SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
During the 1960s NASA Goddard Space Flight Center (GSFC) used the Program Evaluation and Review Technique (PERT) as its principal schedule planning and control tool in flight projects. After a temporary replacement of PERT by other techniques, PERT has been reinstituted on all but one of GSFC's flight projects. PERT has been combined with a computer graphics program which makes it possible to produce PERT drawings in only a few hours' time.
Past studies have shown that touchdown rates of descent (sink rates) are higher in aircraft simulators than in aircraft under similar conditions. The objective of this paper was to use a psychophysical technique to investigate a pilot's ability to distinguish between two different sink rates close to the ground. The pilots observed a collimated computer graphics display of a typical runway with edge, zone, and centerline lights. The results showed that with a forward velocity of 120 knots, pilots could reliably distinguish between a sink rate of 0.5 m/sec (1.7 ft/sec) and 0.9 m/sec (2.9 ft/sec). The results also showed that the absolute rate of sink did not significantly affect the perception of sink rate. Time of sink and total height drop during the sink did affect the minimum detectable difference between sink rates (the differential threshold). The effects were such that a greater time of sink and greater height drop produced lower thresholds
Instructions are given for using the DRILL computer program which converts data contained in an Interactive Computer Graphics System (IGDS) design file to production of a paper tape for driving a numerically controlled drilling machine.
Necessary knowledge is presented on data acquisition and preparation for analysis of thermal imagery of power plant heated discharges remotely sensed from an aircraft, with special emphasis on analog to digital conversion of analog tapes acquired during scanning and to geometrical scaling. The central element in the interactive analysis of thermal imagery is an interactive graphics computer terminal which allows an interpreter to effectively interact with a large-scale computer, providing decisions or data as computations are carried out. A temperature calibration is performed, which the interpreter may test anywhere on the image. When satisfied that calibration is correct, the portion of the image to be analyzed is outlined. Printed and microfiche analyses of the plume are produced. The flow chart of programs for analysis of thermal imagery is presented and discussed in some detail.
A contact analog display called Path-In-The-Sky (PITS) integrates information on airplane attitude, airplane kinematic performance, navigation situation, and path prediction into one instrument. The pictorial format utilized in the PITS display concept was designed to reduce the required instrument scan and to simplify interpretation of informtion with the objective of reducing pilot work load. Described are the symbology of the PITS display, the coordinate systems used to generate the display, and the magnitudes of pertinent geometric characteristics selected during the display development. Also included are examples of the PITS display generated on a stand-alone graphics computer.
ODIN/RLV is a digital computing system for the synthesis and optimization of reusable launch vehicle preliminary designs. The system consists of a library of technology modules in the form of independent computer programs and an executive program, ODINEX, which operates on the technology modules. The technology module library contains programs for estimating all major military flight vehicle system characteristics, for example, geometry, aerodynamics, economics, propulsion, inertia and volumetric properties, trajectories and missions, steady state aeroelasticity and flutter, and stability and control. A general system optimization module, a computer graphics module, and a program precompiler are available as user aids in the ODIN/RLV program technology module library.
APL provides convenient associative data manipulation functions in a high level language. Six statements were added to PL/1 via a preprocessor: CREATE, INSERT, FIND, FOR EACH, REMOVE, and DELETE. They allow complete control of all data base operations. During execution, data base management programs perform the functions required to support the APL language. VAAM is the data base management system designed to support the APL language. APL/VAAM is used by CADANCE, an interactive graphic computer system. VAAM is designed to support heavily referenced files. Virtual memory files, which utilize the paging mechanism of the operating system, are used. VAAM supports a full network data structure. The two basic blocks in a VAAM file are entities and sets. Entities are the basic information element and correspond to PL/1 based structures defined by the user. Sets contain the relationship information and are implemented as arrays.
A comparison study is described which has indicated that the finite element and lumped parameter methods are comparable for steady-state conduction/convection analyses. The finite element model was advantageous because of the ease of model verification with computer graphics. Some problems encountered in constructing compatible thermal and structural models have indicated the need for further methodology developments to automate the transition between thermal and structural analyses. The need for more efficient finite element nonlinear transient algorithms has been cited. With further development in the thermal analysis area, the finite element method offers high potential for an integrated thermal/structural analysis capability.
DSPOBJ is a FORTRAN subroutine to control the display of three-dimensional line networks on a stand-alone, general-purpose, interactive computer graphics system. The program controls the creation and manipulation of transformation matrices for the display and control of multiple sets of line networks. It provides advanced graphics features such as independent and global scaling, rotation and translation, cross-sectioning, reflection, and simultaneous display of four views.
IRAS, a joint United States, Netherlands, United Kingdom astronomical satellite, is scheduled to be launched early in 1981 with the purpose of completing an all-sky survey in the infrared wavelengths from 8 to 120 microns and to observe objects of special interest. The mission design is driven by thermal constraints primarily determined by the Sun and Earth; the orbit and survey strategy must be chosen so as to satisfy the mission requirements before the cryogenic system is depleted of its liquid helium. Computer graphics help the designer choose valid survey strategies and evaluate resulting sky coverage.
Three load limiting seat concepts for general aviation aircraft designed to lower the deceleration of the occupant in the event of a crash were sled tested and evaluated with reference to a standard seat. Dummy pelvis accelerations were reduced up to 50 percent with one of the concepts. Computer program MSOMLA (Modified Seat Occupant Model for Light Aircraft) was used to simulate the behavior of a dummy passenger in a NASA full-scale crash test of a twin engine light aircraft. A computer graphics package MANPLOT was developed to pictorially represent the occupant and seat motion.
A methodological approach to measuring workload was investigated for evaluation of new concepts in VTOL aircraft displays. Physiological, visual response, and conventional flight performance measures were recorded for landing approaches performed in the NASA Visual Motion Simulator (VMS). Three displays (two computer graphic and a conventional flight director), three crosswind amplitudes, and two motion base conditions (fixed vs. moving base) were tested in a factorial design. Multivariate discriminant functions were formed from flight performance and/or visual response variables. The flight performance variable discriminant showed maximum differentation between crosswind conditions. The visual response measure discriminant maximized differences between fixed vs. motion base conditions and experimental displays. Physiological variables were used to attempt to predict the discriminant function values for each subject/condition trial. The weights of the physiological variables in these equations showed agreement with previous studies. High muscle tension, light but irregular breathing patterns, and higher heart rate with low amplitude all produced higher scores on this scale and thus represent higher workload levels.
Papers and discussions on surface representation and its integration with aerodynamics, computers, graphics, wind tunnel model fabrication, and flow field grid generation are presented. Surface definition is emphasized.
Tests were performed to evaluate visual access for berthing and deployment of the Plasma Diagnostic Package (PDP) in Space Transportation 4 Flight (STS-4). The Panel Layout Automated Interactive Design (PLAID), a 3 D computer graphics package, was used to construct models of the PDP, pallet, orbiter payload bay, the Remote Manipulator System (RMS), and other relevant elements to represent the STS-4 configuration. Several different assemblies were made, each one representing a snapshot of the PDP during berth/deploy maneuvers. Thirty-six views were produced during this test.
In the first practical application of laser anemometry to an actual gas turbine engine combustor, the mean velocity and turbulent intensity profiles were measured in a steady-flow combustion rig across an annulus simulating a turbine inlet; to establish a basis for comparison with similar measurements to be made in an operating engine and to confirm current turbine aerodynamics and heat transfer design assumptions. It was necessary to develop a new experimental technique for traversing the annulus due to differential thermal expansion of the cantilevered combustion rig and a new computer-graphics analysis technique for analyzing the velocity histograms due to the high background light intensity. The axial mean velocity and turbulent intensity were uniform across the annulus under all operating conditions and the flow had little or no swirl component. The isothermal mean velocity was doubled by the burning of fuel, however, the isothermal turbulent intensity was relatively unaffected.
A finite element Galerkin formulation is used for the calculation of acoustical modes in uniform ducts with arbitrary geometry, mean flow and lining configuration. Hermitian 'non-conforming' sub-parametric elements are used and the dimensionality of the resulting eigenmatrix is reduced by the use of a condensation scheme based on the compatible eigenvectors in the case with no mean flow. Results are presented for simple circular and rectangular configurations for which exact comparison results are readily calculable. Computer graphics routines required to interpret modal data are described and sample results shown.
A paradigm is developed for the problem of allocating in time a single resource to multiple simultaneous task demands which appear randomly, last for various periods, and offer varying rewards for service. Based upon a dynamic optimizing algorithm plus an estimator, and including response time and future discounting constraints, a model of the human decisionmaker is compared to experimental results for human subjects performing such a task at a computer-graphics terminal. Results indicate a reasonable fit, under various model parameters and task conditions, and suggest interesting hypotheses about the nature of human 'planning ahead' and mental work load.
This paper presents an overview of an automated optical navigation (AON) system, a lower-cost, faster, earth-based stepping stone to onboard systems. AON provides estimation (orbit determination) and maneuver subsystems which are automatically linked to provide the fast response required by the Galileo mission, AON's first user. A real-time interactive executive schedules the subsystems to run concurrently or sequentially and enables interactive computer-graphics displays designed to speed evaluation and certification of navigation solutions. A compact trajectory integrator provides a favorable combination of speed and accuracy. Resident on a low-cost minicomputer and coded primarily in HAL/S, the NASA standard language for flight software, AON approaches a prototype for autonomous onboard navigation systems of the future.