SEARCH · Search NASA

Results for “CONTROLS, SERVO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Control systems of the large millimeter telescope

The paper presents the analysis results (in terms of settling time, bandwidth, and servo error in wind disturbances) of four control systems designed for the Large Millimeter Telescope (LMT). The first system, called PI’, consists of the proportional and integral (PI) controllers in the rate and position loops, and is widely used in the antenna and radiotelescope industry. The analysis shows that the PP control system performance is remarkably good when compared to similar control systems applied to typical antennas. This performance is achieved because the LMT structure is exceptionally rigid, however, it does not meet the stringent LMT pointing requirements. The second system, called PL, consists of the PI controller in the rate loop, and the Linear-Quadratic-Gaussian (LQG) controller in the position loop. This type of controller is implemented in the NASA Deep Space Network antennas, where pointing accuracy is twice that of PP control system. The third system, called LP, consists of the LQG controller in the rate loop, and the propositional-integral-derivative (PID) controller in the position loop. This type of loop has not been yet implemented at known antennas or radiotelescopes, but the analysis shows that its pointing accuracy is the ten times better than PP control system. The fourth system, called LL, consists of the LQG controller in both the rate loop, and the position loop. It is the best of the four, with accuracy 250 better than the PP system, thus is worth further investigations, to identify implementation challenges for the telescopes of high pointing requirements.

Souccar, Kainal↗

NASA NTRS1966

Quick-response servo amplifies small hydraulic pressure differences

Hydraulic servo, which quickly diverts fluid to either of two actuators, controls the flow rates and pressures within a hydraulic system so that the output force of the servo system is independent of the velocity of the mechanism which the system actuates. This servo is a dynamic feedback control device.

Wiegard, D. E.↗

NASA NTRS1980

A microprocessor application to a strapdown laser gyro navigator

The replacement of analog circuit control loops for laser gyros (path length control, cross axis temperature compensation loops, dither servo and current regulators) with digital filters residing in microcomputers is addressed. In addition to the control loops, a discussion is given on applying the microprocessor hardware to compensation for coning and skulling motion where simple algorithms are processed at high speeds to compensate component output data (digital pulses) for linear and angular vibration motions. Highlights are given on the methodology and system approaches used in replacing differential equations describing the analog system in terms of the mechanized difference equations of the microprocessor. Standard one for one frequency domain techniques are employed in replacing analog transfer functions by their transform counterparts. Direct digital design techniques are also discussed along with their associated benefits. Time and memory loading analyses are also summarized, as well as signal and microprocessor architecture. Trade offs in algorithm, mechanization, time/memory loading, accuracy, and microprocessor architecture are also given.

Giardina, C.↗

NASA NTRS2018

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗

NASA NTRS1974

Dynamic Docking Test System (DDTS) active table computer program NASA Advanced Docking System (NADS)

A computer program was developed to describe the three-dimensional motion of the Dynamic Docking Test System active table. The input consists of inertia and geometry data, actuator structural data, forcing function data, hydraulics data, servo electronics data, and integration control data. The output consists of table responses, actuator bending responses, and actuator responses.

Gates, R. M.↗

NASA NTRS1977

Load control system

The load control system developed for the shuttle external structural tests is described. The system consists of a load programming/display module, and a load control module along with the following hydraulic system components: servo valves, dump valves, hydraulic system components, and servo valve manifold blocks. One load programming/display subsystem can support multiple load control subsystem modules.

Grosse, J. C.↗

NASA NTRS1992

Task definition, decoupling and redundancy resolution by nonlinear feedback in multi-robot object handling

The problem of rigid object handling by multiple robot arms is investigated. The primary goal is to make the object exhibit a prescribed behavior while in contact with a fully known environment. Point contacts are assumed between the object and the arms. The aspect of task definition to achieve decoupling and linearizing control laws is discussed. Control laws are first formulated at the object level to provide decoupled force and position servo loops. It is then used to form control laws for the individual arms. Redundancies exist at the object and arm levels. The object level redundancy is used to achieve secondary goals in object handling. The arm level redundancies are the zero dynamics and can be controlled by redundant inputs. Full use of the available inputs are used to control the system as a whole. Numerical simulations for a dual-arm situation illustrate the validity of the approach.

Ramadorai, A. K.↗

NASA NTRS1990

Reliability analysis in intelligent machines

Given an explicit task to be executed, an intelligent machine must be able to find the probability of success, or reliability, of alternative control and sensing strategies. By using concepts for information theory and reliability theory, new techniques for finding the reliability corresponding to alternative subsets of control and sensing strategies are proposed such that a desired set of specifications can be satisfied. The analysis is straightforward, provided that a set of Gaussian random state variables is available. An example problem illustrates the technique, and general reliability results are presented for visual servoing with a computed torque-control algorithm. Moreover, the example illustrates the principle of increasing precision with decreasing intelligence at the execution level of an intelligent machine.

Mcinroy, John E.↗

NASA NTRS1995

V/STOL systems research aircraft: A tool for cockpit integration

The next generation ASTOVL aircraft will have a complicated propulsion system. The configuration choices include Direct Lift, Lift-Fan and Lift + Lift/Cruise but the aircraft must also have supersonic performance and low-observable characteristics. The propulsion system may have features such as flow blockers, vectoring nozzles and flow transfer schemes. The flight control system will necessarily fully integrate the aerodynamic surfaces and the propulsive elements. With a fully integrated, fly-by-wire flight/propulsion control system, the options for cockpit integration are interesting and varied. It is possible to de-couple longitudinal and vertical responses allowing the pilot to close the loop on flightpath and flightpath acceleration directly. In the hover, the pilot can control the translational rate directly without having to stabilize the inner rate and attitude loops. The benefit of this approach, reduced workload and increased precision, has previously been demonstrated through several motion-based simulations. In order to prove the results in flight, the V/STOL System Research Aircraft (VSRA) was developed at the NASA Ames Research Center. The VSRA is the YAV-8B Prototype modified with a research flight control system using a series-parallel servo configuration in all the longitudinal degrees of freedom (including thrust and thrust vector angle) to provide an integrated flight and propulsion control system in a limited envelope. Development of the system has been completed and flight evaluations of the response types have been performed. In this paper we will discuss the development of the VSRA, the evolution of the flightpath command and translational rate command response types and the Guest Pilot evaluations of the system. Pilot evaluation results are used to draw conclusions regarding the suitability of the system to satisfy V/STOL requirements.

Stortz, Michael W.↗

NASA NTRS1995

V/STOL Systems Research Aircraft: A Tool for Cockpit Integration

The next generation ASTOVL aircraft will have a complicated propulsion System. The configuration choices include Direct Lift, Lift-Fan and Lift+Lift /Cruise but the aircraft must also have supersonic performance and low-observable characteristics. The propulsion system may have features such as flow blockers, vectoring nozzles and flow transfer schemes. The flight control system will necessarily fully integrate the aerodynamic surfaces and the propulsive elements. With a fully integrated, fly-by-wire flight/propulsion control system, the options for cockpit integration are interesting and varied. It is possible to decouple longitudinal and vertical responses allowing the pilot to close the loop on flight path and flight path acceleration directly. In the hover, the pilot can control the translational rate directly without having to stabilize the inner rate and attitude loops. The benefit of this approach, reduced workload and increased precision. has previously been demonstrated through several motion-based simulations. In order to prove the results in flight, the V/STOL System Research Aircraft (VSRA) was developed at the NASA Ames Research Center. The VSRA is the YAV-8B Prototype modified with a research flight control system using a series-parallel servo configuration in all the longitudinal degrees of freedom (including thrust and thrust vector angle) to provide an integrated flight and propulsion control system in a limited envelope. Development of the system has been completed and flight evaluations of the response types have been performed. In this paper we will discuss the development of the VSRA, the evolution of the flight path command and translational rate command response types and the Guest Pilot evaluations of the system. Pilot evaluation results will be used to draw conclusions regarding the suitability of the system to satisfy V/STOL requirements.

Stortz, Michael W.↗

NASA NTRS1991

Gripper for truss structure assembly

The CIRSSE two-finger gripper is designed to be used with a 6-axis wrist-mounted force-torque sensor as part of an experimental testbed for cooperative robotic manipulation. The gripper system consists of a dedicated controller and a pneumatic powered gripper that is servoed in position or grasping force. The gripper also has a between fingertip light beam sensor. The major features of this new design are: high grasping force to weight ratio (25::1) and compactness (14 cm base-fingertip, 0.8 kilograms); low cost dedicated slave controller; and simple host-controller communications protocol to minimize command interpretation delay. Shared software functions between the host and the controller processor permit the host to select servo mode, servo gain-parameter values, and calibration offsets. Hidden primitive self-test, calibration and servo confidence functions are included.

Kelley, Robert B.↗

NASA NTRSDate not supplied

Design of a Thruster Vector Servo-Elastic Filter

This presents a method to improve the thruster vector servo elasticity (TVSE) stability. TVSE is the coupling between the TVC system engine dynamics and the vehicle flexible modes. It can lead to instability of the flexible modes due to the energy injection from the thrust. For large boosters with heavy TVC engine, TVSE is more likely to cause instability. This instability is part of the plant dynamics and is not detected by the flight control. In this paper, the TVSE is treated as a disturbance rejection problem with the inertial force of the flexible motion viewed as an external disturbance to the TVC actuator control system. By effectively rejecting this disturbance, the engine can be decoupled from the flexible dynamics thus improving TVSE stability. The actuator disturbance transfer function is modified by inserting a TVSE filter into the control system. The filter aims to reduce the magnitude and introduce phase lead of the disturbance transfer function over the TVSE sensitive frequency range while maintaining adequate stability margins of the actuator control system. A prefilter is also designed for good command tracking. The filter and prefilter resulting from this method are usually of low order and can be included to the existing actuator controller if the controller is programmable. This method was demonstrated for a hydraulic Simplex actuator model. Its applications to SLS B1 and B2 TVC actuator are also described. B2 actuator controller is modified based on this method. The tradeoff between TVSE stability and the control system stability can be balanced by adjusting the amount of phase lead introduced by the TVSE filter. This method provides a useful way to solve the TVSE instability issue without costly and time-consuming a TVC system redesign. This method is based on the basic control principles of loop shaping and disturbance rejection and has been proven to be effective under proper circum-stances.

Thrust vector control↗

NASA NTRS1986

Independent Orbiter Assessment (IOA): Analysis of the guidance, navigation, and control subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) is presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The independent analysis results corresponding to the Orbiter Guidance, Navigation, and Control (GNC) Subsystem hardware are documented. The function of the GNC hardware is to respond to guidance, navigation, and control software commands to effect vehicle control and to provide sensor and controller data to GNC software. Some of the GNC hardware for which failure modes analysis was performed includes: hand controllers; Rudder Pedal Transducer Assembly (RPTA); Speed Brake Thrust Controller (SBTC); Inertial Measurement Unit (IMU); Star Tracker (ST); Crew Optical Alignment Site (COAS); Air Data Transducer Assembly (ADTA); Rate Gyro Assemblies; Accelerometer Assembly (AA); Aerosurface Servo Amplifier (ASA); and Ascent Thrust Vector Control (ATVC). The IOA analysis process utilized available GNC hardware drawings, workbooks, specifications, schematics, and systems briefs for defining hardware assemblies, components, and circuits. Each hardware item was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode.

Trahan, W. H.↗

NASA NTRS1985

Adaptation of a modern medium helicopter (Sikorsky S-76) to higher harmonic control

Sikorsky Aircraft has performed analytical studies, design analyses, and risk reduction tests have been performed for Higher Harmonic Control (HHC) on the S-76. The S-76 is an 8 to 10,000 lb helicopter which cruises at 145 kts. Flight test hardware has been assembled, main servo frequency response tested and upgraded, aircraft control system shake tested and verified, open loop controllers designed and fabricated, closed loop controllers defined and evaluated, and rotors turning ground and flight tests planned for the near future. Open loop analysis shows that about 2 deg of higher harmonic feathering at the blade 75% radius will be required to eliminate 4P vibration in the cockpit.

Oleary, J. J.↗

NASA NTRS1986

Nonlinear attitude control of elastic spacecraft-antenna system

An approach to large angle rotational maneuvers of a spacecraft-beam-tip body (an antenna or a reflector) configuration based on nonlinear invertibility and linear feedback stabilization is presented. A control law u sub d is derived to obtain independent decoupled control of attitude angles, lateral elastic deflections, slopes due to bending and angular deflection due to torsion at the tip of the beam using torquers and force actuators. For the stabilization of the elastic oscillations, a linear feedback control law, u sub s, is obtained based on a linearized model about the terminal state augmented with a servo-compensator. Simulation results obtained for single axis control, for simplicity, show that large slewing and elastic mode stabilization can be accomplished in spite of uncertainty in the system using the total control u = u sub d + u sub s.

Singh, S. N.↗

NASA NTRS1990

Field oriented control of induction motors

Induction motors have always been known for their simple rugged construction, but until lately were not suitable for variable speed or servo drives due to the inherent complexity of the controls. With the advent of field oriented control (FOC), however, the induction motor has become an attractive option for these types of drive systems. An FOC system which utilizes the pulse population modulation method to synthesize the motor drive frequencies is examined. This system allows for a variable voltage to frequency ratio and enables the user to have independent control of both the speed and torque of an induction motor. A second generation of the control boards were developed and tested with the next point of focus being the minimization of the size and complexity of these controls. Many options were considered with the best approach being the use of a digital signal processor (DSP) due to its inherent ability to quickly evaluate control algorithms. The present test results of the system and the status of the optimization process using a DSP are discussed.

Burrows, Linda M.↗

NASA NTRS1990

Field oriented control of induction motors

Burrows, Linda M.↗

NASA NTRS1970

Fluidic power control systems

Pneumatic and hydraulic fluidic power control systems, discussing moving part position servos and cold gas reaction systems

Rose, R. K.↗