Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Influence of gradation on shear behavior and pore water response of sand

Here, this paper examines the influence of particle size distribution (PSD) on the shearing behavior of sand using axisymmetric triaxial compression (ATC) testing in conjunction with 3D imaging using synchrotron micro-computed tomography (SMT). Angular sand was sieved to obtain a narrow gradation (uniform) and a wide gradation (non-uniform) with uniformity coefficients (C u ) of 1.2 and 3.0, respectively. Experiments were conducted under drained conditions and a constant effective cell pressure (σ$^{'}_3$) of 50 kPa at low and high back pressures (BP). Results of paired ATC-SMT were analyzed in terms of global constitutive behavior, strain localization, and localized flow characteristics. A new particle tracking algorithm is developed to expose strain localization. Relative particle translation gradient (RPTG) results revealed that gradation affects how early the shear band develops and a tendency for narrow gradation to exhibit varying degrees of diffused shear band at high axial strain (ε 1 ) even though a clear single shear band was observed at the peak strength. Geometric tortuosity (τ) is used as a quantitative parameter to assess flow changes and the efficiency of the flow path. Representative elementary volumes (REVs) inside and outside the shear band were analyzed and the results showed a variation in flow path characteristics where wide gradation specimens had preferential flow paths.

Computed tomography↗
NASA NTRS2003

Mixing and NO(x) Emission Calculations of Confined Reacting Jet Flows in a Cylindrical Duct

Rapid mixing of cold lateral jets with hot cross-stream flows in confined configurations is of practical interest in gas turbine combustors as it strongly affects combustor exit temperature quality, and gaseous emissions in for example rich-lean combustion. It is therefore important to further improve our fundamental understanding of the important processes of dilution jet mixing especially when the injected jet mass flow rate exceeds that of the cross-stream. The results reported in this report describe some of the main flow characteristics which develop in the mixing process in a cylindrical duct. A 3-dimensional tool has been used to predict the mixing flow field characteristics and NOx emission in a quench section of an RQL combustor, Eighteen configurations have been analyzed in a circular geometry in a fully reacting environment simulating the operating condition of an actual RQL gas turbine combustion liner. The evaluation matrix was constructed by varying three parameters: 1) jet-to-mainstream momentum-flux ratio (J), 2) orifice shape or orifice aspect ratio, and 3) slot slant angle. The results indicate that the mixing flow field significantly varies with the value of the jet penetration and subsequently, slanting elongated slots generally improve the mixing uniformity at high J conditions. Round orifices produce more uniform mixing and low NO(x) emissions at low J due to the strong and adequate jet penetration. No significant correlation was found between the NO(x) production rates and the mixing deviation parameters, however, strong correlation was found between NO(x) formation and jet penetration. In the computational results, most of the NO(x) formation occurred behind the orifice starting at the orifice wake region. Additional NO(x) is formed upstream of the orifice in certain configurations with high J conditions due to the upstream recirculation.

Holdeman, James D.↗
NASA NTRS1972

Aeroacoustic characteristics of jet flap type exhausts.

This work which is intended to shed more light on the acoustic and fluid dynamic characteristics of jet flap type exhaust flows, reports and discusses some typical experimental results obtained with cold model air jets in a reverberation chamber. Acoustic data on the total sound power output and the overall noise spectrum of various jet flap configurations are given and compared with data from conventional circular jets. In addition various flow data for the same jets resulting from hot wire measurements are reported and general conclusions are obtained regarding the expected noise source distribution. The results indicate the dependence of the acoustic and flow characteristics on the major nozzle parameters. For the jet flaps the total radiated sound power is found to follow a 3 to 6 power of the exhaust velocity while for the circular jets the 8 power law is confirmed. The noise produced in the secondary mixing region downstream of the flap trailing edge tends to exceed the noise issuing from the primary mixing region.

Gruschka, H. D.↗
NASA NTRS1975

Drainage basin characteristics from ERTS data

The author has identified the following significant results. ERTS-derived measurements of forests, riparian vegetation, open water, and combined agricultural and urban land use were added to an available matrix of map-derived basin characteristics. The matrix of basin characteristics was correlated with 40 stream flow characteristics by multiple regression techniques. Fifteen out of the 40 equations were improved. If the technique can be transferred to other physiographic regions in the nation, the opportunity exists for a potential annual savings in operations of about $250,000.

Hollyday, E. F.↗
NASA NTRS1976

Evaluation of scramjet combustor performance using cold nonreactive mixing tests

Results of cold supersonic ducted mixing tests are presented and compared with results of hot mixing and combustion tests obtained using the same apparatus. Two strut injectors are evaluated, one with injectors parallel to the free-stream direction and one with perpendicular injectors. Detailed flow surveys are used to determine the degree of mixing accomplished in the cold flow tests. In the hot flow tests, the amount of mixing and reaction is inferred from survey data and comparison of wall static pressures with one-dimensional flow calculations. These comparisons show that cold mixing results can be used to predict combustion results. In some cases, such as the normal injection strut tested, cold mixing efficiency and combustion efficiency are identical. In other cases, transport models developed from cold flow results can be applied to predict the effects of higher temperature mixing and reaction. Cold flow surveys are also used to determine detailed flow characteristics not readily measured in hot flows.

Mcclinton, C. R.↗
NASA NTRS1987

Structural and preliminary thermal performance testing of a pressure activated contact heat exchanger

A contact heat exchanger concept is being developed for use onboard Space Station as an interface device between external thermal bus and pressurized modules. The concept relies on mechanical contact activated by the fluid pressure inside thin-walled tubes. Structural testings were carried out to confirm the technology feasibility of using such thin-walled tubes. The test results also verified the linear elastic stress analysis which was used to predict the tube mechanical behaviors. A preliminary thermal testing was also performed with liquid Freon-11 flowing inside tubes and heat being supplied by electrical heating from the bottom of the contact heat exchanger baseplate. The test results showed excellent agreement of test data with analytical prediction for all thermal resistances except for the two-phase flow characteristics. Testing with two-phase flow inside tubes will, however, be performed on the NASA-JSC test bed.

Lee, C. Y.↗
NASA NTRS1988

Eddies, streams, and convergence zones in turbulent flows

Recent studies of turbulent shear flows have shown that many of their important kinematical and dynamical properties can be more clearly understood by describing the flows in terms of individual events or streamline patterns. These events or flow regions are studied because they are associated with relatively large contributions to certain average properties of the flow, for example kinetic energy, Reynolds stress, or to particular processes in the flow, such as mixing and chemical reactions, which may be concentrated at locations where streamlines converge for fast chemical reactions (referred to as convergence or C regions), or in recirculating eddying regions for slow chemical reactions. The aim of this project was to use the numerical simulations to develop suitable criteria for defining these eddying or vortical zones. The C and streaming (S) zones were defined in order to define the whole flow field. It is concluded that homogeneous and sheared turbulent flow fields are made up of characteristic flow zones: eddy, C, and S zones. A set of objective criteria were found which describe regions in which the streamlines circulate, converge or diverge, and form high streams of high velocity flow.

Hunt, J. C. R.↗
NASA NTRS1988

Three dimensional simulation of an underexpanded jet interacting with a supersonic cross flow

A new three-dimensional computational fluid dynamics (CFD) code has been developed to simulate the flow fields of an underexpanded jet transversely injected into supersonic air stream inside the combustors of ramjets and scramjets. The code employs an implicit finite volume, lower-upper (LU) time marching method to solve the complete three-dimensional Navier-Stokes equations in a fully-coupled and very efficient manner. Results clearly depict the flow characteristics, including the shock structure, separated flow regions around the injector, and the wake flow in the lee of the injector.

Yu, Sheng-Tao↗
NASA NTRS1989

Three-dimensional calculation of supersonic reacting flows using an LU scheme

A new three-dimensional numerical program incorporated with comprehensive real gas property models has been developed to simulate supersonic reacting flows. The code employs an implicit finite volume, Lower-Upper (LU) time-marching method to solve the complete Navier-Stokes and species equations in a fully-coupled and very efficient manner. A chemistry model with nine species and eighteen reaction steps are adopted in the program to represent the chemical reaction of H2 and air. To demonstrate the capability of the program, flow fields of underexpanded hydrogen jets transversely injected into supersonic air stream inside the combustors of scramjets are calculated. Results clearly depict the flow characteristics, including the shock structure, separated flow regions around the injector, and the distribution of the combustion products.

Yu, Sheng-Tao↗
NASA NTRS1989

Three-dimensional calculation of supersonic reacting flows using an LU scheme

A new three-dimensional numerical program incorporated with comprehensive real gas property models was developed to simulate supersonic reacting flows. The code employs an implicit finite volume, Lower-Upper (LU) time-marching method to solve the complete Navier-Stokes and species equations in a fully-coupled and very efficient manner. A chemistry model with nine species and eighteen reaction steps are adopted in the program to represent the chemical reaction of H2 and air. To demonstrate the capability of the program, flow fields of underexpanded hydrogen jets transversely injected into supersonic air stream inside the combustors of scramjets are calculated. Results clearly depict the flow characteristics, including the shock structure, separated flow regions around the injector, and the distribution of the combustion products.

Yu, Sheng-Tao↗
NASA NTRS2004

Fixed Packed Bed Reactors in Reduced Gravity

We present experimental data on flow pattern transitions, pressure drop and flow characteristics for cocurrent gas-liquid flow through packed columns in microgravity. The flow pattern transition data indicates that the pulse flow regime exists over a wider range of gas and liquid flow rates under microgravity conditions compared to 1-g and the widely used Talmor map in 1-g is not applicable for predicting the transition boundaries. A new transition criterion between bubble and pulse flow in microgravity is proposed and tested using the data. Since there is no static head in microgravity, the pressure drop measured is the true frictional pressure drop. The pressure drop data, which has much smaller scatter than most reported 1-g data clearly shows that capillary effects can enhance the pressure drop (especially in the bubble flow regime) as much as 200% compared to that predicted by the single phase Ergun equation. The pressure drop data are correlated in terms of a two-phase friction factor and its dependence on the gas and liquid Reynolds numbers and the Suratman number. The influence of gravity on the pulse amplitude and frequency is also discussed and compared to that under normal gravity conditions. Experimental work is planned to determine the gas-liquid mass transfer coefficients. Because of enhanced interfacial effects, we expect the gas-liquid transfer coefficients k(L)a and k(G)a (where a is the gas-liquid interfacial area) to be higher in microgravity than in normal gravity at the same flow conditions. This will be verified by gas absorption experiments, with and without reaction in the liquid phase, using oxygen, carbon dioxide, water and dilute aqueous amine solutions. The liquid-solid mass transfer coefficient will also be determined in the bubble as well as the pulse flow regimes using solid benzoic acid particles in the packing and measuring their rate of dissolution. The mass transfer coefficients in microgravity will be compared to those in normal gravity cocurrent flow to determine the mass transfer enhancement and propose new mass transfer correlations for two-phase gas-liquid flows through packed beds in microgravity.

Motil, Brian J.↗
NASA NTRS2004

Fixed Packed Bed Reactors in Reduced Gravity

We present experimental data on flow pattern transitions, pressure drop and flow characteristics for cocurrent gas-liquid flow through packed columns in microgravity. The flow pattern transition data indicates that the pulse flow regime exists over a wider range of gas and liquid flow rates under microgravity conditions compared to 1-g and the widely used Talmor map in 1-g is not applicable for predicting the transition boundaries. A new transition criterion between bubble and pulse flow in microgravity is proposed and tested using the data. Since there is no static head in microgravity, the pressure drop measured is the true frictional pressure drop. The pressure drop data, which has much smaller scatter than most reported 1-g data clearly shows that capillary effects can enhance the pressure drop (especially in the bubble flow regime) as much as 200% compared to that predicted by the single phase Ergun equation. The pressure drop data are correlated in terms of a two-phase friction factor and its dependence on the gas and liquid Reynolds numbers and the Suratman number. The influence of gravity on the pulse amplitude and frequency is also discussed and compared to that under normal gravity conditions. Experimental work is planned to determine the gas-liquid and liquid-solid mass transfer coefficients. Because of enhanced interfacial effects, we expect the gas-liquid transfer coefficients kLa and kGa (where a is the gas-liquid interfacial area) to be higher in microgravity than in normal gravity at the same flow conditions. This will be verified by gas absorption experiments, with and without reaction in the liquid phase, using oxygen, carbon dioxide, water and dilute aqueous amine solutions. The liquid-solid mass transfer coefficient will also be determined in the bubble as well as the pulse flow regimes using solid benzoic acid particles in the packing and measuring their rate of dissolution. The mass transfer coefficients in microgravity will be compared to those in normal gravity cocurrent flow to determine the mass transfer enhancement and propose new mass transfer correlations for two-phase gas-liquid flows through packed beds in microgravity.

Motil, Brian J.↗
NASA NTRS2005

NASA Langley Low Speed Aeroacoustic Wind Tunnel: Background Noise and Flow Survey Results Prior to FY05 Construction of Facilities Modifications

The NASA Langley Research Center Low Speed Aeroacoustic Wind Tunnel is a premier facility for model-scale testing of jet noise reduction concepts at realistic flow conditions. However, flow inside the open jet test section is less than optimum. A Construction of Facilities project, scheduled for FY 05, will replace the flow collector with a new design intended to reduce recirculation in the open jet test section. The reduction of recirculation will reduce background noise levels measured by a microphone array impinged by the recirculation flow and will improve flow characteristics in the open jet tunnel flow. In order to assess the degree to which this modification is successful, background noise levels and tunnel flow are documented, in order to establish a baseline, in this report.

Booth, Earl R., Jr.↗
NASA NTRS1978

Noise characteristics of upper surface blown configurations: Summary

A systematic experimental program was conducted to develop a data base for the noise and related flow characteristics of upper surface blown configurations. The effect of various geometric and flow parameters was investigated experimentally. The dominant noise was identified from the measured flow and noise characteristics to be generated downstream of the trailing edge. The possibilities of noise reduction techniques were explored. An upper surface blown (USB) noise prediction program was developed to calculate noise levels at any point and noise contours (footprints). Using this noise prediction program and a cruise performance data base, aircraft design studies were conducted to integrate low noise and good performance characteristics. A theory was developed for the noise from the highly sheared layer of a trailing edge wake. Theoretical results compare favorably with the measured noise of the USB model.

Reddy, N. N.↗
NASA NTRS2000

Mixing and NOx Emission Calculations of Confined Reacting Jet Flows in Cylindrical and Annular Ducts

Rapid mixing of cold lateral jets with hot cross-stream flows in confined configurations is of practical interest in gas turbine combustors as it strongly affects combustor exit temperature quality, and gaseous emissions in for example rich-lean combustion. It is therefore important to further improve our fundamental understanding of the important processes of dilution jet mixing especially when the injected jet mass flow rate exceeds that of the cross-stream. The results reported in this report describe some of the main flow characteristics which develop in the mixing process in a cylindrical duct. A three-dimensional computational fluid dynamics (CFD) code has been used to predict the mixing flow field characteristics and NOx emission in a quench section of a rich-burn/quick-mix/lean-burn (RQL) combustor. Sixty configurations have been analyzed in both circular and annular geometries in a fully reacting environment simulating the operating condition of an actual RQL gas turbine combustion liner. The evaluation matrix was constructed by varying the number of orifices per row and orifice shape. Other parameters such as J (momentum-flux ratio), MR (mass flowrate ratio), DR (density ratio), and mixer sector orifice ACd (effective orifice area) were maintained constant throughout the entire study. The results indicate that the mixing flow field can be correlated with the NOx production if they are referenced with the stoichiometric equivalence ratio value and not the equilibrium value. The mixing flowfields in both circular and annular mixers are different. The penetration of equal jets in both annular and circular geometries is vastly different which significantly affects the performance of the mixing section. In the computational results with the circular mixer, most of the NOx formation occurred behind the orifice starting at the orifice wake region. General trends have been observed in the NOx production as the number of orifices is changed and this appears to be common for all hole configurations and mixer types (circular or annular). The performance of any orifice shape (in producing minimum NOx) appears to be acceptable if the number of orifices can be freely varied in order to attain the optimum jet penetration.

Oechsle, Victor L.↗
NASA NTRS1994

Use of Navier-Stokes methods for the calculation of high-speed nozzle flow fields

Flows through three reference nozzles have been calculated to determine the capabilities and limitations of the widely used Navier-Stokes solver, PARC. The nozzles examined have similar dominant flow characteristics as those considered for supersonic transport programs. Flows from an inverted velocity profile (IVP) nozzle, an under expanded nozzle, and an ejector nozzle were examined. PARC calculations were obtained with its standard algebraic turbulence model, Thomas, and the two-equation turbulence model, Chien k-epsilon. The Thomas model was run with the default coefficient of mixing set at both 0.09 and a larger value of 0.13 to improve the mixing prediction. Calculations using the default value substantially underpredicted the mixing for all three flows. The calculations obtained with the higher mixing coefficient better predicted mixing in the IVP and underexpanded nozzle flows but adversely affected PARC's convergence characteristics for the IVP nozzle case. The ejector nozzle case did not converge with the Thomas model and the higher mixing coefficient. The Chien k-epsilon results were in better agreement with the experimental data overall than were those of the Thomas run with the default mixing coefficient, but the default boundary conditions for k and epsilon underestimated the levels of mixing near the nozzle exits.

Georgiadis, Nicholas J.↗