SEARCH · Search NASA

Results for “Flyer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1992

The Astromag superconducting magnet facility configured for a free-flying satellite

The magnet parameters of a free-flying version of Astromag and the parameters of the space cryogenic system for the magnet are presented. Consideration is given to the free-flyer version of the Astromag magnet. The diameter of the magnet, its cryostat, the satellite and the two instruments is limited by the 4.27-m shroud diameter of the Atlas IIa. The magnet coil must use a stable reliable superconductor which can carry the full magnet current at 4.2 K at a peak induction in the coil of 7.5 T. The magnet must operate in the persistent mode. The changes in the overall design and operating requirements for the free-flying-design Astromag suggest that the coils, the cryogenic system, and the charging system can be simplified without a loss of required magnet function. Attention is given to switches, trim coils, and plumbing in the low field region between the coils; the magnet charging system and the quench protection system; and cooled helium supply to the magnet gas-cooled electrical leads.

Green, M. A.↗

NASA NTRS1992

The arcing rate for a High Voltage Solar Array - Theory, experiment and predictions

All solar arrays have biased surfaces which can be exposed to the space environment. It has been observed that when the array bias is less than a few hundred volts negative then the exposed conductive surfaces may undergo arcing in the space plasma. A theory for arcing is developed on these high voltage solar arrays which ascribes the arcing to electric field runaway at the interface of the plasma, conductor and solar cell dielectric. Experiments were conducted in the laboratory for the High Voltage Solar Array (HVSA) experiment which will fly on the Japanese Space Flyer Unit (SFU) in 1994. The theory was compared in detail to the experiment and shown to give a reasonable explanation for the data. The combined theory and ground experiments were then used to develop predictions for the SFU flight.

Hastings, Daniel E.↗

NASA NTRS1991

Momentum transfer in the one-dimensional impact of spaced plates

The two-dimensional hydrocode CSQ III was used to calculate the fraction of momentum transferred from a flyer plate to a target of two spaced plates. The effect of the vaporization phase transition, as calculated with the ANEOS analytical complete three-phase equation of state, was estimated. Application of these results to the protection of spacecraft from meteoroids and orbital debris is discussed.

Abbott, R. D.↗

NASA NTRS1992

Microgravity human factors workstation development

Microgravity evaluations of workstation hardware as well as its system components were found to be very useful for determining the expected needs of the Space Station crew and for refining overall workstation design. Research at the Johnson Space Center has been carried out to provide optimal workstation design and human interface. The research included evaluations of hand controller configurations for robots and free flyers, the identification of cursor control device requirements, and the examination of anthropometric issues of workstation design such as reach, viewing distance, and head clearance.

Whitmore, Mihriban↗

NASA NTRS1992

Early use of Space Station Freedom for NASA's Microgravity Science and Applications Program

The paper describes microgravity science opportunities inherent to the restructured Space Station and presents a synopsis of the scientific utilization plan for the first two years of ground-tended operations. In the ground-tended utilization mode the Space Station is a large free-flyer providing a continuous microgravity environment unmatched by any other platform within any existing U.S. program. It is pointed out that the importance of this period of early Space Station mixed-mode utilization between crew-tended and ground-tended approaches is of such magnitude that Station-based microgravity science experiments many become benchmarks to the disciplines involved. The traffic model that is currently being pursued is designed to maximize this opportunity for the U.S. microgravity science community.

Rhome, Robert C.↗

NASA NTRS1992

Simulated meteorite impacts and volcanic explosions: Ejecta analyses and planetary implications

Past cratering studies have focused primarily on crater morphology. However, important questions remain about the nature of crater deposits. Phenomena that need to be studied include the distribution of shock effects in crater deposits and crater walls; the origin of mono- and polymict breccia; differences between local and distal ejecta; deformation induced by explosive volcanism; and the production of unshocked, high-speed ejecta that could form the lunar and martian meteorites found on the Earth. To study these phenomena, one must characterize ejecta and crater wall materials from impacts produced under controlled conditions. New efforts at LLNL simulate impacts and volcanism and study resultant deformation. All experiments use the two-stage light-gas gun facility at LLNL to accelerate projectiles to velocities of 0.2 to 4.3 km/s, including shock pressures of 0.9 to 50 GPa. We use granite targets and novel experimental geometries to unravel cratering processes in crystalline rocks. We have thus far conducted three types of simulations: soft recovery of ejecta, 'frozen crater' experiments, and an 'artificial volcano. Our ejecta recovery experiments produced a useful separation of impactites. Material originally below the projectile remained trapped there, embedded in the soft metal of the flyer plate. In contrast, material directly adjacent to the projectile was jetted away from the impact, producing an ejecta cone that was trapped in the foam recovery fixture. We find that a significant component of crater ejecta shows no signs of strong shock; this material comes from the near-surface 'interference zone' surrounding the impact site. This phenomenon explains the existence of unshocked meteorites on the Earth of lunar and martian origin. Impact of a large bolide on neighboring planets will produce high-speed, weakly shocked ejecta, which may be trapped by the Earth's gravitational field. 'Frozen crater' experiments show that the interference zone is highly localized; indeed, disaggregation does not extend beyond approx. 1.5 crater radii. A cone-shaped region extending downward from the impact site is completely disaggregated, including powdered rock that escaped into the projectile tube. Petrographic analysis of crater ejecta and wall material will be presented. Finally, study of ejecta from 0.9- and 1.3-GPa simulations of volcanic explosions reveal a complete lack of shock metamorphism. The ejecta shows no evidence of PDF's, amorphization, high-pressure phases, or mosaicism. Instead, all deformation was brittle, with fractures irregular (not planar) and most intergranular. The extent of fracturing was remarkable, with the entire sample reduced to fragments of gravel size and smaller.

Gratz, A. J.↗

NASA NTRS1992

Report of the Working Group on Space/Lunar Tradeoffs

The group discussed the advantages and disadvantages of five locations for an optical/infrared array: low-Earth orbit (LEO), Sun-synchronous Earth-orbit, geosynchronous orbit (GEO), Lagrangian points (L4 and L5), and the lunar surface. The factors affecting an array and our assessments of them are given and briefly discussed. In the discussions, two axioms are assumed: (1) Human expansion into space and to the Moon will occur; and (2) The Space Station will be constructed and operational. The major conclusion reached is that baselines of moderate size (greater than 300 m) are best done on the Moon and that large baselines (greater than 10 km) can be done only on the Moon. Three areas needing additional research were identified as follows. (1) Studies are needed on methods to steer long-baseline systems in orbit. This involves learning how to control free-flyers. It is not clear how the difficulty of control varies with orbital elevation. (2) More work is needed on the internal metrology of array systems, both orbital and lunar-surface systems.(3) We need to understand the radiation effects on detectors and electronics and learn how to mitigate them.

Source record↗

NASA NTRS1991

Manned maneuvering unit applications for automated rendezvous and capture

Automated Rendezvous and Capture (AR&C) is an important technology to multiple National Aeronautics and Space Administration (NASA) programs and centers. The recent Johnson Spacecraft Center (JSC) AR&C Quality Function Deployment (QFD) has listed on-orbit demonstration of related technologies as a near term priority. Martin Marietta has been evaluating use of the Manned Maneuvering Unit (MMU) for a low cost near term on-orbit demonstration of AR&C technologies such as control algorithms, sensors, and processors as well as system level performance. The MMU Program began in 1979 as the method of repairing the Space Shuttle (STS) Thermal Protection System (the tiles). The units were not needed for this task, but were successfully employed during three Shuttle flights in 1984: a test flight was flown in in February as proof of concept, in April the MMU participated in the Solar Max Repair Mission, and in November the MMU's returned to space to successfully rescue the two errant satellites, Westar and Palapa. In the intervening years, the MMU simulator and MMU Qualification Test Unit (QTU) have been used for Astronaut training and experimental evaluations. The Extra-Vehicular Activities (EVA) Retriever has used the QTU, in an unmanned form, as a free-flyer on the Johnson Space Center (JSC) Precision Air Bearing Floor (PABF). Currently, the MMU is undergoing recertification for flight. The two flight units were removed from storage in September, 1991 and evaluation tests were performed. The tests demonstrated that the units are in good shape with no discrepancies that would preclude further use. The Return to Flight effort is currently clearing up recertification issues and evaluating the design against the present Shuttle environments.

Brehm, Donald L.↗

NASA NTRS1990

Evolving technologies for Space Station Freedom computer-based workstations

Viewgraphs on evolving technologies for Space Station Freedom computer-based workstations are presented. The human-computer computer software environment modules are described. The following topics are addressed: command and control workstation concept; cupola workstation concept; Japanese experiment module RMS workstation concept; remote devices controlled from workstations; orbital maneuvering vehicle free flyer; remote manipulator system; Japanese experiment module exposed facility; Japanese experiment module small fine arm; flight telerobotic servicer; human-computer interaction; and workstation/robotics related activities.

Jensen, Dean G.↗

NASA NTRS1993

Spacecraft computer technology at Southwest Research Institute

Southwest Research Institute (SwRI) has developed and delivered spacecraft computers for a number of different near-Earth-orbit spacecraft including shuttle experiments and SDIO free-flyer experiments. We describe the evolution of the basic SwRI spacecraft computer design from those weighing in at 20 to 25 lb and using 20 to 30 W to newer models weighing less than 5 lb and using only about 5 W, yet delivering twice the processing throughput. Because of their reduced size, weight, and power, these newer designs are especially applicable to planetary instrument requirements. The basis of our design evolution has been the availability of more powerful processor chip sets and the development of higher density packaging technology, coupled with more aggressive design strategies in incorporating high-density FPGA technology and use of high-density memory chips. In addition to reductions in size, weight, and power, the newer designs also address the necessity of survival in the harsh radiation environment of space. Spurred by participation in such programs as MSTI, LACE, RME, Delta 181, Delta Star, and RADARSAT, our designs have evolved in response to program demands to be small, low-powered units, radiation tolerant enough to be suitable for both Earth-orbit microsats and for planetary instruments. Present designs already include MIL-STD-1750 and Multi-Chip Module (MCM) technology with near-term plans to include RISC processors and higher-density MCM's. Long term plans include development of whole-core processors on one or two MCM's.

Shirley, D. J.↗

NASA NTRS1993

Impact-induced tensional failure in rock

Planar impact experiments were employed to induce dynamic tensile failure in Bedford limestone. Rock disks were impacted with aluminum and polymethyl methacralate flyer plates at velocities of 10 to 25 m/s. This resulted in tensile stresses in the range of 11 to 160 MPa. Tensile stress durations of 0.5 and 1.3 microsec induced microcrack growth which in many experiments were insufficient to cause complete spalling of the samples. Velocity reduction, and by inference microcrack production, occurred in samples subjected to stresses above 35 MPa in the 1.3-microsec PMMA experiments and 60 MPa in the 0.5-microsec aluminum experiments. Apparent fracture toughnesses of 2.4 and 2.5 MPa m exp 1/2 are computed for the 1.3- and 0.5-microsec experiments. Three-dimensional impact experiments were conducted on 20 cm-sized blocks of Bedford limestone and San Marcos gabbro. Compressional wave velocity deficits up to 50-60 percent were observed in the vicinity of the crater. The damage decreases as about r exp -1.5 from the crater, indicating a dependence on the magnitude and duration of the tensile pulse.

Ahrens, Thomas J.↗

NASA NTRS1991

Task-analytic evaluations of Space Station Freedom workstations

Space Station Freedom will be a permanently manned multipurpose facility in low Earth orbit by the late 1990's. Integral to Space Station Freedom will be Data Management System workstations. These workstations will provide the human-machine interface for controlling such systems as Guidance, Navigation and Control, Propulsion, and Environmental Control and Life Support. In addition, they will be used by crewmembers in the space station's pressurized shirt-sleeve environment to control remote manipulator systems and free-flyer devices. This paper presents an overview of proposed workstations and current task-analytic evaluations being used to assess their adequacy in supporting Space Station Freedom operations. Particular emphasis is placed on the results and conclusions of the analysis.

Diaz, Manuel F.↗

NASA NTRS1992

Arcing rates for High Voltage Solar Arrays - Theory, experiment, and predictions

All solar arrays have biased surfaces that can be exposed to the space environment. It has been observed that when the array bias is less than a few hundred volts negative, then the exposed conductive surfaces may undergo arcing in the space plasma. A theory for arcing is developed on these high voltage solar arrays that ascribes the arcing to electric field runaway at the interface of the plasma, conductor, and solar cell dielectric. Experiments were conducted in the laboratory for the High Voltage Solar Array experiment that will fly on the Japanese Space Flyer Unit (SFU) in 1994. The theory was compared in detail with the experiment and shown to give a reasonable explanation for the data. The combined theory and ground experiments were then used to develop predictions for the SFU flight.

Hastings, Daniel E.↗

NASA NTRS1991

Low temperature research facilities for shuttle and beyond

This paper describes the Low Temperature Research Facility program now under development at the Jet Propulsion Laboratory. This program will develop the experiments and cryogenic facility to fly experiments requiring temperatures in the liquid helium range, from the superfluid range (1.6 K) to the critical point (5.2 K). A shuttle facility is planned for 1998. It will be flown about every two years after that time. A free flyer is also being evaluated for the end of the decade or early in the next century. A brief discussion of the quality of micro-gravity available in various carriers is also given.

Mason, P.↗

NASA NTRS1991

Jet ejecta mass upon oblique impact

Theoretical models in the jetting regime for symmetric and asymmetric impact of thin plates predict the mass and velocity of jetted material upon oblique impact. However, experimental constraints on the amount of material which form jets upon oblique impact are not known. A series of preliminary experiments were conducted in which tungsten (W) flyer plates at speeds of 1.5 to 2.0 km/s were obliquely impacted into carbon targets at 30 deg in the regime of jetting, yielding radiation temperatures in the about 3200 K range. Both framing-camera and flash X-ray imaging were conducted. Broad cm-sized craters induced by jet ejecta on 2024 Al witness plates were used to infer jet mass. We infer, from measured witness plate crater volumes, that jet masses in the range of 0.01 to 0.06 g are produced by a 32 mm diameter, 6 mm thick W impactor. This is about one to two orders of magnitude less than those calculated from present theoretical models. In contrast, in refractory material experiments, the mass of gabbro ejecta trapped in styrofoam is 0.52 g, which is similar to that calculated.

Yang, W.↗

NASA NTRS1954

Flight Tests of a Man Standing on a Platform Supported by a Teetering Rotor

Because previous flight tests of a man standing on a jet-supported platform were very successful, a series of flight tests were made to determine the flying qualities of a man standing on a platform supported by a teetering rotor. The rotor was 7 feet in diameter and was driven by air jets at the rotor tips fed by hollow blades and air hoses connected to an external air supply. The machine was tested with a free-teetering rotor and with a spring-restrained rotor, and, as an alternate arrangement, with the rotor and foot platform isolated from the framework by rubber connections to reduce the inertia of the moving parts. The machine was tested indoors in hovering and in limited translational flight and outdoors in light and in strong gusty winds. The stability and controllability with the spring-restrained rotor were uniformly good. The stability with the free-teetering rotor was marginal, but, when an experienced flyer placed his hands on a hand rail, the stability and controllability were good. The stability and controllability with the rubber-isolated frame and spring-restrained teetering rotor were very good and quite like the jet-supported platform.

Paul R Hill↗

NASA NTRS1936

The formation of ice on airplanes

The present report examines the problem of ice formation from the point of view of the pilot and the meteorologist. Their experiences prove the ice deposit to be first and foremost a navigational problem and only secondarily a question of de-icing devices. With correct utilization of the meteorological information by the flyer, ice hazard can in many cases be minimized or avoided. Ice formation and the different types of ice deposits are listed and discussed. Weather formation during these ice deposits are also discussed as well as the effect of ice formation on aircraft.

Noth, H↗

NASA NTRS1993

Utilization of Shuttle small payload accommodations in the DOD Space Test Program

Over the past 27 years, the U.S. Air Force, as executive agent for the Department of Defense (DOD) Space Test Program, has flown approximately 325 space experiments for the Army, Navy, Air Force, and other DOD agencies. These experiments have made significant contributions to the improvement of military technology and operations. Flight of Space Test Program experiments has been carried out utilizing free flyer spacecraft, the Space Shuttle crew cabin, and the Space Shuttle cargo bay. This paper will concentrate on those experiments which have been flown by the NASA Space Shuttle small payload flight systems, e.g., GAS, uprated GAS (CAP), and Hitchhiker flight systems. Discussions of Space Test Program experiments flown by Space Shuttle small payloads flight systems will include the experiment objectives, the accommodations and services provided by the flight systems, experiment results, and lessons learned from the planning and conduct of the flight. Particular emphasis will be placed on those experiments which required and were provided with a new and unique capability by the small payloads flight systems. These capabilities include the first use of the GAS opening lid, the first use of the GAS payload ejection capability, and the first use of the Hitchhiker cross bay carrier.

Hagler, Thomas↗