Results for “Freestream conditions” — Page 15

NASA NTRSDate not supplied

Fluid-Structure Interaction Simulations of the ASPIRE SR03 Supersonic Parachute Flight Test

Research into parachute performance continues to be a source of significant investment from the National Aeronautics and Space Administration to mitigate risks and to enable a variety of exploration missions, including landing on Mars as well as returning to Earth. The cost of flight tests to certify any changes to the current state-of-the-art parachute designs limits the development of next generation parachute systems. Fluid-structure interaction simulations could help accelerate this process once validated. The Launch, Ascent, and Vehicle Aerodynamics team is developing the capability to perform such fluid-structure interaction simulations by coupling a higher-order Cartesian immersed boundary computational fluid dynamics solver with adaptive mesh refinement to a finite element structural dynamics solver in space and time. We continue the effort to validate this tool with the Advanced Supersonic Parachute Inflation Research Experiments SR03 flight test featuring a strengthened parachute akin to the Mars 2020 mission that landed the Perseverance rover on Mars, and a higher freestream dynamic pressure prior to inflation. The effect of the flow conditions’ angle of attack and of the initial parachute shape are quantified. The impact of relaxing modeling assumptions with regards to radial stiffeners on the parachute canopy is also investigated. Results demonstrate improvements in agreement with the pull force recorded during the SR03 flight test as the initial conditions of the flow and parachute are brought closer to those experienced in flight, and further improved when the radial stiffener modeling assumptions are relaxed.

ESM↗

NASA NTRSDate not supplied

Fluid-Structure Interaction Simulations of the ASPIRE SR03 Supersonic Parachute Flight Test

Research into parachute performance continues to be a source of significant investment from the National Aeronautics and Space Administration to mitigate risks and to enable a variety of exploration missions, including landing on Mars as well as returning to Earth. The cost of flight tests to certify any changes to the current state-of-the-art parachute designs limits the development of next generation parachute systems. Fluid-structure interaction simulations could help accelerate this process once validated. The Launch, Ascent, and Vehicle Aerodynamics team is developing the capability to perform such fluid-structure interaction simulations by coupling a higher-order Cartesian immersed boundary computational fluid dynamics solver with adaptive mesh refinement to a finite element structural dynamics solver in space and time. We continue the effort to validate this tool with the Advanced Supersonic Parachute Inflation Research Experiments SR03 flight test featuring a strengthened parachute akin to the Mars 2020 mission that landed the Perseverance rover on Mars, and a higher freestream dynamic pressure prior to inflation. The effect of the flow conditions’ angle of attack and of the initial parachute shape are quantified. The impact of relaxing modeling assumptions with regards to radial stiffeners on the parachute canopy is also investigated. Results demonstrate improvements in agreement with the pull force recorded during the SR03 flight test as the initial conditions of the flow and parachute are brought closer to those experienced in flight, and further improved when the radial stiffener modeling assumptions are relaxed.

ESM↗

NASA NTRS1985

Results of the AFRSI rewaterproofing systems screening test in the NASA/Ames Research Center (ARC) 2 x 2-foot transonic wind tunnel

An experimental investigation was conducted in the NASA/Ames Research Center 2x2-foot Transonic Wind Tunnel to evaluate two AFRSI rewaterproofing systems and to investigate films as a means of reducing blanket joint distortion. The wind tunnel wall slot configuration influenced on the flow field over the test panel was investigated; primarily using oil flow data, and resulted in a closed slot configuration to provide a satisfactory screening environment flow field for the test. Sixteen AFRSI test panels, configured to represent the test system or film, were subjected to this screening environment (a flow field of separated and reattached flow at a freestream Mach numnber of 0.65 and q = 650 or 900 psf). Each condition was held until damage to the test article was observed or 55 minutes if no damage was incurred. All objectives related to AFRSI rewaterproofing and to the use of films to stiffen the blanket fibers were achieved.

Marroquin, J.↗

NASA NTRS1993

Near wake structure for a generic ASTV configuration

Results of a numerical study are presented for hypersonic low-density flow about a 70-deg blunt cone using the direct simulation Monte Carlo method. Particular emphasis is given to the near wake flow and its sensitivity to rarefaction and other parametric variations. The flow conditions simulated are attainable in existing low-density hypersonic wind tunnels; that is, Mach 20 nitrogen flow encompassing freestream Knudsen numbers of 0.03 to 0.001. A stable vortex forms in the near wake at and below a freestream Knudsen number of 0.01 and the size of the vortex increases with decreasing freestream Knudsen number. The base region of the flow remains in thermal nonequilibrium for all cases. There is no formation of a lip separation shock or a distinct wake shock at these rarefied conditions.

Dogra, Virendra K.↗

NASA NTRS1995

DSMC calculations for 70-deg blunted cone at 3.2 km/s in nitrogen

Numerical results obtained with the direct simulation Monte Carlo (DSMC) method are presented for Mach 15.6 nitrogen flow about a 70-deg spherically blunted cone at zero incidence. This flow condition is one of several generated in the Large Energy National Shock (LENS) tunnel during tests of a 15.24 cm diameter model with an afterbody sting. The freestream Knudsen number, based on model diameter, is 0.0023. The focus of the DSMC calculations is to characterize the near wake flow under conditions where rarefaction effects may influence afterbody aerothermal loads. This report provides information concerning computational details along with flowfield and surface quantities. Calculations show that the flow enveloping the test model is in thermal nonequilibrium and a sizable vortex develops in the near wake. Along the model baseplane the heating rates are about 0.6 percent of the forebody stagnation value while the maximum heating along the sting is about 4.2 percent of the forebody stagnation value. Comparison of a Navier-Stokes solution with the present calculations show good agreement for surface heating, pressure, and skin friction results.

Moss, J. N.↗

NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, Ramani↗

NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, R.↗

NASA NTRS2012

Computational Analyses of the LIMX TBCC Inlet High-Speed Flowpath

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for the high-speed flowpath and isolator of a dual-flowpath Turbine-Based Combined-Cycle (TBCC) inlet using the Wind-US code. The RANS simulations were performed in preparation for the Large-scale Inlet for Mode Transition (LIMX) model tests in the NASA Glenn Research Center (GRC) 10- by 10-ft Supersonic Wind Tunnel. The LIMX inlet has a low-speed flowpath that is coupled to a turbine engine and a high-speed flowpath designed to be coupled to a Dual-Mode Scramjet (DMSJ) combustor. These RANS simulations were conducted at a simulated freestream Mach number of 4.0, which is the nominal Mach number for the planned wind tunnel testing with the LIMX model. For the simulation results presented in this paper, the back pressure, cowl angles, and freestream Mach number were each varied to assess the performance and robustness of the high-speed inlet and isolator. Under simulated wind tunnel conditions at maximum inlet mass flow rates, the high-speed flowpath pressure rise was found to be greater than a factor of four. Furthermore, at a simulated freestream Mach number of 4.0, the high-speed flowpath and isolator showed stability for freestream Mach number that drops 0.1 Mach below the design point. The RANS simulations indicate the yet-untested highspeed inlet and isolator flowpath should operate as designed. The RANS simulation results also provided important insight to researchers as they developed test plans for the LIMX experiment in GRC s 10- by 10-ft Supersonic Wind Tunnel.

Dippold, Vance F., III↗

NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗

NASA NTRS1994

Direct numerical simulations of leading-edge receptivity for freestream sound

The objective of this paper is to review our efforts in spatial direct numerical simulations for modeling leading-edge receptivity to freestream sound and vorticity. These results begin to provide the link between the freestream and the initial boundary-layer response and can provide the upstream conditions for further simulations marching through the transition process toward turbulence.

Fuciarelli, David A.↗

NASA NTRS1993

Numerical investigation of receptivity to freestream vorticity

The receptivity to freestream vorticity of the boundary layer over a flat plate with an elliptic leading edge is studied numerically. A finite-difference scheme that is second-order accurate in both time and space is utilized to solve the incompressible Navier-Stokes system in general curvilinear coordinates with the vorticity and stream function as dependent variables. Simulations show, for the conditions considered, a linear variation in the Tollmien-Schlichting response with forcing amplitude for perturbations of freestream velocity that are either symmetrical or asymmetrical with respect to the basic state stagnation streamline.

Buter, Thomas A.↗

NASA NTRSDate not supplied

Numerical Investigation of Heat Transfer on the NASA SIDRM Model

NASA has developed a Simulated Inter-Duct Research Model (SIDRM) to study ice crystal icing in aircraft engines. A numerical investigation has been completed using the NASA in-house code, GlennHT. For each flow condition, many different wall thermal boundary conditions were imposed. Six uniform wall temperature cases were generated, with wall temperature relative to the freestream total temperature of 0.85, 0.90, 0.95, 1.05, 1.10, and 1.15. In addition, five cases with uniform heat flux were generated. Heat fluxes were chosen to generate average wall temperatures in the range explored by the uniform wall temperature cases. Included in the uniform heat flux cases is the adiabatic case where heat flux equals zero. The results of these simulations are then used to quantify the degree to which the heat transfer coefficient depends on wall thermal boundary condition. It is seen that the heat transfer coefficient is fairly independent of wall thermal boundary condition, as expected. However, it would appear that, at least in some locations, it may be prudent to attempt to correlate a variation of heat transfer coefficient with wall thermal boundary condition.

Ice Crystal Icing↗

NASA NTRS1990

The inviscid stability of supersonic flow past a sharp cone

The laminar boundary layer which forms on a sharp cone in a supersonic freestream, where lateral curvature plays a key role in the physics of the problem is considered. This flow is then analyzed from the point of view of linear, temporal, inviscid stability. The basic, non-axisymmetric disturbance equations are derived for general flows of this class, and a so called triply generalized inflexion condition is found for the existence of subsonic neutral modes of instability. This condition is analogous to the well-known generalized inflexion condition found in planar flows, although in the present case the condition depends on both axial and aximuthal wavenumbers. Extensive numerical results are presented for the stability problem at a freestream Mach number of 3.8, for a range of streamwise locations. These results reveal that a new mode of instability may occur, peculiar to flows of this type involving curvature. Additionally, asymptotic analyses valid close to the tip of the cone, far downstream of the cone are presented, and these give a partial (asymptotic) description of this additional mode of instability.

Duck, Peter W.↗

NASA NTRS1976

Compressible laminar boundary layers with large acceleration and cooling

The paper extends an approximate prediction method involving the integral form of the momentum equation to deduce the flow quantities of interest when compressibility effects become important and heat transfer may occur. The approximate method is applicable to a two-dimensional laminar boundary layer on an impermeable surface of negligible curvature for a specified integral momentum equation. The proposed approximate method involves the use of similar solutions in conjunction with the integral momentum equation for isentropic freestream flow of a perfect gas by assuming that viscosity is proportional to stagnation condition and Prandtl number is unity. The study pertains to larger values of acceleration (acceleration parameter to 20 rather than 2) than previously considered to account for rapidly accelerating flows such as in supersonic nozzles. A discussion of some applications confirms the advantages of the method in establishing better confidence in the predictions.

Back, L. H.↗

NASA NTRS1976

Similarity solution of the boundary-layer equations for laser heated flows

The laminar boundary-layer equations with local similarity approximation are solved in order to estimate the heat transfer rate to the wall in a laser-heated rocket thruster using pure hydrogen, where the average temperature of the hot plasma core is about 14,000 K and the core Reynolds number based on nozzle throat diameter is about 2000. Under these conditions, the density-viscosity product at the wall can be 10 times the freestream value, and the hydrogen is completely dissociated. Hence the boundary layer equations with variable transport properties are solved by a quasi-linearization technique, and the equilibrium properties of hydrogen are used in the calculations. Velocity profiles are obtained, and the wall shear and wall stagnation enthalpy gradient are plotted against the pressure gradient parameter.

Wu, P. K.↗

NASA NTRS1986

Hydrogen scramjet with side wall injection

Preliminary results are presented from an experimental evaluation of a hydrogen-burning wall-injection scramjet engine, performed in the free-piston shock tunnel at the Australian National University. The advantages of scramjet propulsion for high-Mach-number high-altitude flight are reviewed, and the need for an alternative to injection struts is indicated. Pressure profiles and heat-transfer measurements for constant-area and diverging ducts are presented graphically and characterized in detail. The ability of the injected flow to shield the chamber wall from the heat of the freestream flow is demonstrated. The extrapolation of the shock-tunnel results to flight conditions, however, is made difficult by the fact that a significant amount of fuel passes through a quenched zone without burning, seriously degrading overall performance.

Morgan, R. G.↗

NASA NTRS2004

Active Flow Control on a Boundary-Layer-Ingesting Inlet

Boundary layer ingestion (BLI) is explored as means to improve overall system performance for Blended Wing Body configuration. The benefits of BLI for vehicle system performance benefit are assessed with a process derived from first principles suitable for highly-integrated propulsion systems. This performance evaluation process provides framework within which to assess the benefits of an integrated BLI inlet and lays the groundwork for higher-fidelity systems studies. The results of the system study show that BLI provides a significant improvement in vehicle performance if the inlet distortion can be controlled, thus encouraging the pursuit of active flow control (AFC) as a BLI enabling technology. The effectiveness of active flow control in reducing engine inlet distortion was assessed using a 6% scale model of a 30% BLI offset, diffusing inlet. The experiment was conducted in the NASA Langley Basic Aerodynamics Research Tunnel with a model inlet designed specifically for this type of testing. High mass flow pulsing actuators provided the active flow control. Measurements were made of the onset boundary layer, the duct surface static pressures, and the mass flow through the duct and the actuators. The distortion was determined by 120 total pressure measurements located at the aerodynamic interface plane. The test matrix was limited to a maximum freestream Mach number of 0.15 with scaled mass flows through the inlet for that condition. The data show that the pulsed actuation can reduce distortion from 29% to 4.6% as measured by the circumferential distortion descriptor DC60 using less than 1% of inlet mass flow. Closed loop control of the actuation was also demonstrated using a sidewall surface static pressure as the response sensor.

Gorton, Susan Althoff↗

NASA NTRS2015

Near-Field Acoustic Power Level Analysis of F31/A31 Open Rotor Model at Simulated Cruise Conditions, Technical Report II

Near-field acoustic power level analysis of F31A31 open rotor model has been performed to determine its noise characteristics at simulated cruise flight conditions. The non-proprietary parts of the test data obtained from experiments in the 8x6 supersonic wind tunnel were provided by NASA-Glenn Research Center. The tone and broadband components of total noise have been separated from raw test data by using a new data analysis tool. Results in terms of sound pressure levels, acoustic power levels, and their variations with rotor speed, freestream Mach number, and input shaft power, with different blade-pitch setting angles at simulated cruise flight conditions, are presented and discussed. Empirical equations relating models acoustic power level and input shaft power have been developed. The near-field acoustic efficiency of the model at simulated cruise conditions is also determined. It is hoped that the results presented in this work will serve as a database for comparison and improvement of other open rotor blade designs and also for validating open rotor noise prediction codes.

Broadband↗