Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compiler”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Data Compilation for AGR-2 B&W UO2 Coated Particle Batch G73H-10-93085B

Coated particle fuel batch G73H-10-93085B was produced by the Babcock and Wilcox Company (B&W) for use as UO₂ fuel for the Advanced Gas Reactor Fuel Development and Qualification Program’s AGR-2 irradiation test. Batch G73H-10-93085B is a single batch of TRISO-coated 500 μm nominal diameter 10% low enrichment uranium oxide kernels (LEU). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). Argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. B&W samples NP-B8488, NP-B8489, and NP-B8490 (all from batch G73H-10-93085B) were sent to ORNL for characterization and compacting. These samples were composited and renamed LEU10. Samples were then riffled for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Three SiC inclusions were found in a sample of 3510 particles. This corresponds to a defect fraction of <2.3E-3 at 95% confidence. One of these inclusions was of unusual appearance and was determined to contain molybdenum using energy dispersive x-ray analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 Variant Coated Particle Batch G73J-14-93074A

Coated particle fuel batch G73J-14-93074A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO variant fuel for the Advanced Gas Reactor Furl Development and Qualification Program's AGR-2 irradiation test. Batch G73J-14-93074A is a single batch of TRISO-coated 425 μm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). For this variant, argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7979 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by the fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.27 ml/m². One SiC soot inclusion was found in a sample of 4746 particles. This corresponds to <1E-3 defect fraction at 95% confidence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ORNL Data Compilation for the IAEA CRP-6 QC Benchmark Exercise

Four TRISO-coated particle samples were subjected to a battery of quality control (QC) measurements typically used at Oak Ridge National Laboratory for characterization and acceptance testing of coated particle fuel. The results of the analysis will be compared to similar analyses performed by the other participants in a QC benchmark exercise as part of the International Atomic Energy Agency (IAEA) Coordinated Research Project number 6 (CRP-6). The samples in the study were all produced on zirconia spheres as a surrogate material for the uranium bearing fuel kernel. Four of the participating organizations supplied these surrogate fuel samples. The sample suppliers were 1) the Babcock and Wilcox Company (B&W) in the USA, 2) the Korea Atomic Energy Research Institute (KAERI) in South Korea, 3) Pebble Bed Modular Reactor Ltd. in South Africa, and 4) the Oak Ridge National Laboratory (ORNL) in the USA. It should be stressed that the purpose of this exercise is for the comparison and benchmarking of the characterization methods and results. These surrogate coated particles ar enot necessarily representative of the baseline process used by each organization and conclusions should not be drawn regarding fuel performance based on the properties of these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGR-2 Variant Coated Particle Batch G73J-14-93073A

Coated particle fuel batch G73J-14-93073A was produced by the Babcock and Wilcox Company (B&W) for possible selection as UCO variant fuel for the Advanced Gas Reactor Fuel Development and Qualification Program's AGR-2 irradiation test. Batch G73J-14-93073A is a single batch of TRISO-coated 425 μm nominal diameter 14% low enrichment uranium oxide/uranium carbide kernels (LEUCO). The TRISO-coatings consist of a ~50% dense carbon buffer layer (100 μm nominal thickness) followed by a dense inner pyrocarbon layer (40 μm nominal thickness) followed by a SiC layer (35 μm nominal thickness) followed by another dense outer pyrocarbon layer (40 μm nominal thickness). For this variant, argon was added to the hydrogen fluidization gas during SiC deposition. The AGR-2 Fuel Specification (INL SPC-923) provides the requirements necessary for acceptance of the fuel manufactured for the AGR-2 irradiation test. The bulk of the kernels and coated particle acceptance testing was performed at B&W and is not contained in this report. Sample NP-B7958 was sent to ORNL for supplemental characterization. The procedures for the limited characterization and qualification of the particles performed at ORNL are outlined in ORNL product inspection plan AGR-CHAR-PIP-09. The BAFo equivalent optical anisotropies of the inner and outer pyrocarbon layers are reported on Inspection Report Form IRF-09, with a determination as to whether the particle batch satisfied the specified parameters for this property. The batch was found to satisfy the AGR-2 Fuel Specification SPC-923, Rev. 1 for IPyC and OPyC anisotropy. Also provided in this data package are data on the true BAFo, average particle weight, OPyC open porosity, and SiC soot inclusion defect fraction. True BAFo is calculated as (1+N)/(1-N), where N is the diattenuation. This differs from equivalent BAFo = 1+3N, which is the calculation used by fuel specification to allow comparison to historical measurements. Average OPyC open porosity was determined using a single sample to be 0.41 ml/m². One possible SiC soot inclusion was found in a sample of 4729 particles. This corresponds to <1E-3 defect fraction at 95% confidence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Compilation of Historical Data on Hagan Drop Testing with Results

The Hagan nuclear material storage container was designed in the late 1990’s to provide a robust container for daily use, safe transport within the plutonium facility PF-4, and storage of nuclear material for up to twenty years. There are currently >3000 loaded Hagan containers in use at TA-55. The majority of these are in the TA-55 vault, but they are also used in safes and in floor locations on the main floor of PF-4. The original design criteria are given below

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Biota Modeling in EPA’s Preliminary Remediation Goal and Dose Compliance Concentration Calculators for Use in EPA Superfund Risk Assessment: Explanation of Intake Rate Derivation, Transfer Factor Compilation, and Mass Loading Factor Sources

The Preliminary Remediation Goal (PRG) and Dose Compliance Concentration (DCC) calculators are screening level risk assessment tools that set forth the Environmental Protection Agency’s (EPA) recommended approaches and currently available risk assessment guidance for response actions at Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) sites, commonly known as Superfund. The environmental screening levels derived by the PRG and DCC calculators are used to identify isotopes contributing the highest risk and dose as well as establish preliminary remediation goals. Each calculator has residential gardening and subsistence farmer exposure scenarios that model transfer of contaminants from soil and water into various types of biota (crops and animal products). New publications of human intake rates of biota; farm animal intakes of water, soil, and fodder; and soil to plant interactions require updates be implemented into the PRG and DCC calculators. Recent improvements in the biota modeling for these calculators include newly derived biota intake rates, enhanced soil mass loading factors (MLFs), and more comprehensive soil to plant transfer factors (BV’s) and soil to tissue transfer factors (TFs) for animals. New biota have been added in both the produce and animal products categories that greatly improve the accuracy and utility of the PRG and DCC calculators and encompass greater geographic diversity on a national and international scale.

54 ENVIRONMENTAL SCIENCES↗

Compilation and Evaluation of Data from Groundwater Impounded within the U12n and U12t Tunnels, Rainier and Aqueduct Mesas, Nevada National Security Site

The Department of Defense (DOD) Defense Threat Reduction Agency (DTRA) and the U.S. Department of Energy (DOE) Office of Environmental Management Nevada Program (EM NV) conducted routine physical and geochemical monitoring of water impounded behind impermeable structures placed within the U12n and U12t tunnels on the Nevada National Security Site (NNSS) (formerly the Nevada Test Site [NTS]). Desert Research Institute (DRI) conducted a semiquantitative evaluation of pressure data to determine the extent to which the tunnels have been inundated and a qualitative evaluation of monitored geochemical parameters to determine if trends exist that were indicative of hydrologic and/or geochemical processes operating behind the tunnel plugs. Data were also evaluated to determine if monitored radiological parameters exceeded primary standards associated with the Environmental Protection Agency’s (EPA) Safe Drinking Water Act (SDWA) (40 C.F.R. § 141.66).

54 ENVIRONMENTAL SCIENCES↗

Compilation of Off-Gas Vapor and Liquid Phase Organic Information from Scale Melter Testing of LAW Simulants (VSL-17S4450-1, Rev A)

The objective of this statement of work (SOW) is to obtain available offgas data from scale melter testing of low-activity waste (LAW) simulants within the Vitreous State Laboratory’s possession. The data will be used to provide an estimate of the composition and concentration of organic constituents expected to be present in the liquid waste streams generated from offgas treatment at the LAW Vitrification facility during cold commissioning (prior to radioactive commissioning).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Community Planning for Solar: Compiling a Community Solar Action Plan

This document provides an annotated outline for a Community Solar Action Plan. This document is designed to assist community officials, volunteers, and regional planning agency staff in preparing a draft Community Solar Action Plan for a municipality, community, or other jurisdiction. Preparing a Community Solar Action Plan is the fifth step in the Community Planning for Solar process (ag.umass.edu/solarplanning). The plan is intended to be the culmination of the planning process. The contents of the plan will include summaries of information gathered as part of foregoing steps in the process, including completion of a Solar Resource and Infrastructure Assessment, administering of a Community Solar Survey, interpretation of survey results, and review of Solar Financing and Ownership Options and tools. Once the Community Solar Action Plan has been drafted, it should be reviewed by municipal board and commission members and presented at an open community forum. Any important comments or revisions can be incorporated before the final Community Solar Action Plan is approved and implemented. The approved Community Solar Action Plan is a living document that guides community solar planning action over time. As conditions change, new information becomes available, or actions progress over the life of the plan, adjustments may be necessary to maintain the plan's relevance. The Monitoring, Evaluating, and Updating Your Community Solar Action Plan fact sheet (Step 6, Item a) describes some things to consider when updating the Community Solar Action Plan over time.

14 SOLAR ENERGY↗

A Compilation and Review of Alaska Energy Projects

There have been many energy projects proposed in Alaska over the past several decades, from large scale hydro projects that have never been built to small scale village power projects to use local alternative energy sources, many of which have also not been built. This project was initially intended to review these rejected projects to evaluate the economic feasibility of these ideas in the light of current economics. This review included contacting the agencies responsible for reviewing and funding these projects in Alaska, including the Alaska Energy Authority, the Denali Commission, and the Arctic Energy Technology Development Laboratory, obtaining available information about these projects, and analyzing the economic data. Unfortunately, the most apparent result of this effort was that the data associated with these projects was not collected in a systematic way that allowed this information to be analyzed.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

LLNL compiled first pages ordered by ascending B&R code

We aim to develop a fundamental understanding of materials dynamics (from {micro}s to ns) in systems where the required combination of spatial and temporal resolution can only be reached by the dynamic transmission electron microscope (DTEM). In this regime, the DTEM is capable of studying complex transient phenomena with several orders of magnitude time resolution advantage over any existing in-situ TEM. Using the unique in situ capabilities and the nanosecond time resolution of the DTEM, we seek to study complex transient phenomena associated with rapid processes in materials, such as active sites on nanoscale catalysts and the atomic level mechanisms and microstructural features for nucleation and growth associated with phase transformations in materials, specifically in martensite formation and crystallization reactions from the amorphous phase. We also will study the transient phase evolution in rapid solid-state reactions, such as those occurring in reactive multilayer foils (RMLF). Program Impact: The LLNL DTEM possesses unique capabilities for capturing time resolved images and diffraction patterns of rapidly evolving materials microstructure under strongly driven conditions. No other instrument in the world can capture images with <10 nm spatial resolution of interesting irreversible materials processes such as phase transformations, plasticity, or morphology changes with 15 ns time resolution. The development of this innovative capability requires the continuing collaboration of laser scientists, electron microscopists, and materials scientists experienced in time resolved observations of materials that exist with particularly relevant backgrounds at LLNL. The research team has made observations of materials processes that are possible by no other method, such as the rapid crystallization of thin film NiTi that identified a change in mechanism at high heating rates as compared to isothermal anneals through changes in nucleation and growth rates of the crystalline phase. The project is designed to reveal these fundamental processes and mechanisms in rapid microstructure evolution that form the foundation of understanding that is an integral part of the DOE-BES mission.

36 MATERIALS SCIENCE↗