Search NASA⌕ Search

SEARCH · Search NASA

Results for “Boundary layer thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Differential analysis for the turbulent boundary layer on a compressor blade element (including boundary-layer separation)

A two-dimensional differential analysis is developed to approximate the turbulent boundary layer on a compressor blade element with strong adverse pressure gradients, including the separated region with reverse flow. The predicted turbulent boundary layer thicknesses and velocity profiles are in good agreement with experimental data for a cascade blade, even in the separated region.

Schmidt, J. F.↗
NASA NTRS1974

Venting characteristics of gaseous helium and nitrogen discharging into a free stream at Mach numbers from 0.60 to 1.57

An experimental investigation was conducted in the Lewis Research Center 8- by 6-Foot Supersonic Wind Tunnel to compare the effects on discharge coefficient of venting gaseous helium and gaseous nitrogen into a free stream. The test was conducted from Mach 0.06 to 1.57 with the vent mounted in a flat plate. The plate was strut mounted to the tunnel ceiling and at a 0 angle of attack. The gases were discharged from a plenum chamber through a 2.54-centimeter (1.00-in.) diameter vent. The ratio of local static pressure to plenum pressure was varied from 0.51 to 0.975. The ratio of boundary layer thickness to vent diameter varied from a maximum of 1.34 at Mach 0.60 to a minimum of 0.55 at Mach 1.37.

Johns, A. L.↗
NASA NTRS1974

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle mounted high angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of a F-106 in a wind tunnel. A 19- to 1-range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight, the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by boattail number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1974

Exhaust-nozzle characterisitcs for a twin-jet variable-wing-sweep fighter airplane model at Mach numbers to 2.2

A wind-tunnel investigation has been conducted to determine the exhaust-nozzle aerodynamic and propulsive characteristics for a twin-jet variable-wing-sweep fighter airplane model. The powered model was tested in the Langley 16-foot transonic tunnel and in the Langley 4-foot supersonic pressure tunnel at Mach numbers to 2.2 and at angles of attack from about minus 2 to 6 deg. Compressed air was used to simulate the nozzle exhaust flow at values of jet total-pressure ratio from approximately 1 (jet off) to about 21. Effects of configuration variables such as speed-brake deflection, store installation, and boundary-layer thickness on the the nozzle characteristics were also investigated.

Reubush, D. E.↗
NASA NTRS1973

Effect of the acoustic boundary layer on the wave propagation in ducts

An analysis is presented for the wave propagation in two-dimensional and circular lined ducts taking into account the effects of viscosity in both the mean and the acoustic problems. The method of composite expansions is used to express each acoustic flow quantity as the sum of an inviscid part and a boundary layer part insignificant outside a thin layer next to the wall. The problem is reduced to solving a second-order ordinary differential equation for the pressure perturbation as in the inviscid acoustic case but with a modified specific wall admittance. An analytic expression is presented for the variation of the modified admittance with the wall and flow parameters, such as the acoustic boundary layer thickness, the mean velocity and temperature gradients at the wall, the frequency of oscillation, and the wavelength.

Nayfeh, A. H.↗
NASA NTRS1974

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle-mounted high-angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of an F-106 in a wind tunnel. A 19-to-1 range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by Reynolds number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1974

On the development of noise-producing large-scale wavelike eddies in a turbulent jet

The development of large-scale wavelike eddies in a two-dimensional turbulent jet was studied. The basic mean flow develops from a mixing region type with an initial specified boundary layer thickness into a fully developed jet. The role of the varicose and sinuous modes as these develop in a growing mean flow is brought out. In general, it was found, for a given frequency parameter, the varicose mode has a shorter streamwise lifetime than the sinuous mode. The latter, for lower frequency ranges, persists past the end of the potential core only to be subject to dissolution by the more enhanced fine scale turbulent activity in that region.

Merkine, L. O.↗
NASA NTRS1975

Wind tunnel measurements in the wake of a simple structure in a simulated atmospheric flow

Measurements of longitudinal mean velocity and turbulence intensity were made in the wake of a rectangular model building in a simulated atmospheric boundary-layer wind. The model building was a 1:50 scale model of a structure used in a wake measurement program at the George C. Marshall Space Flight Center 8-tower boundary-layer facility. The approach wind profile and measurement locations were chosen to match the field site conditions. The wakes of the building in winds from azimuths of 0 and 47 degrees referenced to the normal to the building long axis were examined. The effect of two lines of trees upwind of the building on the wake and the importance of the ratio of the building height to boundary-layer thickness on the extent of the wake were determined.

Hansen, A. C.↗
NASA NTRS1975

Reynolds number effects on boattail drag of exhaust nozzles from wind tunnel and flight tests

A family of nacelle mounted high angle boattail nozzles was tested to investigate Reynolds number effects on drag. The nozzles were flown on a modified F-106B and mounted on scale models of an F-106 in a wind tunnel. A 19- to 1-range of Reynolds number was covered as a result of the large size differences between models and by flying over a range of altitude. In flight the nozzles were mounted behind J-85 turbojet engines. Jet boundary simulators and a powered turbojet engine simulator were used on the wind tunnel models. Data were taken at Mach numbers of 0.6 and 0.9. Boattail drag was found to be affected by Reynolds number. The effect is a complex relationship dependent upon boundary layer thickness and nozzle boattail shape. As Reynolds number was increased from the lowest values obtained with scale models, boattail drag first increased to a maximum at the lowest flight Reynolds number and then decreased.

Wilcox, F. A.↗
NASA NTRS1975

On the development of noise-producing large-scale wavelike eddies in a plane turbulent jet

The paper studies the development of large-scale wavelike eddies in a two-dimensional turbulent jet, extending earlier work on the mixing region (Liu, 1974). The basic mean flow developes from one of mixing-region type with an initially specified boundary-layer thickness into a fully developed jet. This study brings out the role of the varicose and sinuous modes as they develop in a growing mean flow. In general, it is found that, for a given frequency parameter, the varicose mode has a shorter streamwise lifetime than the sinuous mode. For lower frequencies, the latter persists past the end of the potential core only to become subject to dissipation by the enhanced fine-scale turbulent activity in that region.

Merkine, L.-O.↗
NASA NTRS1975

Theoretical face pressure and drag characteristics of forward-facing steps in supersonic turbulent boundary layers

A theoretical investigation of the pressure distributions and drag characteristics was made for forward facing steps in turbulent flow at supersonic speeds. An approximate solution technique proposed by Uebelhack has been modified and extended to obtain a more consistent numerical procedure. A comparison of theoretical calculations with experimental data generally indicated good agreement over the experimentally available range of ratios of step height to boundary layer thickness from 7 to 0.05.

Patel, D. K.↗
NASA NTRS1975

A study of sound generation in subsonic rotors, volume 1

A model for the prediction of wake related sound generation by a single airfoil is presented. It is assumed that the net force fluctuation on an airfoil may be expressed in terms of the net momentum fluctuation in the near wake of the airfoil. The forcing function for sound generation depends on the spectra of the two point velocity correlations in the turbulent region near the airfoil trailing edge. The spectra of the two point velocity correlations were measured for the longitudinal and transverse components of turbulence in the wake of a 91.4 cm chord airfoil. A scaling procedure was developed using the turbulent boundary layer thickness. The model was then used to predict the radiated sound from a 5.1 cm chord airfoil. Agreement between the predicted and measured sound radiation spectra was good. The single airfoil results were extended to a rotor geometry, and various aerodynamic parameters were studied.

Chalupnik, J. D.↗
NASA NTRS1976

A normal shock-wave turbulent boundary-layer interaction at transonic speeds

Experimental results, including surveys of the mean and fluctuating flow, and measurements of surface pressure, skin friction, and separation length, are compared with solutions to the Navier-Stokes equations utilizing various algebraic eddy viscosity models to describe the Reynolds shear stresses. The experimental data, obtained at a free-stream Mach number of 1.5 and Reynolds numbers between 10 million and 80 million, show that a separated zone forms near the foot of the shock and that its length is proportional to the initial boundary-layer thickness; that a supersonic region forms downstream of the shock; and that the shear stress increases significantly through the interaction and subsequently decays downstream. The computations adequately represent the qualitative features of the flow field throughout the interaction but quantitatively underpredict the extent of separation and the downstream level of skin friction.

Mateer, G. G.↗
NASA NTRS1976

Wake-related sound generation from isolated airfoils

A model for the prediction of wake-related sound generation by a single airfoil is presented which assumes that the net force fluctuation on an airfoil can be expressed in terms of the net momentum fluctuation in the near wake of the airfoil. The model predicts a forcing function for sound generation which is related to the spectra of the two-point velocity correlations in the turbulent region near the airfoil trailing edge. Cross spectra were obtained from correlations of the longitudinal and transverse components of turbulence in the wake of a 36-in. chord airfoil in a wind tunnel using x-probe hot-wire sensors. Additional data were obtained from a 10-in. chord airfoil in a free-jet facility. Based on results from these tests, a scaling model was developed using the turbulent boundary-layer thickness as the primary length measure. The model was used to predict the sound radiated from a 2-in. chord airfoil for which acoustical data was available; good agreement was obtained both in level and spectral shape. The single-airfoil result is extended to a rotor geometry, and comparisons are studied for various aerodynamic parameters.

Clark, L. T.↗
NASA NTRS1976

Wall-wake velocity profile for compressible nonadiabatic flows

The paper suggests a new form of the wall-wake profile which is applicable to flows with heat transfer, and for which the velocity gradient at the boundary-layer edge is zero. The modified profile - which takes into account the effect of turbulent Prandtl number - is found to provide a good representation of experimental data for a wide range of Mach numbers and heat transfer. The skin friction coefficient values determined by a least squares fit of the profile to the data are in good agreement with values measured by the floating element technique. The values of boundary-layer thickness determined by the fit correspond more closely to the outer edge of the viscous flow region than those obtained with earlier versions of the wall-wake profile.

Sun, C.-C.↗
NASA NTRS1976

Acoustic liner optimum impedance for spinning modes with mode cut-off ratio as the design criterion

The theoretical optimum acoustic impedance for higher order spinning modes was studied in cylindrical ducts with a boundary layer at the outer edge of a uniform flow. All of the propagating modes were considered from highly propagating to nearly cut-off. It was observed that the mode cut-off ratio uniquely determined the optimum wall impedance and maximum possible attenuation for a given boundary layer thickness, Mach number and frequency. The implications of this phenomenon are quite important in noise suppressor design. Instead of the acoustic power distribution among all of the propagating modes, only the power distribution as a function of cut-off ratio needs to be known. Also, the far field radiation pattern is a function of modal cut-off ratio, and much needed information for liner design can be obtained from these more easily obtained data.

Rice, E. J.↗
NASA NTRS1976

A study of a plume induced separation shock wave, including effects of periodic plume unsteadiness

A wind tunnel investigation was conducted to study the flow field in which separation is caused by an expanding plume, with emphasis on effects associated with periodic unsteadiness in the plume. The separation shock was photographed with high speed motion pictures, from which mean shock position and excursion data were reported. Pressure fluctuations were measured beneath the separation shock. A response of the separation shock to plume periodic unsteadiness was identified, and the magnitude of a corresponding transfer function was defined. Small harmonic effects in plume response to periodic unsteadiness were noted. The stabilizing effect of a lateral surface protuberance near the separation shock wave was investigated. The protuberance configuration was a lateral circular cylinder, and various diameters, all less than the boundary layer thickness, were employed.

Doughty, J. O.↗
NASA NTRS1978

Flow visualization of film cooling with spanwise injection from a small array of holes and compound-angle injection from a large array

Film injection from discrete holes in a smooth, flat plate was studied for two configurations: (1) spanwise injection through a four hole staggered array; and (2) compound angle injection through a 49 hole staggered array. The ratio of boundary layer thicknesses to hole diameter and the Reynolds number were typical of gas turbine film cooling applications. Streaklines showing the motion of the injected air were obtained by photographing small, neutrally buoyant, helium-filled soap bubbles that followed the flow field.

Russell, L. M.↗