Results for “Configurable lighting” — Page 15

NASA NTRS1973

Pressure loads and aerodynamic force information for the -89A space shuttle orbiter configuration, volume 2

Experimental aerodynamic investigations were conducted on an 0.0405 scale representation of the Rockwell -89A Light Weight Space Shuttle Orbiter. The test purpose was to obtain pressure loads data in the presence of the ground for orbiter structural strength analysis. Aerodynamic force data was also recorded to allow correlation with all pressure loads information. Angles of attack from minus 3 deg to 18 deg and angles of sideslip of 0 deg, plus or minus 50 deg, and plus or minus 10 deg were tested in the presence of the NAAL ground plane. Static pressure bugs were used to obtain a pressure loads survey of the basic configuration, elevon deflections of 5 deg, 10 deg, 15 deg, and minus 20 deg and a rudder deflection of minus 15 deg, at a tunnel dynamic pressure of 40 psi. The test procedure was to locate a maximum of 30 static pressure bugs on the model surface at various locations calculated to prevent aerodynamic and physical interference. Then by various combinations of location the pressure bugs output was to define a complete pressure survey for the fuselages, wing, vertical tail, and main landing gear door.

Mennell, R. C.↗

NASA NTRS1976

Transmission characteristics of a twisted nematic liquid-crystal layer

An approximate analytical expression is calculated for the transmission of thin twisted nematic layers situated between a polarizer/analyzer pair. The approximation assumes that the twist angle of the nematic liquid crystal is smaller than the maximum retardation of the cell. The direction of the incident light is assumed to be parallel to the normal of the electrode. This configuration is analyzed for a general arrangement of polarizer and analyzer; the general result is evaluated for the case of the polarizer parallel and analyzer perpendicular to the liquid-crystal optical axis on the input and output electrodes, respectively. The results show that in the case of a thin twisted nematic layer the transmission depends on the thickness of the layer, on the birefringence of the liquid crystal, and on the wavelength of the light. This is a departure from the well-known independence of the transmission on these parameters for a thick twisted nematic layer.

Grinberg, J.↗

NASA NTRS1963

Apollo 2 Second Generation Lunar Exploration System Studies CFY 1963

The Apollo II Second Generation Lunar Exploration System includes the direct landing spacecraft which consists of cargo command module, service module, and landing module. The landing module is also capable of being used as the Lunar Landing Vehicle (LLV) for landing unmanned cargos consisting of shelter modules such as the Lunar Occupancy Payload and other cargo in support of lunar surface operations. High energy cryogenic propellants are utilized to permit direct landing, manned, or logistic missions with use of a single Saturn V class booster. In last year's studies, the LLV was configured for maximum payload and with consideration for the direct three-man landing and return mission. Light weight and low vehicle height above the lunar surface at touchdown were major objectives. Logistic cargos of more than 27,000 pounds landed on the Moon were achieved within the single Saturn V boost capability. For the manned mission, the lunar take-off weight was determined to be 28,000 pounds ready for the return-to-Earth portion of the mission. The command module utilized was an advanced light-weight design weighing 10,000 pounds including supporting subsystems. Cryogenic oxygen/hydrogen propulsion was again used for maximum propulsion efficiency. Study of the Lunar Occupancy Payload was also accomplished last year. This module was configured to serve as an early lunar shelter or outpost station or as a basic module of an integrated base module complex. Single and dual compartment versions, as well as special mission versions, were studied.

Matzenaur, J. O.↗

DOE OSTI2025

Decay heat analysis for advanced reactor spent fuel transportation and storage applications

Accurate characterization of nuclide inventories and decay heat in spent nuclear fuel is critical for ensuring its safe handling, storage, transportation, and disposal. Although extensive research has been conducted on light-water reactor fuel, advanced reactors present unique challenges due to their diverse core configurations, fuel characteristics, neutron energy spectra, and burnup levels. Building upon previous efforts that developed representative reactor core models for various advanced reactor types and fuels, this study evaluates reactor-specific decay heat characteristics. The results highlight significant variations across advanced reactor types as well as across reactor designs within the same reactor type, and they provide comparison to typical commercial light-water reactor fuel. For example, thermal-spectrum reactor fuels were observed to have an approximately 100-fold decrease in decay heat over the first decade of cooling, whereas the reduction was 10-fold for fast-spectrum reactor fuels. Mass-specific decay heat at discharge can differ by three orders of magnitude among the fast and thermal reactor systems considered. Overall, for the analyzed advanced reactor fuel, fewer than 17 nuclides account for over 99% of total decay heat at 0.5 years, and that number drops to fewer than 7 nuclides at 100 years of cooling. By quantifying reactor-specific decay heat trends and nuclide contributions, this work provides a technical basis to support the development of spent fuel management strategies for advanced reactor fuels as well as safety evaluations for storage, transportation, and long-term waste disposal.

Advanced reactors↗

NASA NTRS1993

LRAT: Lightning Radiative Transfer

In this report, we extend to cloud physics the work done for single and multiple scattering of electromagnetic waves. We consider the scattering of light, visible or infrared, by a spherical cloud represented by a statistically homogeneous ensemble of configurations of N identical spherical water droplets whose centers are uniformly distributed in its volume V. The ensemble is specified by the average number rho of scatterers in unit volume and by rho f(R) with f(R) as the distribution function for separations R of pairs. The incident light, vector-phi(sub 0) a plane electromagnetic wave with harmonic time dependence, is from outside the cloud. The propagation parameter kappa(sub 0) and the index of refraction eta(sub 0) determine physically the medium outside the distribution of scatterers. We solve the interior problem separately to obtain the bulk parameters for the scatterer equivalent to the ensemble of spherical droplets. With the interior solution or the equivalent medium approach, the multiple scattering problem is reduced to that of an equivalent single scatterer excited from outside illumination. A dispersion relation which determines the bulk propagation parameter K and the bulk index of refraction eta of the cloud is given in terms of the vector equivalent scattering amplitude vector-G and the dyadic scattering amplitude tilde-g of the single object in isolation. Based on this transfer model we will have the ability to consider clouds composed of inhomogeneous distribution of water and/or ice particles and we will be able to take into account particle size distributions within the cloud. We will also be able to study the effects of cloud composition (i.e., particle shape, size, composition, orientation, location) on the polarization of the single or the multiple scattered waves. Finally, this study will provide a new starting point for studying the problem of lightning radiative transfer.

Phanord, Dieudonne D.↗

NASA NTRS2022

Quantifying Errors in 3D CME Parameters Derived from Synthetic Data Using White-Light Reconstruction Techniques

Current efforts in space weather forecasting of CMEs have been focused on predicting their arrival time and magnetic structure. To make these predictions, methods have been developed to derive the true CME speed, size, position, and mass, among others. Difficulties in determining the input parameters for CME forecasting models arise from the lack of direct measurements of the coronal magnetic fields and uncertainties in estimating the CME 3D geometric and kinematic parameters after eruption. White-light coronagraph images are usually employed by a variety of CME reconstruction techniques that assume more or less complex geometries. This is the first study from our International Space Science Institute (ISSI) team “Understanding Our Capabilities in Observing and Modeling Coronal Mass Ejections”, in which we explore how subjectivity affects the 3D CME parameters that are obtained from the Graduated Cylindrical Shell (GCS) reconstruction technique, which is widely used in CME research. To be able to quantify such uncertainties, the “true” values that are being fitted should be known, which are impossible to derive from observational data. We have designed two different synthetic scenarios where the “true” geometric parameters are known in order to quantify such uncertainties for the first time. We explore this by using two sets of synthetic data: 1) Using the ray-tracing option from the GCS model software itself, and 2) Using 3D magnetohydrodynamic (MHD) simulation data from the Magnetohydrodynamic Algorithm outside a Sphere code. Our experiment includes different viewing configurations using single and multiple viewpoints. CME reconstructions using a single viewpoint had the largest errors and error ranges overall for both synthetic GCS and simulated MHD white-light data. As the number of viewpoints increased from one to two, the errors decreased by approximately 4° in latitude, 22° in longitude, 14° in tilt, and 10° in half-angle. Our results quantitatively show the critical need for at least two viewpoints to be able to reduce the uncertainty in deriving CME parameters. We did not find a significant decrease in errors when going from two to three viewpoints for our specific hypothetical three spacecraft scenario using synthetic GCS white-light data. As we expected, considering all configurations and numbers of viewpoints, the mean absolute errors in the measured CME parameters are generally significantly higher in the case of the simulated MHD white-light data compared to those from the synthetic white-light images generated by the GCS model. We found the following CME parameter error bars as a starting point for quantifying the minimum error in CME parameters from white-light reconstructions: Δθ (latitude)=6° +2° -3° , Δϕ (longitude)=11° +18° -6° , Δγ (tilt)=25° +8° -7° , Δx (half-angle)=10° +12° -6° , Δh (height)=0.6 +1.2 -0.4 R ⨀ , and Δκ (ratio)=0.1 +0.03 -0.02 .

Coronal mass ejections↗

NASA NTRS2022

Quantifying Errors in 3D CME Parameters Derived From Synthetic Data Using White-Light Reconstruction Techniques

Current efforts in space weather forecasting of CMEs have been focused on predicting their arrival time and magnetic structure. To make these predictions, methods have been developed to derive the true CME speed, size, position, and mass, among others. Difficulties in determining the input parameters for CME forecasting models arise from the lack of direct measurements of the coronal magnetic fields and uncertainties in estimating the CME 3D geometric and kinematic parameters after eruption. White-light coronagraph images are usually employed by a variety of CME reconstruction techniques that assume more or less complex geometries. This is the first study from our International Space Science Institute (ISSI) team “Understanding Our Capabilities in Observing and Modeling Coronal Mass Ejections”, in which we explore how subjectivity affects the 3D CME parameters that are obtained from the Graduated Cylindrical Shell (GCS) reconstruction technique, which is widely used in CME research. To be able to quantify such uncertainties, the “true” values that are being fitted should be known, which are impossible to derive from observational data. We have designed two different synthetic scenarios where the “true” geometric parameters are known in order to quantify such uncertainties for the first time. We explore this by using two sets of synthetic data: 1) Using the ray-tracing option from the GCS model software itself, and 2) Using 3D magnetohydrodynamic (MHD) simulation data from the Magnetohydrodynamic Algorithm outside a Sphere code. Our experiment includes different viewing configurations using single and multiple viewpoints. CME reconstructions using a single viewpoint had the largest errors and error ranges overall for both synthetic GCS and simulated MHD white-light data. As the number of viewpoints increased from one to two, the errors decreased by approximately 4° in latitude, 22° in longitude, 14° in tilt, and 10° in half-angle. Our results quantitatively show the critical need for at least two viewpoints to be able to reduce the uncertainty in deriving CME parameters. We did not find a significant decrease in errors when going from two to three viewpoints for our specific hypothetical three spacecraft scenario using synthetic GCS white-light data. As we expected, considering all configurations and numbers of viewpoints, the mean absolute errors in the measured CME parameters are generally significantly higher in the case of the simulated MHD white-light data compared to those from the synthetic white-light images generated by the GCS model. We found the following CME parameter error bars as a starting point for quantifying the minimum error in CME parameters from white-light reconstructions: Δθ (latitude)=6° +2° -3° , Δϕ (longitude)=11° +18° -6° , Δγ (tilt)=25° +8° -7° , Δx (half-angle)=10° +12° -6° , Δh (height)=0.6 +1.2 -0.4 R ⨀ , and Δκ (ratio)=0.1 +0.03 -0.02 .

Coronal mass ejections↗

DOE OSTI2025

Enhancing traffic safety analysis with digital twin technology: integrating vehicle dynamics and environmental factors into microscopic traffic simulation

Traffic safety is a critical concern in transportation engineering and urban planning. Traditional traffic safety analysis requires trained observers to collect data in the field, which is time-consuming, labor-intensive, and sometimes inaccurate. In recent years, microscopic traffic simulation, which simulates individual vehicles’ movements within a transportation network, have been utilized to study traffic safety. However, microscopic traffic simulation only focuses on traffic-related factors, such as traffic volume, traffic signals, and lane configurations, neglecting vehicle dynamics and environment-related factors like weather and lighting conditions, which can significantly impact traffic safety. In light of this, this paper explores the application of digital twin technology in traffic safety analysis, integrating vehicle simulators, which consider vehicle dynamics and environmental factors, and microscopic traffic simulators, which simulate the operations of traffic flow, for enhanced safety evaluations. Various scenarios, including different weather conditions and visibility levels, are simulated using a digital twin of a road segment in Tuscaloosa, Alabama. The simulations employ Surrogate Safety Measures (SSMs) like Time to Collision (TTC) and Deceleration Rate to Avoid a Crash (DRAC) to assess safety under varying conditions. The results demonstrate that traffic digital twin can identify potential safety issues that traditional microscopic simulation cannot, providing insights for improving traffic control strategies and transportation infrastructure to enhance traffic safety.

Civil engineering↗

DOE OSTI2025

User Manual for BLADE main.py

This manual provides step-by-step instructions for installing, configuring, and using BLADE, an automated framework for analyzing and classifying bolide light curves from NASA CNEOS datasets. BLADE enables efficient, reproducible analysis of atmospheric entry phenomena, supporting planetary defense and atmospheric science research through standardized signal processing and event classification.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1974

Results from computer program for analyzing scattered light suppression systems for large space telescope

A computer program was developed which has the ability to analyze the performance of most light suppression systems so as to predict the amount of scattered light which will reach the image plane for various conditions of unwanted light input from the sun, earth, or moon. This program was used to analyze three different configurations of the large space telescope (LST): an LST with a truncated sunshield, an LST with an extended cylindrical sunshield, and an LST with a conical sunshield which is tilted upwards. The computer program gives the user detailed information as to the paths taken by the unwanted stray light to reach the image plane, and pinpoints those portions of the light suppression system which contribute most of the stray light, so that areas requiring improvements are evident. Certain design guide lines were formulated for any light suppression system selected for the LST, and one which meets these requirements (the tilted sunshade) is described in detail.

Tifft, W. G.↗

NASA NTRS1979

Criteria for self-ignition of supersonic hydrogen-air mixtures

A correlation of available self ignition data for supersonic hydrogen-air mixtures in configurations representative of scramjet combustors was made. The correlation was examined in light of simplified ignition-limit models. The data and model included cases of injection from transverse fuel jets on walls, transverse jets behind swept and unswept steps, and transverse injection ahead of swept and unswept steps and strut bases. The results provide useful guidance for predicting self ignition in a variety of applications. The likely regions for self ignition in a combustor are given in order of merit.

Huber, P. W.↗

NASA NTRS1979

Residual nutational activity of the sunflower hypocotyl in simulated weightlessness

The gravity dependence of circumnutational activity in the sunflower hypocotyl is investigated under conditions of simulated weightlessness. Seedling cultures of the sunflower Helianthus annuus were placed four days after planting in clinostats rotating at a rate of 1.0 rpm in the horizontal or somersaulting configurations, and plant movements around their growth axes were recorded in infrared light by a time-lapse closed-circuit video system. The amplitudes and mean cycle durations of the plant nutations in the horizontal and tumbling clinostats are observed to be 20% and 72%, and 32% and 74%, respectively, of the values observed in stationary plants; extrapolations to a state of zero g by the imposition of small centripetal forces on horizontally clinostated plants also indicate some nutational motion in the absence of gravity. It is concluded that the results are incompatible with the model of Israelsson and Johnsson (1967) of geotropic response with overshoot for sunflower circumnutation; however, results of the Spacelab 1 mission experiment are needed to unambiguously define the role of gravitation.

Chapman, D. K.↗

NASA NTRS1984

Design parameters for flow energizers

One of the most significant uses of flow energizers, which are small highly swept strakes mounted immediately above a lifting surface, is in flow control over regions where a lifting surface is joined to another body, such as a fuselage or nacelle. In the presently reported systematic wind tunnel test study of flow energizers, 14 different geometric configurations using a 75-deg sweep flow energizer were tested on a light twin-engine general aviation aircraft model. It is found that cambered flow energizers perform better than their flat counterparts. All but two of the energizer installations developed lower L/D at cruise angles of attack, lower maximum lift coefficients, and lower stall angles of attack than the baseline model.

Ward, D. T.↗

NASA NTRS1986

The dynamics of magnetically trapped fluids. I - Implications for umbral dots and penumbral grains

A study of the magnetohydrodynamic system in which a nonmagnetized fluid in a gravitational field is surrounded by a fluid carrying a vertical magnetic field is presented. It is pointed out that this study can throw some light on the fine-structural features of a sunspot. The equilibrium configuration of the field-free fluid is a tapering column ending at an apex. The regions away form the apex can be studied by the slender flux tube approximation. A scheme developed to treat the apex indicates that, just below the apex, the radius of the tapering column opens up with a 3/2 power dependence on the depth below the apex. If the internal pressure of the field-free fluid is increased, the apex rises, and a static equilibrium may not be possible beyond a limit if the magnetic pressure drops quickly above a certain height. The nature of steady-flow solutions beyond this limit is investigated. Under conditions inside a sunspot, a column of field-free gas is found to rise with a velocity of about 100 km/hr. If umbral dots and penumbral grains are interpreted as regions where the field-free gas ultimately emerges, a very natural explanation of most of their observed properties is obtained.

Choudhuri, A. R.↗

NASA NTRS1987

Spatial light modulation by beam coupling in GaAs crystals

The first demonstration of spatial light modulation in GaAs using the photorefractive effect is reported. A special configuration was employed in which polarization rotation created by beam coupling was utilized. The ability to obtain these results despite a small coupling gain coefficient demonstrates the usefulness of the polarization technique presented here for optical processing with GaAs crystals.

Cheng, Li-Jen↗

NASA NTRS1999

Interpreting Broad Double-Peaked Emission Lines in Active Galactic Nuclei

The principal objectives of this project were to probe the inner regions of active galactic nuclei and to test general relativity in the strong-field limit. The approach takes advantage of broad atomic line emission observed from material deep in the potential well of an active galactic nucleus which contains key information as to the physics of the system. Line profiles in a wide range of wavebands from optical to X-ray have provided compelling evidence of the existence of a relativistic accretion disk around a supermassive black hole in a number of galaxies. The simplest model posits a geometrically thin disk in Keplerian orbit, with general relativistic effects in evidence. This model is the point of departure for the proposed work. We developed a high-performance numerical code to calculate photon trajectories in a Schwarzschild or Kerr metric and implemented it on parallel supercomputers. This code includes a general purpose ray tracer that calculates line profiles, light curves, and other observable quantities for a wide variety of emitter configurations. The versatility comes from the fact that the ray tracing algorithm does not depend on any symmetries regarding emitter locations. The speed comes from parallel implementation which enables us to sample hitherto unattainable volumes of disk model parameter space. During the period 1 March 1997 through 28 February 1998, two papers, supported in whole or in part by this grant, were published in refereed journals. They are reproduced in their entirety in the next two sections of this report.

Halpern, Jules↗

NASA NTRS1997

Structural Verification of the Space Shuttle's External Tank Super LightWeight Design: A Lesson in Innovation

The Super LightWeight Tank (SLWT) team was tasked with a daunting challenge from the outset: boost the payload capability of the Shuttle System by safely removing 7500 lbs. from the existing 65,400 lb. External Tank (ET). Tools they had to work with included a promising new Aluminum Lithium alloy, the concept of a more efficient structural configuration for the Liquid Hydrogen (LH2) tank, and a highly successful, mature Light Weight Tank (LWT) program. The 44 month schedule which the SLWT team was given for the task was ambitious by any measure. During this time the team had to not only design, build, and verify the new tank, but they also had to move a material from the early stages of development to maturity. The aluminum lithium alloy showed great promise, with an approximately 29% increase in yield strength, 15% increase in ultimate strength, 5 deg/O increase in modulus and 5 deg/O decrease in density when compared to the current 2219 alloy. But processes had to be developed and brought under control, manufacturing techniques perfected, properties characterized, and design allowable generated. Because of the schedule constraint, this material development activity had to occur in parallel with design and manufacturing. Initial design was performed using design allowable believed to be achievable with the Aluminum Lithium alloy system, but based on limited test data. Preliminary structural development tests were performed with material still in the process of iteration. This parallel path approach posed obvious challenges and risks, but also allowed a unique opportunity for interaction between the structures and materials disciplines in the formulation of the material.

Otte, Neil↗

NASA NTRS2011

The Preflight Calibration of the Thermal Infrared Sensor (TIRS) on the Landsat Data Continuity Mission

The preflight calibration testing of TIRS evaluates the performance of the instrument at the component, subsystem and system level, The overall objective is to provide an instrument that is well calibrated and well characterized with specification compliant data that will ensure the data continuity of Landsat from the previous missions to the LDCM, The TIRS flight build unit and the flight instrument were assessed through a series of calibration tests at NASA Goddard Space Flight Center. Instrument-level requirements played a strong role in defining the test equipment and procedures used for the calibration in the thermal/vacuum chamber. The calibration ground support equipment (CGSE), manufactured by MEI and ATK Corporation, was used to measure the optical, radiometric and geometric characteristics of TIRS, The CGSE operates in three test configurations: GeoRad (geometric, radiometric and spatial), flood source and spectral, TIRS was evaluated though the following tests: bright target recovery, radiometry, spectral response, spatial shape, scatter, stray light, focus, and uniformity, Data were obtained for the instrument and various subsystems under conditions simulating those on orbit In the spectral configuration, a monochromator system with a blackbody source is used for in-band and out-of-band relative spectral response characterization, In the flood source configuration the entire focal plane array is illuminated simultaneously to investigate pixel-to-pixel uniformity and dead or inoperable pixels, The remaining tests were executed in the GeoRad configuration and use a NIST calibrated cavity blackbody source, The NIST calibration is transferred to the TIRS sensor and to the blackbody source on-board TIRS, The onboard calibrator will be the primary calibration source for the TIRS sensor on orbit.

Smith, Ramsey↗