Search NASA⌕ Search

SEARCH · Search NASA

Results for “DRAG REDUCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Thrust Removal Scheme for the FAST-MAC Circulation Control Model Tested in the National Transonic Facility

A second wind tunnel test of the FAST-MAC circulation control semi-span model was recently completed in the National Transonic Facility at the NASA Langley Research Center. The model allowed independent control of four circulation control plenums producing a high momentum jet from a blowing slot near the wing trailing edge that was directed over a 15% chord simple-hinged flap. The model was configured for transonic testing of the cruise configuration with 0deg flap deflection to determine the potential for drag reduction with the circulation control blowing. Encouraging results from analysis of wing surface pressures suggested that the circulation control blowing was effective in reducing the transonic drag on the configuration, however this could not be quantified until the thrust generated by the blowing slot was correctly removed from the force and moment balance data. This paper will present the thrust removal methodology used for the FAST-MAC circulation control model and describe the experimental measurements and techniques used to develop the methodology. A discussion on the impact to the force and moment data as a result of removing the thrust from the blowing slot will also be presented for the cruise configuration, where at some Mach and Reynolds number conditions, the thrust-removed corrected data showed that a drag reduction was realized as a consequence of the blowing.

Chan, David T.↗
NASA NTRS1977

Compliant wall surface motion and its effect on the structure of a turbulent boundary layer

The status of the continuing compliant wall drag reduction research at NASA-Langley Research Center is discussed. Preliminary surface motion calculations are reported along with compliant surface design concepts and their numerical models. A compliant drag reduction theory based on stabilizing the turbulent substructure is proposed and previous experiments have been examined relative to that theory. Results of recent low speed compliant surface experiments have been reported which include initial attempts to measure local compliant surface motion.

Ash, R. L.↗
NASA NTRS1999

Numerical Investigation of Flow Around Rectangular Cylinders with and Without Jets

The problem of flow past bluff bodies was studied extensively in the past. The problem of drag reduction is very important in many high speed flow applications. Considerable work has been done in this subject area in case of circular cylinders. The present study attempts to investigate the feasibility of drag reduction on a rectangular cylinder by flow injection by flow injection from the rear stagnation region. The physical problem is modeled as two-dimensional body and numerical analysis is carried out with and without trailing jets. A commercial code is used for this purpose. Unsteady computation is performed in case of rectangular cylinders with no trailing jets where as steady state computation is performed when jet is introduced. It is found that drag can be reduced by introducing jets with small intensity in rear stagnation region of the rectangular cylinders.

Tiwari, S. N .↗
NASA NTRS1990

Riblets

In addition to characterizing the various concepts reported in the literature on longitudinally-ribbed surface for aerodynamic surface drag reduction, the present development status evaluation of this technology correlates all available experimental data. An analysis of these data is then conducted to ascertain the parameters most directly involved in drag reduction, and to evaluate the effects which have thus far been exerted on turbulent boundary layer structures. Such advanced riblet techniques as compound and three-dimensional riblets, riblets in combination with large-eddy breakup devices, and riblets with suction/blowing, are also discussed.

Walsh, Michael J.↗
NASA NTRS1987

Direct drag and hot-wire measurements on thin-element riblet arrays

An experimental study of stream wise, near-wall, thin-element riblet arrays under a turbulent boundary layer has been conducted in low-speed air. Hot-wire data show that a single, isolated thin-element riblet causes formation of counter-rotating vortex-pairs with a spanwise wavelength of 130 viscous lengths. Abrupt shifts in turbulence intensity magnitude and peak location are observed for streamwise riblet arrays as spanwise riblet spacing is varied. Direct drag measurements show net drag reduction (up to 8.5 percent) over a wide range of riblet spacings along with behavior at discrete non-dimensional spacings indicative of vortex activity. Overall, the data suggest that more than one drag reduction mechanism may be involved.

Wilkinson, S. P.↗
NASA NTRS1989

On the active control of wall-bounded turbulent flows

The direct numerical simulation technique is used to explore concepts for manipulation of turbulent boundary layers. Significant drag reduction was achieved when at each instant the normal component of velocity at the wall was prescribed to be 180 deg out of phase with the normal velocity slightly above the wall. The drag reduction is accompanied with significant reduction in the intensity of the wall-layer structures and reductions in the magnitude of Reynolds stresses throughout the flow. Suitability of wall pressure and shear stress fluctuations for detection of flow structures above the wall are examined.

Moin, P.↗
NASA NTRS2012

Effects of Riblets on Skin Friction in High-Speed Turbulent Boundary Layers

Direct numerical simulations of spatially developing turbulent boundary layers over riblets are conducted to examine the effects of riblets on skin friction at supersonic speeds. Zero-pressure gradient boundary layers with an adiabatic wall, a Mach number of M1 = 2.5, and a Reynolds number based on momentum thickness of Re = 1720 are considered. Simulations are conducted for boundary-layer flows over a clean surface and symmetric V- groove riblets with nominal spacings of 20 and 40 wall units. The DNS results confirm the few existing experimental observations and show that a drag reduction of approximately 7% is achieved for riblets with proper spacing. The influence of riblets on turbulence statistics is analyzed in detail with an emphasis on identifying the differences, if any, between the drag reduction mechanisms for incompressible and high-speed boundary layers.

Duan, Lian↗
NASA NTRSDate not supplied

Aerodynamic Design Optimization for Natural Laminar Flow Airfoils

Natural laminar flow technology is a passive laminar flow control (LFC) strategy that seeks to delay the onset of boundary-layer transition (BLT) through shape optimization to reduce the drag of the aerodynamic vehicle. Adjoint-based design optimization for LFC is proposed in an integrated multidisciplinary framework, which includes the computational fluid dynamics (CFD), geometry and grid deformation, and linear stability analysis (LSA) for transition prediction. In particular, the BLT location is predicted using the dual N-factor method that is based on a linear stability theory (LST) eigenvalue problem. The dual N-factor criterion accounts for the amplification of planar Tollmien-Schlichting (TS) and stationary crossflow (CF) boundary-layer instabilities to predict the transition location in three-dimensional boundary-layer flows. The adjoint-based shape optimization procedure is based on an iteratively coupled CFD and LSA methodology to converge the transition location and flow solutions, as well as to calculate the sensitivities of the aerodynamic metrics of interest with respect to the flow and shape design parameters. The RAE 2822 airfoil at 0 and 30 degrees yaw angles, an angle of attack of 0.72 degrees, and subsonic conditions (M∞ = 0.19, Rec = 5.6 × 106 ) are used as baseline configurations for design optimization. The angle of attack and the vertical displacement of free-form-deformation control points are used as design variables to reduce the drag coefficient while reaching a specified lift coefficient. The optimized unswept airfoil designs achieve a 30% drag reduction accompanied by a downstream shift of the transition locations over both suction and pressure sides of the airfoil. The initial design iterations for the swept case also show a favorable trend in the drag reduction with transition delay over both sides.

Transition↗
NASA NTRS1992

Experiments and analysis concerning the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce transonic drag was investigated. A control volume analysis is developed and indicates that the specific impulse performance of external burning is competitive with other forms of airbreathing propulsion and depends on the fuel-air ratio, freestream Mach number, and the severity of the base drag. A method is presented for sizing fuel injectors for a desired fuel-air ratio in the unconfined stream. A two-dimensional Euler analysis is also presented which indicates that the total axial force generated by external burning depends on the total amount of energy input and is independent of the transverse and streamwise distribution of heat addition. Good agreement between the Euler and control volume analysis is demonstrated. Features of the inviscid external burning flowfield are discussed. Most notably, a strong compression forms at the sonic line within the burning stream which may induce separation of the plume and prevent realization of the full performance potential. An experimental program was conducted in a Mach 1.26 free-jet to demonstrate drag reduction on a simple expansion ramp geometry, and verify hydrogen-air stability limits at external burning conditions. Stable combustion appears feasible to Mach number of between 1.4 and 2 depending on the vehicle flight trajectory. Drag reduction is demonstrated on the expansion ramp at Mach 1.26; however, force levels showed little dependence on fuel pressure or altitude in contrast to control volume analysis predictions. Various facility interference mechanisms and scaling issues were studied and are discussed.

Trefny, Charles J.↗
NASA NTRS1988

A low-drag nose-body

In the present investigation of the application of convex-curvature viscous drag reduction to an axisymmetric body, the qualification of a modified mixing-length formulation in several complex two-dimensional and axisymmetric turbulent boundary layers that are primarily curved is followed by the design of a low-drag nose-body for low drag at high subsonic speeds. The longitudinal distribution of the cross-sectional area ratio is found to be critical to boundary layer separation, requiring implementation not over a single long span of curvature but over three short spans. The possibility of a 'net' drag reduction is examined in relation to 'equivalent' nose-bodies.

Bandyopadhyay, P. R.↗
NASA NTRS1986

Wall temperature control of low-speed body drag

The use of thermal means to control drag under turbulent boundary layer conditions is examined. Numerical calculations are presented for both skin friction and (unseparated) pressure drag for turbulent boundary-layer flows over a fuselage-like body with wall heat transfer. In addition, thermal control of separation on a bluff body is investigated. It is shown that a total drag reduction of up to 20 percent can be achieved for wall heating with a wall-to-total-freestream temperature ratio of 2. For streamlined slender bodies, partial wall heating of the forebody can produce almost the same order of total drag reduction as the full body heating case. For bluff bodies, the separation delay from partial wall cooling of the afterbody is approximately the same as for the fully cooled body.

Lin, J. C.↗
NASA NTRS1985

Investigation of the Vortex Tab

An investigation was made into the drag reduction capability of vortex tabs on delta wing vortex flaps. The vortex tab is an up-deflected leading edge portion of the vortex flap. Tab deflection augments vortex suction on the flap, thus improving its thrust, but the tab itself is drag producing. Whether a net improvement in the drag reduction can be obtained with vortex tabs, in comparison with plane vortex flaps of the same total area, was the objective of this investigation. Wind tunnel tests were conducted on two models, and analytical studies were performed on one of them using a free vortex sheet theory.

Hoffler, K. D.↗
NASA NTRS1958

A Body Modification to Reduce Drag Due to Wedge Angle of Wing with Unswept Trailing Edge

Ward's slender-body-theory formula for zero-lift drag contains three integrals plus a base-drag term. Two of these integral terms depend only upon the cross-sectional area distribution of the body. The third integral term depends only upon the body shape and axial slopes at the base of the body. This term is neglected in the transonic area rule because in many cases it is zero; however, there are also many cases in which it is not zero. This paper examines the term for the possibility of drag reduction for a particular case. The model considered consists of a body of revolution in combination with any wing that has an unswept trailing edge and a constant trailing-edge angle along its span. It is found that (neglecting any change in base drag) a drag reduction is obtainable which, for the case considered, is an additional 12 percent of that obtained with the area-rule modification. The probable effect of viscosity on this theoretical result is discussed.

Pitts, William C.↗
NASA NTRS1990

Wingtip vortex turbine investigation for vortex energy recovery

A flight test investigation has been conducted to determine the performance of wingtip vortex turbines and their effect on aircraft performance. The turbines were designed to recover part of the large energy loss (induced drag) caused by the wingtip vortex. The turbine, driven by the vortex flow, reduces the strength of the vortex, resulting in an associated induced drag reduction. A four-blade turbine was mounted on each wingtip of a single-engine, T-tail, general aviation airplane. Two sets of turbine blades were tested, one with a 15' twist (washin) and one with no twist. Th power recovered by the turbine and the installed drag increment were measured. A trade-off between turbine power and induced drag reduction was found to be a function of turbine blade incidence angle. This test has demonstrated that the wingtip vortex turbine is an attractive alternate, as well as an emergency, power source.

Abeyounis, William K.↗
NASA NTRS1993

Numerical simulation of non-Newtonian free shear flows

Free shear flows, like those of mixing layers, are encountered in aerodynamics, in the atmosphere, and in the ocean as well as in many industrial applications such as flow reactors or combustion chambers. It is, therefore, crucial to understand the mechanisms governing the process of transition to turbulence in order to predict and control the evolution of the flow. Delaying transition to turbulence as far downstream as possible allows a gain in energy expenditure while accelerating the transition can be of interest in processes where high mixing is desired. Various methods, including the use of polymer additives, can be effective in controlling fluid flows. The drag reduction obtained by the addition of small amounts of high polymers has been an active area of research for the last three decades. It is now widely believed that polymer additives can affect the stability of a large variety of flows and that dilute solutions of these polymers have been shown to produce drag reductions of over 80 percent in internal flows and over 60 percent in external flows under a wide range of conditions. The major thrust of this work is to study the effects of polymer additives on the stability of the incompressible mixing layer through large scale numerical simulations. In particular, we focus on the two dimensional flow and examine how the presence of viscoelasticity may affect the typical structures of the flow, namely roll-up and pairing of vortices.

Homsy, G. M.↗
NASA NTRS1981

Aircraft surface coatings for drag reduction/erosion protection

The laboratory testing of a large number of films and liquid coatings for aircraft drag reduction and erosion protection has led to the identification of elastomeric polyurethanes, which fulfil smoothness, durability and protection requirements while being easily applied to large, compound-curvature areas with standard spray equipment. It was found that an epoxy primer produced a stronger bond between coating and substrate than a wash primer. A drag-reduction value of 0.2% was achieved with a commercially-available elastomeric polyurethane.

Kreitinger, R. L.↗
NASA NTRS1990

Active turbulence control in wallbounded flow using direct numerical simulations

An exploratory study of concepts for active control of turbulent boundary layers using the direct numerical simulation technique was performed. Significant drag reduction was achieved when the surface boundary condition was modified such that it could suppress the large-scale structures present in the wall region. This was achieved by prescribing the normal component of velocity at the wall to be 180 deg out of phase with the normal velocity slightly above the wall at each instant. The drag reduction was accompanied with significant reduction in the intensity of the wall-layer structures and reductions in the magnitude of Reynolds stresses throughout the flow. Suitability of wall-pressure and shear-stress fluctuations for detection of flow structures above the wall was examined. A preliminary result obtained by applying the present control strategy to a transitional flow is also briefly described, from which one can infer a possible linkage between the control strategy and flow stability.

Kim, J.↗
NASA NTRSDate not supplied

Aerodynamic Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft with Variable-Camber Continuous Trailing-Edge Flap

This paper presents an aerodynamic optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with Variable-Camber Continuous Trailing-Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for three different VCCTEF configurations with 6-, 10-, and 21-spanwise sections, respectively. A simple VCCTEF actuator weight model is proposed to account the weight penalty of the actuator in the design. A vortex-lattice model of the TTBW model is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against wind tunnel test data. The optimization results show that the 21-spanwise sections VCCTEF has largest absolute drag coefficient reduction, however, the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to validate the VCCTEF optimization.

Aerodynamic Optimization↗