Analysis of the shielding performance obtained with and without tunnel flow show that the effectiveness of the fuselage shielding of the exhaust noise, although still significant, is greatly reduced by the presence of the free stream flow compared to static conditions. This loss of shielding is due to the turbulence in the model near-wake/boundary layer flow. A comparison of shielding obtained with alternate vertical tail configurations shows limited differences in level; nevertheless, overall trends regarding the effect of cant angle and vertical location are revealed. Finally, it is shown that the vertical tails provide a clear shielding benefit towards the sideline while causing a slight increase in noise below the aircraft.

Hutcheson, Florence V.↗

NASA NTRS2012

Acoustic Shielding for a Model Scale Counter-rotation Open Rotor

The noise shielding benefit of installing an open rotor above a simplified wing or tail is explored experimentally. The test results provide both a benchmark data set for validating shielding prediction tools and an opportunity for a system level evaluation of the noise reduction potential of propulsion noise shielding by an airframe component. A short barrier near the open rotor was found to provide up to 8.5 dB of attenuation at some directivity angles, with tonal sound particularly well shielded. Predictions from two simple shielding theories were found to overestimate the shielding benefit.

Acoustics shielding↗

NASA NTRSDate not supplied

Turbofan Aft-Radiated Broadband Acoustic Flight Effects

This paper presents the status and on-going development of a new model for the prediction of aft-radiated turbofan broadband noise. The proposed model is developed using data from two full-scale flight tests, the Boeing Quiet Technology Demonstrator 2 (QTD2) and the NASA/Boeing Propulsion Airframe Aeroacoustics and Aircraft System Noise (PAA&ASN) flight tests. The proposed model accounts for an observed coupling between directivity and fan relative tip Mach number. Additional features such as improved spectral and directivity characteristics are discussed. Significant improvements over prior methods implemented in the NASA Aircraft Noise Prediction Program are demonstrated, and predicted deltas to measured levels are reduced from +10/-20 dB to +/-3 dB or better at the most relevant frequencies. This is expected to greatly improve the ability of NASA to predict the noise of both current and future aircraft concepts.

Fan Noise↗

NASA NTRS1992

MD-80 aft cabin noise control: A case history

The interior noise technology program to improve the noise environment in the aft cabin of the MD-80 twin jet aircraft is discussed. Two potential noise control treatments were identified: vibration absorber devices for the airframe and for the engine. A series of ground and flight tests using in-service aircraft was then conducted. These tests showed that the vibration absorbers for the airframe and engine decreased aircraft noise significantly.

Lang, M. A.↗

NASA NTRS2011

High-Temperature Smart Structures for Engine Noise Reduction and Performance Enhancement

One of key NASA goals is to develop and integrate noise reduction technology to enable unrestricted air transportation service to all communities. One of the technical priorities of this activity has been to account for and reduce noise via propulsion/airframe interactions, identifying advanced concepts to be integrated with the airframe to mitigate these noise-producing mechanisms. An adaptive geometry chevron using embedded smart structures technology offers the possibility of maximizing engine performance while retaining and possibly enhancing the favorable noise characteristics of current designs. New high-temperature shape memory alloy (HTSMA) materials technology enables the devices to operate in both low-temperature (fan) and high-temperature (core) exhaust flows. Chevron-equipped engines have demonstrated reduced noise in testing and operational use. It is desirable to have the noise benefits of chevrons in takeoff/landing conditions, but have them deployed into a minimum drag position for cruise flight. The central feature of the innovation was building on rapidly maturing HTSMA technology to implement a next-generation aircraft noise mitigation system centered on adaptive chevron flow control surfaces. In general, SMA-actuated devices have the potential to enhance the demonstrated noise reduction effectiveness of chevron systems while eliminating the associated performance penalty. The use of structurally integrated smart devices will minimize the mechanical and subsystem complexity of this implementation. The central innovations of the effort entail the modification of prior chevron designs to include a small cut that relaxes structural stiffness without compromising the desired flow characteristics over the surface; the reorientation of SMA actuation devices to apply forces to deflect the chevron tip, exploiting this relaxed stiffness; and the use of high-temperature SMA (HTSMA) materials to enable operation in the demanding core chevron environment. The overall conclusion of these design studies was that the cut chevron concept is a critical enabling step in bringing the variable geometry core chevron within reach. The presence of the cut may be aerodynamically undesirable in some respects, but it is present only when the chevron is not immersed in the core jet exhaust. When deployed, the gap closes as the chevron tip enters the high-speed, high-temperature core stream. Aeroacoustic testing and flow visualization support the contention that this cut is inconsequential to chevron performance.

Quackenbush, Todd R.↗

NASA NTRS2018

Aircraft System Noise Assessment of the NASA D8 Subsonic Transport Concept

Avehicle-level noise assessment has been performed for theNASAD8 concept aircraft (ND8) in the NASA Advanced Air Transport Technology Project portfolio. The NASA research-level Aircraft NOise Prediction Program (ANOPP-Research) was used to predict the noise from each source component on the ND8 to build up a noise estimate for the full aircraft. The propulsion airframe aeroacoustic (PAA) effects of the ND8, namely boundary layer ingestion (BLI) with its influence on fan noise, and the noise shielding, reflection, and diffraction mechanisms of the unconventional airframe, were empirically modeled using experimental data. Noise reduction technologies appropriate to the 2025-2035 time frame were included in this study. Including all technologies and PAA effects, the ND8 is predicted to have a cumulative margin to the Stage 4 certification metric of only 7.4 EPNdB. Boundary layer ingestion is predicted to have a detrimental impact on cumulative noise levels on the order of 15 EPNdB. Fan noise is seen to be the primary noise source at all three certification points, even if the BLI noise impact could be entirely suppressed. The impact of engine noise shielding by the airframe is limited by a lack of aft shielding and the presence of horizontal tail reflections in the aft direction. The physical constraint on engine size by the pi-tail is seen as a potential barrier to engine noise reduction through the corresponding limitation on fan bypass ratio. Mildly reduced climb performance (compared to similar reference aircraft) does not provide any benefit through increased noise propagation distance. If the boundary layer ingestion noise penalty could be suppressed such that BLI would have no effect on noise, the cumulative margin to Stage 4 would increase to 22.4 EPNdB, still below the NASA Mid Term goal of 32-42 EPNdB.

Clark, Ian A.↗

NASA NTRS2021

Aircraft System Noise of the NASA D8 Subsonic Transport Concept

A vehicle-level noise assessment has been performed for the NASA D8 (ND8) concept aircraft in the NASA Advanced Air Transport Technology Project portfolio. The NASA research-level Aircraft Noise Prediction Program was used to predict the noise from each source component on the ND8 to build up a noise estimate for the full aircraft. The propulsion airframe aeroacoustic effects of the ND8 (namely, boundary-layer ingestion, with its influence on fan noise; and the noise shielding, reflection, and diffraction mechanisms of the unconventional airframe) were empirically modeled using experimental data. Far-term noise reduction technology concepts were modeled and added to the noise prediction to evaluate the low-noise potential of the ND8 in the far-term timeframe. Results indicate that the increase in fan noise due to boundary-layer ingestion, as well as the lack of aft shielding, prevents the aircraft from approaching NASA’s noise goals for either the midterm or far term. The aircraft achieves margins to Stage 4 of only 9.4 and 17.3 effective perceived noise in decibels (EPNdB) in the midterm and far-term configurations, respectively, compared with goals of 32–42 EPNdB in the midterm and 42-52 EPNdB in the far term.

aircraft system noise↗

NASA NTRS2014

Open Rotor Tone Shielding Methods for System Noise Assessments Using Multiple Databases

Advanced aircraft designs such as the hybrid wing body, in conjunction with open rotor engines, may allow for significant improvements in the environmental impact of aviation. System noise assessments allow for the prediction of the aircraft noise of such designs while they are still in the conceptual phase. Due to significant requirements of computational methods, these predictions still rely on experimental data to account for the interaction of the open rotor tones with the hybrid wing body airframe. Recently, multiple aircraft system noise assessments have been conducted for hybrid wing body designs with open rotor engines. These assessments utilized measured benchmark data from a Propulsion Airframe Aeroacoustic interaction effects test. The measured data demonstrated airframe shielding of open rotor tonal and broadband noise with legacy F7/A7 open rotor blades. Two methods are proposed for improving the use of these data on general open rotor designs in a system noise assessment. The first, direct difference, is a simple octave band subtraction which does not account for tone distribution within the rotor acoustic signal. The second, tone matching, is a higher-fidelity process incorporating additional physical aspects of the problem, where isolated rotor tones are matched by their directivity to determine tone-by-tone shielding. A case study is conducted with the two methods to assess how well each reproduces the measured data and identify the merits of each. Both methods perform similarly for system level results and successfully approach the experimental data for the case study. The tone matching method provides additional tools for assessing the quality of the match to the data set. Additionally, a potential path to improve the tone matching method is provided.

Bahr, Christopher J.↗

NASA NTRS2006

Computational Analysis of a Chevron Nozzle Uniquely Tailored for Propulsion Airframe Aeroacoustics

A computational flow field and predicted jet noise source analysis is presented for asymmetrical fan chevrons on a modern separate flow nozzle at take off conditions. The propulsion airframe aeroacoustic asymmetric fan nozzle is designed with an azimuthally varying chevron pattern with longer chevrons close to the pylon. A baseline round nozzle without chevrons and a reference nozzle with azimuthally uniform chevrons are also studied. The intent of the asymmetric fan chevron nozzle was to improve the noise reduction potential by creating a favorable propulsion airframe aeroacoustic interaction effect between the pylon and chevron nozzle. This favorable interaction and improved noise reduction was observed in model scale tests and flight test data and has been reported in other studies. The goal of this study was to identify the fundamental flow and noise source mechanisms. The flow simulation uses the asymptotically steady, compressible Reynolds averaged Navier-Stokes equations on a structured grid. Flow computations are performed using the parallel, multi-block, structured grid code PAB3D. Local noise sources were mapped and integrated computationally using the Jet3D code based upon the Lighthill Acoustic Analogy with anisotropic Reynolds stress modeling. In this study, trends of noise reduction were correctly predicted. Jet3D was also utilized to produce noise source maps that were then correlated to local flow features. The flow studies show that asymmetry of the longer fan chevrons near the pylon work to reduce the strength of the secondary flow induced by the pylon itself, such that the asymmetric merging of the fan and core shear layers is significantly delayed. The effect is to reduce the peak turbulence kinetic energy and shift it downstream, reducing overall noise production. This combined flow and noise prediction approach has yielded considerable understanding of the physics of a fan chevron nozzle designed to include propulsion airframe aeroacoustic interaction effects.

Massey, Steven J.↗

NASA NTRS1981

Comparison of predicted engine core noise with current and proposed aircraft noise certification requirements

Predicted engine core noise levels for subsonic CTOL aircraft engines are compared with measured total aircraft noise levels and to current and proposed federal noise certification requirements. Comparisons are made at FAR-36 measuring stations and take into consideration both full and cutback power operations at takeoff. The spectral shape used for the prediction of core noise is identified as the spectral envelope, with a peak at 400 Hz which is assumed to be shifted in flight by a Doppler shift in frequency. Preceived noise levels are computed for appropriate engine power settings at desired flight conditions, and reductions in sideline noise levels are made to account for jet and airframe shielding effects. Results indicate that core noise can provide a barrier to the proposed EPA stage 4 and 5 federal noise rules for wide-body aircraft, with the most severe core noise problem occurring at takeoff and sideline measuring stations.

Von Glahn, U. H.↗