Search NASA⌕ Search

SEARCH · Search NASA

Results for “DEMONSTRATION PROGRAMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

CARBON BED MERCURY EMISSIONS CONTROL FOR MIXED WASTE TREATMENT

Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according tohe Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB® carbon can sorb Hg up to 19 wt% of the carbon mass, and (c) the spent carbon retained almost all (98 – 99.99%) of the Hg; but when even a small fraction of the total Hg dissolves, the spent carbon can fail the TCLP test when the spent carbon contains high Hg concentrations. Localized areas in a carbon bed that become heated through heat of adsorption, to temperatures where oxidation occurs, are referred to as “bed hot spots.” Carbon bed hot spots must be avoided in processes that treat radioactive and mixed waste. Key to carbon bed hot spot mitigation are (a) designing for sufficient gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) monitoring and control of inlet gas flowrate, temperature, and composition, (c) monitoring and control of in-bed and bed outlet gas temperatures, and (d) most important, monitoring of bed outlet CO concentrations. An increase of CO levels in the off-gas downstream of the carbon bed to levels about 50-100 ppm higher than the inlet CO concentration indicate CO formation in the bed, caused by carbon bed hot spots. Corrective actions must be implemented quickly if bed hot spots are detected, using a graded approach and sequence starting with corrective actions that are simple, quick, cause the least impact to the process, and are easiest to recover from. Multiple high and high-high alarm levels should be used, with appropriate corrective actions for each level.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

AN INFORMATION-THEORETIC APPROACH TO OPTIMIZE JWST OBSERVATIONS AND RETRIEVALS OF TRANSITING EXOPLANET ATMOSPHERES

We provide an example of an analysis to explore the optimization of observations of transiting hot Jupiters with the James Webb Space Telescope ( JWST ) to characterize their atmospheres based on a simple three-parameter forward model. We construct expansive forward model sets for 11 hot Jupiters, 10 of which are relatively well characterized, exploring a range of parameters such as equilibrium temperature and metallicity, as well as considering host stars over a wide range in brightness. We compute posterior distributions of our model parameters for each planet with all of the available JWST spectroscopic modes and several programs of combined observations and compute their effectiveness using the metric of estimated mutual information per degree of freedom. From these simulations, clear trends emerge that provide guidelines for designing a JWST observing program. We demonstrate that these guidelines apply over a wide range of planet parameters and target brightnesses for our simple forward model.

79 ASTRONOMY AND ASTROPHYSICS↗

Integrated Modeling, Mapping, and Simulation (IMMS) framework for planning exercises.

The Integrated Modeling, Mapping, and Simulation (IMMS) program is designing and prototyping a simulation and collaboration environment for linking together existing and future modeling and simulation tools to enable analysts, emergency planners, and incident managers to more effectively, economically, and rapidly prepare, analyze, train, and respond to real or potential incidents. When complete, the IMMS program will demonstrate an integrated modeling and simulation capability that supports emergency managers and responders with (1) conducting 'what-if' analyses and exercises to address preparedness, analysis, training, operations, and lessons learned, and (2) effectively, economically, and rapidly verifying response tactics, plans and procedures.

99 GENERAL AND MISCELLANEOUS↗

ALTERNATIVES OF MACCS2 IN LANL DISPERSION ANALYSIS FOR ONSITE AND OFFSITE DOSES

In modeling atmospheric dispersion to determine accidental release of radiological material, one of the common statistical analysis tools used at Los Alamos National Laboratory (LANL) is MELCOR Accident Consequence Code System, Version 2 (MACCS2). MACCS2, however, has some limitations and shortfalls for both onsite and offsite applications. Alternative computer codes, which could provide more realistic calculations, are being investigated for use at LANL. In the Yucca Mountain Project (YMP), the suitability of MACCS2 for the calculation of onsite worker doses was a concern; therefore, ARCON96 was chosen to replace MACCS2. YMP's use of ARCON96 provided results which clearly demonstrated the program's merit for onsite worker safety analyses in a wide range of complex configurations and scenarios. For offsite public exposures, the conservatism of MACCS2 on the treatment of turbulence phenomena at LANL is examined in this paper. The results show a factor of at least two conservatism in calculated public doses. The new EPA air quality model, AERMOD, which implements advanced meteorological turbulence calculations, is a good candidate for LANL applications to provide more confidence in the accuracy of offsite public dose projections.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

MueLu Multigrid Preconditioning Package

MueLu is intended for the research and development of multigrid algorithms used in the solution of sparse linear systems arising from systems of partial differential equations. The software provides multigrid source code, test programs, and short example programs to demonstrate the various interfaces for creating, accessing, and applying the solvers. MueLu currently provides an implementation of smoothed aggregation algebraic multigrid method and interfaces to many commonly used smoothers. However, the software is intended to be extensible, and new methods can be incorporated easily. MueLu also allows for advanced usage, such as combining multiple methods and segregated solves. The library supports point and block access to matrix data. All algorithms and methods in MueLu have been or will be published in the open scientific literature.

Source record↗

Scenario Creation and Power-Conditioning Strategies for Operating Power Grids with Two-Stage Stochastic Economic Dispatch: Preprint

A significant difficultly associated with the use of stochastic programming to solve optimal power flow problems on a 5-minute timescale is the quality of renewable energy scenarios input by the user. This is especially true when considering power systems with high penetrations of renewable energy, e.g. wind power. This paper introduces the use of stochastic programming to solve the DCOPF problem with scenarios drawn directly from high-fidelity data sets. Hence, the proposed method avoids the problem of lost physics by finding high-fidelity analogs that can describe future states of the system. Furthermore, this method can be simply extended to output multi-period scenarios to the stochastic program. We demonstrate the effectiveness of this technique on simulated dispatch operations of the RTS-GMLC over a week.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assessment of Cladding-Cladding Delamination Failures in U-Mo Fuel Plates

Monolithic fuel is a candidate fuel form for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo alloy-based fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To qualify this fuel system, the program must demonstrate that the fuel meets the safety standards, has a predictable behavior, and performs well in a reactor. Although many plates have shown satisfactory thermo-mechanical performance in reactor, a small number of experimental plates exhibited failures, rendering performance of these plates unacceptable. Post-irradiation examinations of failed plates have revealed that various failures modes are present, including pillowing, blistering, buckling, warping, delamination, fracture, rupture, oxide spallation, etc. Previous studies have implied that such various operational and loading conditions could generate a complex stress-strain state, facilitating distinct failure modes that could impact the structural integrity. To understand such various failure modes, a comprehensive set of studies focusing on failure modes is being performed. As a part of these studies, this work studies the cladding-cladding separation failures that were observed in some of previous irradiation tests. To understand the root cause of cladding separation failures, selected plates from previous irradiation experiments were simulated under comparable operational conditions. Stress-strain state of the plates at the interface were examined. The results were comparatively evaluated to understand possible effects of stress state of the bond-line on delamination failures. This paper presents these findings, discusses such failure modes, and examines the influence of various factors on previously observed cladding delamination failures.

42 ENGINEERING↗

Future Advances in Photon-Based Neutrino Detectors: A SNOWMASS White Paper

We discuss here new, enabling technologies for future photon-based neutrino detectors. These technologies touch nearly every aspect of such detectors: new scintillating materials, new methods of loading isotopes, new photon sensors and collectors, new approaches to simulation and analysis, and new front-end electronics and DAQ ideas. Of particular interest are technologies that enable broad physics programs in hybrid Cherenkov/scintillation detectors, such as slow fluors, water-based liquid scintillator, and spectral sorting of photons. Several new large-scale detector ideas are also discussed, including hybrid detectors like Theia, ArTEMIS, and generic slow-fluor detectors, as well as the very different SLIPs and LiquidO approaches to instrumenting photon-based detectors. A program of demonstrators for future detectors, including ANNIE, Eos, and NuDOT are also discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Coal without carbon: an investment plan for federal action

This study examines several technologies for CCS that are not currently receiving adequate development support but that could - in the right policy environment - provide the kind of significant cost reductions (and significant improvements in efficiency) that could greatly accelerate broad, economically attractive CCS deployment. Clean Air Task Force selected these technology areas (though not the technologies themselves) and solicited reports from experts in each field to explore how these technologies might fit into a broader CCS deployment strategy. Each expert was asked to develop a research, development, and demonstration (RD&D) 'road map' that could efficiently move each technology from the laboratory into the commercial mainstream. Because the chapter authors are either technical experts or commercial players and are not, for the most part, energy policy experts, subsequent work will translate their RD&D recommendations into actionable policy proposals. The heart of this report consists of four chapters on advanced coal and CCS technologies: underground coal gasification (UCG), written by Julio Friedmann at Lawrence Livermore National Laboratory; Next generation coal gasification (surface-based gasification) led by Eric Redman at Summit Power Group; Advanced technologies for post-combustion capture (PCC) of CO{sub 2}, led by Howard Herzog at Massachusetts Institute of Technology; and RD&D to speed commercialization of geological CO{sub 2} sequestration (GCS), led by Julio Friedmann. 12 refs., 5 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Role of research reactors in training of NPP personnel with special focus on training reactor VR-1

Research reactors play an important role in providing key personnel of nuclear power plants a hands-on experience from operation and experiments at nuclear facilities. Training of NPP (Nuclear Power Plant) staff is usually deeply theoretical with an extensive utilisation of simulators and computer visualisation. But a direct sensing of the reactor response to various actions can only improve the personnel awareness of important aspects of reactor operation. Training Reactor VR-1 and its utilization for training of NPP operators and other professionals from Czech Republic and Slovakia is described. Typical experimental exercises and good practices in organization of a training program are demonstrated. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

GDOE Bearing

Explore the source record for details and available documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

GAIN Base Presentation Slide Deck 2/12/25

The GAIN Base Slide Deck is a compilation of topics that GAIN presents routinely to outside entities to educate them on the GAIN program, technology, demonstrations, coal to nuclear, energy systems, Financing, Supply Chain, Legislation, Regulatory, and Consent Based Citing.

99 - GENERAL AND MISCELLANEOUS↗

Machine Learning for Well Log Analysis in Uranium Mining

This project explores the use of Artificial Intelligence (AI) and Machine Learning (ML) techniques to automate well log analysis for uranium mining. Geophysical log data—spontaneous potential, resistivity, and gamma ray—were used to classify lithology, correlate well logs and identify roll front zonation patterns, which are critical for locating uranium ore bodies. Supervised ML algorithms such as eXtreme Gradient Boosting (XGBoost), Categorical Boosting (CatBoost), and Random Forest were trained to classify lithology with high accuracy. Gradient Boosting Machines (GBM), XGBoost, Random Forest, and Neural Networks were also used for role front zone identification. Moreover, a Fast Dynamic Time Warping (FastDTW) algorithm was employed for well log correlation. Additionally, sample lag was addressed using dynamic programming. Results demonstrate the potential of AI and ML to streamline well log analysis and enhance uranium exploration workflows.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication and Comparison of Fuels for Advanced Gas Reactor Irradiation Tests

As part of the program to demonstrate TRISO-coated fuel for the Next Generation Nuclear Plant, a series of irradiation tests of Advanced Gas Reactor (AGR) fuel are being performed in the Advanced Test Reactor (ATR) at the Idaho National Laboratory. In the first test, called “AGR-1,” graphite compacts containing approximately 300,000 coated particles were irradiated from December 2006 until November 2009. Development of AGR-1 fuel sought to replicate the properties of German TRISO-coated particles. No particle failures were seen in the nearly 3-year irradiation to a burn up of 19%. The AGR-1 particles were coated in a two-inch diameter coater. Following fabrication of AGR-1 fuel, process improvements and changes were made in each of the fabrication processes. Changes in the kernel fabrication process included replacing the carbon black powder feed with a surface-modified carbon slurry and shortening the sintering schedule. AGR-2 TRISO particles were produced in a six-inch diameter coater using a change size about twenty-one times that of the two-inch diameter coater used to coat AGR-1 particles. Changes were also made in the compacting process, including increasing the temperature and pressure of pressing and using a different type of press. Irradiation of AGR-2 fuel began in late spring 2010. Properties of AGR-2 fuel compare favorably with AGR-1 and historic German fuel. Kernels are more homogeneous in shape, chemistry and density. TRISO-particle sphericity, layer thickness standard deviations, and defect fractions are also comparable. In a sample of 317,000 particles from deconsolidated AGR-2 compacts, 3 exposed kernels were found in a leach test. No SiC defects were found in a sample of 250,000 deconsolidated particles, and no IPyC defects in a sample of 64,000 particles. The primary difference in properties between AGR-1 and AGR-2 compacts is that AGR-2 compacts have a higher matrix density, 1.6 g/cm3 compared to about 1.3 g/cm3 for AGR-1 compacts. Based on fuel properties, excellence performance is expected for the AGR-2 UCO fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SU-F-J-116: Clinical Experience-Based Verification and Improvement of a 4DCT Program

Purpose: To demonstrate the role of continuous improvement fulfilled by the Medical Physicist in clinical 4DCT and CBCT scanning. Methods: Lung (SABR and Standard) patients’ 4D respiratory motion and image data were reviewed over a 3, 6 and 12 month period following commissioning testing. By identifying trends of clinically relevant parameters and respiratory motions, variables were tested with a programmable motion phantom and assessed. Patient traces were imported to a motion phantom and 4DCT and CBCT imaging were performed. Cos6 surrogate and sup-inf motion was also programmed into the phantom to simulate the long exhale of patients for image contrast tests. Results: Patient surrogate motion amplitudes were 9.9+5.2mm (3–35) at 18+6bpm (6–30). Expiration/Inspiration time ratios of 1.4+0.5second (0.6–2.9) showed image contrast effects evident in the AveCT and 3DCBCT images. Small differences were found for patients with multiple 4DCT data sets. Patient motion assessments were simulated and verified with the phantom within 2mm. Initial image reviews to check for reconstructed artefacts and data loss identified a small number of patients with irregularities in the automatic placement of inspiration and expiration points. Conclusion: The Physicist’s involvement in the continuous improvements of a clinically commissioned technique, processes and workflows continues beyond the commissioning stage of a project. Our experience with our clinical 4DCT program shows that Physics presence is required at the clinical 4DCT scan to assist with technical aspects of the scan and also for clinical image quality assessment prior to voluming. The results of this work enabled the sharing of information from the Medical Physics group with the Radiation Oncologists and Radiation Therapists. This results in an improved awareness of clinical patient respiration variables and how they may affect 4D simulation images and also may also affect the treatment verification images.

60 APPLIED LIFE SCIENCES↗

Exploring magnetized liner inertial fusion with a semi-analytic model

In this paper, we explore magnetized liner inertial fusion (MagLIF) [S. A. Slutz et al., Phys. Plasmas 17, 056303 (2010)] using a semi-analytic model [R. D. McBride and S. A. Slutz, Phys. Plasmas 22, 052708 (2015)]. Specifically, we present simulation results from this model that: (a) illustrate the parameter space, energetics, and overall system efficiencies of MagLIF; (b) demonstrate the dependence of radiative loss rates on the radial fraction of the fuel that is preheated; (c) explore some of the recent experimental results of the MagLIF program at Sandia National Laboratories [M. R. Gomez et al., Phys. Rev. Lett. 113, 155003 (2014)]; (d) highlight the experimental challenges presently facing the MagLIF program; and (e) demonstrate how increases to the preheat energy, fuel density, axial magnetic field, and drive current could affect future MagLIF performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗