Search NASA⌕ Search

SEARCH · Search NASA

Results for “BIAXIAL TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

263 records · Page 15

Status of the MeLoDIE experiment, an advanced device for the study of the irradiation creep of LWR cladding with full online capabilities

As a prototype of future instrumented material experiments in the Jules Horowitz Reactor (JHR), the MELODIE project was launched in 2009 by the CEA in collaboration with VTT. Being designed as a biaxial creep experiment with online capability, MELODIE is able to apply an online-controlled biaxial loading on a LWR clad sample up to 120 MPa and to perform an online measurement of its biaxial deformation. An important experimental challenge was to perform reliably accurate measurements under the high nuclear heat load of in-core locations while keeping within their tight space. For that purpose, specific sensors were co-designed with and built by IFE Halden. Manufacturing of the MELODIE components was completed one year ago. The complexity of its in-pile section and of the pressurization system requested a step-by-step tuning of the setup. The toughest part of this process dealt with the Diameter gauge which required a partial redesign to take into account unexpected and unwanted electromagnetic interactions with the hosting device. Final cold performance tests of the on-board instrumentation will be presented. The MELODIE device is now ready and irradiation should start in OSIRIS reactor this spring. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Failure prediction of thin beryllium sheets used in spacecraft structures

The primary objective of this study is to develop a method for prediction of failure of thin beryllium sheets that undergo complex states of stress. Major components of the research include experimental evaluation of strength parameters for cross-rolled beryllium sheet, application of the Tsai-Wu failure criterion to plate bending problems, development of a high order failure criterion, application of the new criterion to a variety of structures, and incorporation of both failure criteria into a finite element code. A Tsai-Wu failure model for SR-200 sheet material is developed from available tensile data, experiments carried out by NASA on two circular plates, and compression and off-axis experiments performed in this study. The failure surface obtained from the resulting criterion forms an ellipsoid. By supplementing experimental data used in the the two-dimensional criterion and modifying previously suggested failure criteria, a multi-dimensional failure surface is proposed for thin beryllium structures. The new criterion for orthotropic material is represented by a failure surface in six-dimensional stress space. In order to determine coefficients of the governing equation, a number of uniaxial, biaxial, and triaxial experiments are required. Details of these experiments and a complementary ultrasonic investigation are described in detail. Finally, validity of the criterion and newly determined mechanical properties is established through experiments on structures composed of SR200 sheet material. These experiments include a plate-plug arrangement under a complex state of stress and a series of plates with an out-of-plane central point load. Both criteria have been incorporated into a general purpose finite element analysis code. Numerical simulation incrementally applied loads to a structural component that is being designed and checks each nodal point in the model for exceedance of a failure criterion. If stresses at all locations do not exceed the failure criterion, the load is increased and the process is repeated. Failure results for the plate-plug and clamped plate tests are accurate to within 2 percent.

Roschke, Paul N.↗

Thermo-mechanical Forming of Al-Mg-Si Alloys: Modeling and Experiments

In an ongoing quest to realize lighter vehicles with improved fuel efficiency, deformation characteristics of the material AA 6016 is investigated. In the first part of this study, material behavior of Al-Mg-Si sheet alloy is investigated under different process (temperature and strain rate) and loading (uniaxial and biaxial) conditions experimentally. Later, warm cylindrical cup deep drawing experiments were performed to study the effect of various parameters on warm forming processes, such as the effect of punch velocity, holding time, temper and temperature on force-displacement response. The plastic anisotropy of the material which can be directly reflected by the earing behavior of the drawn cups has also been studied. Finite element simulations can be a powerful tool for the design of warm forming processes and tooling. Their accuracy will depend on the availability of material models that are capable of describing the influence of temperature and strain rate on the flow stresses. The physically based Nes model is used to describe the influence of temperature and strain rate and the Vegter yield criterion is used to describe the plastic anisotropy of the sheet. Experimental drawing test data are used to validate the modeling approaches.

36 MATERIALS SCIENCE↗

Fracture strength and elastic modulus as a function of porosity for hydroxyapatite and other brittle materials Part I

Porous brittle materials are used as filters, catalyst supports, solid oxide fuel cells and biomedical materials. However the literature on the Weibull modulus, m, versus volume fraction porosity, P, is extremely limited despite the importance of m as a gauge of mechanical reliability. In Part I of this study, m is determined for 441 sintered hydroxyapatite (HA) specimens fractured in biaxial flexure for 0.08 P 0.62. In this study, we analyze a combined data set collected from the literature that represents work from a total of 17 different research groups (including the present authors), eight different materials and more than 1560 oxide and non-oxide specimens, the m versus P plot is Ushaped with a wide band of m values for P < 0.1 (Region I) and P > 0.55 (Region III), and a narrower band of m values in the intermediate porosity region of 0.1 < P < 0.55 (Region II). The limited range of m ( 4 < m < 11) in Region II has important implications since Region II includes the P range for the majority of the applications of porous brittle materials. Part II of this study focuses on the P dependence of the mean fracture strength,< f >, and the Young s modulus E for the HA specimens tested in Part I along with literature data for other brittle materials. Both < f > and E are power law functions of the degree of densification, , where = 1 P/PG and PG is the green (unfired) porosity.

30 DIRECT ENERGY CONVERSION↗

Advancements in Constitutive Model Calibration: Leveraging the Power of Full‐Field DIC Measurements and In Situ Load Path Selection for Reliable Parameter Inference

Accurate material characterization and model calibration are essential for computationally supported high-consequence engineering decisions. Historically, characterization and calibration methods (1) use simplified test specimen geometries and global data, (2) cannot guarantee that sufficient characterization data are collected for a specific model of interest, (3) use deterministic methods that provide best-fit parameter values with no uncertainty quantification, and (4) are sequential, inflexible, and time-consuming. This work brings together several recent advancements into an improved workflow called interlaced characterization and calibration (ICC) that advances the state-of-the-art in constitutive model calibration. The ICC paradigm (1) employs tools to efficiently use full-field data to calibrate high-fidelity material models, (2) aligns the data needed with the data collected by adopting an optimal experimental design protocol, (3) quantifies parameter uncertainty through Bayesian inference and (4) incorporates these advancements into a quasi real-time feedback loop. The ICC framework is demonstrated here on the calibration of a material model using simulated full-field data for an aluminium cruciform specimen being deformed biaxially. The cruciform is actively driven through the myopically preferred load path using Bayesian optimal experimental design, which selects load steps that yield the maximum expected information gain (EIG). Principal component analysis (PCA) is performed on the model predictions of full-field displacements, and fast surrogate models are built to approximate the input-output relationships of the expensive finite element model. Furthermore, the tools developed and demonstrated here show that high-fidelity constitutive models can be efficiently and reliably calibrated with quantified uncertainty, thus supporting credible decision-making and potentially increasing the agility of solid mechanics modelling by enabling utilization of computational simulations at earlier stages of the design cycle.

Bayesian optimal experimental design↗

Inelastic response of metal matrix composites under biaxial loading

Elements of the analytical/experimental program to characterize the response of silicon carbide titanium (SCS-6/Ti-15-3) composite tubes under biaxial loading are outlined. The analytical program comprises prediction of initial yielding and subsequent inelastic response of unidirectional and angle-ply silicon carbide titanium tubes using a combined micromechanics approach and laminate analysis. The micromechanics approach is based on the method of cells model and has the capability of generating the effective thermomechanical response of metal matrix composites in the linear and inelastic region in the presence of temperature and time-dependent properties of the individual constituents and imperfect bonding on the initial yield surfaces and inelastic response of (0) and (+ or - 45)sub s SCS-6/Ti-15-3 laminates loaded by different combinations of stresses. The generated analytical predictions will be compared with the experimental results. The experimental program comprises generation of initial yield surfaces, subsequent stress-strain curves and determination of failure loads of the SCS-6/Ti-15-3 tubes under selected loading conditions. The results of the analytical investigation are employed to define the actual loading paths for the experimental program. A brief overview of the experimental methodology is given. This includes the test capabilities of the Composite Mechanics Laboratory at the University of Virginia, the SCS-6/Ti-15-3 composite tubes secured from McDonnell Douglas Corporation, a text fixture specifically developed for combined axial-torsional loading, and the MTS combined axial-torsion loader that will be employed in the actual testing.

Mirzadeh, F.↗

Neutron Bragg-edge-imaging for strain mapping under in situ tensile loading

Wavelength selective neutron radiography at a cold neutron reactor source was used to measure strain and determine (residual) stresses in a steel sample under plane stress conditions. We present a new technique that uses an energy-resolved neutron imaging system based on a double crystal monochromator and is equipped with a specially developed (in situ) biaxial load frame to perform Bragg edge based transmission imaging. The neutron imaging technique provides a viewing area of 7 cm by 7 cm with a spatial resolution on the order of {approx} 100 {mu}m. The stress-induced shifts of the Bragg edge corresponding to the (110) lattice plane were resolved spatially for a ferritic steel alloy A36 (ASTM international) sample. Furthermore it is demonstrated that results agree with comparative data obtained using neutron diffraction and resistance based strain-gauge rosettes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabric geometry distortion during composites processing

Waviness and tow misalignment are often cited as possible causes of data scatter and lower compression stiffness and strength in textile composites. Strength differences of as much as 40 percent have been seen in composites that appear to have the same basic material and structural properties -- i.e., yarn orientation, yarn size, interlacing geometry. Fabric geometry distortion has been suggested as a possible reason for this discrepancy, but little quantitative data or substantial evidence exists. The focus of this research is to contribute to the present understanding of the causes and effects of geometric distortion in textile composites. The initial part of the study was an attempt to gather qualitative information on a variety of textile structures. Existing and new samples confirmed that structures with a significant direction presence would be more susceptible to distortion due to the compaction process. Thus, uniweaves (fiber vol frac: 54-72 percent) biaxial braids (vf: 34-58 percent) demonstrated very little fabric geometry distortion. In stitched panels, only slight buckling of z-direction stitches was observed, primarily near the surface. In contrast, for structures with high compaction ratios -- e.g., large cylindrical yarns (2.5:1) orpowder towpreg (4:1) -- there were visible distortions where previously smooth and periodic undulations were transformed to abrupt changes in direction. A controlled study of the effect of forming pressure on distortion was conducted on type 162 glass plain weave fabrics. Panels (6 x 6 in) were produced via a resin infusion type setup, but with an EPON 815 epoxy resin. Pressures ranging from hand layup to 200 psi were used (vf: 34-54 percent). Photomicrographs indicated that at pressures up to 50 psi, large changes in thickness were due primarily to resin squeeze out. At higher pressures, when intimate contact was made between the layers, there was some tow flattening and in-plane shifting to optimize nesting. However, even at 200 psi the period and amplitude of the tow undulation remained constant, suggesting that for this relatively fine fabric, distortions from compaction were not a problem. Because of the interest in using larger tows (to reduce cost) and more complex structures, tests were also run on 2D triaxial glass braid (113 yd/lb at 0, 225 yd/lb at +/- 45). Forming pressures of 20, 50, 200, and 500 psi were used, and short block compression tests were run. The 500 psi specimen had a 10 percent decrease in modulus and an almost 50 percent decrease in strength (vs. 20 psi). Because the total fiber wgt/panel was kept constant, the thickness varied from 0.32 to 0.22 in (49-70 percent vf). Yet, the strength value is clearly below what would be expected, even with the decrease in thickness. Photomicrographs of these samples will be taken to determine if more fabric distortion exists in the 500 psi specimens. Finally, because the ultimate goal is to be able to predict and control distortion in a variety of textile structures, a model compaction test was developed to directly measure the deformation of the tows during compaction. Layers of dry glass fabric were placed in a mold with a clear plexiglass window. The yarn amplitude and period was then calculated using image analysis of the videotaped deformation. Preliminary tests demonstrated the feasibility of this technique for simple fabrics with large tows.

Chen, Julie↗

Durable, Impermeable Brazes for Solid Oxide Fuel Cells (Final Report)

To develop a new braze to replace the current state-of-the-art Ag-CuO reactive air braze (RAB), two approaches were proposed: 1) development of a new, self-passivating, silver-free braze and 2) development of a CuO-free, silver-based braze. For the first approach, an integrated computational-experimental method was used. Thermo-Calc® was utilized to quickly screen through hundreds of alloy systems to identify candidate braze compositions with the appropriate melting ranges. Material compositions, melting ranges, mechanical properties, oxidation resistance, and wetting characteristics of the candidate alloys were then analyzed experimentally. Substrate surface pre-treatments, active element additions, and novel brazing schemes were also investigated. Unfortunately, the current study failed to identify new silver-free braze compositions suitable for SOFC applications. To help measure the passivation characteristics of surface passivating braze oxide coatings, work was conducted to demonstrate, for the first time, that a variety of disparate and technologically-relevant thermal, mechanical, and electrochemical oxygen-exchange thin film material properties could all be obtained from in situ , current-collector-free wafer curvature measurements. Specifically, temperature or oxygen partial pressure induced changes in the curvature of 230 nm thick (100)-oriented Pr 0.1 Ce 0.9 O 1.95_x (10PCO) films atop 200 mm thick single crystal yttria stabilized zirconia or magnesium oxide substrates were used to measure the biaxial modulus, Young’s modulus, thermal expansion coefficient, thermochemical expansion coefficient, oxygen nonstoichiometry, chemical oxygen surface exchange coefficient, oxygen surface exchange resistance, thermal stress, chemical stress, thermal strain, and chemical strain of the model mixed ionic electronic conducting material 10PCO. The (100)-oriented thin film 10PCO thermal expansion coefficient, thermo-chemical expansion coefficient, oxygen nonstoichiometry, and Young’s modulus (which is essentially constant, at ~200 MPa, over the entire 280–700 °C temperature range in air) measured here were similar to those from other bulk and thin film 10PCO studies. In addition, the measured PCO10 oxygen surface coefficients were in agreement with those reported by other in situ , current collector- free techniques. However, the measured PCO10 oxygen surface exchange coefficients were significantly lower than those obtained from literature studies with large amounts of intentional or inadvertent precious metal surface coverage/contamination (suggesting that uncontaminated (100)-oriented 10PCO may not be a desirable SOFC cathode material). Taken together, this highlighted the advantages of using a sample’s mechanical response, instead of the more traditional electrical response, to probe the electrochemical properties of the ion-exchange materials used in solid oxide fuel cell, solid oxide electrolysis cell, gas-sensing, battery, emission control, water splitting, water purification, and other electrochemically-active devices. For the second approach, a novel silver-nickel brazing method was developed. It was demonstrated that transient porous nickel interlayers, instead of reactive element additions, could be used to promote Ag wetting on yttria stabilized zirconia (YSZ) and produce high-quality YSZ stainless steel (SS) braze joints. Mechanical tests on these reactive-element-free, silver-based SOFC braze joints, both before and after 500 hours of 750°C oxidation in air, showed that the braze and braze interface strength were higher than the underlying YSZ|NiO-YSZ substrate. The microstructural and compositional evolution of SS|Ag-Ni|YSZ braze joints exposed to dual atmosphere (air on one side and 4%H 2 -96%N 2 on the other side) for 300 hours of isothermal 750 °C aging and 300 25°C/min 35-830 °C rapid thermal cycles were compared to a Ag-3CuO braze joint. In contrast to conventional Ag-CuO RAB brazes, the Ag-Ni brazes remained pore free and well bonded, suggesting that Ag-Ni brazes may be more suitable for long term SOFC operation than Ag-CuO brazes. Other applications inspired by the silver-nickel wetting process on various ceramic substrates were also explored. In support of efforts to identify new CuO-free Ag-based brazes, density functional theory and ab initio molecular dynamics calculations were performed to 1) understand silver wetting on YSZ, and 2) identify new oxides to promote silver wetting on YSZ. These simulations found that while the formation of dissolved oxygen clusters within molten silver at the YSZ interface promoted wetting, much greater wetting angle reductions came from the formation of metal oxide interlayers at the Ag-YSZ interface. Through the development of a simple descriptor, many simple metal oxides (single cation) were examined. Unfortunately, their ability to promote Ag wetting were less than that of CuO. However, expanding the search to multi-cation oxides led to several promising candidates, such as CuAlO 2 , CuGaO 2 , and Cu 3 TiO 4 ; all of which are also stable in the reducing SOFC conditions. Depending upon their solubility in molten Ag, these newly-identified oxides could either be pre-applied as wetting promoting interlayers or directly incorporated into Ag to form new reactive air brazes.

36 MATERIALS SCIENCE↗

Biaxial Creep Behavior of Nb-Modified Zircaloys

Zr-Nb alloys are used as cladding materials to encapsulate radioactive fuel in nuclear reactors. They possess excellent corrosion resistance at high temperatures making it possible to achieve high fuel burn-up directly increasing the thermal efficiency of the reactor. While they are commonly used in recrystallized (Rx) form in boiling water reactors, there is a need to understand the effect of cold work and stress relief (CWSR) on biaxial creep characteristics of these materials due to their use in pressurized water reactors. In this study, the biaxial creep behaviors of as-received Zr-Nb alloys, HANA and Zirlo, have been investigated at 500 and 400 0C respectively using internally pressurized tubing superimposed with axial load under varied hoop (s?) to axial (sz) stress ratios of 0 to 2 while monitoring both the axial and hoop strains using an LVDT and a laser telemetric extensometer respectively. The crystallographic textures and creep loci of these as-received Zr-Nb alloys have been evaluated to correlate with the previous studies on recrystallized HANA4 and CWSR Zircaloy-4. The creep locus of HANA4 was found to be unaffected by initial state (CWSR or Rx) and showed close correspondence to planar isotropy while the creep locus of CWSR Zirlo exhibited more resistance to axial deformation than diametrical as per CWSR Zircaloy4 reported earlier. These differences are shown to arise from grain shape anisotropy of CWSR Zirlo and Zircaloy4. The simulated creep loci using crystallite orientation distribution functions (CODFs) in conjunction with prism slip models, showed excellent agreement with experimental results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Strategic Buffer Layer Development for YBCO Coated Conductors

We have developed a simplified buffer layer architecture for the rolling-assisted biaxially textured substrates (RABiTS) template approach. The overall purpose of this research is to enable potentially a low-cost, high throughput and high yield manufacturing processes for buffer fabrication and to gain fundamental understanding of the growth of buffer layers for RABiTS templates. This understanding is critical to the development of a reliable, robust, and long-length manufacturing process for second generation wires. In this study, efforts are being made to either reduce the number of vacuum deposited layers or to replace one or more of these vacuum deposited layers with a solution based layer. We have chosen Gd{sub 2}O{sub 3} - ZrO{sub 2} system as a potential barrier layer for this study. We have deposited epitaxial Gadolinia Stabilized Zirconia (GSZ) (Zr{sub 1-x}Gd{sub x}O{sub y}; x = 0-1) films on 30-nm thick e-beam evaporated Y{sub 2}O{sub 3} seeded Ni-W (3 at. %) (Ni-3W) substrates using a metal-organic decomposition (MOD) process. Detailed X-ray studies indicated that all of the MOD-GSZ layers were cube textured and both in-plane and out-of-plane lattice parameters increases linearly with increasing the Gd content. We have also developed process conditions for reactively sputter deposited epitaxial Gd{sub 2}Zr{sub 2}O{sub 7} (Gadolinium Zirconium Oxide (GZO); Zr{sub 1-x}Gd{sub x}O{sub y} (x = 0.5)) films on the e-beam evaporated Y{sub 2}O{sub 3}/Ni - 3W substrates. YBCO films with a critical current density J{sub c} of 2.14 times 10{sup 6} A/cm{sup 2} and 1.4 times 10{sup 6} A/cm{sup 2} at 77 K and self-field were grown on the newly developed architectures of Gd{sub 2}Zr{sub 2}O{sub 7}/Y{sub 2}O{sub 3}/Ni - 3W and Zr{sub 1-x}Gd{sub x}O{sub y} (x = 0.2)/Y{sub 2}O{sub 3}/Ni - 3W substrates, respectively using a pulsed laser deposition (PLD) process. This work promises a route for producing cost-effective simplified buffer architectures for the RABiTS-based YBCO coated conductors.

36 MATERIALS SCIENCE↗