Search NASA⌕ Search

SEARCH · Search NASA

Results for “Comparative visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
NASA NTRSDate not supplied

Wind Tunnel Testing of AFC over a Deflected Aileron on the High-Lift Common Research Model

Active flow control (AFC) using discrete fluidic actuators distributed along the span, just upstream of the deflected aileron of the 10% scale high-lift version of the Common Research Model (CRM-HL), was evaluated during a wind tunnel test in the NASA Langley 14- by 22-Foot Subsonic Tunnel. For this set of experiments, a new outboard section was fabricated incorporating a deflectable aileron. Aileron deflection angles of 0, 7.5, 16, and 25 were investigated. This experimental investigation is in response to a recent study by Boeing potential to use AFC with a drooped aileron during takeoff to improve lift-to-drag ratio (L/D) by as much as 5%, depending on AFC mass flow rate. AFC is used at deflection angles above the nominal deflection of 7.5 to control the resulting flow separation that occurs and potentially improve L/D. Improvements in aircraft low-speed L/D can affect vehicle range and/or payload. Tuft flow visualization data, steady and unsteady surface pressure data, and force and moment data are used to compare the flowfields with and without AFC. Parameters varied include actuator momentum coefficient and aileron deflection angle. The surface pressure and tuft flow visualization results indicate that without AFC, the flow over a majority of the aileron upper surface is separated for aileron deflection angles larger than 7.5. When AFC is applied, the flow is reattached to the aileron. Force and moment results show that a local increase in lift leads to an increase in L/D of at least 3.5% using mass flow rates thought to be available from air sources onboard a commercial transport.

AFC↗
NASA NTRS1999

Multitaper Spectral Analysis and Wavelet Denoising Applied to Helioseismic Data

Estimates of solar normal mode frequencies from helioseismic observations can be improved by using Multitaper Spectral Analysis (MTSA) to estimate spectra from the time series, then using wavelet denoising of the log spectra. MTSA leads to a power spectrum estimate with reduced variance and better leakage properties than the conventional periodogram. Under the assumption of stationarity and mild regularity conditions, the log multitaper spectrum has a statistical distribution that is approximately Gaussian, so wavelet denoising is asymptotically an optimal method to reduce the noise in the estimated spectra. We find that a single m-upsilon spectrum benefits greatly from MTSA followed by wavelet denoising, and that wavelet denoising by itself can be used to improve m-averaged spectra. We compare estimates using two different 5-taper estimates (Stepian and sine tapers) and the periodogram estimate, for GONG time series at selected angular degrees l. We compare those three spectra with and without wavelet-denoising, both visually, and in terms of the mode parameters estimated from the pre-processed spectra using the GONG peak-fitting algorithm. The two multitaper estimates give equivalent results. The number of modes fitted well by the GONG algorithm is 20% to 60% larger (depending on l and the temporal frequency) when applied to the multitaper estimates than when applied to the periodogram. The estimated mode parameters (frequency, amplitude and width) are comparable for the three power spectrum estimates, except for modes with very small mode widths (a few frequency bins), where the multitaper spectra broadened the modest compared with the periodogram. We tested the influence of the number of tapers used and found that narrow modes at low n values are broadened to the extent that they can no longer be fit if the number of tapers is too large. For helioseismic time series of this length and temporal resolution, the optimal number of tapers is less than 10.

Komm, R. W.↗
NASA NTRS2003

Data Access Tools And Services At The Goddard Distributed Active Archive Center (GDAAC)

As one of the largest providers of Earth Science data from the Earth Observing System, GDAAC provides the latest data from the Moderate Resolution Imaging Spectroradiometer (MODIS), Atmospheric Infrared Sounder (AIRS), Solar Radiation and Climate Experiment (SORCE) data products via GDAAC's data pool (50TB of disk cache). In order to make this huge volume of data more accessible to the public and science communities, the GDAAC offers multiple data access tools and services: Open Source Project for Network Data Access Protocol (OPeNDAP), Grid Analysis and Display System (GrADS/DODS) (GDS), Live Access Server (LAS), OpenGlS Web Map Server (WMS) and Near Archive Data Mining (NADM). The objective is to assist users in retrieving electronically a smaller, usable portion of data for further analysis. The OPeNDAP server, formerly known as the Distributed Oceanographic Data System (DODS), allows the user to retrieve data without worrying about the data format. OPeNDAP is capable of server-side subsetting of HDF, HDF-EOS, netCDF, JGOFS, ASCII, DSP, FITS and binary data formats. The GrADS/DODS server is capable of serving the same data formats as OPeNDAP. GDS has an additional feature of server-side analysis. Users can analyze the data on the server there by decreasing the computational load on their client's system. The LAS is a flexible server that allows user to graphically visualize data on the fly, to request different file formats and to compare variables from distributed locations. Users of LAS have options to use other available graphics viewers such as IDL, Matlab or GrADS. WMS is based on the OPeNDAP for serving geospatial information. WMS supports OpenGlS protocol to provide data in GIs-friendly formats for analysis and visualization. NADM is another access to the GDAAC's data pool. NADM gives users the capability to use a browser to upload their C, FORTRAN or IDL algorithms, test the algorithms, and mine data in the data pool. With NADM, the GDAAC provides an environment physically close to the data source. NADM will benefit users with mining or offer data reduction algorithms by reducing large volumes of data before transmission over the network to the user.

Pham, Long↗
NASA NTRS1992

Analyzing high dimensional data

Problems encountered in analyzing high dimensional data are discussed and possible solutions are proposed. The increased importance of second-order statistics in analyzing high dimensional data and the shortcoming of the minimum distance classifier in high dimensional data are recognized. By investigating characteristics of high dimensional data, it is shown that second-order statistics must be taken into account in high dimensional data. There is a need to represent second order statistics effectively. As the data dimensionality increases, it becomes more difficult to perceive and compare information present in statistics derived from data. In order to overcome this problem, a method to visualize statistics using color code is proposed. By representing statistics using a color code, the first and the second statistics can be more readily compared.

Lee, Chulhee↗
NASA NTRS2001

Mapping visual cortex in monkeys and humans using surface-based atlases

We have used surface-based atlases of the cerebral cortex to analyze the functional organization of visual cortex in humans and macaque monkeys. The macaque atlas contains multiple partitioning schemes for visual cortex, including a probabilistic atlas of visual areas derived from a recent architectonic study, plus summary schemes that reflect a combination of physiological and anatomical evidence. The human atlas includes a probabilistic map of eight topographically organized visual areas recently mapped using functional MRI. To facilitate comparisons between species, we used surface-based warping to bring functional and geographic landmarks on the macaque map into register with corresponding landmarks on the human map. The results suggest that extrastriate visual cortex outside the known topographically organized areas is dramatically expanded in human compared to macaque cortex, particularly in the parietal lobe.

Non-NASA Center↗
NASA NTRS1985

Unsteady pressure measurements on a biconvex airfoil in a transonic oscillating cascade

Flush-mounted dynamic pressure transducers were installed on the center airfoil of a transonic oscillating cascade to measure the unsteady aerodynamic response as nine airfroils were simultaneously driven to provide 1.2 deg of pitching motion about the midchord. Initial tests were performed at an incidence and angle of 0 deg and A Mach number of 0.65 in order to obtain results in a shock-free compressible flowfield. Subsequent tests were performed at an incidence angle of 7 deg and Mach number of 0.8 in order to observe the surface pressures with an oscillating shock near the leading edge of the airfoil. Results are presented for interblade phase angles of 90 and -90 deg and at blade oscillatory frequencies of 200 and 500 Hz (semi-chord reduced frequencies up to about 0.5 at a Mach number of 0.8). Results from the zero-incidence cascade are compared with a classical unsteady flat-plate analysis. Flow visualization results depicting the shock motion on the airfoils in the high-incidence cascade are discussed. The airfoil pressure data are tabulated.

Shaw, L. M.↗
NASA NTRS1986

Unsteady pressure measurements on a biconvex airfoil in a transonic oscillating cascade

Flush-mounted dynamic pressure transducers were installed on the center airfoil of a transonic oscillating cascade to measure the unsteady aerodynamic response as nine airfols were simultaneously driven to provide 1.2 deg of pitching motion about the midchord. Initial tests were performed at an incidence and angle of 0 deg and A Mach number of 0.65 in order to obtain results in a shock-free compressible flowfield. Subsequent tests were performed at an incidence angle of 7 deg and Mach number of 0.8 in order to observe the surface pressures with an oscillating shock near the leading edge of the airfoil. Results are presented for interblade phase angles of 90 and -90 deg and at blade oscillatory frequencies of 200 and 500 Hz (semi-chord reduced frequencies up to about 0.5 at a Mach number of 0.8). Results from the zero-incidence cascade are compared with a clasical usnteady flat-plate analysis. Flow visualization results depicting the shock motion on the airfoils in the high-incidence cascade are discussed. The airfoil pressure data are tabulated.

Shaw, L. M.↗
NASA NTRS1987

Optical interferometry in fluid dynamics research

Optical interferometry techniques were applied to the investigation of transonic airfoil flow fields in large wind tunnels. Holographic interferometry techniques were used to study 2 dimensional symmetric NACA 64A010 and Douglas Aircraft Co. DSMA671 supercritical airfoil performance in the NASA Ames 2 x 2 ft transonic wind tunnel. Quantitative data obtained from the interferograms were compared to the surface pressure data. The agreement obtained verified the accuracy of the flow visualization and demonstrated the potential for acquiring quantitative scalar results. Measurements of the inviscid flow speed and the boundary layer and wake velocity profiles were extracted from the interferograms and compared to laser Doppler velocimeter measurements. These results were also in good agreement. A method for acquiring real time interferometric data in large scale facilities was developed. This method, based on the point diffraction interferometer, was successfully tested in the 2 x 2 ft transonic wind tunnel. The holographic and real time interferometry methods were applied to the investigations of circulation control airfoils utilizing the Coanda effect. These results reveals the details of the jet interacting with the trailing edge boundary layer and the other parameters affecting the lift augmentation.

Bachalo, W. D.↗
NASA NTRS1991

The design of electronic map displays

This paper presents a cognitive analysis of a pilot's navigation task and describes an experiment comparing a new map display that employs the principle of visual momentum with the two traditional approaches, track-up and north-up. The data show that the advantage of a track-up alignment is its congruence with the egocentered forward view; however, the inconsistency of the rotating display hinders development of a cognitive map. The stability of a north-up alignment aids the acquisition of a cognitive map, but there is a cost associated with the mental rotation of the display to a track-up alignment for tasks involving the ego-centered forward view. The data also show that the visual momentum design captures the benefits and reduces the costs associated with the two traditional approaches.

Aretz, Anthony J.↗
NASA NTRS1991

Airfoil transition and separation studies using an infrared imaging system

An infrared imaging system was used to detect the thermal signature of boundary-layer flow regimes on a NACA 0012 airfoil from zero angle of attack up to separation. The boundary-layer transition from laminar to turbulent flow and the onset of separation could be seen on the airfoil thermograms. The findings were compared against the behavior of aluminum foil tufts observable both visually and with the infrared imaging system. This arrangement offers the option of using the infrared imaging system both for flow regime detection through surface thermography and flow visualization by the aluminum foil tufts. Ultimately the surface temperature changes due to variation in the angle of attack of a lifting surface provide a means for interpretation of the boundary-layer flow regimes.

Gartenberg, Ehud↗
NASA NTRS1992

Proteus - Geology, shape, and catastrophic destruction

Least-squares fits to the two available limb profiles of Proteus yield a sphericity close to unity; the visual irregularity is due to a degree of surface roughness comparable to that of Hyperion and the smaller icy satellites. A network of streaks that can be interpreted as tectonic troughs cuts the surface of Proteus, and is organized concentrically around either one of the two nearly-coincident Proteus-Neptune of Pharos axes of symmetry. If the streaks are tectonic, they may be due to tidal stresses generated by a past change in Proteus' equilibrium orientation. The streaks may also be disruptive-stress fractures.

Croft, Steven K.↗
NASA NTRS2000

Visual detection of spatial contrast patterns: evaluation of five simple models

The ModelFest Phase One dataset is a collection of luminance contrast thresholds for 43 two-dimensional monochromatic spatial patterns confined to an area of approximately two by two degrees. These data were collected by a collaboration among twelve laboratories, and were designed to provide a common database for calibration and testing of spatial vision models. Here I report fits of the ModelFest data with five models: Peak Contrast, Contrast Energy, Generalized Energy, a Gabor Channels model, and a Discrete Cosine Transform model. The Gabor Channels model provides the best fit, though the other, simpler models, with the exception of Peak Contrast, provide remarkably good fits as well. Though there are clear individual differences, regularities in the data suggest the possibility of constructing a standard observer for spatial vision. c2000 Optical Society of America.

NASA Discipline Space Human Factors↗
NASA NTRS1983

Spatial orientation - Visual-vestibular-somatic interaction

The compensation signals from somatosensory and vestibular receptors, which act to compensate for disturbances produced by the displacement of our eyes relative to other parts of our bodies and for visual disturbances such as tilted frames or moving visual fields, are investigated. Disturbances were evoked by tilting the head and by rotating a large visual display, while compensation signals related to gravity were altered by placing the subjects horizontally on a board or seating them vertically. The first experiment studied the effects of visual disturbance on the ability of supine observers to set a line to the longitudinal body axis while the head was tilted toward one shoulder or while the head was straight. Results showed that the effects of the visual disturbance were greater when the head was tilted than when it was straight, which indicates that the effects of visual disturbance were greater for a task that required compensation. The second experiment compared the performance of supine and erect observers. No differences were found between the performance of observers on a task requiring the use of compensation signals under these two conditions, which suggests that the enrichment of compensatory signals did not reduce the effects of visual disturbancs.

Parker, D. E.↗
NASA NTRS1994

Investigation of ramp injectors for supersonic mixing enhancement

A comparative study of wall mounted swept ramp injectors fitted with injector nozzles of different shape has been conducted in a constant area duct to explore mixing enhancement techniques for scramjet combustors. Six different injector nozzle inserts, all having equal exit and throat areas, were tested to explore the interaction between the preconditioned fuel jet and the vortical flowfield produced by the ramp: circular nozzle (baseline), nozzle with three downstream facing steps, nozzle with four vortex generators, elliptical nozzle, tapered-slot nozzle, and trapezoidal nozzle. The main flow was air at Mach 2, and the fuel was simulated by air injected at Mach 1.63 or by helium injected at Mach 1.7. Pressure and temperature surveys, combined with Mie and Rayleigh scattering visualization, were used to investigate the flow field. The experiments were compared with three dimensional Navier-Stokes computations. The results indicate that the mixing process is dominated by the streamwise vorticity generated by the ramp, the injectors' inner geometry having a minor effect. It was also found that the injectant/air mixing in the far-field is nearly independent of the injector geometry, molecular weight of the injectant, and the initial convective Mach number.

Haimovitch, Y.↗
NASA NTRSDate not supplied

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric surface imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method models. Data collection methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps on how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the pre-processing methods and results from Py_TIGIRS are provided and compared for Composite Test Article (CTA) 8.2B. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future development of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Sandwich structures↗