Results for “CRM” — Page 15

NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply for a microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common Research Model (CRM-HL). An air supply system involving bleed air from the airplane’s auxiliary power unit (APU) plus ram air provides the air to the microjets. A model based on the 1D compressible flow equations is applied to analyze the air supply system configuration and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that APU air can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗

NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply fora microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common ResearchModel (CRM-HL). Two different architectures to supply the air for the microjets are considered: (1) bleed air from the airplane’s auxiliary power unit (APU) plus ram air, and (2) engine fan bleed air plus ram air. A model based on the 1D compressible flow equations is applied to analyze the air supply system architectures and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that pressurized air from the APU or the engine fan can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗

NASA NTRSDate not supplied

Aeropropulsive Assessment of a BLI Tail-Cone Thruster Propulsion System for the NASA Common Research Model and a Transonic Truss-Braced Wing Configuration

This paper presents an investigation into the potential benefits of a boundary layer ingestion(BLI) aft fuselage propulsion system, or tail-cone thruster (TCT), when applied to two transport category aircraft: a conventional tube-and-wing configuration based on the NASA Common Research Model (CRM) and a transonic truss-braced wing (TTBW) configuration. Through the ingestion of low-momentum flow developed over the airframe of an aircraft, the TCT propulsion system technology can reduce overall power consumption and hence fuel burn and emissions. However, an accurate assessment of this potential requires the application of high-fidelity analysis tools that can capture the relevant propulsion-airframe integration effects, at least to first order. Toward this end, the present study employs aeropropulsive analysis tools based on the Reynolds-averaged Navier-Stokes equations to estimate the power savings coefficient, measured relative to equivalent non-BLI configurations of a given airframe. Results indicate shaft power savings of 4.1% and 5.9% can be obtained for the boundary-layer ingesting TCT configuration of the CRM and TTBW, respectively. The present study also examines the coupling between airframe aerodynamics and the inlet flow distortion experienced by the TCT of a given aircraft configuration through airframe component sensitivity studies.

AATT↗

NASA NTRSDate not supplied

NASA Contributions to the High Lift Common Research Model Ecosystem

As part of the High Lift Common Research Model (CRM-HL) ecosystem, NASA has designed and built two CRM-HL models. The first model is a 5.2% scale semispan model that has been tested in the NASA Langley 14- by 22-Foot Subsonic Wind Tunnel (14x22), the low-speed wind tunnel DNW-NWB in Germany and in the National Transonic Facility (NTF) at NASA Langley Research Center. Information on the NASA tests that will include model details, test methods and some test data will be presented in the final document. The second model is a 2.7% scale model that will also be tested in the NTF in both full span and semispan configurations. Information on the design and fabrication of this model will be included in the final document.

Melissa Rivers↗

NASA NTRSDate not supplied

USM3D-ME Contributions to the 5th AIAA High Lift Prediction Workshop

This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by NASA’s flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data Simulations for Cases 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in a relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing URANS simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.

CFD↗

NASA NTRSDate not supplied

USM3D-ME Contributions to the 5th AIAA High Lift Prediction Workshop

This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by the NASA flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data. Simulations for Case 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing unsteady RANS (URANS) simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.

Aerodynamics↗

NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗

NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗

NASA NTRS2018

Distributed-Flap Layout Trade Study on a Highly Flexible Common Research Model

The results of a layout trade study of a full-span, trailing-edge flap system for the NASACommon Research Model (CRM) are presented. Previously developed analysis and design tools areused to determine the potential performance benefits of several flap layouts on a highlyflexible version of the aircraft wing. The wing is first re-twisted for optimal aerodynamicperformance at the design cruise condition while addressing aeroelastic effects. Several flaplayouts are then installed on the new baseline wing. The deflection of each segment on allflap layouts is then optimized for aerodynamic performance at an overspeed flight conditionto ascertain the effectiveness of each flap system. The results indicate that employing two-segmentflaps greatly improves overspeed performance as compared to using no or justsingle-segment flaps. The study also showed that additional segments offer only incrementalimprovements in performance. The results also show that using only four spanwise flaps canproduce meaningful performance gains. Overall, the trade study results suggest a simpledistributed flap system (four spanwise flaps with two segments each) can reduce the drag ofthe Common Research Model by 13 counts at a Mach number that is 3.5 percent higher than thedesign cruise point.

Common Research Model (CRM)↗

NASA NTRSDate not supplied

Numerical Simulation of An Aspect Ratio 13.5 Common Research Model with Trailing Edge Mini-Flaps

This paper presents an aeroelastic modeling study of an aspect ratio 13.5 wind tunnel scale Common Research Model (CRM) with trailing edge mini-flaps. FUN3D is used for the aeroelastic steady and unsteady simulations at Mach 0.85 and dynamic pressure 230 psf. The aeroelastic simulation results are compared with the in-house developed VSPAERO aeroelastic model results. The incremental aerodynamic coefficients predicted by FUN3D and VSPAERO are close except when the mini-flap deflection angle is 10˚. The control reversal behavior is observed for the wing tip mini-flap. A series of dynamic pressure sweep simulations are performed to determine the control reversal onset point. Unsteady simulation results show that there is no buffet phenomenon observed at angle of attacks 0˚ and 2˚ when the mini-flap is deflected 10˚. The mini-flap oscillation simulations show the nonlinear behavior appears when the deflection angle is about 4˚.

Mini-flap↗

NASA NTRSDate not supplied

Aeroelastic Simulation of Wind Tunnel Scale Aspect Ratio 13.5 Common Research Model with Trailing Edge Mini-Flaps

This paper presents a computation study of an aspect ratio 13.5 wind tunnel scale Common Research Model (CRM) with trailing edge mini-flaps using FUN3D. The aeroelastic simulations are conducted under free-air and inside wind tunnel conditions. The NASA Langley Research Center Transonic Dynamic Tunnel (TDT) is a closed circuit and slotted-test-section with a 16 ft ×16 ft test section. The structure mode shapes are extracted from the latest updated NASTRAN Finite-Element Model (FEM) model. A dynamic pressure sweep is performed to determine the control reversal boundary of the trailing edge mini-flaps. The wind tunnel wall interference effects on the mini-flap control derivatives are analyzed based on the simulations.

Aeroelastic↗

NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗

NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗

NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗

NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗

NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗

NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗

DOE OSTI2025

230Th/234U radiochronometry for uranium materials by alpha spectrometry for nuclear forensics analysis

We have developed an alpha spectrometry method for 230Th/234U radiochronometry to determine the model separation age for uranium materials. This method offers an alternative to the more commonly used, but significantly more resource intensive multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) while providing similar accuracy and precision. The development included radiochemical separation of uranium and thorium, calibration of the 232U tracer and the alpha spectrometry measurement. The method was validated by analyzing a certified reference material, CRM 125-A, which is a uranium oxide pellet assay, isotopic, and radiochronometric standard. The results were compared to those obtained by our routine MC-ICP-MS 230Th/234U radiochronometry analysis method to assess the performance parameters for alpha spectrometry compared to the state-of-the-art technique.

Macsik, Zsuzsanna [Los Alamos National Laboratory ↗