SEARCH · Search NASA

Results for “Design and modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

Investigation of problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars has been undertaken. Problem areas receiving attention include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis; terrain modeling and path selection; and chemical analysis of specimens. The following specific tasks have been under study: vehicle model design, mathematical modeling of a dynamic vehicle, experimental vehicle dynamics, obstacle negotiation, electromechanical controls, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer sybsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, chromatograph model evaluation and improvement.

Frederick, D. K.↗

NASA NTRS1993

The use of high fidelity CAD models as the basis for training on complex systems

During the design phases of large and complex systems such as NASA's Space Station Freedom (SSF), there are few, if any physical prototypes built. This is often due to their expense and the realization that the design is likely to change. This poses a problem for training, maintainability, and operations groups who are tasked to lay the foundation of plans for using these systems. The Virtual Reality and Visualization Laboratory at the Boeing Advanced Computing Group's Huntsville facility is supporting the use of high fidelity, detailed design models that are generated during the initial design phases, for use in training, maintainability and operations exercises. This capability was used in its non-immersive form to great effect at the SSF Critical Design Review (CDR) during February, 1993. Allowing the user to move about within a CAD design supports many efforts, including training and scenario study. We will demonstrate via a video of the Maintainability SSF CDR how this type of approach can be used and why it is so effective in conveying large amounts of information quickly and concisely. We will also demonstrate why high fidelity models are so important for this type of training system and how it's immersive aspects may be exploited as well.

Miller, Kellie↗

NASA NTRS2001

Field Model: An Object-Oriented Data Model for Fields

We present an extensible, object-oriented data model designed for field data entitled Field Model (FM). FM objects can represent a wide variety of fields, including fields of arbitrary dimension and node type. FM can also handle time-series data. FM achieves generality through carefully selected topological primitives and through an implementation that leverages the potential of templated C++. FM supports fields where the nodes values are paired with any cell type. Thus FM can represent data where the field nodes are paired with the vertices ("vertex-centered" data), fields where the nodes are paired with the D-dimensional cells in R(sup D) (often called "cell-centered" data), as well as fields where nodes are paired with edges or other cell types. FM is designed to effectively handle very large data sets; in particular FM employs a demand-driven evaluation strategy that works especially well with large field data. Finally, the interfaces developed for FM have the potential to effectively abstract field data based on adaptive meshes. We present initial results with a triangular adaptive grid in R(sup 2) and discuss how the same design abstractions would work equally well with other adaptive-grid variations, including meshes in R(sup 3).

Moran, Patrick J.↗

NASA NTRS1991

Flutter suppression via piezoelectric actuation

Experimental flutter results obtained from wind tunnel tests of a two degree of freedom wind tunnel model are presented for the open and closed loop systems. The wind tunnel model is a two degree of freedom system which is actuated by piezoelectric plates configured as bimorphs. The model design was based on finite element structural analyses and flutter analyses. A control law was designed based on a discrete system model; gain feedback of strain measurements was utilized in the control task. The results show a 21 pct. increase in the flutter speed.

Heeg, Jennifer↗

NASA NTRS2014

Thermal Vacuum Chamber Repressurization with Instrument Purging

At the conclusion of cryogenic vacuum testing of the James Webb Space Telescope Optical Telescope Element Integrated Science Instrument Module (JWST-OTIS) in NASA Johnson Space Center’s (JSCs) thermal vacuum (TV) Chamber A, contamination control (CC) engineers are postulating that chamber particulate material stirred up by the repressurization process may be kept from falling into the Integrated Science Instrument Module (ISIM) interior to some degree by activating instrument purge flows over some initial period before opening the chamber valves. This manuscript describes development of a series of models designed to describe this process. The models are strung together in tandem with a fictitious set of conditions to estimate overpressure evolution from which net outflow velocity behavior may be obtained. Creeping flow assumptions are then used to determine the maximum particle size that may be kept suspended above the ISIM aperture, keeping smaller particles from settling within the instrument module.

Repressurization↗

NASA NTRSDate not supplied

AI Foundation Models for Science: An Open Collaborative Initiative

Foundation Models (FMs), AI models designed to replace task-specific models, are increasingly being recognized for their versatility across numerous downstream applications. These models, trained using self-supervised techniques on any type of sequence data, circumvent the need for large annotated datasets, a major bottleneck in traditional AI model development. FMs can be applied to downstream tasks using few-shot learning and fine-tuning, significantly reducing the need for large labeled training datasets and computational resources. However, the development of FMs requires substantial resources, including access to data and compute power, expertise in the latest models, and specialized scientific knowledge for systematic evaluation. It is challenging for a single group to possess all these capabilities. To address this, NASA IMPACT has initiated an open collaborative effort, leveraging partnerships with the private sector and other groups within and outside NASA, to jointly build FMs. The overarching goal is to develop a consistent and collaborative approach to building FMs for high-value science datasets. This initiative has fostered collaboration within NASA and with external partners, including IBM Research, Clark University, DOE’s ORNL, ESA, and USGS. The effort focuses on identifying key datasets with a wide range of downstream applications, pretraining and building FMs using modified transformer architectures, evaluating compute infrastructure needs, and sharing models, pretraining and fine-tuning code, and data with the community. Furthermore, it aims to train the Earth science community to fine-tune these models for various downstream applications. Our initial effort resulted in the creation of a 100 million parameter HLS Geospatial Model within six months, which was released on HuggingFace. We are now expanding our scope to include data from weather and climate models and investigating multimodal models. We invite those interested in participating in this effort to join us by sharing their use cases, expertise, or data.

Rahul Ramachandran↗

NASA NTRSDate not supplied

Trajectory Planning and Online Performance Model Estimation for Advanced Air Mobility

We propose a framework for adaptive guidance based on optimal control and estimation using closed-loop performance models. In the proposed approach, parameters of a reduced-order performance model are estimated in real time so that trajectories and guidance commands are replanned with more accurate knowledge of the system's response and performance capabilities. To apply this methodology to flight control systems, we introduce a simple yet expressive performance model modified from a reference linear design model. The proposed framework is applied to guidance of a simulated Advanced Air Mobility class concept aircraft experiencing control effector failures. We demonstrate that, by optimizing performance model parameters in real time, guidance commands can be intelligently adjusted to recover system stability and the performance of a full-order vehicle model, even in the event of effector failures. Furthermore, the reduced-order performance model requires a fraction of the computational cost of the full-order model, facilitating real-time use of adaptive, optimal guidance.

Differential dynamic programming↗

NASA NTRSDate not supplied

Trajectory Planning and Online Performance Model Estimation for Advanced Air Mobility

Differential dynamic programming↗

NASA NTRS1990

Fuzzy compromise: An effective way to solve hierarchical design problems

In this paper, we present a method for modeling design problems using a compromise decision support problem (DSP) incorporating the principles embodied in fuzzy set theory. Specifically, the fuzzy compromise decision support problem is used to study hierarchical design problems. This approach has the advantage that although the system modeled has an element of uncertainty associated with it, the solution obtained is crisp and precise. The efficacy of incorporating fuzzy sets into the solution process is discussed in the context of results obtained for a portal frame.

Allen, J. K.↗

NASA NTRS2021

PEM Fuel Cell MODEL for Conceptual Design of Hydrogen eVTOL Aircraft

A model and software for design and analysis of a Proton Exchange Membrane fuel cell (PEMFC) system are developed for hydrogen eVTOL aircraft. Examples are provided of stacks designed for 80 kWe and 500 kWe net electrical power. Examples are provided of eVTOL designed for 250 and 400 lb payload. The trade-offs included stack characteristics, hydrogen storage characteristics, and aircraft payload and range. The objectives were to identify the key technology drivers of a hydrogen rotorcraft, establish technology targets for a viable aircraft, and recommend research to address the fundamental pre-competitive barriers. The current U.S. infrastructure on hydrogen informed the targets and recommendations. The key conclusion is that the advances made in cell electrochemical power density over the last decade might allow a PEMFC system to meet, or even beat, piston engine powered light-utility rotorcraft. The development must focus on the key drivers of a hydrogen eVTOL. The drivers are ultra-light stack cooling and short-term hydrogen storage. A stack system of net electrical power 100−150 kWe with specific power 1.1 kWe/kg including air, cooling, and electrical subsystems, and a tank storage of 15% weight fraction hydrogen are the minimum targets to meet the performance of a modern piston-engine rotorcraft, with a range of 180 nautical miles, payload of 400 lb, and gross weight of about 1400 lb. This is defined as the objective aircraft. If only one target is met, an aircraft of half the range could be produced, with a 30% greater gross take-off weight. This is defined as an intermediate aircraft. Because definitive conclusions are premature without weights and loads data on a flight-worthy stack system, it is recommended that a fuel cell powered hydrogen eVTOL demonstrator be built and flown. The existing hydrogen infrastructure for cars provide ample opportunity to create a pilot program. About 12 metric tons of retail hydrogen are available for cars every day in California, which is less than 0.05% of the yearly hydrogen production in the U.S.. A hypothetical fleet of 100 aircraft, operating 3 flights a day, would increase the demand by 2.25 tons per day and require 140 MWh of renewable electricity for green hydrogen.

PEM↗

NASA NTRS2004

Model-Based Engineering Design for Trade Space Exploration throughout the Design Cycle

This paper presents ongoing work to standardize model-based system engineering as a complement to point design development in the conceptual design phase of deep space missions. It summarizes two first steps towards practical application of this capability within the framework of concurrent engineering design teams and their customers. The first step is standard generation of system sensitivities models as the output of concurrent engineering design sessions, representing the local trade space around a point design. A review of the chosen model development process, and the results of three case study examples, demonstrate that a simple update to the concurrent engineering design process can easily capture sensitivities to key requirements. It can serve as a valuable tool to analyze design drivers and uncover breakpoints in the design. The second step is development of rough-order- of-magnitude, broad-range-of-validity design models for rapid exploration of the trade space, before selection of a point design. At least one case study demonstrated the feasibility to generate such models in a concurrent engineering session. The experiment indicated that such a capability could yield valid system-level conclusions for a trade space composed of understood elements. Ongoing efforts are assessing the practicality of developing end-to-end system-level design models for use before even convening the first concurrent engineering session, starting with modeling an end-to-end Mars architecture.

models↗

NASA NTRS1987

A stress index model for balloon design

A NASA stress index model, SINDEX, is discussed which establishes the relative stress magnitudes along a balloon gore as a function of altitude. Application of the model to a data base of over 550 ballon flights demonstrates the effectiveness of the method. The results show a strong correlation between stress levels, failure rates, and the point of maximum stress coinciding with the observed failure locations. It is suggested that the model may be used during the balloon design process to lower the levels of stress in the balloon.

Smith, I. S.↗

NASA NTRS1995

Dissipative rendering and neural network control system design

Model-based control system designs are limited by the accuracy of the models of the plant, plant uncertainty, and exogenous signals. Although better models can be obtained with system identification, the models and control designs still have limitations. One approach to reduce the dependency on particular models is to design a set of compensators that will guarantee robust stability to a set of plants. Optimization over the compensator parameters can then be used to get the desired performance. Conservativeness of this approach can be reduced by integrating fundamental properties of the plant models. This is the approach of dissipative control design. Dissipative control designs are based on several variations of the Passivity Theorem, which have been proven for nonlinear/linear and continuous-time/discrete-time systems. These theorems depend not on a specific model of a plant, but on its general dissipative properties. Dissipative control design has found wide applicability in flexible space structures and robotic systems that can be configured to be dissipative. Currently, there is ongoing research to improve the performance of dissipative control designs. For aircraft systems that are not dissipative active control may be used to make them dissipative and then a dissipative control design technique can be used. It is also possible that rendering a system dissipative and dissipative control design may be combined into one step. Furthermore, the transformation of a non-dissipative system to dissipative can be done robustly. One sequential design procedure for finite dimensional linear time-invariant systems has been developed. For nonlinear plants that cannot be controlled adequately with a single linear controller, model-based techniques have additional problems. Nonlinear system identification is still a research topic. Lacking analytical models for model-based design, artificial neural network algorithms have recently received considerable attention. Using their universal approximation property, neural networks have been introduced into nonlinear control designs in several ways. Unfortunately, little work has appeared that analyzes neural network control systems and establishes margins for stability and performance. One approach for this analysis is to set up neural network control systems in the framework presented above. For example, one neural network could be used to render a system to be dissipative, a second strictly dissipative neural network controller could be used to guarantee robust stability.

Gonzalez, Oscar R.↗

NASA NTRS1992

Simulator design for advanced ISDN satellite design and experiments

This simulation design task completion report documents the simulation techniques associated with the network models of both the Interim Service ISDN (integrated services digital network) Satellite (ISIS) and the Full Service ISDN Satellite (FSIS) architectures. The ISIS network model design represents satellite systems like the Advanced Communication Technology Satellite (ACTS) orbiting switch. The FSIS architecture, the ultimate aim of this element of the Satellite Communications Applications Research (SCAR) program, moves all control and switching functions on-board the next generation ISDN communication satellite. The technical and operational parameters for the advanced ISDN communications satellite design will be obtained from the simulation of ISIS and FSIS engineering software models for their major subsystems. Discrete events simulation experiments will be performed with these models using various traffic scenarios, design parameters and operational procedures. The data from these simulations will be used to determine the engineering parameters for the advanced ISDN communications satellite.

Pepin, Gerald R.↗

NASA NTRS1972

Development and optimization of a nonlinear multiparameter model for the human operator

A systematic method is proposed for the development, optimization, and comparison of controller-models for the human operator. This is suitable for any designed model, even multiparameter systems. A random search technique is chosen for the parameter optimization. As valuation criteria for the quality of the model development the criterion function - the comparison between the input and output functions of the human operator and those of the model - and the most important characteristic values and functions of the statistical signal theory are used. A nonlinear multiparameter model for the human operator is being designed which considers the complex input information rate per time in a single display. The nonlinear features of the model are effected by a modified threshold element and a decision algorithm. Different display-configurations as well as various transfer functions of the controlled element are explained by different optimized parameter-combinations.

Johannsen, G.↗

NASA NTRS1993

Grid sensitivity for aerodynamic optimization and flow analysis

After reviewing relevant literature, it is apparent that one aspect of aerodynamic sensitivity analysis, namely grid sensitivity, has not been investigated extensively. The grid sensitivity algorithms in most of these studies are based on structural design models. Such models, although sufficient for preliminary or conceptional design, are not acceptable for detailed design analysis. Careless grid sensitivity evaluations, would introduce gradient errors within the sensitivity module, therefore, infecting the overall optimization process. Development of an efficient and reliable grid sensitivity module with special emphasis on aerodynamic applications appear essential. The organization of this study is as follows. The physical and geometric representations of a typical model are derived in chapter 2. The grid generation algorithm and boundary grid distribution are developed in chapter 3. Chapter 4 discusses the theoretical formulation and aerodynamic sensitivity equation. The method of solution is provided in chapter 5. The results are presented and discussed in chapter 6. Finally, some concluding remarks are provided in chapter 7.

Sadrehaghighi, I.↗

NASA NTRS1983

Spectrophotovoltaic orbital power generation

A subscale model of a photovoltaic power system employing spectral splitting and 1000:1 concentration was fabricated and tested. The 10-in. aperture model demonstrated 15.5% efficiency with 86% of the energy produced by a GaAs solar cell and 14% of the energy produced by an Si cell. The calculated efficiency of the system using the same solar cells, but having perfect optics, would be approximately 20%. The model design, component measurements, test results, and mathematical model are presented.

Knowles, G.↗

NASA NTRS1989

Application of variable-gain output feedback for high-alpha control

This paper describes a variable-gain optimal discrete output-feedback design approach that is applied to a nonlinear flight regime covering a wide angle-of-attack range that includes stall and poststall. The paper includes brief descriptions of the variable-gain formulation, the discrete-control structure and flight equations used to apply the design approach, and the high performance airplane model used in the application. Both linear and nonlinear analyses are shown for a longitudinal four-model design case with angles of attack of 5, 15, 35, and 60 deg.

Ostroff, Aaron J.↗