Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation Lines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

The evolution with strain of the stored energy in different texture components of cold-rolled IF steel revealed by high resolution X-ray diffraction

During the deformation of low carbon steel by cold-rolling, dislocations are created and stored in grains depending on local crystallographic orientation, deformation, and deformation gradient. Orientation dependent dislocation densities have been estimated from the broadening of X-ray diffraction lines measured on a synchrotron beamline. Different cold-rolling levels (from 30% to 95% thickness reduction) have been considered. It is shown that the present measurements are consistent with the hypothesis of the sole consideration of screw dislocations for the analysis of the data. The presented evolutions show that the dislocation density first increases within the α fiber (=(hkl)<110>) and then within the γ fiber (=(111) ). A comparison with EBSD measurements is done and confirms that the storage of dislocations during the deformation process is orientation dependent and that this dependence is correlated to the cold-rolling level. If we assume that this dislocation density acts as a driving force during recrystallization, these observations can explain the fact that the recrystallization mechanisms are generally different after moderate or large strains. - Highlights: • Dislocation densities are assessed by XRD in main texture components of a steel sheet. • Dislocation densities vary with both strain and texture components. • The analysis relies on the sole presence of screw dislocations. • The measured dislocation densities include the contribution of both SSD and GND.

36 MATERIALS SCIENCE↗

Scaled free energies, power-law potentials, strain pseudospins, and quasiuniversality for first-order structural transitions

We consider ferroelastic first-order phase transitions with N{sub OP} order-parameter strains entering Landau free energies as invariant polynomials that have N{sub V} structural-variant Landau minima. The total free energy includes (seemingly innocuous) harmonic terms, in the n=6-N{sub OP} nonorder-parameter strains. Four three-dimensional (3D) transitions are considered, tetragonal/orthorhombic, cubic/tetragonal, cubic/trigonal, and cubic/orthorhombic unit-cell distortions, with, respectively, N{sub OP}=1, 2, 3, and 2; and N{sub V}=2, 3, 4, and 6. Five two-dimensional (2D) transitions are also considered, as simpler examples. Following Barsch and Krumhansl, we scale the free energy to absorb most material-dependent elastic coefficients into an overall prefactor, by scaling in an overall elastic energy density; a dimensionless temperature variable; and the spontaneous-strain magnitude at transition {lambda}<<1. To leading order in {lambda} the scaled Landau minima become material independent, in a kind of ''quasiuniversality.'' The scaled minima in N{sub OP}-dimensional order-parameter space, fall at the center and at the N{sub V} corners, of a transition-specific polyhedron inscribed in a sphere, whose radius is unity at transition. The ''polyhedra'' for the four 3D transitions are, respectively, a line, a triangle, a tetrahedron, and a hexagon. We minimize the n terms harmonic in the nonorder-parameter strains, by substituting solutions of the ''no dislocation'' St Venant compatibility constraints, and explicitly obtain power-law anisotropic, order-parameter interactions, for all transitions. In a reduced discrete-variable description, the competing minima of the Landau free energies induce unit-magnitude pseudospin vectors, with N{sub V}+1 values, pointing to the polyhedra corners and the (zero-value) center. The total scaled free energies then become Z{sub N{sub V+1}} clocklike pseudospin Hamiltonians, with temperature-dependent local Landau terms, nearest-neighbor Ginzburg couplings, and power-law St Venant interactions that drive the elastic domain-wall texturing. The scaled free energies can be used in relaxational or underdamped dynamic simulations to study ferroelastic strain textures and their dynamical evolution pathways. The pseudospin models can similarly be studied via local meanfield treatments and Monte Carlo simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quantitative description of microstructure defects in hexagonal boron nitrides using X-ray diffraction analysis

A routine for simultaneous quantification of turbostratic disorder, amount of puckering and the dislocation and stacking fault density in hexagonal materials was proposed and tested on boron nitride powder samples that were synthesised using different methods. The routine allows the individual microstructure defects to be recognised according to their effect on the anisotropy of the X-ray diffraction line broadening. For quantification of the microstructure defects, the total line broadening is regarded as a linear combination of the contributions from the particular defects. The total line broadening is obtained from the line profile fitting. As testing material, graphitic boron nitride (h-BN) was employed in the form of hot-isostatically pressed h-BN, pyrolytic h-BN or a h-BN, which was chemically vapour deposited at a low temperature. The kind of the dominant microstructure defects determined from the broadening of the X-ray diffraction lines was verified by high resolution transmission electron microscopy. Their amount was attempted to be verified by alternative methods. - Highlights: • Reliable method for quantification of microstructure defects in BN was suggested. • The method is based on the analysis of anisotropic XRD line broadening. • This XRD line broadening is unique and characteristic of the respective defect. • Thus, the quantification of coexistent microstructure defects is possible. • The method was tested on hexagonal BN, which was produced by different techniques.

36 MATERIALS SCIENCE↗

Damping mechanisms in alumina borate whisker-reinforced-aluminum matrix composites with or without SnO{sub 2} coatings

SnO{sub 2} was successfully coated on the surface of alumina borate whiskers. The pure aluminum matrix composites reinforced with a SnO{sub 2}-coated alumina borate whisker were fabricated by squeeze casting. The effects of coating contents on the damping properties of the coated composites at various temperatures, frequencies, and strain amplitudes were examined. The microstructures of the coated composites were also investigated through transmission electron microscopy observations. These results indicate that the introduction of Sn at the interface between whisker and matrix in the coated composites during the squeeze casting process alters not only the interface structures but also the dislocation status of the matrices in the vicinity of the interface. The results of damping characterization indicate that the damping capacities of the coated composites strongly depend on the coating contents and strain amplitudes. A damping peak at low temperatures appeared not only in the coated composites but also in the noncoated one, which is related to dislocation motion and interfacial slip caused by Sn. A damping peak at high temperatures appeared only in the coated composites, and the damping mechanisms at high temperature change with the increase in strain amplitudes. Sn played an important role on the damping mechanisms of the coated composites all along.

36 MATERIALS SCIENCE↗

Direct evidence of single quantum dot emission from GaN islands formed at threading dislocations using nanoscale cathodoluminescence: A source of single photons in the ultraviolet

Intense emission from GaN islands embedded in AlN resulting from GaN/AlN quantum well growth is directly resolved by performing cathodoluminescence spectroscopy in a scanning transmission electron microscope. Line widths down to 440 μeV are measured in a wavelength region between 220 and 310 nm confirming quantum dot like electronic properties in the islands. These quantum dot states can be structurally correlated to islands of slightly enlarged thicknesses of the GaN/AlN quantum well layer preferentially formed in vicinity to dislocations. The quantum dot states exhibit single photon emission in Hanbury Brown-Twiss experiments with a clear antibunching in the second order correlation function at zero time delay.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High temperature annealing of ion irradiated tungsten

In this study, transmission electron microscopy of high temperature annealing of pure tungsten irradiated by self-ions was conducted to elucidate microstructural and defect evolution in temperature ranges relevant to fusion reactor applications (500–1200°C). Bulk isochronal and isothermal annealing of ion irradiated pure tungsten (2 MeV W + ions, 500°C, 1014 W + /cm 2 ) with temperatures of 800, 950, 1100 and 1400°C, from 0.5 to 8 h, was followed by ex situ characterization of defect size, number density, Burgers vector and nature. Loops with diameters larger than 2–3 nm were considered for detailed analysis, among which all loops had View the MathML source and were predominantly of interstitial nature. In situ annealing experiments from 300 up to 1200°C were also carried out, including dynamic temperature ramp-ups. These confirmed an acceleration of loop loss above 900°C. At different temperatures within this range, dislocations exhibited behaviour such as initial isolated loop hopping followed by large-scale rearrangements into loop chains, coalescence and finally line–loop interactions and widespread absorption by free-surfaces at increasing temperatures. An activation energy for the annealing of dislocation length was obtained, finding E a =1.34±0.2 eV for the 700–1100°C range.

36 MATERIALS SCIENCE↗

Shear-Coupled Grain Growth and Texture Development in a Nanocrystalline Ni-Fe Alloy during Cold Rolling

The evolution of texture, grain size, grain shape, dislocation and twin density has been determined by synchrotron X-ray diffraction and line profile analysis in a nanocrystalline Ni- Fe alloy after cold rolling along different directions related to the initial fiber and the long axis of grains. The texture evolution has been simulated by the Taylor-type relaxed constraints viscoplastic polycrystal model. The simulations were based on the activity of partial dislocations in correlation with the experimental results of dislocation density determination. The concept of stress-induced shear-coupling is supported and strengthened by both the texture simulations and the experimentally determined evolution of the microstructure parameters. Grain-growth and texture evolution are shown to proceed by the shear-coupling mechanism supported by dislocation activity as long as the grain size is not smaller than about 20 nm.

Dislocation mechanism of grain growth↗

Phase-Specific Elastic/Plastic Interface Interactions in Layered Cr-NiAl Structures

The depth-dependent, as-grown and deformation-induced strain and dislocations partitioned through the interfaces in a two-phase layered NiAl-Cr(Mo) structure are directly measured at the mesoscale using 3-D X-ray microdiffraction. It is demonstrated that in the as-grown, undeformed state, neighboring submicron Cr solid solution and NiAl eutectic lamellae (doped with {approx}3% Mo) form a heterointerface with 180{sup o} rotation around a <1 1 2> pole. It is shown that the mechanical response to the indentation of a layered composite with alternating Cr(Mo)-NiAl lamellae is distinct from the response of single-phase materials. In the center of the indent, after the load is released, the NiAl lamellae are under compressive forward stresses (with the same sign as the indentation-induced compression) while Cr solid solution lamellae are under tensile back stresses (with opposite sign from the indentation load). The depth-dependent alternation of compressive/tensile residual strains in the neighboring Cr solid solution and NiAl lamellae is understood in the framework of the Mughrabi's composite model considering two types of structure elements: harder and softer regions. Under indentation, both kinds of lamellae are assumed to deform compatibly. After the load is released, residual forward stresses are formed in the harder lamellae, and back stresses are formed in the mechanically softer lamellae. Line-broadening analysis of the intensity distribution along the diffraction vector reveals a 15-times increase in dislocation density in the near-surface zone in the center of the indent. Such a large increase is typical for severe deformation.

36 MATERIALS SCIENCE↗

A multi-scale model of dislocation plasticity in α-Fe: Incorporating temperature, strain rate and non-Schmid effects

In this study, we develop an atomistically informed crystal plasticity finite element (CP-FE) model for body-centered-cubic (BCC) α-Fe that incorporates non-Schmid stress dependent slip with temperature and strain rate effects. Based on recent insights obtained from atomistic simulations, we propose a new constitutive model that combines a generalized non-Schmid yield law with aspects from a line tension (LT) model for describing activation enthalpy required for the motion of dislocation kinks. Atomistic calculations are conducted to quantify the non-Schmid effects while both experimental data and atomistic simulations are used to assess the temperature and strain rate effects. The parameterized constitutive equation is implemented into a BCC CP-FE model to simulate plastic deformation of single and polycrystalline Fe which is compared with experimental data from the literature. This direct comparison demonstrates that the atomistically informed model accurately captures the effects of crystal orientation, temperature and strain rate on the flow behavior of siangle crystal Fe. Furthermore, our proposed CP-FE model exhibits temperature and strain rate dependent flow and yield surfaces in polycrystalline Fe that deviate from conventional CP-FE models based on Schmid's law.

36 MATERIALS SCIENCE↗

Slip band characteristics in the presence of grain boundaries in nickel-based superalloy

Shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m’-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

36 MATERIALS SCIENCE↗

Dislocation Dynamics Simulations of Junctions in Hexagonal Close-Packed Crystals

The formation and strength of dislocations in the hexagonal closed packed material beryllium are studied through dislocation junctions and the critical stress required to break them. Dislocation dynamics calculations (using the code ParaDiS) of junction maps are compared to an analytical line tension approximation in order to validate our model. Results show that the two models agree very well. Also the critical shear stress necessary to break 30{sup o} - 30{sup o} and 30{sup o} - 90{sup o} dislocation junctions is computed numerically. Yield surfaces are mapped out for these junctions to describe their stability regions as function of resolved shear stresses on the glide planes. The example of two non-coplanar binary dislocation junctions with slip planes [2-1-10] (01-10) and [-12-10] (0001) corresponding to a prismatic and basal slip respectively is chosen to verify and validate our implementation.

36 MATERIALS SCIENCE↗

Enhancement of room temperature dislocation-related photoluminescence of electron irradiated silicon

In this paper, we have investigated the room temperature dislocation-related photoluminescence of electron irradiated silicon. It is found that high temperature annealing can enhance the D1 line emission measured at room temperature. The abnormal peak shift of D1 line on the dependence of temperatures reveals the reconstruction of D1 luminescence center. It is suggested that the high temperature annealing could cause the transformation of the dislocation-point defect structure, so that the D1 luminescence is enhanced and stabilized.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Detector performance and defect densities in CdZnTe after two-step annealing

Defects both micro-scale and nano-scale are plays an important role in CdZnTe(CZT) device performance. Typical micro-scale defect, Te inclusions, was removed by two-step annealing and its concentration were analyzed by IR transmission microscopy. In addition, transmission electron microscopy (TEM) measurement was employed to investigate the evolution of nano-scale defects after annealing process. Micro-twins and stacking faults were commonly observed defects in CZT as-grown and annealed CZT. The line shape defects which possibly related to the stress field around dislocations, were combine and disappear in in-situ the annealing at 200-220 °C. Frisch-grid CZT detector made of two-step annealed one exhibit better energy resolution and low backscattering counts in Cs-137 gamma spectra.

36 MATERIALS SCIENCE↗

Characterizing dislocation configurations and their evolution during creep of a new 12% Cr steel

Highlights: • Applicability of different techniques to characterize particular dislocation configuration. • XRD models in combination with TEM and EBSD to measure the dislocation density. • Substructure evolution during creep of a new 12% Cr steel is discussed. - Abstract: In this research, different types of dislocations are characterized and quantified in a newly developed 12% Cr steel in as-received as well as in crept conditions. X-ray diffraction (XRD) patterns are analyzed using three different models. The dislocation densities are determined employing the Convolution Multiple Whole Profile (CMWP) fitting, the analysis of the asymptotic part of the X-ray line profile (Groma's method), and the Rietveld refinement coupling Popa's and Williamson-Smallman approaches. CMWP method is used to measure the internal dislocation density inside the subgrains consisting of mobile and dipole dislocations, and the results show good agreement with Transmission Electron Microscopy (TEM) measurements. Groma's method is used to evaluate the total dislocation density, with results comparable to those obtained from the combination of Electron Backscatter Diffraction (EBSD) and TEM. Rietveld method gives the internal dislocation density or mobile dislocation density depending on the model chosen. The experimentally determined results such as creep strain, dislocation densities and subgrain size are compared with theoretical predictions and they are found in good agreement.

36 MATERIALS SCIENCE↗

Corrosion Behaviour of Ni{sub 78}Si{sub 8}B{sub 14} Alloy in 1 M NaCl Aqueous Medium at Room Temperature

Potentiodynamic polarization studies were performed on the air side and wheel side of the specimen Ni{sub 78}Si{sub 8}B{sub 14} in 1 M NaCl aqueous medium at room temperature. It was observed that the corrosion current density on the air side of the specimen was less than that of the wheel side of the specimen in 1 M NaCl aqueous medium. The amorphous nature of the air side and wheel side of the specimen Ni{sub 78}Si{sub 8}B{sub 14} was confirmed by X-ray diffraction (XRD). The observed behaviour can be related to the surface morphology due to processing of the ribbons. It is suggested that the inferior corrosion resistance of the wheel side surface is attributed to higher concentration of quenched-in defects due to higher cooling rate. Weight loss studies were also carried out in order to corroborate the polarization results. The results are discussed in the paper in the light of data reported in the literature.

36 MATERIALS SCIENCE↗