Results for “Fluid drag” — Page 15

NASA NTRS1997

Enhanced Control Effector Designs for Airbreathing Transatmospheric Vehicles

A study was conducted to evaluate the potential effectiveness of a moveable cowl-trailing-edge design for airbreathing hypersonic single-stage-to-orbit (SSTO) configurations, which can be extended or deflected from the nominal position in order to provide additional pitching moment capability. This additional pitching moment capability may reduce the necessary deflection angle from conventional control surfaces and the associated trim drag penalty. Calculations for a generic SSTO configuration with baseline and modified cowl trailing edge geometries were performed at Mach 6 and 10 initially with an engineering analysis code in order to examine several design parametrics. In order to more accurately model geometries and flow physics, 2-D viscous computational fluid dynamics (CFD) predictions were obtained. FInally, a limited set of 3D CFD predictions were obtained at Mach 6 in order to show the effects of modeling 3D flow fields as well as the full 3D vehicle geometry. Comparisons of aftbody surface pressures and force and moment predictions show differences between initial predictions and 2-D CFD solutions due to geometry modeling and calculation method differences. The 3-D CFD predictions confirm the trends observed in the 2-D solutions and provide additional information on 3D effects. These analyses shows that cowl-trailing-edge extensions were effective in providing additional (nose-down) pitching moment increments as well as increased thrust compared to the baseline geometry. These effects reduce the control surface deflection angle required to trim the vehicle and the associated trim drag. Cowl-trailingedge deflections were not as effective, generating more nose-up pitching moment and decreased thrust compared to non-deflected cases.

Cockrell, Charles E.↗

NASA NTRS1994

Development and application of computational aerothermodynamics flowfield computer codes

Research was performed in the area of computational modeling and application of hypersonic, high-enthalpy, thermo-chemical nonequilibrium flow (Aerothermodynamics) problems. A number of computational fluid dynamic (CFD) codes were developed and applied to simulate high altitude rocket-plume, the Aeroassist Flight Experiment (AFE), hypersonic base flow for planetary probes, the single expansion ramp model (SERN) connected with the National Aerospace Plane, hypersonic drag devices, hypersonic ramp flows, ballistic range models, shock tunnel facility nozzles, transient and steady flows in the shock tunnel facility, arc-jet flows, thermochemical nonequilibrium flows around simple and complex bodies, axisymmetric ionized flows of interest to re-entry, unsteady shock induced combustion phenomena, high enthalpy pulsed facility simulations, and unsteady shock boundary layer interactions in shock tunnels. Computational modeling involved developing appropriate numerical schemes for the flows on interest and developing, applying, and validating appropriate thermochemical processes. As part of improving the accuracy of the numerical predictions, adaptive grid algorithms were explored, and a user-friendly, self-adaptive code (SAGE) was developed. Aerothermodynamic flows of interest included energy transfer due to strong radiation, and a significant level of effort was spent in developing computational codes for calculating radiation and radiation modeling. In addition, computational tools were developed and applied to predict the radiative heat flux and spectra that reach the model surface.

Venkatapathy, Ethiraj↗

NASA NTRS1977

Study of dynamics of minor constituents in the thermosphere

The global distribution of helium and argon in the terrestrial thermosphere is described. It is based on the extension of a three-dimensional single-fluid numerical model of the thermosphere previously developed by the authors to treat the dynamics of a minor gas imbedded in a background gas made up of N2, O2, and O. Empirical models of the upper atmosphere, based on satellite drag and mass spectrometer data, are used to specify the background gas density and temperature as functions of altitude, latitude, and local time for a given day of the year. Effects of solar activity, eddy diffusion, and exospheric transport on the global distribution of minor gases are investigated.

Straus, J. M.↗

NASA NTRS1980

Analytical and design techniques for drag reduction studies on wavy surfaces

Numerical models for two dimensional turbulent boundary layers over wavy surfaces were investigated. Computations for wavy wall boundary layers indicate possibilities of overall drag reduction in a parameter range of the geometry of the wall. The correction technique using integral methods for analyzing arbitrary surfaces was found to be unsuitable for some cases of interest in drag reduction; a Navier-Stokes solver for wavy walls was built to test these problems. Test results of the Navier-Stokes solver indicate that the solution techniques are accurate enough to handle complex geometries and steep variations in fluid properties.

Balasubramanian, R.↗

NASA NTRS1951

On motion of fluid in boundary layer near line of intersection of two planes

In the paper "The Mutual Interference of Boundary Layers," the authors investigated the problem of the interference of two planes intersecting at right angles on the boundary layers formed by the motion of fluid along the line of intersection of these planes. In the present paper, the results of the preceding one are generalized to the case of planes intersecting at any angle. The motion of a fluid in an angle less than 180 degrees is discussed and the enlargement of the boundary layers near the line of intersection of the planes, the limits of the interference effects of the boundary layers, and the corrections on the drag are determined. All computations are conducted by the Karman-Pohlhausen method for laminar and turbulent boundary layers. The results are reduced to tabulated form.

BOUNDARY LAYER - PLATES↗

NASA NTRS1999

Experimental Results of the 2.7% Reference H Nacelle Airframe Interference High Speed Civil Transport Model

Experiments were conducted in the NASA Ames 9-Ft by 7-Ft Supersonic and 11-Ft by 11-Ft Transonic Wind Tunnels of a 2.7% Reference H (Ref. H) Nacelle Airframe Interference (NAI) High Speed Civil Transport (HSCT) model. NASA Ames did the experiment with the cooperation and assistance of Boeing and McDonnell Douglas. The Ref. H geometry was designed by Boeing. The model was built and tested by NASA under a license agreement with Boeing. Detailed forces and pressures of individual components of the configuration were obtained to assess nacelle airframe interference through the transonic and supersonic flight regime. The test apparatus was capable of measuring forces and pressures of the Wing body (WB) and nacelles. Axisymmetric and 2-D inlet nacelles were tested with the WB in both the in-proximity and captive mode. The in-proximity nacelles were mounted to a nacelle support system apparatus and were individually positioned. The right hand nacelles were force instrumented with flow through strain-gauged balances and the left hand nacelles were pressure instrumented. Mass flow ratio was varied to get steady state inlet unstart data. In addition, supersonic spillage data was taken by testing the 2-D inlet nacelles with ramps and the axisymmetric inlet nacelles with an inlet centerbody for the Mach condition of interest. The captive nacelles, both axisymmetric and 2-D, were attached to the WB via diverters. The captive 2-D inlet nacelle was also tested with ramps to get supersonic spillage data. Boeing analyzed the data and showed a drag penalty of four drag counts for the 2-D compared with the axisymmetric inlet nacelle. Two of the four counts were attributable to the external bevel designed into the 2-D inlet contour. Boeing and McDonnell Douglas used these data for evaluating Computational Fluid Dynamic (CFD) codes and for evaluation of nacelle airframe integration problems and solutions.

Cappuccio, Gelsomina↗

NASA NTRS1983

Cumulus clouds - Interactions between laboratory experiments and observations as foundations for models

Early Woods Hole cumulus observations conducted with the aid of an aircraft suggested that buoyancy dilution by entrainment was a major brake upon tropical cumulus growth. The mechanism by which entrainment occurred, however, was not well understood. Ludlam and Scorer (1953) postulated that buoyant bubbles were the building blocks of cumulus clouds and that it was aerodynamic drag which caused the tops to cease rising. The present investigation is concerned with laboratory experiments and analyses which have been conducted to clarify remaining questions. Attention is given to bubbles in water of uniform density, bubbles released into stably stratified fluids, bubbles released into a two-layer fluid, some observational questions, and buoyant plumes and thermals. The considered experiments provide some insight concerning the mechanism involved in the conversion of buoyancy into motion, taking into account a simpler fluid situation.

Simpson, J.↗

NASA NTRS1985

Relative advantages of thin-layer Navier-Stokes and interactive boundary-layer procedures

Numerical procedures for solving the thin-shear-layer Navier-Stokes equations and for the interaction of solutions to inviscid and boundary-layer equations are described and evaluated. To allow appraisal of the numerical and fluid dynamic abilities of the two schemes, they have been applied to one airfoil as a function of angle of attack at two slightly different Reynolds numbers. The NACA 0012 airfoil has been chosen because it allows comparison with measured lift, drag, and moment and with surface-pressure distributions. Calculations have been performed with algebraic eddy-viscosity formulations, and they include consideration of transition. The results are presented in a form that allows easy appraisal of the accuracy of both procedures and of the relative costs. The interactive procedure is computationally efficient but restrictive relative to the thin-layer Navier-Stokes procedure. The latter procedure does a better job of predicting drag than does the former. In both procedures, the location of transition is crucial for accurate or detailed computations, particularly at high angles of attack. When the upstream influence of pressure field through the shear layer is important, the thin-layer Navier-Stokes procedure has an edge over the interactive procedure.

Mehta, U.↗

NASA NTRS1986

A comparison of interactive boundary-layer and thin-layer Navier-Stokes procedures

Numerical procedures for solving the thin-shear-layer Navier-Stokes equations and for the interaction of solutions to inviscid and boundary-layer equations are described and evaluated. To allow appraisal of the numerical and fluid dynamic abilities of the two schemes, they have been applied to one airfoil as a function of angle of attack at two slightly different Reynolds numbers. The NACA 0012 airfoil has been chosen because it allows comparison with measured lift, drag, and moment and with surface-pressure distributions. Calculations have been performed with algebraic eddy-viscosity formulations, and they include consideration of transition. The results are presented in a form that allows easy appraisal of the accuracy of both procedures and of the relative costs. The interactive procedure is computationally efficient but restrictive relative to the thin-layer Navier-Stokes procedure. The latter procedure does a better job of predicting drag than does the former. In both procedures, the location of transition is crucial for accurate or detailed computations, particularly at high angles of attack. When the upstream influence of pressure field through the shear layer is important, the thin-layer Navier-Stokes procedure has an edge over the interactive procedure.

Mehta, U.↗

NASA NTRS1991

Suppression of pressure oscillations in an open cavity by passive pneumatic control

A computational investigation has been conducted to determine the effectiveness of a passive control technique in suppressing the oscillations in an open cavity exposed to a supersonic flow. Time-accurate solutions of the unsteady, Reynolds-averaged, Navier-Stokes equations were obtained with an explicit predictor-corrector algorithm; the passive control was implemented through the use of a simple linear pressure-velocity law along the porous cavity floor. The computational code was validated by comparisons with experimental data for the cavity flow without control. The computational results with control demonstrate that the oscillations are suppressed; the fluid dynamic mechanism of the control is seen to be a stabilization of the free-shear layer. Spectral analysis of the unsteady data shows that the resonant frequencies are essentially unchanged by the control. Beneficial reductions in the cavity resonant drag are also observed.

Chokani, N.↗

NASA NTRS1994

Geometry of thin liquid sheet flows

Incompresible, thin sheet flows have been of research interest for many years. Those studies were mainly concerned with the stability of the flow in a surrounding gas. Squire was the first to carry out a linear, invicid stability analysis of sheet flow in air and compare the results with experiment. Dombrowski and Fraser did an experimental study of the disintegration of sheet flows using several viscous liquids. They also detected the formulation of holes in their sheet flows. Hagerty and Shea carried out an inviscid stability analysis and calculated growth rates with experimental values. They compared their calculated growth rates with experimental values. Taylor studied extensively the stability of thin liquid sheets both theoretically and experimentally. He showed that thin sheets in a vacuum are stable. Brown experimentally investigated thin liquid sheet flows as a method of application of thin films. Clark and Dumbrowski carried out second-order stability analysis for invicid sheet flows. Lin introduced viscosity into the linear stability analysis of thin sheet flows in a vacuum. Mansour and Chigier conducted an experimental study of the breakup of a sheet flow surrounded by high-speed air. Lin et al. did a linear stability analysis that included viscosity and a surrounding gas. Rangel and Sirignano carried out both a linear and nonlinear invisid stability analysis that applies for any density ratio between the sheet liquid and the surrounding gas. Now there is renewed interest in sheet flows because of their possible application as low mass radiating surfaces. The objective of this study is to investigate the fluid dynamics of sheet flows that are of interest for a space radiator system. Analytical expressions that govern the sheet geometry are compared with experimental results. Since a space radiator will operate in a vacuum, the analysis does not include any drag force on the sheet flow.

Chubb, Donald L.↗

NASA NTRS2002

Synthetic Jet Interaction With A Turbulent Boundary Layer Flow

Perhaps one of the more notable advances to have occurred in flow control technology in the last fifteen years is the application of surface-issuing jets for separation control on aerodynamic surfaces. The concept was introduced by Johnston and Night (1990) who proposed using circular jets, skewed and inclined to the wall, to generate streamwise vortices for the purpose of mitigating boundary layer separation. The skew and inclination angles have subsequently been shown to affect the strength and sign of the ensuing vortices. With a non-circular orifice, in addition to skew and inclination, the yaw angle of the major axis of the orifice can influence the flow control effectiveness of the jet. In particular, a study by Chang arid Collins (1997) revealed that a non-circular orifice, yawed relative to the freestream, can be used to control the size and strength of the vortices produced by the control jet. This early work used jets with only a steady injection of mass. Seifert et al. revealed that an unsteady blowing jet, could be as effective at separation control as a steady jet but with less mass flow. Seifert et al. showed that small amplitude blowing oscillations superimposed on a low momentum steady jet Was the most effective approach to delaying separation on a NACA 0015 airfoil at post-stall angles of attack. More recent work suggests that perhaps the most efficient jet control effect comes from a synthetic (oscillatory) jet where the time-averaged mass flux through the orifice is zero, but the net wall normal momentum is non-zero. The control effectiveness of synthetic jets has been demonstrated for several internal and external flow fields used synthetic jet control on a thick, blunt-nosed airfoil to delay stall well beyond the stall angles for the uncontrolled airfoil and with a dramatic increase in the lift-to-drag performance. Amitay et al. used an array of synthetic jets to mitigate flow separation in curved and diffusing ducts. While the control effectiveness of synthetic jet actuators in an application setting has been confirmed through a number of studies, the fluid dynamic mechanism by which control is effected is not well understood. Issues like yaw angle arid velocity ratio that have been studied for steady control jets have not been investigated for synthetic jets. Moreover, the role played by the inherently unsteady nature of a synthetic jet in the interaction with the controlled flow is not known. Some recent work by Rinehart and Glazer and Smith suggests that away from tile immediate vicinity of the jet orifice the flow field is steady in the mean, and that the interaction of a synthetic jet and a boundary layer creates a secondary flow in the boundary layer consisting primarily of streamwise vortices.

Smith, Douglas R.↗

NASA NTRS1997

Aerodynamics of the Mars Microprobe Entry Vehicles

The selection of the unique aeroshell shape for the Mars Microprobes is discussed. A description of its aerodynamics in hypersonic rarefied, hypersonic continuum, supersonic and transonic flow regimes is then presented. This description is based on Direct Simulation Monte Carlo analyses in the rarefied-flow regime, thermochemical nonequilibrium Computational Fluid Dynamics in the hypersonic regime, existing wind tunnel data in the supersonic and transonic regime, additional computational work in the transonic regime, and finally, ballistic range data. The aeroshell is shown to possess the correct combination of aerodynamic stability and drag to convert the probe's initial tumbling attitude and high velocity at atmospheric-interface into the desired surface-impact orientation and velocity.

Mitcheltree, R. A.↗

NASA NTRS2009

Results of the Fluid Merging Viscosity Measurement International Space Station Experiment

The purpose of FMVM is to measure the rate of coalescence of two highly viscous liquid drops and correlate the results with the liquid viscosity and surface tension. The experiment takes advantage of the low gravitational free floating conditions in space to permit the unconstrained coalescence of two nearly spherical drops. The merging of the drops is accomplished by deploying them from a syringe and suspending them on Nomex threads followed by the astronaut s manipulation of one of the drops toward a stationary droplet till contact is achieved. Coalescence and merging occurs due to shape relaxation and reduction of surface energy, being resisted by the viscous drag within the liquid. Experiments were conducted onboard the International Space Station in July of 2004 and subsequently in May of 2005. The coalescence was recorded on video and down-linked near real-time. When the coefficient of surface tension for the liquid is known, the increase in contact radius can be used to determine the coefficient of viscosity for that liquid. The viscosity is determined by fitting the experimental speed to theoretically calculated contact radius speed for the same experimental parameters. Recent fluid dynamical numerical simulations of the coalescence process will be presented. The results are important for a better understanding of the coalescence process. The experiment is also relevant to liquid phase sintering, free form in-situ fabrication, and as a potential new method for measuring the viscosity of viscous glass formers at low shear rates.

Ethridge, Edwin C.↗

NASA NTRS1976

Collected Works of Robert T. Jones

Fluid dynamic principles are applied to airfoil stability and control problems, blood pump studies, and in relativistic kinematics.

Aeronautics↗

NASA NTRS1977

A dynamical model of upper-atmospheric helium

This numerical study of the global distribution of helium in the terrestrial thermosphere is based on the extension of a three-dimensional single-fluid numerical model of the thermosphere previously developed by the authors to treat the dynamics of a minor gas imbedded in a background gas made up of N2, O2, and O. The Cira (1972) model of the upper atmosphere, based on satellite drag data, is used to specify the background gas density and temperature as functions of altitude, latitude, and local time for a given day of the year. Specific emphasis is placed on a study of the helium distribution at solstice, i.e., the 'winter helium bulge'. Effects of solar activity, eddy diffusion, and exospheric transport on the global distribution of helium are investigated. The model reproduces the general features of the winter helium bulge, including the variation of its amplitude with solar activity, as determined by comparison of data from several recent satellite-borne mass spectrometers.

Straus, J. M.↗

NASA NTRS1987

Liquid droplet radiator development status

Development of the Liquid Droplet Radiator (LDR) is described. Significant published results of previous investigators are presented, and work currently in progress is discussed. Several proposed LDR configurations are described, and the rectangular and triangular configurations currently of most interest are examined. Development of the droplet generator, collector, and auxiliary components are discussed. Radiative performance of a droplet sheet is considered, and experimental results are seen to be in very good agreement with analytical predictions. The collision of droplets in the droplet sheet, the charging of droplets by the space plasma, and the effect of atmospheric drag on the droplet sheet are shown to be of little consequence, or can be minimized by proper design. The LDR is seen to be less susceptible than conventional technology to the effects of micrometeoroids or hostile threats. The identification of working fluids which are stable in the orbital environments of interest is also made. Methods for reducing spacecraft contamination from an LDR to an acceptable level are discussed. Preliminary results of microgravity testing of the droplet generator are presented. Possible future NASA and Air Force missions enhanced or enabled by a LDR are also discussed. System studies indicate that the LDR is potentially less massive than heat pipe radiators. Planned microgravity testing aboard the Shuttle or space station is seen to be a logical next step in LDR development.

White, K. Alan, III↗

NASA NTRS1987

Liquid droplet radiator development status

Development of the Liquid Droplet Radiator (LDR) is described. Significant published results of previous investigators are presented, and work currently in progress is discussed. Several proposed LDR configurations are described, and the rectangular and triangular configurations currently of most interest are examined. Development of the droplet generator, collector, and auxiliary components are discussed. Radiative performance of a droplet sheet is considered, and experimental results are seen to be in very good agreement with analytical predictions. The collision of droplets in the droplet sheet, the charging of droplets by the space plasma, and the effect of atmospheric drag on the droplet sheet are shown to be of little consequence, or can be minimized by proper design. The LDR is seen to be less susceptible than conventional technology to the effects of micrometeoroids or hostile threats. The identification of working fluids which are stable in the orbital environments of interest is also made. Methods for reducing spacecraft contamination from an LDR to an acceptable level are discussed. Preliminary results of microgravity testing of the droplet generator are presented. Possible future NASA and Air Force missions enhanced or enabled by a LDR are also discussed. System studies indicate that the LDR is potentially less massive than heat pipe radiators. Planned microgravity testing aboard the Shuttle or space station is seen to be a logical next step in LDR development.

White, K. Alan, III↗