Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering - Mechanical and civil engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A review of NASA's propulsion programs for aviation

A review of five NASA engine-oriented propulsion programs of major importance to civil aviation are presented and discussed. Included are programs directed at exploring propulsion system concepts for (1) energy conservation subsonic aircraft (improved current turbofans, advanced turbofans, and advanced turboprops); (2) supersonic cruise aircraft (variable cycle engines); (3) general aviation aircraft (improved reciprocating engines and small gas turbines); (4) powered lift aircraft (advanced turbofans); and (5) advanced rotorcraft.

Stewart, W. L.↗
NASA NTRS1998

Transport Between the Tropical and Midlatitude Lower Stratosphere: Implications for Ozone Response to High Speed Civil Transport Emissions

Several recent studies have quantified the air exchange rate between the tropics and midlatitudes in the lower stratosphere using airborne and satellite measurements of chemical species. It is found that the midlatitude air is mixed into the tropical lower stratosphere with a replacement timescale of 13.5 months (with 20% uncertainty) for the region from the tropopause to 21 km and at least 18 months for the region of 20-28 km. These estimates are used to adjust the horizontal eddy diffusion coefficients, K(sub yy), in a two-dimensional chemistry transport model. The value of K(sub yy) previously used to simulate the subtropical barrier, 0.03 x 10(exp 6)sq m/s, generates an exchange time of about 4 years, and the model without subtropical barrier (K(sub yy) = 0.3 x 10(exp 6)sq m/s) has an exchange time of 5 months. Adjusting the K(sub yy) to 0.13 x 10(exp 6) sq m/s from the tropopause to 21 km and 0.07 x 10(exp 6)sq m/s above 21 km produces the exchange timescales which match the estimates deduced from the measurements. The subtropical barrier prevents the engine emissions of the high-speed civil transport (HSCT) aircraft from being transported into the tropics and subsequently lifted into the upper atmosphere or mixed into the southern hemisphere. The model results show that the calculated ozone response to HSCT aircraft emissions using the K(sub yy), adjusted to observed mixing rates is substantially smaller than that simulated without the subtropical barrier.

Shia, R.-L.↗
NASA NTRS1998

Transport Between the Tropical and Midlatitude Lower Statosphere: Implications for Ozone Response to High-Speed Civil Transport Emissions

Several recent studies have quantified the air exchange rate between the tropics and midlatitudes in the lower stratosphere using airborne and satellite measurements of chemical species. It is found that the midlatitude air is mixed into the tropical lower stratosphere with a replacement timescale of 13.5 months (with 20% uncertainty) for the region from the tropopause to 21 km and at least 18 months for the region of 20-28 km. These estimates are used to adjust the horizontal eddy diffusion coefficients, K(sub yy), in a two-dimensional chemistry transport model. The value of K(sub yy) previously used to simulate the subtropical barrier, 0.03 x 10(exp 6) sq m/s, generates an exchange time of about 4 years, and the model without subtropical barrier (K(sub yy) = 0.3 x 10(exp 6) sq m/s) has an exchange time of 5 months. Adjusting the K(sub yy) to 0.13 x 10(exp 6) sq m/s from the tropopause to 21 km and 0.07 x 10(exp 6) sq m/s above 21 km produces the exchange timescales which match the estimates deduced from the measurements. The subtropical barrier prevents the engine emissions of the high-speed civil transport (HSCT) aircraft from being transported into the tropics and subsequently lifted into the upper atmosphere or mixed into the southern hemisphere. The model results show that the calculated ozone response to HSCT aircraft emissions using the K(sob yy) adjusted to observed mixing rates is substantially smaller than that simulated without the subtropical barrier.

Shia, R.-L.↗
NASA NTRS1990

Composites boost 21st-century aircraft engines

Research and development in light-weight, high-temperature composite materials for ultrahigh-bypass engines to be used in high-speed civil transport/rotocraft is presented. It is noted that the expected benefits to be attained by this R&D include weight reduction, lowered fuel consumption, and lower direct operating costs. A major effort underway in this area is the Advanced High Temperature Engine Materials Technology Program (HITEMP) of NASA, which focuses on providing revolutionary high-temperature composite materials: to 425 C (800 F) for polymer-matrix composites (PMCs), to 1250 C (2280 F) for metal-matrix/intermetallic-matrix composites (MMCs/IMCs), and to as high as 1650 C (3000 F) for ceramic-matrix composites (CMCs). Analytical modeling is being used to investigate the structural behavior of these advanced materials in six distinct areas: micromechanics, deformation and damage, fatigue, fracture, trade-off studies, and load definition. It is concluded that the development of advanced materials such as high-temperature composites is highly dependent on the availability of high-temperature fibers. The wide range of fiber characteristics needed will require the development of more than one fiber. In general, a candidate fiber should have low density, high strength, high stiffness, a CTE matching the matrix, chemical compatibility with the matrix, environmental stability and appropriate fiber diameter.

Stephens, Joseph R.↗
NASA NTRS2003

Ultra-Efficient Engine Technology Project Continued to Contribute to Breakthrough Technologies

The International Civil Aviation Organization (ICAO), the U.S. Environmental Protection Agency (EPA), local environmental groups, and the public have become increasingly concerned over damage to local air quality from aircraft emissions and the impact of producing greenhouse gases. The NASA Glenn Research Center has been working to develop revolutionary technologies to minimize environmentally harmful engine emissions, such as nitrogen oxides, carbon dioxide, aerosols, and particulates. The two objectives of UEET are (1) to develop technologies to reduce nitrogen oxide (NOx) emissions by 70 percent below 1996 ICAO regulations and (2) to decrease carbon dioxide emissions (CO2) by dramatically increasing performance and efficiency. High temperature engine materials, ultra-low-NOx combustor designs, efficient, highly loaded turbomachinery, and propulsion-airframe integration analysis are technologies being developed at Glenn to meet these goals. Technology developed in the previous Advanced Subsonic Technology Program is being put into commercial production for large and regional aircraft to reduce NOx emissions 50 percent below 1996 ICAO regulations for landing and takeoff cycles. UEET will take the technology to the next quantum leap-reducing emissions to 70 percent below the ICAO regulations level. In addition, NASA-developed research will significantly reduce carbon monoxide, unburned hydrocarbons, and corresponding cruise NOx levels for the next generation of aircraft engines. Glenn's UEET research will be useful across the whole range of flight: subsonic, supersonic, and hypersonic. It will improve the subsonic transportation that the public depends on, contribute to supersonic commercial aircraft, improve military aircraft, and contribute to the design of a future hypersonic vehicle. These technologies are contributing to a better quality of life on Earth.

Shaw, Robert J.↗
NASA NTRS1991

National Launch System Space Transportation Main Engine

The present liquid-oxygen/liquid-hydrogen engine is described as meeting the specific requirements of the National Launch System (NLS) Program including cost-effectiveness and robustness. An overview of the NLS and its objectives is given which indicates that the program aims to develop a flexible launch system to meet security, civil, and commercial needs. The Space Transportation Main Engine (STME) provides core and boost propulsion for the 1.5-stage vehicle and core propulsion for the solid booster vehicle. The design incorporates step-throttling, order-of-magnitude reductions in welds, and configuration targets designed to optimize robustness. The STME is designed to provide adaptable and dependable propulsion while minimizing recurring costs and is designed to meet the needs of NLS and other typical space-transportation programs currently being planned.

Hoodless, Ralph M., Jr.↗
NASA NTRS1989

Technology and the civil future in space; Proceedings of the Twenty-sixth Goddard Memorial Symposium, Greenbelt, MD, Mar. 16-18, 1988

Reviews, reports, lectures, and panel discussions on technological aspects of current and planned NASA space missions are presented. Included are the viewpoints of NASA, the U.S. aerospace industry, potential commercial users of the civil space infrastructure, and university scientists and engineers. Sections are devoted to technology policy and plans, technology needs, technology directions, and the Astronautical Society student program.

Harris, Leonard A.↗
NASA NTRS2000

Multidisciplinary High-Fidelity Analysis and Optimization of Aerospace Vehicles: Formulation - Part 1

An objective of the High Performance Computing and Communication Program at the NASA Langley Research Center is to demonstrate multidisciplinary shape and sizing optimization of a complete aerospace vehicle configuration by using high-fidelity, finite element structural analysis and computational fluid dynamics aerodynamic analysis in a distributed, heterogeneous computing environment that includes high performance parallel computing. A software system has been designed and implemented to integrate a set of existing discipline analysis codes, some of them computationally intensive, into a distributed computational environment for the design of a highspeed civil transport configuration. The paper describes the engineering aspects of formulating the optimization by integrating these analysis codes and associated interface codes into the system. The discipline codes are integrated by using the Java programming language and a Common Object Request Broker Architecture (CORBA) compliant software product. A companion paper presents currently available results.

Walsh, J. L.↗
NASA NTRS2004

Analysis of Fuel Vaporization, Fuel-Air Mixing, and Combustion in Integrated Mixer-Flame Holders

Requirements to limit pollutant emissions from the gas turbine engines for the future High-Speed Civil Transport (HSCT) have led to consideration of various low-emission combustor concepts. One such concept is the Integrated Mixer-Flame Holder (IMFH). This report describes a series of IMFH analyses performed with KIVA-II, a multi-dimensional CFD code for problems involving sprays, turbulence, and combustion. To meet the needs of this study, KIVA-II's boundary condition and chemistry treatments are modified. The study itself examines the relationships between fuel vaporization, fuel-air mixing, and combustion. Parameters being considered include: mixer tube diameter, mixer tube length, mixer tube geometry (converging-diverging versus straight walls), air inlet velocity, air inlet swirl angle, secondary air injection (dilution holes), fuel injection velocity, fuel injection angle, number of fuel injection ports, fuel spray cone angle, and fuel droplet size. Cases are run with and without combustion to examine the variations in fuel-air mixing and potential for flashback due to the above parameters. The degree of fuel-air mixing is judged by comparing average, minimum, and maximum fuel/air ratios at the exit of the mixer tube, while flame stability is monitored by following the location of the flame front as the solution progresses from ignition to steady state. Results indicate that fuel-air mixing can be enhanced by a variety of means, the best being a combination of air inlet swirl and a converging-diverging mixer tube geometry. With the IMFH configuration utilized in the present study, flashback becomes more common as the mixer tube diameter is increased and is instigated by disturbances associated with the dilution hole flow.

Deur, J. M.↗
NASA NTRS2005

A Comparative Propulsion System Analysis for the High-Speed Civil Transport

Six of the candidate propulsion systems for the High-Speed Civil Transport are the turbojet, turbine bypass engine, mixed flow turbofan, variable cycle engine, Flade engine, and the inverting flow valve engine. A comparison of these propulsion systems by NASA's Glenn Research Center, paralleling studies within the aircraft industry, is presented. This report describes the Glenn Aeropropulsion Analysis Office's contribution to the High-Speed Research Program's 1993 and 1994 propulsion system selections. A parametric investigation of each propulsion cycle's primary design variables is analytically performed. Performance, weight, and geometric data are calculated for each engine. The resulting engines are then evaluated on two airframer-derived supersonic commercial aircraft for a 5000 nautical mile, Mach 2.4 cruise design mission. The effects of takeoff noise, cruise emissions, and cycle design rules are examined.

Berton, Jeffrey J.↗
NASA NTRS1976

Research requirements for emergency power to permit hover-one-engine-inoperative helicopter operation

The research and technology demonstration requirements to achieve emergency-power capability for a civil helicopter are documented. The goal for emergency power is the ability to hover with one engine inoperative, transition to minimum-power forward flight, and continue to a safe landing where emergency power may or may not be required. The best method to obtain emergency power is to augment the basic engine power by increasing the engine's speed and turbine-inlet temperature, combined with water-alcohol injection at the engine inlet. Other methods, including turbine boost power and flywheel energy, offer potential for obtaining emergency power for minimum time durations. Costs and schedules are estimated for a research and development program to bring emergency power through a hardware-demonstration test. Interaction of engine emergency-power capability with other helicopter systems is examined.

Yost, J. H.↗
NASA NTRS2010

Effects of Gas Turbine Component Performance on Engine and Rotary Wing Vehicle Size and Performance

In support of the Fundamental Aeronautics Program, Subsonic Rotary Wing Project, further gas turbine engine studies have been performed to quantify the effects of advanced gas turbine technologies on engine weight and fuel efficiency and the subsequent effects on a civilian rotary wing vehicle size and mission fuel. The Large Civil Tiltrotor (LCTR) vehicle and mission and a previous gas turbine engine study will be discussed as a starting point for this effort. Methodology used to assess effects of different compressor and turbine component performance on engine size, weight and fuel efficiency will be presented. A process to relate engine performance to overall LCTR vehicle size and fuel use will also be given. Technology assumptions and levels of performance used in this analysis for the compressor and turbine components performances will be discussed. Optimum cycles (in terms of power specific fuel consumption) will be determined with subsequent engine weight analysis. The combination of engine weight and specific fuel consumption will be used to estimate their effect on the overall LCTR vehicle size and mission fuel usage. All results will be summarized to help suggest which component performance areas have the most effect on the overall mission.

Snyder, Christopher A.↗
NASA NTRS2000

Inlet Unstart Propulsion Integration Wind Tunnel Test Program Completed for High-Speed Civil Transport

One of the propulsion system concepts to be considered for the High-Speed Civil Transport (HSCT) is an underwing, dual-propulsion, pod-per-wing installation. Adverse transient phenomena such as engine compressor stall and inlet unstart could severely degrade the performance of one of these propulsion pods. The subsequent loss of thrust and increased drag could cause aircraft stability and control problems that could lead to a catastrophic accident if countermeasures are not in place to anticipate and control these detrimental transient events. Aircraft system engineers must understand what happens during an engine compressor stall and inlet unstart so that they can design effective control systems to avoid and/or alleviate the effects of a propulsion pod engine compressor stall and inlet unstart. The objective of the Inlet Unstart Propulsion Airframe Integration test program was to assess the underwing flow field of a High-Speed Civil Transport propulsion system during an engine compressor stall and subsequent inlet unstart. Experimental research testing was conducted in the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center at Lewis Field. The representative propulsion pod consisted of a two-dimensional, bifurcated inlet mated to a live turbojet engine. The propulsion pod was mounted below a large flat plate that acted as a wing simulator. Because of the plate s long length (nominally 10-ft wide by 18-ft long), realistic boundary layers could form at the inlet cowl plane. Transient instrumentation was used to document the aerodynamic flow-field conditions during an unstart sequence. Acquiring these data was a significant technical challenge because a typical unstart sequence disrupts the local flow field for about only 50 msec. Flow surface information was acquired via static pressure taps installed in the wing simulator, and intrusive pressure probes were used to acquire flow-field information. These data were extensively analyzed to determine the impact of the unstart transient on the surrounding flow field. This wind tunnel test program was a success, and for the first time, researchers acquired flow-field aerodynamic data during a supersonic propulsion system engine compressor stall and inlet unstart sequence. In addition to obtaining flow-field pressure data, Glenn researchers determined other properties such as the transient flow angle and Mach number. Data are still being reduced, and a comprehensive final report will be released during calendar year 2000.

Porro, A. Robert↗
DOE OSTI2025

Data Repository for Multi-Objective Urban Observational Strategies: A risk-based framework for expanding flood sensor networks.

These data support the manuscript "Multi-Objective Urban Observational Strategies: A risk-based framework for expanding flood sensor networks." These data are generated to allow water managers to reason about optimal locations to expand a flood observation system from multiple perspectives, specifically focusing on flood hazards, and population exposure to flooding. The data included are a) a shapefile of individual sensor locations b) a shapefile of river reach catchments, c) raster of FEMA flood likelihood layers d) shapefile of population locations and population socioeconomic characteristics. The code is written in R and includes all files necessary to generate the figures for the associated manuscript. Interactive maps of the final calculated maps of hazard, vulnerability, exposure, and risk are also included as html files.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1976

Research requirements for development of improved helicopter rotor efficiency

The research requirements for developing an improved-efficiency rotor for a civil helicopter are documented. The various design parameters affecting the hover and cruise efficiency of a rotor are surveyed, and the parameters capable of producing the greatest potential improvement are identified. Research and development programs to achieve these improvements are defined, and estimated costs and schedules are presented. Interaction of the improved efficiency rotor with other technological goals for an advanced civil helicopter is noted, including its impact on engine noise, hover and cruise performance, one-engine-inoperative hover capability, and maintenance and reliability.

Davis, S. J.↗
NASA NTRS1992

Advanced takeoff procedures for high-speed civil transport community noise reduction

Advanced takeoff procedures were developed for a Mach 2.62 high-speed civil transport configuration (HSCT) equipped with turbine bypass engines, with the goal of reducing the takeoff noise levels for certification to FAR 36, Stage 3 noise levels. The detailed takeoff and landing module for the Flight Optimizations System (FLOPS) computer program was used to generate takeoff profiles. All takeoff procedures were constrained to meet a FAR takeoff field length of 11,000 feet, as well as the minimum required engine-out climb gradients for each airbome segment. Aircraft noise levels at the FAR 36 certification points were calculated using the Aircraft Noise Prediction Program (ANOPP). The study showed that using advanced takeoff procedures in noise certification could result in a 2.25 dB reduction in the amount of noise suppression required to certify this configuration for Stage 3 noise limits. Advanced procedures also resulted in an 8 percent reduction in the 100 EPNdB noise footprint area compared to basic FAR 36 takeoff procedures. In addition, improvements in the lift-to-drag ratio using high-lift devices were shown to produce 1.81 dB more noise reduction when used in combination with advanced takeoff procedures.

Olson, E. D.↗
NASA NTRS1999

Design Tool Developed for Probabilistic Modeling of Ceramic Matrix Composite Strength

Ceramic matrix composites are being evaluated as candidate materials for many high temperature applications such as engine combustor liners for the High-Speed Civil Transport (HSCT). They are required to have an assured life of several thousand hours. Estimating the reliability of these components is quite a complex process and requires knowledge of the uncertainties that occur at various scales. The properties of ceramic matrix composites (CMC) are known to display a considerable amount of scatter due to variations in fiber/matrix properties, interphase/coating properties, bonding, amount of matrix voids, and many geometry- and fabrication-related parameters such as ply thickness and ply orientations. The objective of this research effort is to account for these uncertainties in a formal way by probabilistically analyzing both the stiffness- and strength related properties of CMC's. In current deterministic approaches, uncertainties are usually accounted for by safety factors. This approach often yields overly conservative designs, thereby reducing the potential of many advanced composite materials.

Murthy, Pappu L. N.↗