Search NASA⌕ Search

SEARCH · Search NASA

Results for “CUTTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Flume and single-pass washing systems for fresh-cut produce processing: Disinfection by-products evaluation

Free chlorine is widely used in fresh-cut produce washing to minimize microbial cross-contamination, but its application can also lead to the formation of harmful disinfection byproducts (DBPs). This study compared DBPs in process water and washed produce during commercial operation. Samples of shredded lettuce and diced cabbages washed in chlorinated water in the traditional double-flume wash and novel immersion-free single-pass wash systems were collected at multiple time points and locations from the processing lines. A suite of 33 conventional and emerging DBPs, including 4 trihalomethanes (THMs), 9 haloacetic acids (HAAs), 9 nitrogenous DBPs (N-DBPs), and 11 carbonaceous DBPs (C-DBPs), were investigated. Overall, N-DBPs and HAAs dominated the concentration of detected DBPs. Wash water in the flumes contained 7–111 folds higher DBP levels compared to that in the single-pass system, with the abundance of DBPs following the order of N-DBPs > HAAs > C-DBPs > THMs. DBPs were detected on washed produce, presenting primarily in the forms of N-DBPs and HAAs followed by C-DBPs and THMs. While higher levels of DBPs were detected in flume-washed produce, the final potable water rinse significantly reduced the DBP concentration in these products. The concentrations of THMs and HAAs on these washed products were used to estimate potential exposure via consumption of fresh-cut produce and the levels were below the daily allowable exposure for drinking water standard established by the U.S. Environmental Protection Agency. The detected high concentration and potential toxicity of N-DBPs indicate the need for further research. Here, the findings of this study advance the understanding of the formation and removal of DBPs during wash processes, and identify additional research opportunities for further reduction in DBPs and food safety improvement.

59 BASIC BIOLOGICAL SCIENCES↗

Short-cut Methods versus Rigorous Methods for Performance-evaluation of Distillation Configurations

Here, this study demonstrates the efficacy of a short-cut method such as the Global Minimization Algorithm (GMA), that uses assumptions of ideal mixtures, constant molar overflow (CMO) and pinched columns, in pruning the search-space of distillation column configurations for zeotropic multicomponent separation, to provide a small subset of attractive configurations with low minimum heat duties. The short-cut method, due to its simplifying assumptions, is computationally efficient, yet reliable in identifying the small subset of useful configurations for further detailed process evaluation. This two-tier approach allows expedient search of the configuration space containing hundreds to thousands of candidate configurations for a given application.

42 ENGINEERING↗

Investigation of Ti6Al4V Orthogonal Cutting Numerical Simulations using Different Material Models

Titanium alloys are materials considered as extremely difficult to cut and titanium alloy Ti6Al4V is a reference in machining of titanium. The segmented (saw toothed) chip morphology has attracted great interest in researchers because the understanding of the saw-toothed chip morphology helps to understand the chip formation mechanisms. In this study, the effect of different constitutive models on the saw-toothed chip morphology is examined in machining Ti6Al4V. The paper presents the influence of eight material constitutive modelling in the simulation of segmented chip formation. A critical comparison of outstanding process outputs as cutting force, temperature and measurable parameters for segmented chips is carried out to compare and discuss the performance of the eight different material models to each other and with experimental data.

36 MATERIALS SCIENCE↗

The Effect of Cutting Speed in Metallic Glass Grinding

In this paper, the effects of the cutting speed in metallic glass grinding were investigated in dry conditions. The results showed that grinding forces decrease as grinding energy increase with the increasing cutting speeds. The present investigations on ground surface and grinding chips morphologies -shows that material removal and surface formation of the BMG are mainly due to the ductile chip deformation and ploughing as well as brittle fracture of some particles from the edges of the tracks. The roughness values obtained with the Cubic Boron Nitride wheels are acceptable for the grinding operation.

36 MATERIALS SCIENCE↗

Laser Cutting and Micromachining for Localized and Targeted Solar Cell Characterization

Laser cutting and micromachining can be applied to solar cell materials for processing and characterization applications. An ultrashort pulse (USP) laser with sub-picosecond pulse width can remove material with minimal thermal effects or damage, which is termed `cold ablation'. Such USP laser cutting and scribing can be implemented for isolating areas within a larger cell while maintaining electrical performance and preventing laser-induced damage and shunting. Laser micromachining has been used to isolate a shunt to improve cell performance and to isolate a small, selected area to define a sample suitable for deep level transient spectroscopy.

14 SOLAR ENERGY↗

Ease of cutting of high-chromium ferrite steels

The ease of cutting of high-chromium ferrite steels is considered. In cutting, the productivity is found to be satisfactory, but it is difficult to obtain a machined surface of acceptable quality. Recommendations are made for improving the quality of the machined surface.

42 ENGINEERING↗

Theory of Intermittent Cutting. 3. Description of Tool Exit from the Blank

Vorontsov’s plastic-flow method permits the derivation of a model of cutting for the region where the tool exits the blank. The stress–strain state of the blank is determined, and the dimensions of the plastic-deformation zone are calculated. The main cutting parameters are shown to be variable.

42 ENGINEERING↗

Determining the Mean Frictional Coefficient in Metal Cutting

An analytical formula is derived for determining the frictional coefficient at cutter–blank contact, on the basis of the cutting equations and the shear angle, and is verified by means of experimental data. This formula may be used to calculate the cutting parameters, without constraints on the significant factors.

42 ENGINEERING↗

Theory of Intermittent Cutting. 5. Description of Tool Entry in the Blank

Vorontsov’s plastic-flow method permits the derivation of a model of cutting for the region where the tool enters the blank. The stress–strain state of the blank is determined, and the dimensions of the plasticdeformation zone are calculated. The main cutting parameters are shown to be variable.

42 ENGINEERING↗

Control of the Machining Precision in Thread Cutting

In research on thread cutting, the flaws inevitably arising in the first two and last two turns of the thread, when the process is unsteady, are analyzed. Specifically, insertion and removal of the tool from the workpiece are accompanied by abrupt change in thread diameter: abrupt decrease in the case of threads on shafts; and increase for threads in holes. That leads to the appearance of slots on assembly, thereby increasing the likelihood of accidents and other problems in thread operation. A method of eliminating such gaps is proposed and tested: control of the machining precision in the course of thread cutting. In particular, the thread diameter and pitch are controlled by compensation of the axial and radial elastic displacements of the tool, based on timely correction of the transverse and longitudinal supply during the unsteady stage of the process. Compensation of the machining errors improves the dimensional precision of the thread and decreases the systematic errors and spread in the thread dimensions.

42 ENGINEERING↗

Eigenfrequency-Based Prediction of the Cutting Properties of Superhard Inserts

The relation between the cutting properties of superhard tool inserts and their eigenfrequency is studied. The relation between the life of inserts and their acoustic properties is confirmed experimentally in the turning of high-temperature nickel alloys and quenched steels. A method is developed for determining the eigenfrequency of cutting inserts, along with the corresponding equipment.

36 MATERIALS SCIENCE↗

Evolution of the Dynamic Cutting System with Irreversible Energy Transformation in the Machining Zone

The evolution of the dynamic cutting system is simulated with different trajectories of the power of irreversible transformations in performing work. The evolutionary changes associated with change in tool wear and in surface precision and quality depend on the dynamic properties, on the subsystems that interact through cutting, and also on the initial dynamic relationship formed by the process.

42 ENGINEERING↗

Stability Evaluation for a Damped, Constrained-Motion Cutting Force Dynamometer

This paper describes the dynamic stability evaluation of a constrained-motion dynamometer (CMD) with passive damping. The CMD’s flexure-based design offers an alternative to traditional piezoelectric cutting force dynamometers, which can exhibit adverse effects of the complex structural dynamics on the measurement accuracy. In contrast, the CMD system’s structural dynamics are nominally single degree of freedom and are conveniently altered by material selection, flexure element geometry, and element arrangement. In this research, a passive damping approach is applied to increase the viscous damping ratio and, subsequently, the stability limit. Cutting tests were completed and the in situ CMD displacement and velocity signals were sampled at the spindle rotating frequency. The periodic sampling approach was used to determine if the milling response was synchronous with the spindle rotation (stable) or not (chatter) by constructing Poincaré maps for both experiment and prediction (time-domain simulation). It was found that the viscous damping coefficient was increased by 130% and the critical stability limit was increased from 4.3 mm (no damping) to 15.4 mm (with damping).

36 MATERIALS SCIENCE↗