Search NASA⌕ Search

SEARCH · Search NASA

Results for “Epoxy Resins”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

V-378A: A modified bismaleimide for advanced composites

Addition polyimides cure with no evolution of gaseous by-products at relatively low temperatures and may be cured at low pressures to yield composites with excellent hot-wet strength retention. These properaties have made them excellent candidates as matrix resins for advanced composites. However, commercially available bismaleimides are solids and difficult to handle in preimpregnated form. V-378A is an addition polyimide composed of a mixture of bismaleimides and other reactive ingredients formulated to provide good prepreg properties and handling, facile cure and excellent composite mechanical properties. Several curing mechanisms are utilized to provide the characteristics exhibited by V-378A. Part of the mechanism is free radial and takes place at ambient temperature and above. Other mechanisms are principally Diels-Alder in nature. V-378A prepregs are tacky at ambient temperature, but do not have long tacky outlife similar to some epoxies. V-378A yields composites which exhibit hot-wet strength retention which is superior to that provided by epoxy resin systems.

Street, S. W.↗
NASA NTRS1993

Verification of a two-dimensional infiltration model for the resin transfer molding process

A two-dimensional finite element model for the infiltration of a dry textile preform by an injected resin was verified. The model, which is based on the finite element/control volume technique, determines the total infiltration time and the pressure increase at the mold inlet associated with the RTM process. Important input data for the model are the compaction and permeability behavior of the preform along with the kinetic and rheological behavior of the resin. The compaction behavior for several textile preforms was determined by experimental methods. A power law regression model was used to relate fiber volume fraction to the applied compaction pressure. Results showed a large increase in fiber volume fraction with the initial application of pressure. However, as the maximum fiber volume fraction was approached, the amount of compaction pressure required to decrease the porosity of the preform rapidly increased. Similarly, a power law regression model was used to relate permeability to the fiber volume fraction of the preform. Two methods were used to measure the permeability of the textile preform. The first, known as the steady state method, measures the permeability of a saturated preform under constant flow rate conditions. The second, denoted the advancing front method, determines the permeability of a dry preform to an infiltrating fluid. Water, corn oil, and an epoxy resin, Epon 815, were used to determine the effect of fluid type and viscosity on the steady state permeability behavior of the preform. Permeability values measured with the different fluids showed that fluid viscosity had no influence on the permeability behavior of 162 E-glass and TTI IM7/8HS preforms. Permeabilities measured from steady state and advancing front experiments for the warp direction of 162 E-glass fabric were similar. This behavior was noticed for tests conducted with corn oil and Epon 815. Comparable behavior was observed for the warp direction of the TTI IM7/8HS preform and corn oil. Mold filling and flow visualization experiments were performed to verify the analytical computer model. Frequency dependent electromagnetic sensors were used to monitor the resin flow front as a function of time. For the flow visualization tests, a video camera and high resolution tape recorder were used to record the experimental flow fronts. Comparisons between experimental and model predicted flow fronts agreed well for all tests. For the mold filling tests conducted at constant flow rate injection, the model was able to accurately predict the pressure increase at the mold inlet during the infiltration process. A kinetics model developed to predict the degree of cure as a function of time for the injected resin accurately calculated the increase in the degree of cure during the subsequent cure cycle.

Hammond, Vincent H.↗
NASA NTRS2023

PMT F7 Silver Standard Material Properties Characterization

PMT F7 epoxy resin was characterized to capture the material's thermochemical and thermo-mechanical properties. DSC testing was performed and the data was used to develop a cure kinetics model which predicts the material cure response and specific heat capacity. TMA and DMA testing were performed and the data was used to develop thermo-mechanical models which predict the material CTE, cure shrinkage, and modulus evolution with cure. Convergent Manufacturing Technologies US determined test parameters, analyzed data, and performed model fitting. NASA completed tests and provided data to Convergent Manufacturing Technologies US.

Epoxy↗
DOE OSTI2026

Impact of DMP-30 catalyst concentration on the degradation and kinetics of bisphenol A epoxy thermosets cured with linear amine hardener

Epoxy thermosets are a crucial component in carbon-fiber composites, serving as the organic binding matrix. Catalysts are commonly used in prepolymer formulations to accelerate curing of the thermosets. However, the impact of catalysts on the thermal stability, degradation pathways, and kinetics of the final thermoset is poorly understood. Here, in this work, Product-Specific Kinetics (PSK) analysis was utilized with isoconversional kinetics to provide a first look into the degradation kinetics of major pyrolysis pathways in bisphenol A (BPA) epoxy resins and determine the impact of altering catalysis concentrations on these kinetic pathways. Results revealed new insights into previously identified degradation pathways, provided evidence of multiple degradation pathways for some products, and showed that use of excess catalyst results in polymer network alterations and reduced thermal stability of the thermosets.

Bisphenol A↗
NASA NTRS2006

Clay Nanocomposite/Aerogel Sandwich Structures for Cryotanks

GRC research has led to the development of epoxy-clay nanocomposites with 60-70% lower gas permeability than the base epoxy resin. Filament wound carbon fiber reinforced tanks made with this nanocomposite had a five-fold lower helium leak rate than the corresponding tanks made without clay. More recent work has produced new composites with more than a 100-fold reduction in helium permeability. Use of these advanced, high barrier composites would eliminate the need for a liner in composite cryotanks, thereby simplifying construction and reducing propellant leakage. Aerogels are attractive materials for use as cryotank insulation because of their low density and low thermal conductivity. However, aerogels are fragile and have poor environmental stability, which have limited their use to certain applications in specialized environments (e.g., in certain types of nuclear reactors as Cerenkov radiation detectors, and as thermal insulators aboard space rovers on Mars). New GRC developed polymer crosslinked aerogels (X-Aerogels) retain the low density of conventional aerogels, but they demonstrate a 300-fold increase in their mechanical strength. Currently, our strongest materials combine a density of approx. 0.45 g/cc, a thermal conductivity of approx. 0.04 W/mK and a compressive strength of ~185 MPa. Use of these novel aerogels as insulation materials/structural components in combination with the low permeability of epoxy-clay nanocomposites could significantly reduce cryotank weight and improve durability.

Miller, Sandi↗
DOE OSTI2021

The interpenetration polymer network in a cement paste–waterborne epoxy system

The formation of the interpenetrating polymer network (IPN) structure within the cement-polymer system has been revealed by experiments from 2 dimensional to 3-dimensional scales. However, the microstructure design and performance prediction of IPN as a function of specific C-S-H/polymer components or ingredients' parameters e.g. water to cement ratios (w/c), polymer to cement ratios (p/c), monomer components, degree of polymerization (DP), etc. is by far not available. Here we developed a mesoscale model for IPN visualization based on the Flory-Huggins interaction theory which was applied to cement science for the first time. All the ingredients in the micro-structure were considered as soluble beads with rational sizes based on their properties obtained by molecular dynamic methods. The interaction parameters of each bead were then determined based on their element ratios and chemical backbones. The model was validated with the waterborne epoxy-cement material (WECM) in which a novel waterborne epoxy resin (WEP) was prepared and impregnated. The verification results on the 2D-3D scale show that the developed model predicts the WECM's IPN structures by rule and line concerning DP, w/c, and p/c in the mixture. The C-S-H beads were progressively scaled in size which alters the C-S-H texture to have completely different dissolution characteristics. Beads of diameter ~6 Å are more unstable and soluble which enable them to form a continuous phase in water or a composite structure with WEP. In contrast, beads with diameters larger than 10 Å have different properties with stronger nucleation effects. The results also suggest the impregnation content of WEP in cement-based material should be limited to 10% vol. to prevent the polymer IPN from decomposing into discrete clusters. The application of Flory-Huggins theory in cement-based composites demonstrates great potential in performance prediction and microstructure design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Towards functionalized lignin and its derivatives for high-value material applications

In pursuit of low-carbon development, the production of diverse functional materials from renewable resources, especially lignocellulosic biomass, is of vital importance. Lignin is a major component of lignocellulose, and it is nature's only true high-volume aromatic polymer, which has the advantages of biodegradability, biocompatibility, and low acquisition cost. After modification by a variety of physicochemical strategies, it can be applied as an alternative to basic industrial materials, including polyurethanes, phenolic, and epoxy resins, which stands comparably to conventional synthetic polymers in terms of both performance and reduced cost. To further unlock the potential of lignin, an alluring opportunity is the exploitation of lignin for high-value materials, especially nanomaterials, that find extensive applications in energy and environment areas. This review provides a systematic summary and perspective of research that has been devoted to lignin transformation to high-value materials, ranging from industrially well-established engineering materials to the recently emerged nanomaterials that were used for energy and environment applications. Latest cutting-edge innovations on lignin modification, controlled depolymerization, and assembly during the last five years are summarized. Structure-function relationships of lignin materials in terms of their specific applications are analyzed. Furthermore, challenges and future opportunities for lignin conversion to high-value materials are also provided. We wish this review will stimulate further advances in lignin based high-value materials, and promote “waste” into “wealth”.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic heterogeneity and nanophase separation in rubber-toughened amine-cured highly cross-linked polymer networks

Solid state nuclear magnetic resonance (NMR) spectroscopy and small-to wide-angle X-ray scattering (SWAXS) methods were used to characterize the heterogeneous dynamics and polymer domain structure in rubber modified thermoset materials containing the diglycidyl ether of bisphenol A (DGEBA) epoxy resin and a mixture of Jeffamine reactive rubber and 4,4-diaminodicyclohexylmethane (PACM) amine curing agent. The polymer chain dynamics and morphologies as a function of the PACM/Jeffamine ratio were determined. Using dipolar-filtered NMR experiments, the resulting networks are shown to be composed of mobile and rigid regions that are separated on nanometer length scales, along with a dynamically immobilized interface region. Proton NMR spin diffusion experiments measured the dimensions of the mobile phase to range between 9 and 66 nm and varied with the relative PACM concentration. Solid state 13 C magic angle spinning NMR experiments show that the highly mobile phase is composed entirely of the dynamically flexible polyether chains of the Jeffamine rubber, the immobilized interface region is a mixture of DGEBA, PACM, and the Jeffamine rubber, with the PACM cross-linked to DGEBA predominantly residing in the rigid phase. The SWAXS results showed compositional nanophase separation spanning the 11–77 nm range. These measurements of the nanoscale compositional and dynamic heterogeneity provide molecular level insight into the very broad and controllable glass transition temperature distributions observed for these highly cross-linked polymer networks.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of a versatile electrochemical cell for in situ grazing-incidence X-ray diffraction during non-aqueous electrochemical nitrogen reduction

In situ techniques are essential to understanding the behavior of electrocatalysts under operating conditions. When employed, in situ synchrotron grazing-incidence X-ray diffraction (GI-XRD) can provide time-resolved structural information of materials formed at the electrode surface. In situ cells, however, often require epoxy resins to secure electrodes, do not enable electrolyte flow, or exhibit limited chemical compatibility, hindering the study of non-aqueous electrochemical systems. Here, a versatile electrochemical cell for air-free in situ synchrotron GI-XRD during non-aqueous Li-mediated electrochemical N 2 reduction (Li-N 2 R) has been designed. This cell not only fulfills the stringent material requirements necessary to study this system but is also readily extendable to other electrochemical systems. Under conditions relevant to non-aqueous Li-N 2 R, the formation of Li metal, LiOH and Li 2 O as well as a peak consistent with the α-phase of Li 3 N was observed, thus demonstrating the functionality of this cell toward developing a mechanistic understanding of complicated electrochemical systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Study of the Heater-Coil Electrical Insulation for the HL-LHC Low Beta Quadrupoles

In the framework of the HL-LHC project, the present LHC low-β superconducting quadrupoles will be substituted with higher performance Nb 3 Sn magnets (MQXF) with 11.4 T coil peak field. MQXF coils are impregnated with epoxy resin to reduce risk of stress concentration on the brittle conductor. The magnet quench protection is provided by CLIQ and quench heaters to ensure a redundant system. Quench heaters are impregnated with the coils in order to have suitable thermal contact with them, and to prevent the hot spot temperature from exceeding 350K during normal operation in case of a quench. Quench heaters are insulated from the coil by S-2 Glass and polyimide. Here, the test of the first MQXF prototype (4 m long) MQXFAP1 was stopped by a coil-to-ground short circuit triggered by a heater-to-coil short. This issue triggered a root analysis of the causes of this short. Here we prove that the use of a non-conforming cloth in coil impregnation, further weakened by non-conforming high voltage test, has triggered the shorts. Moreover, we present an analysis of the heater-to-coil insulation strength, showing the role of blistering phenomena and how they are triggered by a combination of magnet powering and heater firing.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Upscaling of asymmetric hollow fiber‐supported thin film membranes for oxygen separation from air: Proof of concept

Abstract Hollow fiber membranes demonstrate various advantages for high performance oxygen separation. However, the small diameters of hollow fibers and the brittleness of ceramics limit their mechanical strength, imposing great difficulties on stack and module development. Gas‐tight sealing is another challenge for upscaling of hollow fiber membrane technology. Low temperature sealant materials of epoxy resin or silicon are typically used for hollow fiber stacks, requiring that the sealing portions be located out of hot zone. Consequently, only partial length of hollow fibers participates in oxygen permeation. In this study, upscaling of our recently developed asymmetric hollow fiber‐supported thin film membranes is conducted, where individual hollow fibers are assembled in parallel to form a stack. A reliable gas‐tight sealing is obtained by combining ceramic paste with conductive adhesive ink cohesively. Comprehensive oxygen permeation test is conducted with the sealing portions being in hot zone and compared with a single hollow fiber membrane. Fundamental mechanism is discussed to understand the performances and their differences. An accelerated long‐term test (∼320 h, 16 thermal cycles) demonstrates excellent stability and robustness of the stack and sealing. The characterization of post‐test samples further confirms excellent stability and robustness of the phases and microstructures of the stack.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Alkylidene functionalization produces highly recyclable and scalable polyhydroxyalkanoates

Recyclable polymers that can be produced at scale and readily tuned within the same polymer framework for specific properties are important to achieving a circular materials economy. To this end, synthetic poly(3-hydroxyalkanoate)s (PHAs) have emerged as high-performance, chemically recyclable variants of biological PHAs, but their difficult monomer syntheses and suboptimal recycling efficiencies pose challenges for large-scale deployment. In this study, we investigated a β-isopropylidene PHA, i-PHA, for which the lactone monomer can be synthesized by existing industrial methods from biomass-derived isobutyric acid. The alkylidene substituent prevents decarboxylative degradation typically observed during PHA depolymerization, enabling near-quantitative chemical recycling to monomer. Controlled hydrogenation of the β-isopropylidene side group produces PHAs with diverse performance metrics that are competitive with a range of commodity polymers, spanning strong fibers to ductile thermoplastics to superglue epoxy resins.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tailored Fiber Placement for Complex Preforms

Tailored Fiber Placement (TFP) offers a novel approach to optimize fiber architecture for the fabrication of complex, structural parts not traditionally suitable for advanced composites. This technology not only offers new routes for weight reduction via metal substitution, it also offers cost reduction through minimization of material scrap and reduced labor. This reduction in component weight leads to increased fuel efficiency, and reduced production energy consumption, thereby, helping to achieve the stated IACMI technical goals. This technology leverages centuries of manufacturing development in support of the textile and embroidery industry. One major drawback to this technology is the lack of commercial or non- proprietary structural performance data and robust analytical tools used to optimize fiber architecture and predict performance. This project was structured to utilize common sub-element features to validate analytical performance tools, generate performance data, and gather cost and performance data on components of interest. This project was designed to give industry sponsors the confidence and ability to take full advantage of TFP to fabricate primary, highly loaded structure and integrate features such as metallic fasteners. The project focused principally on the use of high strength carbon fiber, such as T700, and the use of aerospace epoxy resin matrix to primarily support development of new composite applications in vehicle, aerospace, and industrial markets. This project applied previously developed analytical tools to predict the performance of TFP produced parts. This work focused on developing the pipeline to characterize material in order to accurately predict component performance when modifying the TFP print paths and stitch density. This focused on experimental characterization via standardized ASTM testing, alongside experimental testing of more representative service components by testing curved beam strength, beam shear performance, a large scale TFP lug, and ultimately designing a fully TFP clip bracket that reduced weight and cost compared to a traditional metallic component. The new knowledge gained from this program included: 1) development and demonstration of novel analytical tools applied to analysis of TFP preforms; 2) development and demonstration of a building block approach using coupons and sub-elements to optimize the design of a more complex component; 3) demonstration that optimized fiber orientation using TFP can exceed performance of conventional textile composite materials and can open new applications currently limited to metallic components; 4) Demonstration of performance and cost benefits of the TFP process as compared to metallic and conventional textile composites. Recommendations for follow-on work include development of design allowables to assess the impact of high temperature/moisture exposure or saturation during loading, tracking the impact of stitching needle wear on the performance of parts and ability to stitch thicker preforms, using TFP preforms as local reinforcement at areas of bearing or complex loading, and topology optimization of components by tow steering. The expertise developed during the course of this project can be leveraged to provide commercial engineering design and fabrication services using TFP. UDRI is in the process of formalizing their partnership with Spintech, who will serve as the commercialization partner for this technology and provide molding services and deliver finished components to the end user. UDRI will continue to produce the preforms until the economics allow Spintech to procure its own TFP equipment or lease UDRI equipment, at which point UDRI will step away from manufacture and serve as the engineering and design lead on product development.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multi-Process Tooling

Decisions made early in the automotive design process influence material selection, which in turn dictates process selection and tool design. Because of tool build time and cost of tooling, the original path is not easily altered, even if there is compelling evidence that another material or process would be beneficial. This project focused on tool design that is agile enough to allow its use in multiple processes—injection, injection compression, and extrusion-compression. This tool design allows for the manufacture of components with the most efficient process or materials, without building multiple, single-process tools. The primary purpose of the Multi-Process Tool project was to physically demonstrate that a single, well-designed tool could be used to manufacture parts with a variety of materials that require different processes. A multi-process tool would be beneficial to providing data for any changes to the process since materials and processes can be interchanged without incurring additional tool cost(s). Battery tray parts, (representative of a multi-process tool, were successfully manufactured using various types of materials, such as fiber reinforced (carbon fiber and/or glass fibers, recycled carbon fibers), amorphous (PP, TPU), semi-crystalline (PA6, PA66), and crystalline (thermoset epoxy resin) polymers. Processing of the parts was achieved by injection molding, compression molding, compression overmolding, and injection overmolding. Specimens extracted from various locations on the battery tray parts were evaluated for mechanical properties (flexure and interlaminar shear strength properties). The results show that the tool can be used to produce parts from a wide range of materials and processes with no degradation of the physical or cosmetic properties.

42 ENGINEERING↗
DOE OSTI2023

Corrosion-Resistant Coatings on Spent Nuclear Fuel Canisters to Mitigate and Repair Potential Stress Corrosion Cracking (FY23 Status)

This report summarizes the activities performed by Sandia National Laboratories in FY23 to identify and test coating materials for the prevention, mitigation, and/or repair of potential chloride-induced stress corrosion cracking in spent nuclear fuel dry storage canisters. This work continues efforts by Sandia National Laboratories that are summarized in previous reports from FY20 through FY22 on the same topic. In FY23, Sandia National Laboratories, in collaboration with five industry partners through a memorandum of understanding, evaluated the physical, mechanical, and corrosion-resistance properties of eight different coating systems. The evaluation included thermal and radiation environments relevant to various time periods of storage for spent nuclear fuel canisters. The coating systems include polymeric (polyetherketoneketone, modified polyimide/polyurea, modified phenolic resin, epoxy), organic/inorganic ceramic hybrids (silane-based polyurethane hybrid and a quasi-ceramic sol-gel polyurethane hybrid), and coatings utilizing a Zn-rich primer applied to stainless steel coupons. The results and implications of these tests are summarized in this report. These analyses will be used to identify the most effective coatings for potential use on spent nuclear fuel dry storage canisters and to identify specific needs for further optimization of coating technologies for application on spent nuclear fuel canisters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Modification of Fractured Rock Permeability Field Using Polymer Foam to Improve Geothermal System Efficiency

The project aims at developing novel methods for blocking high-permeability pathways in geothermal reservoirs to improve heat exchange efficiency. While the project was at DRI, and now when it has been transferred to UNR, the goal of blocking high-permeability pathways is achieved through targeted injection of heat-sensitive polymer foams, particularly foamed epoxy resins, whose activation and curing are triggered by the ambient thermal field.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Experimental Study of Underground Heat Storage via Hydraulic Fractures

In this study, we present a laboratory setup to test the energy flow in the form of underground heat storage using hydraulic fractures, a so-called Fracture Thermal Energy Storage (FTES) system. In the experiment, de-ionized water is circulated under high pressure through steel tubing automatically heated to a target temperature. The fluid adjusts to the tubing temperature during its flow before entering a production well drilled into a 250 mm edge length block of Zimbabwe Gabbro. The warm fluid then circulates through a previously created hydraulic fracture at mid-height of the block to a production well drilled at the block periphery. External fracture appearances are sealed using an epoxy resin and the production well by a cork of polydimethylsiloxane. In this cork, tubing to an open outlet is glued. We demonstrated through the results of a preliminary heating experiment that we can transfer nearly all of the heat from the circulating fluid to the block. An efficient charging of the thermal battery is achieved. This first-order demonstration is currently under further improvement and serves as a knowledge basis for the upscaling of mid- to large-scale field implementation of FTES systems.

Möri, Andreas↗