Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressible boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The distortion of a supersonic turbulent boundary layer by bulk compression and surface curvature

An experimental investigation is conducted of the effects of bulk compression and streamline curvature on a turbulent supersonic boundary layer whose incoming Mach number is 2.87. Two different, constant-radius curved wall models were used; the total turning angle in both cases was fixed at 8 deg. While the amplification of the normal stress was approximately the same in both models, the amplification of the shear stress was greater in the one with delta(o)/R value 0.1 than in the model with a value of 0.02. The flow over the latter model appears to be especially complex.

Smits, A. J.↗
NASA NTRS1982

Correlation of Preston-tube data with laminar skin friction (Log No. J12984)

Preston tube data within laminar boundary layers obtained on a sharp ten-degree cone in the NASA Ames eleven-foot transonic wind tunnel are correlated with the corresponding values of theoretical skin friction. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The rms scatter of skin friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston tubes in incompressible pipe flows. In contrast to previous works on Preston tube/skin friction correlations, which are based on the physical height of the probe's face, this satisfactory correlation for compressible boundary layer flows is achieved by accounting for the effects of a variable "effective" height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗
NASA NTRS1995

Linear Stability Regime Analysis of the Compressible Reacting Mixing Layer

Previous investigations have shown that a compressible reacting mixing layer can develop two peaks in the mean density weighted vorticity profile. Linear stability analyses show that at these peaks two distinct 'outer' instability modes appear in addition to the more common central mode, which exists unaccompanied in incompressible nonreacting flows. The present study parametrically analyzes the effects of compressibility, heat release, stoichiometry, and density ratio on the amplification rate and obliquity of each stability mode. The mean profiles used in the spatial stability calculation are generated by self-similar solutions of the compressible boundary layer equations combined with the assumption of infinitely fast chemistry. It is shown that the influence of stoichiometry and density ratio on the peaks of the density weighted vorticity profile determines which modes will dominate. Of particular interest are the conditions where two modes are equally amplified, causing the mixing layer to develop into a 'colayer' structure.

Day, M. J.↗
NASA NTRS1972

Computer program for solving compressible nonsimilar-boundary-layer equations for laminar, transitional, or turbulent flows of a perfect gas

A computer program is described which solves the compressible laminar, transitional, or turbulent boundary-layer equations for planar or axisymmetric flows. Three-point implicit difference relations are used to reduce the momentum and energy equations to finite-difference form. These equations are solved simultaneously without iteration. Turbulent flow is treated by the inclusion of either a two-layer eddy-viscosity model or a mixing-length formulation. The eddy conductivity is related to the eddy viscosity through a static turbulent Prandtl number which may be an arbitrary function of the distance from the wall boundary. The transitional boundary layer is treated by the inclusion of an intermittency function which modifies the fully turbulent model. The laminar-boundary-layer equations are recovered when the intermittency is zero, and the fully turbulent equations are solved when the intermittency is unity.

Price, J. M.↗
NASA NTRS1974

Lee surface flow phenomena over space shuttle at large angles of attack at M sub infinity equal 6

Surface pressure and heat transfer, flow separation, flow field, and oil flow patterns on the leeward side of a space shuttle orbiter model are investigated at a free stream Mach number of 6. The free stream Reynolds numbers are between 1.64 times 10 to the 7th power and 1.31 times 10 to the 8th power per meter, and the angle of attack is varied between 0 deg and 40 deg for the present experiments. The stagnation temperatures for the tests are approximately 500 K and the wall temperature is maintained at 290 K. Existing numerical methods of three-dimensional inviscid supersonic flow theory and compressible boundary layer theory are used to predict the present experimental measurements. Results of the present tests indicate two distinct types of flow separation and surface peak heating depending on the angle of attack.

Zakkay, V.↗
NASA NTRS1975

On the calculation of supersonic separating and reattaching flows

A method is developed for solving the laminar and turbulent compressible boundary layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent layer, shock wave interactions. Several Navier-Stokes solutions are obtained for each of the laminar boundary layer, shock wave interactions considered. Comparison of these solutions indicates a first order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow. Comparison of the present boundary layer solutions with the Navier-Stokes solutions and with data for a given Mach number indicates that as long as the separation bubble is small, the boundary layer approximation yields solutions whose accuracy is comparable to the Navier-Stokes solutions.

Murphy, J. D.↗
NASA NTRS1982

Accurate numerical solution of compressible, linear stability equations

The present investigation is concerned with a fourth order accurate finite difference method and its application to the study of the temporal and spatial stability of the three-dimensional compressible boundary layer flow on a swept wing. This method belongs to the class of compact two-point difference schemes discussed by White (1974) and Keller (1974). The method was apparently first used for solving the two-dimensional boundary layer equations. Attention is given to the governing equations, the solution technique, and the search for eigenvalues. A general purpose subroutine is employed for solving a block tridiagonal system of equations. The computer time can be reduced significantly by exploiting the special structure of two matrices.

Malik, M. R.↗
NASA NTRS1986

Stability and control of compressible flows over a surface with concave-conves curvature

The active control of spatially unstable disturbances in a laminar, two-dimensional, compressible boundary layer over a curved surface is numerically simulated. The control is effected by localized time-periodic surface heating. We consider two similar surfaces of different heights with concave-convex curvature. In one, the height is sufficiently large so that the favorable pressure gradient is sufficient to stabilize a particular disturbance. In the other case the pressure gradient induced by the curvature is destabilizing. It is shown that by using active control that the disturbance can be stabilized. The results demonstrate that the curvature induced mean pressure gradient significantly enhances the receptivity of the flow localized time-periodic surface heating and that this is a potentially viable mechanism in air.

Maestrello, L.↗
NASA NTRS1987

Theoretical investigations, and correlative studies for NLF, HLFC, and LFC swept wings at subsonic, transonic and supersonic speeds

Attention is given to the results of theory/experiment-correlation studies for natural laminar flow, LFC, and hybrid-LFC airfoils at subsonic and supersonic Mach numbers. The method of characteristics, integral compressible boundary layer methods for infinitely swept wings, and a method for prediction of separating turbulent boundary layer characteristics. The integral boundary layer methods are found to be successful at predicting both transonic and supersonic transition phenomena. Computations for wings with 0-50 deg sweep angle, Reynolds number range of 1-30 million, and with and without LFC, are in good agreement with experimental data.

Goradia, S. H.↗
NASA NTRS1989

Comparisons of TVD schemes applied to the Navier-Stokes equations

In this study, the following total variation diminishing (TVD) schemes for solving the Navier-Stokes equations have been tested: the Chakravarthy and Szema (1985) upwind biased TVD scheme, the Harten's upwind TVD scheme described by Yee et al. (1983), and the Yee's (1985) symmetric TVD scheme. The schemes have been compared using three test cases. The first case was the one-dimensional shock tube problem which tested the shock-capturing abilities of the schemes. Chakravarthy's and Harten's schemes gave similar results which were found to be more accurate than the results from Yee's scheme. The second case was a compressible boundary layer which tested the schemes's abilities to solve fiscous flows. In this case, the three schemes yielded almost identical results. Finally, the shock/boundary-layer interaction case studied experimentally by Hakkinen et al. (1959) was computed. Here, Chakravarthy's and Yee's schemes compared most favorably with the published data, with Yee's scheme giving slightly better results.

Buelow, Philip E.↗
NASA NTRS1990

Theory of instability and transition

The strongly nonlinear area of theory is discussed, as well as linear and weakly nonlinear (i.e., perturbation) theories, and it is noted that the weaknesses of the weakly nonlinear theory are essentially the inappropriate formulation in earlier works and the lack of guidance for the choice of the lowest-order basis. Attention is focused on the areas of theoretical/numerical development contributing to understanding the transition mechanism and new means for analyzing and predicting transition quantitatively. The nonlinear stability of nonparallel flows, linear secondary instability, and nonlinear wave interaction are analyzed. The incompressible flow over a flat plate with zero-pressure gradient is chosen as an example, while applications range to other shear flows including three-dimensional and compressible boundary layers.

Herbert, Thorwald↗
NASA NTRS1992

LDA measurements in a Mach 2 flow over a rearward facing step with staged transverse injection

Measurements of the mean velocity field and selected turbulence statistics have been obtained via 2D LDA in a Mach 2 flow over a rearward facing step with downstream transverse injection. Axial mean velocity profiles, profiles of the axial and normal RMS levels, and the correlation coefficient between the axial and normal fluctuating components are presented for locations upstream of the step. These data, through comparison with other reported measurements in zero pressure gradient compressible boundary layers indicate that the boundary layers upstream of the step are consistent with 'quasi-equilibrium' turbulent boundary layers with the adiabatic wall boundary condition. Mean velocity field measurements on the symmetry plane of the tunnel are compared to laser induced iodine fluorescence measurements reported in the literature and obtained in the same facility. This comparison demonstrates the quality of the present LDA data set and shows that particle lag is not significant in the LDA measurements despite the complex nature of the downstream flow.

Wang, J.-A.↗
NASA NTRS1990

Navier-Stokes computation of compressible turbulent flows with a second order closure, part 1

A second order closure turbulence model for compressible flows is developed and implemented in a 2D Reynolds-averaged Navier-Stokes solver. From the beginning where a kappa-epsilon turbulence model was implemented in the bidiagonal implicit method of MACCORMACK (referred to as the MAC3 code) to the final stage of implementing a full second order closure in the efficient line Gauss-Seidel algorithm, numerous work was done, individually and collectively. Besides the collaboration itself, the final product of this work is a second order closure derived from the Launder, Reece, and Rodi model to account for near wall effects, which has been called FRAME model, which stands for FRench-AMerican-Effort. During the reporting period, two different problems were worked out. The first was to provide Ames researchers with a reliable compressible boundary layer code including a wide collection of turbulence models for quick testing of new terms, both in two equations and in second order closure (LRR and FRAME). The second topic was to complete the implementation of the FRAME model in the MAC5 code. The work related to these two different contributions is reported. dilatation in presence of stron shocks. This work, which has been conducted during a work at the Center for Turbulence Research with Zeman aimed also to cros-check earlier assumptions by Rubesin and Vandromme.

Haminh, Hieu↗
NASA NTRS1993

High speed transition prediction

The main objective of this work period was to develop, maintain and exercise state-of-the-art methods for transition prediction in supersonic flow fields. Basic state and stability codes, acquired during the last work period, were exercised and applied to calculate the properties of various flowfields. The development of a code for the prediction of transition location using a currently novel method (the PSE or Parabolized Stability Equation method), initiated during the last work period and continued during the present work period, was cancelled at mid-year for budgetary reasons. Other activities during this period included the presentation of a paper at the APS meeting in Tallahassee, Florida entitled 'Stability of Two-Dimensional Compressible Boundary Layers', as well as the initiation of a paper co-authored with H. Reed of the Arizona State University entitled 'Stability of Boundary Layers'.

Gasperas, Gediminis↗
NASA NTRS1993

Computation of selected eigenvalues of generalized eigenvalue problems

The Arnoldi (1951) and Lanczos (1950) iterative algorithms are used to obtain a few selected eigenvalues of the generalized eigenvalue problem A(x) = lambdaB(x), where A and B are n x n nonsymmetric banded complex matrices. A shift-and-invert strategy is used to increase the rate of convergence toward the desired eigenvalues, and the two approaches are evaluated in view of their performance in a model problem concerning the linear stability of compressible boundary layers. A general scheme for computing the eigenvalues that lie within a 'box' in the complex plane is presented.

Nayar, Narinder↗
NASA NTRS1994

The Aeroacoustics of Supersonic Coaxial Jets

Instability waves have been established as the dominant source of mixing noise radiating into the downstream arc of a supersonic jet when the waves have phase velocities that are supersonic relative to ambient conditions. Recent theories for supersonic jet noise have used the concepts of growing and decaying linear instability waves for predicting radiated noise. This analysis is extended to the prediction of noise radiation from supersonic coaxial jets. Since the analysis requires a known mean flow and the coaxial jet mean flow is not described easily in terms of analytic functions, a numerical prediction is made for its development. The Reynolds averaged, compressible, boundary layer equations are solved using a mixing length turbulence model. Empirical correlations are developed for the effects of velocity and temperature ratios and Mach number. Both normal and inverted velocity profile coaxial jets are considered. Comparisons with measurements for both single and coaxial jets show good agreement. The results from mean flow and stability calculations are used to predict the noise radiation from coaxial jets with different operating conditions. Comparisons are made between different coaxial jets and a single equivalent jet with the same total thrust, mass flow, and exit area. Results indicate that normal velocity profile jets can have noise reductions compared to the single equivalent jet. No noise reductions are found for inverted velocity profile jets operated at the minimum noise condition compared to the single equivalent jet. However, it is inferred that changes in area ratio may provide noise reduction benefits for inverted velocity profile jets.

Dahl, Milo D.↗
NASA NTRS1996

Evaluation of Subgrid-Scale Models for Large Eddy Simulation of Compressible Flows

The objective of this project was to evaluate and develop subgrid-scale (SGS) turbulence models for large eddy simulations (LES) of compressible flows. During the first phase of the project results from LES using the dynamic SGS model were compared to those of direct numerical simulations (DNS) of compressible homogeneous turbulence. The second phase of the project involved implementing the dynamic SGS model in a NASA code for simulating supersonic flow over a flat-plate. The model has been successfully coded and a series of simulations has been completed. One of the major findings of the work is that numerical errors associated with the finite differencing scheme used in the code can overwhelm the SGS model and adversely affect the LES results. Attached to this overview are three submitted papers: 'Evaluation of the Dynamic Model for Simulations of Compressible Decaying Isotropic Turbulence'; 'The effect of the formulation of nonlinear terms on aliasing errors in spectral methods'; and 'Large-Eddy Simulation of a Spatially Evolving Compressible Boundary Layer Flow'.

Blaisdell, Gregory A.↗