Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Two-phase flow numerical analysis of electrode geometry for alkaline water electrolyzers

Hydrogen is a promising component of a future energy-secure and efficient economy, but its competitiveness depends on reducing production costs. One strategy is to operate alkaline water electrolyzers at higher current densities to increase output. However, this intensifies performance losses due to gas bubble accumulation, which blocks transport pathways and deactivates electrochemically active surfaces. Enhancing bubble evacuation through electrode design is therefore essential. Previous studies have explored various approaches — such as modifying surface morphology, applying sonication or pressure modulation, and introducing surfactants — but these efforts have addressed a limited range of conditions due to the complexity of two-phase flow and electrode geometries. Experiments have also largely been focused on either cell level improvements, which lack the information necessary to isolate each contributing factor, or on modified geometries that are not relevant to practical cell operation. From a modeling perspective, conventional Eulerian multiphase models do not track the complex gas–liquid interfacial dynamics and often neglect surface tension and contact angle effects, reducing their predictive accuracy. To provide insights on the effects of different electrode geometries on the performance of alklaine water electrolyzers this work employs an immersed boundary volume-of-fluid method to simulate bubble behavior in 3D porous electrodes. Multiple base electrode geometries, typically used in practice, with varying porosity are evaluated under a constant surface gas generation rate. Simulation data is analyzed to quantify electrode gas coverage, bubble size dynamics and other relevant metrics. Results show that porosity strongly influences bubble accumulation on electrode surfaces, with higher porosity reducing gas coverage, and its not strictly dependent on the electrode geometry. However, the electrode’s base geometry significantly affects gas accumulation at the separator gap, independent of porosity. A foam electrode geometry resulted in the lowest gas coverage of all electrodes with a median volumetric gas coverage of 11%, but at the cost of a 70% reduction in active area compared with the largest surface area electrode, while gyroid electrodes showed the best trade-off between gas coverage, particularly at the separator surface, and electrochemically active area. In conclusion, the results highlight the need for holistic electrode design strategies.

Alkaline↗
NASA NTRSDate not supplied

Retrospectives: Current State of Knowledge on the Intersection of Spaceflight Stressors and Microbial Risks to Crew and Craft

OVERVIEW The spaceflight environment has several unique stressors that affect the health of both the crew and the spacecraft. An area of continued, albeit incomplete, study is the interaction of these stressors on microbial populations inherent to both astronauts and spacecraft surfaces and systems. A primary concern is the potential for the spaceflight environment to perturb the phenotype of these populations towards negative outcomes for crew and craft. In order to effectively mitigate these potential risks, they must first be characterized. We performed a retrospective literature analysis to assess the current state of knowledge regarding the affects of ionizing radiation and elevated CO2 on relevant microbial populations. The results of these retrospectives will guide next steps in the decisions of what (if any) further studies should be pursued and to guide decisions of the need for countermeasures. STRESSORS Ionizing radiation. The health risk involved with increased exposure to cosmic radiation has been studied in crew for 35+ years, with human health and cancer risk being the main focus. However, space radiation could also affect both the resident microorganisms aboard the ISS and the normal, healthy astronaut microbiomes that are of direct concern for crew health. A retrospective review of over 250 publications was accomplished looking at the impact of cumulative ionizing radiation doses lower than 3 Gy (chronic or acute) on microbial populations. Elevated CO2. The health risk involved with elevated atmospheric CO2 in spacecraft, primarily focusing on human toxicological risks, is understudied. The current Spaceflight Maximum Allowance Concentration for 24-hour average CO2 is 0.4% (3 mm Hg), which is significantly higher than terrestrial levels (0.04%). Whether these elevated ambient CO2 levels aboard spacecraft influence the diversity and phenotypic responses of the resident microbial communities from both the spacecraft environment (air, surface, water) and crew members (gut, nasal, skin microbiomes) is not known. A retrospective review was accomplished looking at the impact of chronic CO2 exposure up to 0.7% (5 mm Hg) for up to 6 months and acute exposure up to 2.6% (20 mm Hg) for up to 24 hours. CONCLUSIONS: MICROBIOME OF THE BUILT ENVIRONMENT The microbiome of the built spacecraft environment has been sampled consistently over the course of human spaceflight and significant advancements have been made in identifying microbial populations on the ISS. The dominant source of microbes on spacecraft surfaces are human-derived. Once in the spacecraft built environment, the extreme environment selects for features that enhance survival. While efforts to understand potential antibiotic resistance and pathogenicity of ISS isolates is robust, there is little to no understanding of which spaceflight environmental stressors, to include ionizing radiation or elevated CO2, drive the evolutionary trajectory of spacecraft-associated microbial populations. CONCLUSIONS: MICROBE-HOST INTERACTIONS The host-microbiome field has emerged as an important factor in human health on Earth as well in spaceflight. The field is struggling with the complexity of the system under investigation as there is substantial taxonomic and functional heterogeneity in these communities, making it difficult to establish clear stimulus-response dynamics. Taxonomic characterization is the norm; however, the functional role of each community member is key to linking environmental perturbations to potential dysbiosis. For both ionizing radiation and elevated CO2, the likely target of the perturbation is the host tissue, not the microbes themselves.. Any resulting changes to the microbial community composition and/or function is likely a result of adapting to those changes in the host physiology. RECOMMENDATIONS Emphasize functional characterization as opposed to taxonomic characterization of microbial communities. Increase the number of investigations using chronic, spaceflight-relevant doses of ionizing radiation. MoBE studies should move away from observational studies towards predictive modeling of community dynamics. Continue to develop scale-down models, such as tissues-on-a-chip & defined microbial communities. Focus on the crew response to elevated CO2 over MoBE considerations. Assess how direct contact with the hypercapnic environment affects skin microbiome dynamics.

retrospective↗
NASA NTRSDate not supplied

Retrospectives: Intersection of Spaceflight Stressors and Microbial Risk to Crew and Craft

OVERVIEW The spaceflight environment has several unique stressors that affect the health of both the crew and the spacecraft. An area of continued, albeit incomplete, study is the interaction of these stressors on microbial populations inherent to both astronauts and spacecraft surfaces and systems. A primary concern is the potential for the spaceflight environment to perturb the phenotype of these populations towards negative outcomes for crew and craft. In order to effectively mitigate these potential risks, they must first be characterized. We performed a retrospective literature analysis to assess the current state of knowledge regarding the affects of ionizing radiation and elevated CO2 on relevant microbial populations. The results of these retrospectives will guide next steps in the decisions of what (if any) further studies should be pursued and to guide decisions of the need for countermeasures. STRESSORS Ionizing radiation. The health risk involved with increased exposure to cosmic radiation has been studied in crew for 35+ years, with human health and cancer risk being the main focus. However, space radiation could also affect both the resident microorganisms aboard the ISS and the normal, healthy astronaut microbiomes that are of direct concern for crew health. A retrospective review of over 250 publications was accomplished looking at the impact of cumulative ionizing radiation doses lower than 3 Gy (chronic or acute) on microbial populations. Elevated CO2. The health risk involved with elevated atmospheric CO2 in spacecraft, primarily focusing on human toxicological risks, is understudied. The current Spaceflight Maximum Allowance Concentration for 24-hour average CO2 is 0.4% (3 mm Hg), which is significantly higher than terrestrial levels (0.04%). Whether these elevated ambient CO2 levels aboard spacecraft influence the diversity and phenotypic responses of the resident microbial communities from both the spacecraft environment (air, surface, water) and crew members (gut, nasal,skin microbiomes) is not known. A retrospective review was accomplished looking at the impact of chronic CO2 exposure up to 0.7% (5 mm Hg) for up to 6 months and acute exposure up to 2.6% (20 mm Hg) for up to 24 hours. CONCLUSIONS: MICROBIOME OF THE BUILT ENVIRONMENT The microbiome of the built spacecraft environment has been sampled consistently over the course of human spaceflight and significant advancements have been made in identifying microbial populations on the ISS. The dominant source of microbes on spacecraft surfaces are human-derived. Once in the spacecraft built environment,the extreme environment selects for features that enhance survival. While efforts to understand potential antibiotic resistance and pathogenicity of ISS isolates is robust, there is little to no understanding of which spaceflight environmental stressors, to include ionizing radiation or elevated CO2, drive the evolutionary trajectory of spacecraft-associated microbial populations. CONCLUSIONS: MICROBE-HOST INTERACTIONS The host-microbiome field has emerged as an important factor in human health on Earth as well in spaceflight. The field is struggling with the complexity of the system under investigation as there is substantial taxonomic and functional heterogeneity in these communities, making it difficult to establish clear stimulus-response dynamics.Taxonomic characterization is the norm; however, the functional role of each community member is key to linking environmental perturbations to potential dysbiosis. For both ionizing radiation and elevated CO2, the likely target of the perturbation is the host tissue, not the microbes themselves.. Any resulting changes to the microbial community composition and/or function is likely a result of adapting to those changes in the host physiology. RECOMMENDATIONS Emphasize functional characterization as opposed to taxonomic characterization of microbial communities.Increase the number of investigations using chronic, spaceflight-relevant doses of ionizing radiation. MoBE studies should move away from observational studies towards predictive modeling of community dynamics. Continue to develop scale-down models, such as tissues-on-a-chip & defined microbial communities. Focus on the crew response to elevated CO2 over MoBE considerations. Assess how direct contact with the hypercapnic environment affects skin microbiome dynamics.

Countermeasures↗
DOE OSTI2020

Sudden-Discharge Cycling Characteristics and Millisecond Dynamic Behaviors of a HTS Stainless-Steel Insulated Double-Pancake Coil With Thin Copper Plates

We have tested an intermediate-sized HTS stainless-steel (co-wound) insulated double pancake coil (~132 turns per coil) and discovered dynamic effects during sudden discharge on both millisecond and second scales. For soft break, the power supply is turned off suddenly but the shunt resistor (164 milliohm) is still connected; for hard break, a high voltage contactor is used to suddenly open the circuit so that the leads are completely open. Hard break is dangerous to traditionally insulated LTS magnets, but the SS-insulated HTS DPC retained integrity over ¡80 charge-discharge cycles. Voltage decay curves for soft and hard breaks are studied on short and long timescales. On long timescales, we observe the expected exponential decay and measure the time constant to calculate contact resistance. On short timescales, we observe highly dynamic effects: a hyper-exponential decay suggesting that the inductance or contact resistance is suddenly changing with time, likely an indication of the RL circuit forming. Moreover, peak voltage immediately (ms) after the sudden discharge were collected and compared. It is found that the peak voltage in soft-discharge is proportional to the applied current, while the those in hard-break has a unique pattern and tends to stay flat even though the applied current increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Sierra/SolidMechanics 5.0 Goodyear Specific

Sierra/SolidMechanics (Sierra/SM) is a Lagrangian, three-dimensional finite element analysis code for solids and structures subjected to extensive contact and large deformations, encompassing explicit and implicit dynamic as well as quasistatic loading regimes. This document supplements the primary Sierra/SM 5.0 User’s Guide, describing capabilities specific to Goodyear analysis use cases, including additional implicit solver options, material models, finite element formulations, and contact settings.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Sierra/SolidMechanics 4.56 Goodyear User's Guide

Sierra/SolidMechanics (Sierra/SM) is a Lagrangian, three-dimensional finite element analysis code for solids and structures subjected to extensive contact and large deformations, encompassing explicit and implicit dynamic as well as quasistatic loading regimes. This document supplements the primary Sierra/SM 4.56 User’s Guide, describing capabilities specific to Goodyear analysis use cases, including additional implicit solver options, material models, finite element formulations, and contact settings.

42 ENGINEERING↗
DOE OSTI2022

Spin-piston problem for a ferromagnetic thin film: Shock waves and solitons

In this report the unsteady, nonlinear magnetization dynamics induced by spin injection in an easy-plane ferromagnetic channel subject to an external magnetic field are studied analytically. Leveraging a dispersive hydrodynamic description, the Landau-Lifshitz equation is recast in terms of hydrodynamic-like variables for the magnetization's perpendicular component (spin density) and azimuthal phase gradient (fluid velocity). Spin injection acts as a moving piston that generates nonlinear, dynamical spin textures in the ferromagnetic channel with downstream quiescent spin density set by the external field. In contrast to the classical problem of a piston accelerating a compressible gas, here, variable spin injection and field lead to a rich variety of nonlinear wave phenomena from oscillatory spin shocks to solitons and rarefaction (expansion) waves. A full classification of solutions is provided using nonlinear wave modulation theory by identifying two key aspects of the fluid-like dynamics: subsonic/supersonic conditions and convex/nonconvex hydrodynamic flux. Familiar waveforms from the classical piston problem such as rarefaction waves and shocks manifest in their spin-based counterparts as smooth and highly oscillatory transitions, respectively, between two distinct magnetic states. The spin shock is an example of a dispersive shock wave, which arises in many physical systems. New features without a gas dynamics counterpart include composite wave complexes with “contact” spin shocks and rarefactions. Magnetic supersonic conditions lead to two pronounced piston edge behaviors including a stationary soliton and an oscillatory wave train. These coherent wave structures have physical implications for the generation of high frequency spin waves from pulsed injection and persistent, stable stationary and/or propagating solitons in the presence of magnetic damping. The analytical results are favorably compared with numerical simulations.

36 MATERIALS SCIENCE↗
NASA NTRS2012

SRMS Assisted Docking and Undocking for the Orbiter Repair Maneuver

As part of the Orbiter Repair Maneuver (ORM) planned for Return to Flight (RTF) operations, the Shuttle Remote Manipulator System (SRMS) must undock the Orbiter, maneuver it through a complex trajectory at extremely low rates, present it to an EVA crewman at the end of the Space Station Remote Manipulator System to perform the Thermal Protection System (TPS) repair, and then retrace back through the trajectory to dock the Orbiter with the Orbiter Docking System (ODS). The initial and final segments of this operation involve the interaction between the SRMS, ISS, Orbiter and ODS. Previously, a technique entitled "SRMS assisted docking" for installation of a payload to the ODS had been developed and was utilized for the Russian provided Docking Module on STS-74 during Shuttle-Mir missions and both the Node 1 and FGB elements on STS-88/Flight 2A. This procedure consisted of the SRMS grappling the respective payload, maneuvering it to a pre-install position inches above the ODS Androgynous Peripheral Attachment System (APAS) ring, commanding the SRMS into Test mode (which allows brakes-off motion of the joints), and then down-firing Primary Reaction Control System (PRCS) jets in order to effect a capture of the APAS latches. Once a successful capture had been achieved, then the AP AS was operated through its nominal retraction sequence to complete the mating sequence. While this technique can once again be used for the tail end docking portion of the ORM, the initial undocking of the orbiter and ISS vehicles with the assistance of the SRMS has yet to be attempted on orbit. The objective here is to determine the most efficient means to separate or extract the vehicles. Two techniques were analyzed in support of RTF: (1) the 'nominal' demating from the mated interface, and (2) the SRMS performing the operation (either in an active or passive fashion). In the first operation, the demating process would replicate standard undocking operations, with the exception that the SRMS is allowed to arrest the resulting motion. The second operation would be to extend the APAS ring to a ready to dock position, open the capture latches, and then detach the vehicles using the SRMS either actively or passively. In the active case, the APAS ring is extended and latched, and the SRMS is commanded to pull the two interfaces apart (assuming that the effective pull force of the SRMS can overcome the spec values of the combined latch resistance). In the passive case, the SRMS brakes are engaged and the AP AS mechanism is commanded to retract, pulling the two interfaces apart. Since the emphasis of both STS-74 and STS-88 had solely been on the installation operation, as opposed to the separation operation, two new models required development and incorporation within simulation tools designed to analyze those scenarios. These enhancements included: (1) a detailed demating dynamics model to characterize the pusher spring characteristics during undocking, and (2) contact and mechanical system modeling of the back side of the latches to represent unlatching dynamics. This paper first provides an overview of the Monte-Carlo screening analysis for the installation (both nominal and contingency), including the variation of separation distance, misalignment conditions, SRMS joint/brake parameter characteristics, and PRCS jet combinations and corresponding thrust durations. The resulting 'optimum' solution is presented based on trade studies between predicted capture success and integrated system loads. This paper then discusses the upgrades to the APAS math model associated with the new SRMS assisted undocking technique and reviews simulation results for various options investigated for either the active and passive separation of the ISS from the Orbiter.

Space Station Remote Manipulator System↗
NASA NTRS1984

Lubrication of Machine Elements

The understanding of hydrodynamic lubrication began with the classical experiments of Tower and Petrov. Reynolds used a reduced form of the Navier-Stokes equations and the continuity equation to generate a second order differential equation for the pressure in the narrow, converging gap of a bearing contact. Such a pressure enables a load to be transmitted between the surfaces with very low friction since the surfaces are completely separated by a film of fluid. In such a situation it is the physical properties of the lubricant, notably the dynamic viscosity, that dictate the behavior of the contact. The understanding of boundary lubrication is normally attributed to Hardy and Doubleday. In boundary lubrication it is the physical and chemical properties of thin films of molecular proportions and the surfaces to which they are attached that determine contact behavior. The lubricant viscosity is not an influential parameter. Research is devoted to a better understanding and more precise definition of other lubrication regimes between these extremes. One such regime, elastohydrodynamic lubrication, occurs in nonconformal contacts, where the pressures are high and the bearing surfaces deform elastically. In this situation the viscosity of the lubricant may raise considerably, and this further assists the formation of an effective fluid film. The science of these three lubrication regimes (hydrodynamic, elastohydrodynamic, and boundary) are described and the manner in which this science is used in the design of machine elements is examined.

Hamrock, Bernard J.↗
DOE OSTI2021

Molecular chaperone RAP interacts with LRP1 in a dynamic bivalent mode and enhances folding of ligand-binding regions of other LDLR family receptors

The low-density lipoprotein receptor (LDLR) family of receptors are cell-surface receptors that internalize numerous ligands and play crucial role in various processes, such as lipoprotein metabolism, hemostasis, fetal development, etc. Previously, receptor-associated protein (RAP) was described as a molecular chaperone for LDLR-related protein 1 (LRP1), a prominent member of the LDLR family. We aimed to verify this role of RAP for LRP1 and two other LDLR family receptors, LDLR and vLDLR, and to investigate the mechanisms of respective interactions using a cell culture model system, purified system, and in silico modelling. Upon coexpression of RAP with clusters of the ligand-binding complement repeats (CRs) of the receptors in secreted form in insect cells culture, the isolated proteins had increased yield, enhanced folding, and improved binding properties compared with proteins expressed without RAP, as determined by circular dichroism and surface plasmon resonance. Within LRP1 CR-clusters II and IV, we identified multiple sites comprised of adjacent CR doublets, which provide alternative bivalent binding combinations with specific pairs of lysines on RAP. Mutational analysis of these lysines within each of isolated RAP D1/D2 and D3 domains having high affinity to LRP1 and of conserved tryptophans on selected CR-doublets of LRP1, as well as in silico docking of a model LRP1 CR-triplet with RAP, indicated a universal role for these residues in interaction of RAP and LRP1. Consequently, we propose a new model of RAP interaction with LDLR family receptors based on switching of the bivalent contacts between molecules over time in a dynamic mode.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2016

Experimental Evaluation of the Scale Model Method to Simulate Lunar Vehicle Dynamics

As compared to driving on Earth, the presence of lower gravity and uneven terrain on planetary bodies makes high speed driving difficult. In order to maintain ground contact and control vehicles need to be designed with special attention to dynamic response. The challenge of maintaining control on the Moon was evident during high speed operations of the Lunar Roving Vehicle (LRV) on Apollo 16, as at one point all four tires were off the ground; this event has been referred to as the Lunar Grand Prix. Ultimately, computer simulation should be used to examine these phenomena during the vehicle design process; however, experimental techniques are required for the validation and elucidation of key issues. The objectives of this study were to evaluate the methodology for developing a scale model of a lunar vehicle using similitude relationships and to test how vehicle configuration, six or eight wheel pods, and local tire compliance, soft or stiff, affect the vehicles dynamic performance. A wheel pod consists of a drive and steering transmission and wheel. The Lunar Electric Rover (LER), a human driven vehicle with a pressurized cabin, was selected as an example for which a scale model was built. The scaled vehicle was driven over an obstacle and the dynamic response was observed and then scaled to represent the full-size vehicle in lunar gravity. Loss of ground contact, in terms of vehicle travel distance with tires off the ground, was examined. As expected, local tire compliance allowed ground contact to be maintained over a greater distance. However, switching from a six-tire configuration to an eight-tire configuration with reduced suspension stiffness had a negative effect on ground contact. It is hypothesized that this was due to the increased number or frequency of impacts. The development and testing of this scale model provided practical lessons for future low-gravity vehicle development.

Moon↗
DOE OSTI2021

Quasi-Dynamic Electromagnetic Field Safety Analysis and Mitigation for High-Power Dynamic Wireless Charging of Electric Vehicles

Dynamic wireless charging of electric vehicles (EV) is an emerging charging technology to enable non-contact wireless charging while the vehicle is moving. Compared to stationary wireless charging, in-motion wireless charging involves dynamic processes in which an EV is passing over the charging pads (transmitters). This in motion process makes the dynamic electromagnetic (EM) environment more complicated, and EM safety needs to be ensured under all circumstances. This is due to the fact that the entire vehicle body may be exposed to magnetic fields while the vehicle moves over the energized transmitter. This paper investigates several typical charging scenarios when EVs approach, pass over, and move away from the charging pads. Quasi-dynamic models, which are preliminarily verified by coils’ inductance measurements, are developed to analyze the dynamic process. Based on the quasi-dynamic analysis, shielding solutions are also studied to ensure EM safety for the dynamic wireless charging processes.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Self‐Lubricating Tribo‐Catalytic Activity of 2D High Entropy Alloy Nanoflakes

High Entropy Alloys (HEAs) have garnered attention due to their remarkable tribological attributes. Predominantly, failure mechanisms in HEAs emanate from stress‐induced dislocations, culminating in crack propagation and film delamination. In this study, we report on the synthesis of 2D HEA of (MoWNbTaV) 0.2 S 2 which facilitates shear‐induced energy dissipation at sliding interfaces. The ball‐on‐disk tribological investigations demonstrate unprecedentedly low average coefficients of friction (0.076) and wear rates (10 −9 mm 3 (N∙m) −1 ) under high contact pressures (0.936 GPa) within ambient conditions. Employing multi‐scale characterizations alongside molecular dynamic simulations, we elucidate that the presence of the HEA triggers tribocatalytic activity under high contact pressures emerging as a pivotal factor in extending lubricant lifespan during tribological tests. The resilient lubriciousness coupled with the facile spray coating methodology of (MoWNbTaV) 0.2 S 2 in ambient environments paves the way for the development of a new class of solid lubricants based on 2D HEA.

2D solid lubricant↗
NASA NTRS2018

Preliminary Jitter Stability Results for the Large UV/Optical/Infrared (LUVOIR) Surveyor Concept Using a Non-Contact Vibration Isolation and Precision Pointing System

The need for high payload dynamic stability and ultra-stable mechanical systems is an overarching technology need for large space telescopes such as the Large Ultraviolet / Optical / Infrared (LUVOIR) Surveyor concept. The LUVOIR concept includes a 15-meter-diameter segmented-aperture telescope with a suite of serviceable instruments operating over a range of wavelengths between 100nm to 2.5 um. Wavefront error (WFE) stability of less than 10 picometers RMS of uncorrected system WFE per wavefront control step represents a drastic performance improvement over current space-based telescopes being fielded. Through the utilization of an isolation architecture that involves no mechanical contact between the telescope and the host spacecraft structure, a system design is realized that maximizes the telescope dynamic stability performance without driving stringent technology requirements on spacecraft structure, sensors or actuators. Through analysis of the LUVOIR finite element model and linear optical model, the wavefront error and Line-Of-Sight (LOS) jitter performance is discussed in this paper when using the Vibration Isolation and Precision Pointing System (VIPPS) being developed cooperatively with Lockheed Martin in addition to a multi-loop control architecture. The multi-loop control architecture consists of the spacecraft Attitude Control System (ACS), VIPPS, and a Fast Steering Mirror on the instrument. While the baseline attitude control device for LUVOIR is a set of Control Moment Gyroscopes (CMGs), Reaction Wheel Assembly (RWA) disturbance contribution to wavefront error stability and LOS stability are presented to give preliminary results in this paper. CMG disturbance will be explored in further work to be completed.

Sacks, Lia W.↗
DOE OSTI2020

Negatively Charged Lipids Exhibit Negligible Effects on the Water Repellency of Montmorillonite Films

Amphiphilic molecules can alter the wettability of soil minerals. To determine how the headgroup chemistry of amphiphiles determines these effects, we investigate a system of the clay montmorillonite with long-chain phospholipids. We use phosphatidylglycerol (PG) phospholipids to contrast with our previous work using phosphatidylethanolamine lipids (PE). Zwitterionic PE lipids can sorb to the negatively-charged montmorillonite surface, whereas negatively-charged PG lipids cannot. Employing a suite of techniques from molecular dynamics, atomic force microscopy, fluorescence microscopy, and contact angle measurements, we define sample characteristics from molecular scale structure to the macroscopic wettability. We find that PG lipids do not significantly alter montmorillonite wetting characteristics, such as the contact angle, flow viscosity, and the characteristic timescale for droplet imbibition. In comparing PE and PG lipid/clay films, we find that, among the phospholipids compared, they must have three characteristics in order to change clay/lipid film wettability: they must bind to the mineral surface, be solid at room temperature, and have a relatively continuous distribution throughout the film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Subcycle contact-free nanoscopy of ultrafast interlayer transport in atomically thin heterostructures

Tunnelling is one of the most fundamental manifestations of quantum mechanics. The recent advent of lightwave-driven scanning tunnelling microscopy has revolutionized ultrafast nanoscience by directly resolving electron tunnelling in electrically conducting samples on the relevant ultrashort length- and timescales. In this work, we introduce a complementary approach based on terahertz near-field microscopy to perform ultrafast nano-videography of tunnelling processes even in insulators. The central idea is to probe the evolution of the local polarizability of electron–hole pairs with evanescent terahertz fields, which we detect with subcycle temporal resolution. In a proof of concept, we resolve femtosecond interlayer transport in van der Waals heterobilayers and reveal pronounced variations of the local formation and annihilation of interlayer excitons on deeply subwavelength, nanometre scales. Such contact-free nanoscopy of tunnelling-induced dynamics should be universally applicable to conducting and non-conducting samples and reveal how ultrafast transport processes shape functionalities in a wide range of condensed matter systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1980

Research in nonlinear structural and solid mechanics

Nonlinear analysis of building structures and numerical solution of nonlinear algebraic equations and Newton's method are discussed. Other topics include: nonlinear interaction problems; solution procedures for nonlinear problems; crash dynamics and advanced nonlinear applications; material characterization, contact problems, and inelastic response; and formulation aspects and special software for nonlinear analysis.

Mccomb, H. G., Jr.↗