SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Here, we report on a study of the effects of nanoconfinement on polymer chain dynamics within the framework developed by Muthukumar [Muthukumar, M. (1991). Journal of Non-Crystalline Solids, 131, 654-666.], who suggests that there is an entropically controlled dynamical regime between the Rouse and the reptation regimes that affects the power law dependence on molecular weight of the transport properties.
HRL Laboratories and General Motors (GM), pursued this effort to increase the efficiency of internal combustion engines (ICEs) by developing and implementing temperature-following thermal barrier coatings (TBCs) to decrease heat loss from the combustion chamber. HRL developed microsphere TBCs based on hollow high-temperature alloy spheres with average diameter of 50 μm and wall thickness ~1 μm (microspheres) that achieve unprecedented low thermal conductivity and heat capacity (10X lower than the state of the art) while offering exceptional environmental and mechanical resistance.> In current ICEs, approximately 29% of the fuel’s energy is lost to the cooling system and about 22% goes into moving the car. By limiting heat losses from the combustion chamber with insulating coatings, fuel energy can be redirected into additional piston work and into the exhaust stream. The additional energy that goes into the exhaust stream can be turned into useful work through the use of an exhaust energy recovery device, such as turbocompounding and/or through driving a turbocharger to increase the power density of the engine allowing downsizing. Insulating coatings for piston crowns have been pursued in the past, but previous materials—typically ceramics—exhibited low thermal conductivity but retained high heat capacity. Such materials reduce heat losses but stabilize at a high surface temperature. The high surface temperature heats the incoming gases, which lowers volumetric efficiency and increases propensity for knock, resulting in degraded engine performance. This program developed an innovative new material that combines low thermal conductivity with low heat capacity. These unique properties allow it to follow rapid changes in gas temperature during each combustion cycle. A metallic microsphere TBC has been demonstrated that exhibits increased surface temperature during the combustion period, resulting in reduced heat transfer losses, while still returning to a low surface temperature during the gas exchange period. A 10X lower thermal conductivity and heat capacity than state-of-the-art thermal barrier coatings has been demonstrated. These unprecedented thermal properties are achieved through the coating architecture, which consists of closed pores on the microscale and exhibits a total porosity of 90% to 95%. By selecting a high-temperature nickel alloy as the coating material, the ductility and strength of metals can be harnessed to achieve much better durability and damage tolerance than brittle ceramic coatings can achieve.
Epitaxial multilayer heterostructures of Sc x Al 1–x N/GaN with Sc contents x = 0.11–0.45 are found to exhibit significant differences in structural quality, chemical impurity levels, and electronic properties depending on the starting Sc source impurity levels. A higher purity source leads to a 2–3 orders of magnitude reduction in the carbon, oxygen, and fluorine unintentional doping densities in MBE-grown Sc x Al 1–x N/GaN multilayers. Electrical measurements of Sc x Al 1–x N/n + GaN single heterostructure barriers show a 5–7 orders of magnitude reduction in the electrical leakage for films grown with a higher purity Sc source at most Sc contents. The measured chemical and electrical properties of epitaxial Sc x Al 1–x N highlight the importance of the starting Sc source material purity for epitaxial device applications that need these highly piezoelectric and/or ferroelectric transition-metal nitride alloys.
Abstract Interfaces, the boundary that separates two or more chemical compositions and/or phases of matter, alters basic chemical and physical properties including the thermodynamics of selectivity, transition states, and pathways of chemical reactions, nucleation events and phase growth, and kinetic barriers and mechanisms for mass transport and heat transport. While progress has been made in advancing more interface‐sensitive experimental approaches, their interpretation requires new theoretical methods and models that in turn can further elaborate on the microscopic physics that make interfacial chemistry so unique compared to the bulk phase. In this review, we describe some of the most recent theoretical efforts in modeling interfaces, and what has been learned about the transport and chemical transformations that occur at the air–liquid and solid–liquid interfaces. This article is categorized under: Structure and Mechanism > Reaction Mechanisms and Catalysis Structure and Mechanism > Computational Materials Science Software > Quantum Chemistry Software > Simulation Methods
The regulation of reactive centers by involving the participation of lattice oxygen has been reported as an effective strategy for lowering the reaction barrier for the oxygen evolution reaction (OER). However, the control of the OER pathway by taking advantage of the intrinsic properties of catalysts remains a challenging task. Herein, we adopt perovskite nickelate (i.e., NdNiO3 (NNO)) and establish the link between structural anisotropy and the OER catalytic mechanism. The results elucidate that NNO with (100), (110), and (111) orientations display similar oxidative states and metal–oxygen covalency characteristics but distinct OER activities following the order of (100) > (110) > (111). Density function theory (DFT) results confirm that film orientation is a critical determinant of the reaction mechanism. The OER on (100)-NNO favors proceeding via a lattice-oxygen-mediated mechanism (LOM). In contrast, the reaction on (110)-NNO and (111)-NNO follows the adsorbate evolution mechanism (AEM). The anisotropic oxygen vacancy formation energy and stability are strongly correlated to the reaction mechanism and performance, which can be described in brief by the metal–oxygen bond valence. Furthermore, our results are a step toward achieving the long-sought convenient approach to tune the OER mechanism, which is applicable for a wide range of sustainable energy-related devices.
Crystal field (CF) control of rare-earth (RE) ions has been employed to minimize decoherence in qubits and to enhance the effective barrier of single-molecule magnets. The CF approach has been focused on the effects of symmetry on dynamic magnetic properties. Herein, the magnitude of the CF is increased via control of the RE oxidation state. The enhanced 4f metal-ligand covalency in Pr 4+ gives rise to CF energy scales that compete with the spin-orbit coupling of Pr 4+ and thereby shifts the paradigm from the ionic ζ SOC >> V CF limit, used to describe trivalent RE-ion, to an intermediate coupling (IC) regime. We examine Pr 4+ -doped perovskite oxide lattices (BaSnO 3 and BaZrO 3 ). These systems are defined by IC which quenches orbital angular momentum. Therefore, the single-ion spin-orbit coupled states in Pr 4+ can be chemically tuned. We demonstrate a relatively large hyperfine interaction of A iso = 1800 MHz for Pr 4+ , coherent manipulation of the spin with Q M = 2Ω R $T$ m reaching up to ~400 for 0.1Pr:BSO at $T$ = 5 K, and significant improvement of the temperature at which $T$ m is limited by $T$ 1 ($T$* = 60 K) compared to other RE ion qubits.
The capture dynamics of a H atom and isotopic variants [D, T and Q (hypothetical isotope of mass equal to four times the mass of H)] by a superfluid helium nanodroplet (HeND) has been investigated theoretically. The HeND (T = 0.37 K) is ( 4 He) N=400 and a mean field quantum hybrid approach [TDDFT (helium) + quantum wave packet (H, D, T or Q)] at zero angular momentum, is used to explore a rather wide range of very low initial kinetic energies (E k,0 ≈ 10–150 K). The analysis of the capture mechanism shows the existence of a dynamical barrier and a dynamical minimum that play key roles to understand the time evolution of the capture, especially the former property. In general, the H atom shows a different behavior from the other isotopes, with the behavior of T and Q being very similar to each other and the D atom behaving inbetween H and T. Besides, it is worth noting that, in principle, at the very low initial kinetic energies considered only “short” and “long” lived atom⋯HeND collision complexes are formed, i.e., in the atom-helium nanodroplet collision only the temporary capture of the atom takes place. The different behaviors observed have been interpreted considering the faster motion of the H atom when colliding with ( 4 He) N=400 and the more quantum character of the H behavior both due to its significantly lower mass. As far as we know, this is the first quantum dynamics study carried out on the collision of light atoms with HeNDs at very low energies.
Polyurethane foam is used as a thermal insulator, fire protective material, and impact absorber in the 9977 shipping package. The 9977 shipping package is used to transport special nuclear materials (SNM), and store SNM in the K-area complex at the Savannah River Site. The primary fire-retardant mechanism in the foam is that it produces intumescent char when exposed to high temperatures. Intumescence occurs in the direction of heat application and can allow the foam to “repair” cracks in the event of a mechanical impact, in addition to serving as a secondary thermal barrier with decreased heat conductivity. Because the foam is being used for long-term storage applications, it is vital that it retain its physical, thermal, and mechanical properties over the course of time and with the events of exposure of heat and irradiation. The goal of this project was to determine the effects of gamma irradiation on the thermal properties of polyurethane foam, both in terms of cumulative irradiation and rate of irradiation. At the dose rates and cumulative doses of irradiation measured, there was no correlation between higher cumulative irradiation and thermal stability, specific heat capacity, or chemical structure. Based on the results of the experiments, the fire protective properties in the 9977 shipping containers should be retained with the expected amount of radiation exposure.
Quality control (QC) for both polymer electrolyte membrane fuel cell and electrolysis membrane electrode assembly (MEA) materials is a key challenge for scale-up and cost reduction. Developing methods for detecting defects, as well as measuring critical material properties and understanding the impact of as-manufactured variations in these materials on cell performance and lifetime, are critical barriers. To help address these needs, the National Research Council Canada (NRC), Fraunhofer Institute for Solar Energy Systems (ISE), and the National Renewable Energy Laboratory (NREL) have organized and facilitated a series of workshops on the topic, bringing together industry, academia, and research institutions from North America and Europe. Prior workshops in Canada and Germany have focused on the status of quality tool capabilities and identification of needed developments for fuel cells. These meetings have garnered an excellent response and follow-on attendance, with over 100 unique attendees.
Beta-Ga2O3 has emerged as a leading candidate for next-generation power electronics, radio frequency (RF) switches, and extreme environment electronics due to a wide band gap (4.6 - 4.9 eV), high dopability (approximately 40 meV activation energy for an isolated silicon donor), and melt growth characteristics resulting in commercially available 4-inch substrates and commercial demonstrations of 6-inch substrates by multiple techniques. The (100) surface of Ga2O3 is highly desirable from a device and epitaxy standpoint - bulk growth of (100) material is more scalable than (010), the surface is nearly lattice-matched to p-type partner NiO, and Al2O3 incorporates at higher concentrations without phase separation. More importantly, the impact ionization coefficients along the [100] direction are low, leading to the highest possible critical fields. This is advantageous compared to the current state of the art, (001), due to reduced surface defects and increased possible breakdown voltage. However, the epitaxial growth rate on (100) surfaces is less than 10% of other faces due to weak bonding and favorable desorption, and on-axis (100) growth easily forms twin domains. Recent demonstrations have shown growth rate improvements from 0.4 nm/min to 1.5 nm/min by growing on (100) wafers that are offcut 6 degrees in the -c direction. These films show step-flow growth from (20-1) step-edges and high electron mobility due to suppressed twins. Despite these exciting results, offcuts greater than 6 degrees have not been explored due to the waste associated with grinding and polishing large offcuts. In this talk we will discuss the molecular beam epitaxy (MBE) growth and properties of Beta-Ga2O3 grown on (100) substrates offcut in the -c direction up to 13.4 degrees. These large offcuts are enabled by edge-fed film-defined growth (EFG) where the offcut is grown into the surface by pulling the crystal through the EFG die with the seed crystal rotated by the desired offcut angle. We will demonstrate that 13.4 degrees offcut substrates still exhibit a terraced (100) surface, and that a >10x increase (>5 nm/min) in growth rate is achieved. As previously reported on lower offcuts, we observe reversal of substrate twin domains around the (001) direction at the substrate-epilayer interface. We will discuss electrical properties including record-low (by MBE) unintentional doping densities of < 5E15 cm-3 and critical breakdown field in Schottky barrier diodes comparable with state-of-the-art (001) Ga2O3 without edge termination.
Transition metal oxides not only exhibits novel magnetic properties but also provides outstanding ionic transports. Ionic conductors have great potential for interesting tunable physical properties via ionic liquid gating and novel energy storage applications such as all-solid-state lithium batteries. In particular, low migration barriers and high hopping attempt frequency are the keys to achieve fast ion diffusion in solids. Taking advantage of the oxygen-vacancy channel in Li x Sr 2 Co 2 O 5 , we show that migration barriers of lithium ion are as small as 0.28–0.17 eV depending on the lithium concentration rates. Our first-principles calculation also investigated hopping attempt frequency and concluded the room temperature ionic diffusivity and ion conductivity are high as 10 −7 –10 −6 cm 2 s −1 and 10 −3 –10 −2 Scm −1 , respectively, which outperform most of perovskite-type, garnet-type, and sulfide Li-ion solid-state electrolytes. This work proves Li x Sr 2 Co 2 O 5 as a promising super-ionic conductor.
Fine-grained spectral properties of quantum Hamiltonians, including both eigenvalues and their multiplicities, provide useful information for characterizing many-body quantum systems as well as for understanding phenomena such as topological order. Extracting such information with small additive error is #BQP-complete in the worst case. In this work, we introduce QFAMES (quantum filtering and analysis of multiplicities in eigenvalue spectra), a quantum algorithm that efficiently identifies clusters of closely spaced dominant eigenvalues and determines their multiplicities under physically motivated assumptions, which allows us to bypass worst-case complexity barriers. QFAMES also enables the estimation of observable expectation values within targeted energy clusters, providing a powerful tool for studying quantum phase transitions and other physical properties. We validate the effectiveness of QFAMES through numerical demonstrations, including its applications to characterizing quantum phases in the transverse-field Ising model and estimating the ground-state degeneracy of a topologically ordered phase in the two-dimensional toric code model. We also generalize QFAMES to the setting of mixed initial states. Our approach offers rigorous theoretical guarantees and significant advantages over existing subspace-based quantum spectral analysis methods, particularly in terms of the sample complexity and the ability to resolve degeneracies.
The integration of machine learning techniques in materials discovery has become prominent in materials science research and has been accompanied by an increasing trend towards open data and open-source tools to propel the field. Despite the increasing usefulness and capabilities of these tools, developers neglecting to follow reproducible practices presents a significant barrier for other researchers looking to use or build upon their work. In this study, we investigate the challenges encountered while attempting to reproduce a section of the results presented in “A general-purpose machine learning framework for predicting properties of inorganic materials.” Our analysis identifies four major categories of challenges: (1) reporting software dependencies, (2) recording and sharing version logs, (3) sequential code organization, and (4) clarifying code references within the manuscript. The result is a proposed set of tangible action items for those aiming to make material informatics tools accessible to, and useful for the community.
Abstract Constructing an artificial solid electrolyte interphase (SEI) on lithium metal electrodes is a promising approach to address the rampant growth of dangerous lithium morphologies (dendritic and dead Li 0 ) and low Coulombic efficiency that plague development of lithium metal batteries, but how Li + transport behavior in the SEI is coupled with mechanical properties remains unknown. We demonstrate here a facile and scalable solution-processed approach to form a Li 3 N-rich SEI with a phase-pure crystalline structure that minimizes the diffusion energy barrier of Li + across the SEI. Compared with a polycrystalline Li 3 N SEI obtained from conventional practice, the phase-pure/single crystalline Li 3 N-rich SEI constitutes an interphase of high mechanical strength and low Li + diffusion barrier. We elucidate the correlation among Li + transference number, diffusion behavior, concentration gradient, and the stability of the lithium metal electrode by integrating phase field simulations with experiments. We demonstrate improved reversibility and charge/discharge cycling behaviors for both symmetric cells and full lithium-metal batteries constructed with this Li 3 N-rich SEI. These studies may cast new insight into the design and engineering of an ideal artificial SEI for stable and high-performance lithium metal batteries.
Abstract The state‐of‐the‐art magnetic tunnel junction, a cornerstone of spintronic devices and circuits, uses a magnesium oxide tunnel barrier that provides a uniquely large tunnel magnetoresistance at room temperature. However, the wide bandgap and band alignment of magnesium oxide‐iron systems increases the resistance‐area product and creates variability and breakdown challenges. Here, the authors study using first principles narrower‐bandgap scandium nitride (ScN) transport properties in magnetoresistive junctions in comparison to magnesium oxide. The results show a high magnetoresistance in Fe/ScN/Fe via Δ 1 and symmetry filtering with low wave function decay rates, suggesting scandium nitride could be a new barrier material for spintronic devices.
The hydrogen infrastructure involves hydrogen production, storage and delivery for utilization with clean energy applications. Hydrogen ingress into structural materials can be detrimental due to corrosion and embrittlement. To enable safe operation in applications that need protection from hydrogen isotopes, this review article summarizes most recent advances in materials design and performance characterization of barrier coatings to prevent hydrogen isotopes’ absorption ingress and permeation. Barriers are crucial to prevent hydride formation and unwanted hydrogen effects to increase safety, materials’ lifetime and reduce cost for applications within nuclear and renewable energy. The coating may be applied on a material that requires protection from hydrogen pick-up, transport and hydride formation in hydrogen storage containers, in pipelines, spent nuclear fuel storage or in nuclear reactors. While existing, commercial coatings that have been much in use may be satisfactory for various applications, it is desirable to evaluate whether alternative coating concepts can provide a greater resistance to hydrogen isotope permeation along with other improved properties, such as mechanical strength and thermal resistance. The information presented here is focusing on recent findings within the past 5–7 years of promising hydrogen barriers including oxides, nitrides, carbon, carbide, MAX-phases and metals and their mechanical strength, hydrogen pick-up, radiation resistance and coating manufacturing techniques. A brief introduction to hydrogen permeation is provided. Knowledge gaps were identified to provide guidance for material’s research prospects.
Density functional theory-based thermodynamic modeling was performed to determine the effect of humidity and H 2 /O 2 gas pressure on the defect chemistry and transport properties of proton conducting oxide BaZr 1-x Y x O 3-δ (x ≤ 0.1) in the temperature range of 800–1200K, relevant for solid oxide fuel/electrolysis cell applications. The first-principles charge defect analysis was carried out to obtain the defect energetic ensembles as a function of Fermi level as well as the dependence of the hydration and oxidation reaction energies on complex defect-dopant configurations. It is shown that oxygen vacancies introduced to compensate for the extra Ba vacancies may cause a slight increase in the concentration of hydroxyl and proton species upon hydration of Ba deficient BaZr 1-x Y x O 3-δ , while the overall proton diffusivity is predicted to decrease with increased proton hopping barriers upon trapping near the Ba vacancies. The developed defect model is further demonstrated to be able to describe the bulk defect chemistry and transport properties of BaZr 0.9 Y 0.1 O 3-δ under the solid oxide cell operating conditions. Finally, the theoretical framework developed in this work further allows the inclusion of configurational, energetic and electronic characteristics of the defects that can be used as a complementary tool to experimental measurements for testing various mechanistic pathways or to provide essential mechanistic data.
Here, we investigate the Joule expansion of nonintegrable quantum systems that contain bosons or spinless fermions in one-dimensional lattices. A barrier initially confines the particles to be in half of the system in a thermal state described by the canonical ensemble and is removed at time t = 0. We investigate the properties of the time-evolved density matrix, the diagonal ensemble density matrix, and the corresponding canonical ensemble density matrix with an effective temperature determined by the total energy conservation using exact diagonalization. The weights for the diagonal ensemble and the canonical ensemble match well for high initial temperatures that correspond to negative effective final temperatures after the expansion. At long times after the barrier is removed, the time-evolved Rényi entropy of subsystems bigger than half can equilibrate to the thermal entropy with exponentially small fluctuations. The time-evolved reduced density matrix at long times can be approximated by a thermal density matrix for small subsystems. Few-body observables, like the momentum distribution function, can be approximated by a thermal expectation of the canonical ensemble with strongly suppressed fluctuations. The negative effective temperatures for finite systems go to non-negative temperatures in the thermodynamic limit for bosons, but there is a true thermodynamic effect for fermions, which is confirmed by finite-temperature density matrix renormalization group calculations. We propose the Joule expansion as a way to dynamically create negative temperature states for fermion systems with repulsive interactions.