SEARCH · Search NASA

Results for “Cloud Implementation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS2018

CALIPSO Lidar Calibration at 532 nm: Version 4 Nighttime Algorithm

Data products from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) were recently updated following the implementation of new (version 4) calibration algorithms for all of the level 1 attenuated backscatter measurements. In this work we present the motivation for and the implementation of the version 4 nighttime 532 nm parallel channel calibration. The nighttime 532 nm calibration is the most fundamental calibration of CALIOP data, since all of CALIOP’s other radiometric calibration procedures – i.e., the 532 nm daytime calibration and the 1064 nm calibrations during both nighttime and daytime – depend either directly or indirectly on the 532 nm nighttime calibration. The accuracy of the 532 nm nighttime calibration has been significantly improved by raising the molecular normalization altitude from 30-34 km to 36-39 km to substantially reduce stratospheric aerosol contamination. Due to the greatly reduced molecular number density and consequently reduced signal-to-noise ratio (SNR) at these higher altitudes, the signal is now averaged over a larger number of samples using data from multiple adjacent granules. As well, an enhanced strategy for filtering the radiation-induced noise from high energy particles was adopted. Further, the meteorological model used in the earlier versions has been replaced by the improved MERRA-2 model. An aerosol scattering ratio of 1.01 ± 0.01 is now explicitly used for the calibration altitude. These modifications lead to globally revised calibration coefficients which are, on average, 2-3% lower than in previous data releases. Further, the new calibration procedure is shown to eliminate biases at high altitudes that were present in earlier versions and consequently leads to an improved representation of stratospheric aerosols. Validation results using airborne lidar measurements are also presented. Biases relative to collocated measurements acquired by the Langley Research Center (LaRC) airborne high spectral resolution lidar (HSRL) are reduced from 3.6% ± 2.2% in the version 3 data set to 1.6% ± 2.4 % in the version 4 release.

Jayanta Kar↗

NASA NTRS2018

The New (Version 4) Calibration of the Nighttime 532nm Channel of the CALIPSO Lidar

The data products from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on board Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) were recently updated following the implementation of a new (version 4.1) calibration algorithm for all the level 1 products. We present the motivation for and the implementation of the version 4.1 nighttime 532 nm parallel channel measurements. This is the most fundamental calibration of CALIOP data since all other measurements, i.e the 532 nm nighttime perpendicular, daytime 532 nm as well as 1064 nm are tied to this calibration. The new calibration is shown to resolve the discrepancies in the earlier version and also leads to an improved representation of the stratospheric aerosols. Initial validation results using ground based and airborne lidar measurements are also presented.

Kar, J.↗

NASA NTRS2017

Cumulus: NASA's Cloud Based Distributed Active Archive Center Prototype

NASAs Earth Science Data System (ESDS) Program serves as a central cog in order to facilitate the implementation of NASA's Earth Science strategic plan. Since 1994, the ESDS Program has committed to the full and open sharing of Earth science data obtained from NASA instruments to all users. One of the key responsibilities of the ESDS Program is to continuously evolve the entire data and information system to maximize returns on the collected NASA data. An independent review was conducted in 2015 to holistically review the EOSDIS in order to identify gaps. The review recommendations were to investigate two areas: one, whether commercial cloud providers offer potential for storage, processing, and operational efficiencies, and two, the potential development of new data access and analysis paradigms. In response, ESDS has initiated several prototypes investigating the advantages and risks of leveraging cloud computing. This paper describes one such prototyping activity named Cumulus. Cumulus is being designed and developed as a "native" cloud-based data ingest, archive and management system that can be used for all future NASA Earth science data streams. Cumulus will foster design of new analysisvisualization tools that can leverage collocated data from all of the distributed DAACs as well as elastic cloud computing resources.

Earth Science Informatics↗

NASA NTRS1996

Cloud identification using genetic algorithms and massively parallel computation

As a Guest Computational Investigator under the NASA administered component of the High Performance Computing and Communication Program, we implemented a massively parallel genetic algorithm on the MasPar SIMD computer. Experiments were conducted using Earth Science data in the domains of meteorology and oceanography. Results obtained in these domains are competitive with, and in most cases better than, similar problems solved using other methods. In the meteorological domain, we chose to identify clouds using AVHRR spectral data. Four cloud speciations were used although most researchers settle for three. Results were remarkedly consistent across all tests (91% accuracy). Refinements of this method may lead to more timely and complete information for Global Circulation Models (GCMS) that are prevalent in weather forecasting and global environment studies. In the oceanographic domain, we chose to identify ocean currents from a spectrometer having similar characteristics to AVHRR. Here the results were mixed (60% to 80% accuracy). Given that one is willing to run the experiment several times (say 10), then it is acceptable to claim the higher accuracy rating. This problem has never been successfully automated. Therefore, these results are encouraging even though less impressive than the cloud experiment. Successful conclusion of an automated ocean current detection system would impact coastal fishing, naval tactics, and the study of micro-climates. Finally we contributed to the basic knowledge of GA (genetic algorithm) behavior in parallel environments. We developed better knowledge of the use of subpopulations in the context of shared breeding pools and the migration of individuals. Rigorous experiments were conducted based on quantifiable performance criteria. While much of the work confirmed current wisdom, for the first time we were able to submit conclusive evidence. The software developed under this grant was placed in the public domain. An extensive user's manual was written and distributed nationwide to scientists whose work might benefit from its availability. Several papers, including two journal articles, were produced.

Buckles, Bill P.↗

DOE OSTI2024

Suppressed Cosmic-Ray Energy Densities in Molecular Clouds from Streaming Instability-regulated Transport

Abstract Cosmic rays (CRs) are the primary driver of ionization in star-forming molecular clouds (MCs). Despite their potential impacts on gas dynamics and chemistry, no simulations of star cluster formation following the creation of individual stars have included explicit cosmic-ray transport (CRT) to date. We conduct the first numerical simulations following the collapse of a 2000 M ⊙ MC and the subsequent star formation including CRT using the STAR FORmation in Gaseous Environments framework implemented in the GIZMO code. We show that when CRT is streaming-dominated, the CR energy in the cloud is strongly attenuated due to energy losses from the streaming instability. Consequently, in a Milky Way–like environment the median CR ionization rate in the cloud is low ( ζ ≲ 2 × 10 −19 s −1 ) during the main star-forming epoch of the calculation and the impact of CRs on the star formation in the cloud is limited. However, in high-CR environments, the CR distribution in the cloud is elevated ( ζ ≲ 6 × 10 −18 ), and the relatively higher CR pressure outside the cloud causes slightly earlier cloud collapse and increases the star formation efficiency by 50% to ∼13%. The initial mass function is similar in all cases except with possible variations in a high-CR environment. Further studies are needed to explain the range of ionization rates observed in MCs and explore star formation in extreme CR environments.

Astronomy & Astrophysics↗

NASA NTRSDate not supplied

Use NASA Earthdata in the Cloud

With the impending arrival of new, high-data-volume Earth observation missions, NASA’s ability to effectively ingest, process, and archive large amounts of data requires the most cost-effective, flexible, and scalable data-management architectures and technologies. To meet these demands, NASA's Earth Science Data Systems (ESDS) Program is implementing a strategic vision to develop and operate multiple components of NASA's Earth Observing System Data and Information System (EOSDIS) in a commercial cloud environment. As more earth observing data is moved into the cloud, NASA EOSDIS wants to share our reasoning for moving data into the commercial cloud, as well as demonstrate how end-users can take advantage of both data in the cloud and cloud-deployed services. This presentation explains the enterprise reasons for moving data into the cloud, specifically the scalability of cloud systems, the flexibility to pivot to the most optimal language/system/architecture, and the reduced redundancy of a common architecture. Then we primarily focus on the user-driven reasons for moving to the cloud. Equal access to high performance computing helps all parties, especially users that don't have access to their own on-premise computing infrastructure. Rapid deployment allows users to spin up their own systems without needing the extensive platform previously required for large scale development. Cost effectiveness allows users a wide breadth of computing options, from super computer ability to small scale development, which can help underserved communities. Finally we link to internal resources that users can utilize to begin their cloud based development journey without having to be an expert in the field.

Nicholas Doty↗

NASA NTRS2006

Simulated convective systems using a cloud resolving model: Impact of large-scale temperature and moisture forcing using observations and GEOS-3 reanalysis

The GCE (Goddard Cumulus Ensemble) model, which has been developed and improved at NASA Goddard Space Flight Center over the past two decades, is considered as one of the finer and state-of-the-art CRMs (Cloud Resolving Models) in the research community. As the chosen CRM for a NASA Interdisciplinary Science (IDS) Project, GCE has recently been successfully upgraded into an MPI (Message Passing Interface) version with which great improvement has been achieved in computational efficiency, scalability, and portability. By basically using the large-scale temperature and moisture advective forcing, as well as the temperature, water vapor and wind fields obtained from TRMM (Tropical Rainfall Measuring Mission) field experiments such as SCSMEX (South China Sea Monsoon Experiment) and KWAJEX (Kwajalein Experiment), our recent 2-D and 3-D GCE simulations were able to capture detailed convective systems typical of the targeted (simulated) regions. The GEOS-3 [Goddard EOS (Earth Observing System) Version-3] reanalysis data have also been proposed and successfully implemented for usage in the proposed/performed GCE long-term simulations (i.e., aiming at producing massive simulated cloud data -- Cloud Library) in compensating the scarcity of real field experimental data in both time and space (location). Preliminary 2-D or 3-D pilot results using GEOS-3 data have generally showed good qualitative agreement (yet some quantitative difference) with the respective numerical results using the SCSMEX observations. The first objective of this paper is to ensure the GEOS-3 data quality by comparing the model results obtained from several pairs of simulations using the real observations and GEOS-3 reanalysis data. The different large-scale advective forcing obtained from these two kinds of resources (i.e., sounding observations and GEOS-3 reanalysis) has been considered as a major critical factor in producing various model results. The second objective of this paper is therefore to investigate and present such an impact of large-scale forcing on various modeled quantities (such as hydrometeors, rainfall, and etc.). A third objective is to validate the overall GCE 3-D model performance by comparing the numerical results with sounding observations, as well as available satellite retrievals.

Shie, C.-L.↗

NASA NTRS1979

Infrared radiometer for the Pioneer Venus orbiter. I - Instrument description

A ten-channel IR radiometer for the Pioneer Venus orbiter is described. The experimental techniques used and the design of the instrumentation by which they were implemented are considered. Emphasis is placed on temperature sounding, limb sounding, limb darkening, zenith scanning, cloud top temperature, spectral albedo and water vapor measurements. Instrumentation description is also given including optics, detectors, and electronics. Attention is given to data acquisition and handling, calibration, and in-flight performance.

Taylor, F. W.↗

NASA NTRS1997

Development, Validation, and Potential Enhancements to the Second-Generation Operational Aerosol Product at the National Environmental Satellite, Data, and Information Service of the National Oceanic and Atmospheric Administration

A revised (phase 2) single-channel algorithm for aerosol optical thickness, tau(sup A)(sub SAT), retrieval over oceans from radiances in channel 1 (0.63 microns) of the Advanced Very High Resolution Radiometer (AVHRR) has been implemented at the National Oceanic and Atmospheric Administration's National Environmental Satellite Data and Information Service for the NOAA 14 satellite launched December 30, 1994. It is based on careful validation of its operational predecessor (phase 1 algorithm), implemented for NOAA 14 in 1989. Both algorithms scale the upward satellite radiances in cloud-free conditions to aerosol optical thickness using an updated radiative transfer model of the ocean and atmosphere. Application of the phase 2 algorithm to three matchup Sun-photometer and satellite data sets, one with NOAA 9 in 1988 and two with NOAA 11 in 1989 and 1991, respectively, show systematic error is less than 10%, with a random error of sigma(sub tau) approx. equal 0.04. First results of tau(sup A)(sub SAT) retrievals from NOAA 14 using the phase 2 algorithm, and from checking its internal consistency, are presented. The potential two-channel (phase 3) algorithm for the retrieval of an aerosol size parameter, such as the Junge size distribution exponent, by adding either channel 2 (0.83 microns) from the current AVHRR instrument, or a 1.6-microns channel to be available on the Tropical Rainfall Measurement Mission and the NOAA-KLM satellites by 1997 is under investigation. The possibility of using this additional information in the retrieval of a more accurate estimate of aerosol optical thickness is being explored.

Stowe, Larry L.↗

NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap joint method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a comprehensive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗

NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap join method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a compressive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗

DOE OSTI2024

Electronic structure simulations in the cloud computing environment

The transformative impact of modern computational paradigms and technologies, such as high-performance computing, quantum computing, and cloud computing, has opened up profound new opportunities for scientific simulations. Scalable computational chemistry is one beneficiary of this technological progress. The main focus of this paper is on the performance of various quantum chemical formulations, ranging from low-order methods to high-accuracy approaches, implemented in different computational chemistry packages, such as NWChem, NWChemEx, SPEC, ExaChem, and FLOSIC codes on the Azure Quantum Element (AQE) Microsoft cloud services. We pay particular attention to the intricate workflows for performing composite chemistry simulations, associated data curation, and mechanisms for accuracy assessment, as defined by the enabling cloud Computational Chemistry as a Service (CCaaS). Our focus also extends to Arrows' automated workflow for high throughput simulations. Finally, we provide a perspective on the role of cloud computing in supporting the mission of leadership computational facilities (LCFs).

computational chemistry, electronic structure, Clo↗

NASA NTRS1991

Lightning mapping system

A Lightning Detection and Ranging (LDAR) System is being implemented at KSC in Florida. The first operational use is expected in the late summer of 1991. The system is designed to map the location of in-cloud and cloud-to-ground lightning based on the time of arrival (TOA) of electromagnetic radiation. The system detects very high frequency (VHF) radiation and designed to map the volumetric extent of lightning. The system implements two independent antenna arrays to provide a fast data quality check, as necessary for a real-time warning system. The system performance goals and a comparison with a similar system implemented in the mid-1970's is made.

Lennon, C.↗

NASA NTRS2014

A Wrf-Chem Flash Rate Parameterization Scheme and LNO(x) Analysis of the 29-30 May 2012 Convective Event in Oklahoma During DC3

The Deep Convective Clouds and Chemistry (DC3) field campaign in 2012 provided a plethora of aircraft and ground-based observations (e.g., trace gases, lightning and radar) to study deep convective storms, their convective transport of trace gases, and associated lightning occurrence and production of nitrogen oxides (NOx). Based on the measurements taken of the 29-30 May 2012 Oklahoma thunderstorm, an analysis against a Weather Research and Forecasting Chemistry (WRF-Chem) model simulation of the same event at 3-km horizontal resolution was performed. One of the main objectives was to include various flash rate parameterization schemes (FRPSs) in the model and identify which scheme(s) best captured the flash rates observed by the National Lightning Detection Network (NLDN) and Oklahoma Lightning Mapping Array (LMA). The comparison indicates how well the schemes predicted the timing, location, and number of lightning flashes. The FRPSs implemented in the model were based on the simulated thunderstorms physical features, such as maximum vertical velocity, cloud top height, and updraft volume. Adjustment factors were added to each FRPS to best capture the observed flash trend and a sensitivity study was performed to compare the range in model-simulated lightning-generated nitrogen oxides (LNOx) generated by each FRPS over the storms lifetime. Based on the best FRPS, model-simulated LNOx was compared against aircraft measured NOx. The trace gas analysis, along with the increased detail in the model specification of the vertical distribution of lightning flashes as suggested by the LMA data, provide guidance in determining the scenario of NO production per intracloud and cloud-to-ground flash that best matches the NOx mixing ratios observed by the aircraft.

Cloud physics↗

NASA NTRS2014

A WRF-Chem Flash Rate Parameterization Scheme and LNOx Analysis of the 29-30 May 2012 Convective Event in Oklahoma During DC3

The Deep Convective Clouds and Chemistry (DC3) field campaign in 2012 provided a plethora of aircraft and ground-based observations (e.g., trace gases, lightning and radar) to study deep convective storms, their convective transport of trace gases, and associated lightning occurrence and production of nitrogen oxides (NOx). Based on the measurements taken of the 29-30 May 2012 Oklahoma thunderstorm, an analysis against a Weather Research and Forecasting Chemistry (WRF-Chem) model simulation of the same event at 3-km horizontal resolution was performed. One of the main objectives was to include various flash rate parameterization schemes (FRPSs) in the model and identify which scheme(s) best captured the flash rates observed by the National Lightning Detection Network (NLDN) and Oklahoma Lightning Mapping Array (LMA). The comparison indicates how well the schemes predicted the timing, location, and number of lightning flashes. The FRPSs implemented in the model were based on the simulated thunderstorms physical features, such as maximum vertical velocity, cloud top height, and updraft volume. Adjustment factors were applied to each FRPS to best capture the observed flash trend and a sensitivity study was performed to compare the range in model-simulated lightning-generated nitrogen oxides (LNOx) generated by each FRPS over the storms lifetime. Based on the best FRPS, model-simulated LNOx was compared against aircraft measured NOx. The trace gas analysis, along with the increased detail in the model specification of the vertical distribution of lightning flashes as suggested by the LMA data, provide guidance in determining the scenario of NO production per intracloud and cloud-to-ground flash that best matches the NOx mixing ratios observed by the aircraft.

Atmospheric chemistry↗

NASA NTRS2008

FPGA Coprocessor for Accelerated Classification of Images

An effort related to that described in the preceding article focuses on developing a spaceborne processing platform for fast and accurate onboard classification of image data, a critical part of modern satellite image processing. The approach again has been to exploit the versatility of recently developed hybrid Virtex-4FX field-programmable gate array (FPGA) to run diverse science applications on embedded processors while taking advantage of the reconfigurable hardware resources of the FPGAs. In this case, the FPGA serves as a coprocessor that implements legacy C-language support-vector-machine (SVM) image-classification algorithms to detect and identify natural phenomena such as flooding, volcanic eruptions, and sea-ice break-up. The FPGA provides hardware acceleration for increased onboard processing capability than previously demonstrated in software. The original C-language program demonstrated on an imaging instrument aboard the Earth Observing-1 (EO-1) satellite implements a linear-kernel SVM algorithm for classifying parts of the images as snow, water, ice, land, or cloud or unclassified. Current onboard processors, such as on EO-1, have limited computing power, extremely limited active storage capability and are no longer considered state-of-the-art. Using commercially available software that translates C-language programs into hardware description language (HDL) files, the legacy C-language program, and two newly formulated programs for a more capable expanded-linear-kernel and a more accurate polynomial-kernel SVM algorithm, have been implemented in the Virtex-4FX FPGA. In tests, the FPGA implementations have exhibited significant speedups over conventional software implementations running on general-purpose hardware.

Pingree, Paula J.↗

DOE OSTI2024

Improving the Freight Productivity of a Heavy-Duty, Battery Electric Truck by Intelligent Energy Management

This project aimed to enhance the range and reduce the operating costs of battery electric Class 8 trucks traveling over 250 miles daily. This was achieved through the development and implementation of an intelligent-Energy Management System (i-EMS) that leverages vehicle and operations data, physics-aware machine learning algorithms, and vehicle-to-cloud (V2C) connectivity. The project hypothesized that advanced machine learning algorithms and real-time data analytics could significantly improve the energy efficiency and range of these trucks. Key objectives included developing a physics-aware machine learning algorithm, implementing an i-EMS with V2C connectivity and physics-aware spatial data analytics (PSDA), and validating the system’s effectiveness with fleet partners HEB Companies and Murphy Logistics. Extensive data collection from vehicle operations, including vehicle characteristics, road conditions, and payload, was conducted. A machine learning algorithm was developed to predict energy consumption and enable proactive decision-making. The i-EMS was implemented on two Volvo VNR BEVs, with operators receiving charging and routing recommendations. Charging stations were installed at depot locations in Texas and Minnesota, with an additional on-route charger in Minnesota. Significant findings included a 14% range improvement for Murphy Logistics on a highway-driving eco-route and a 22% range improvement for HEB Companies on a city-driving eco-route. The i-EMS utilized rule-based methods and physics-based algorithms to predict and reduce energy consumption, with real-time monitoring and analysis through V2C connectivity enabling proactive decision-making. The project demonstrated the feasibility and economic viability of battery electric Class 8 trucks for long-haul operations, showcasing the potential of physics-aware machine learning in optimizing energy management. The successful implementation of the i-EMS in real-world scenarios validates its practical application and effectiveness, paving the way for the widespread adoption of battery electric vehicles in the freight transportation industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS2026

Hydrology Copilot: A Cloud-Native Ai System for Hydrological Data Analysis

The emergence of AI-driven Earth observation systems promises to broaden access to petabyte-scale geospatial data beyond domain specialists. However, translating this vision into operational scientific infrastructure requires addressing fundamental challenges in data virtualization, code transparency, and domain-specific reasoning. We present Hydrology Copilot, a cloud-native AI framework for natural-language-driven analysis of Earth observation data. To demonstrate operational capabilities at scale, we implement the system using NASA's North American Land Data Assimilation System version 3 (NLDAS-3), which provides surface meteorological forcing and land-surface model output across North and Central America at 1-km resolution, from which drought diagnostics are derived. The system integrates five core contributions: (1) scalable data virtualization using Kerchunk-based cloud optimized access, achieving a 1.5 to 4.6 times improvement in I/O latency across benchmark queries spanning regional single-day extractions (4.6 times speedup) to continental monthly aggregations (1.5 times speedup); (2) transparent code generation through Microsoft Azure AI Foundry agents that expose executable Python workflows for scientific verification; (3) persistent conversational memory enabling multi-turn analytical discourse across sessions; (4) intelligent query validation that enforces dataset boundaries and resolves ambiguous requests before execution; and (5) a multi-agent architecture coordinating query parsing, code generation, and visualization. We evaluate the system through drought-monitoring workflows, demonstrating reliable code generation, accurate results validated against reference computations and the operational U.S. Drought Monitor, and efficient operation across increasingly complex tasks. By bridging natural-language interfaces with rigorous hydrological analysis, Hydrology Copilot advances beyond proof-of-concept demonstrations to provide a deployable framework for operational Earth science applications.

Data virtualization↗