Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

High-toughness graphite/epoxy composite material experiment

The experiment was designed to measure the effect of near-space exposure on mechanical properties of specially toughened 5208/T300 graphite-epoxy composites. The properties measured are elastic modulus, strength, and fracture toughness. Specimens were mounted on an external frame during the time of the LDEF mission. Specimen variables include angle of adjacent plies and fraction of interlaminar contact, which is controlled by the fraction of finely spaced holes in Mylar film placed between the prepreg monolayers of the composite.

Felbeck, David K.↗

Graphite Specimen Mass Measurements for NESHAP Calculations

The Advanced Graphite Creep (AGC) experiments were designed to irradiate various types of graphite specimens to gain an understanding of how the physical and thermal properties of the graphite change. The graphite specimens are machined from nuclear grade graphite that is very pure relative to other graphite types. However, it still contains parts per million (PPM) levels of metal contaminants that are dispersed throughout it. During irradiation in the Advanced Test Reactor (ATR) these metal contaminants become activated resulting in the graphite specimens being classified as a radioactive material. Following their irradiation, a variety of measurements and experiments are performed on these specimens that require them to be heated above 100°C.Whenever a radioactive material is heated to above 100°C the National Emission Standards for Hazardous Air Pollutants (NESHAP) calculations require the activity content, in Curies, of the isotopes that could potentially be released to the environment. The purpose of this ECAR is to document the method by which the mass loss of each sample is determined and how the isotopic content of this mass loss is determined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The importance of defects for carbon nanoribbon based electronics

The utilization of graphene nanoribbons for next generation nanoelectronics is commonly expected to depend on controlled synthesis that yields a low density of defects. Edge roughness and vacancies have been shown to have large impact on the performance of graphene nanoribbon transistors. In fact, we show how certain defects can be used to enhance the electronic and magnetic properties of graphene nanoribbons. We explore the properties of hybrid graphene nanoribbons with armchair and zigzag features joined by an array of pentagon-heptagon structural defects. The graphene nanoribbons display an increased density of states at the Fermi level, and half metallicity in absence of external fields.

36 MATERIALS SCIENCE↗

Properties of autoclaved Gr/PI composites made from improved tack PMR-15 prepreg

Autoclave processing studies were conducted, using improved tack PMR-15 prepreg, to determine the effect of tack enhancing PMR resin modifications on composite processability and mechanical properties. Improved tack graphite fiber reinforced PMR-15 prepregs were prepared and exposed to ambient conditions for various times and then autoclave molded into composites. Composite specimens were prepared and tested for flexural and interlaminar shear strengths at room temperature and 316 C. The retention of flexural and interlaminar shear strength as a function of exposure in air at 316 C was also determined. The results show that the modified PMR resin solutions provide prepreg with improved tack and drape retention characteristics without adversely affecting processability or mechanical properties of autoclave molded graphite fiber reinforced PMR-15 composites.

Vannucci, R. D.↗

Irradiation-Induced Defect Evolution in Nuclear Graphite

Graphite has historically been used as a moderator material in nuclear reactor designs dating back to the first man-made nuclear reactor to achieve criticality (Chicago Pile 1) in 1942. Additionally, graphite is a candidate material for use in the future envisioned next-generation nuclear reactors (Gen IV); specifically, the molten-salt-cooled (MSR) and very-high-temperature reactor (VHTR) concepts. Gen IV reactor concepts will introduce material challenges as temperature regimes and reactor lifetimes are anticipated to far exceed those of earlier reactors. Irradiation-induced defect evolution is a fundamental response in nuclear graphite subjected to irradiation. These defects directly influence the many property changes of nuclear graphite subjected to displacing radiation; however, a comprehensive explanation for irradiation-induced dimensional change remains elusive. The objectives of this project were focused on the characterization of irradiation-induced defect evolution in nuclear graphite via transmission electron microscopy (TEM). With the use of novel TEM specimen preparation techniques, high-temperature electron-irradiation and characterization of high-temperature neutron-irradiated nuclear graphite, novel fullerene-like defects are shown to be a dominant defect type, especially at higher temperatures. These results contradict the historical models of defect evolution and provide valuable insight into the macroscopically observed property changes in irradiated nuclear graphite.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE ART Graphite Program Intro Status 2023

General description of the ART Graphite Program with Status for 2023. This includes list of staff members, and brief description of behavior models, licensing & code, graphite R&D, As-Fab'd Properties, Machanism and Analysis, Irradiation. Also detail FY23 Activites, with AGC Update, Oxidation Activiteis, Baseline STatus, ASME Code Development, VIC Project Update, Molten salt studies. Slide included to highlight each employee contributions for work and papers and NEUPs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Graphite fiber reinforced thermoplastic resins

Mechanical properties of neat resin samples and graphite fiber reinforced samples of thermoplastic resins were characterized with particular emphasis directed to the effects of environmental exposure (humidity, temperature and ultraviolet radiation). Tensile, flexural, interlaminar shear, creep and impact strengths were measured for polysulfone, polyarylsulfone and a state-of-the-art epoxy resin samples. In general, the thermoplastic resins exhibited environmental degradation resistance equal to or superior to the reference epoxy resin. Demonstration of the utility and quality of a graphite/thermoplastic resin system was accomplished by successfully thermoforming a simulated compressor blade and a fan exit guide vane.

Novak, R. C.↗

Analysis and measurements of low frequency lightning component penetration through aerospace vehicle metal and graphite skins

An analysis of the shielding properties of mixed metal and graphite composite structures has illustrated some important aspects of electromagnetic field penetration into the interior. These include: (1) that graphite access doors on metallic structures will attenuate lightning magnetic fields very little; conversely, metal doors on a graphite structure will also attenuate fields from lightning strike currents very little, i.e., homogeneity of the shield is a critical factor in shielding and (2) that continuous conductors between two points inside a graphite skin such as an air data probe metallic tubing connection to an air data computer can allow large current penetrations into a vehicle interior. The true weight savings resulting from the use of composite materials can only be evaluated after the resulting electromagnetic problems such as current penetrations have been solved, and this generally requires weight addition in the form of cable shields, conductor bonding or external metallization.

Robb, J. D.↗

Property evaluation and microstructure characterization of the A3-3 matrix graphite - 18440

Spherical fuel elements with TRISO fuel will be used in the pebble-bed high temperature gas-cooled nuclear reactor. The fuel will be located within the center region of the elements, and will be suspended in, and surrounded by a shell of matrix graphite. The matrix graphite provides structural support to the fuel, prevents fuel damage, and allows for heat transfer from the fuel to the coolant. The raw materials for the matrix graphite, type A3-3, includes 64 wt% natural flake graphite, 16 wt% artificial graphite and 20 wt% phenol resin binder. After the final heat treatment, the resulting A3-3 matrix is composed of 71 wt% natural graphite, 18 wt% artificial graphite, and 11 wt% phenol resin-derived coke carbon. The microstructure of A3-3 matrix graphite has direct influences on the material properties, which are crucial to maintaining the integrity and safety of the fuel elements. This presentation will discuss microstructure features, such as lattice, and crystal parameters, porosity, pore size and distribution, and anisotropy. The multiple physical, mechanical and thermal properties of this material, including: elastic modulus, mechanical strength, and oxidation property will also be presented. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of counterface material type and its topography on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, R. L.↗

Counterface effects on the tribological properties of polyimide composites

Graphite fiber reinforced polyimide composite pins were slid against seven different counterfaces to determine the effect of material type on the tribological properties of polymer composites. In addition, the effect of sliding a new pin on a pre-established transfer film was investigated. The results indicated that almost a five order of magnitude difference in composite wear rate can occur just by varying the counterface material. An attempt to make all surfaces as smooth as possible was made, but due to differences in material composition this was not possible and a range of surface roughnesses were obtained. The results indicate that the smoother the surface, the lower the composite wear rate; but that small protrusions (not discernible with arithmetic surface roughness measurements) can markedly increase wear rates. A pre-established transfer film improved both run in and steady state wear rates.

Fusaro, Robert L.↗

AGC-1 Specimen Post Irradiation Data Report

Here we report the results of the Post Irradiation Examination (PIE) of the creep, control, and piggyback specimens from the irradiation creep capsule AGC-1. This is the first (prototype) of a series of six capsules planned as part of the Advanced Graphite Creep (AGC) experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphites. The data reported include: specimen dimensions and hence the dimensional change upon irradiation (a comparison of these data for specimen matched pairs will yield the creep strain); mass and volume, hence density; elastic constants (Young’s modulus, shear modulus and Poisson’s ratio) from ultrasonic time of flight (TOF) and velocity measurements; Young’s modulus from the fundamental frequency of vibration; electrical resistivity; and thermal expansion from 100-550°C (hence coefficient of thermal expansion). Over 8500 individual physical measurement have been made and the data are reduced and reported here. The AGC-1 capsule was irradiated in the Advanced Test Reactor (ATR) at INL at approximately 700°C and to a peak dose of 7 dpa (displacements per atom). The specimen’s final dose, temperature and stress conditions have been reported by INL and are also tabulated here. Additionally the analysis of the SiC temperature monitors is reported. These temperature monitors were located along the center of the AGC-1 capsule and provide an independent assessment of the capsules final irradiation temperature. While all the PIE testing is reported (with the exception of the glued-end tensile strength specimens) additional analysis of the AGC data will be required to allow: 1. Improved fits to the existing models of graphite irradiation induced creep strain. 2. With the eventual advent of temperature dependency data from the additional AGC series of capsules, and microstructural data from piggy back specimens in AGC capsules, the development of new and improved models for the development of irradiation induced creep strain in graphite are anticipated. 3. An Investigation into the effects of creep strain on the physical properties of irradiated graphite.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Fundamental analysis of the failure of polymer-based fiber reinforced composites

A mathematical model is described which will permit predictions of the strength of fiber reinforced composites containing known flaws to be made from the basic properties of their constituents. The approach was to embed a local heterogeneous region (LHR) surrounding the crack tip into an anisotropic elastic continuum. The model should (1) permit an explicit analysis of the micromechanical processes involved in the fracture process, and (2) remain simple enough to be useful in practical computations. Computations for arbitrary flaw size and orientation under arbitrary applied load combinations were performed from unidirectional composites with linear elastic-brittle constituent behavior. The mechanical properties were nominally those of graphite epoxy. With the rupture properties arbitrarily varied to test the capability of the model to reflect real fracture modes in fiber composites, it was shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting can all occur during a period of (gradually) increasing load prior to catastrophic fracture. The computations reveal qualitatively the sequential nature of the stable crack process that precedes fracture.

Kanninen, M. F.↗

Voltammetric determination of vitamin B{sub 6} (pyridoxine) at a graphite screen-printed electrode modified with graphene oxide/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite

The preparation and study of electrochemical properties of a graphite screen-printed electrode (SPE) modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} (GO is graphene oxide) nanocomposites are described. The morphologies of the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposites were examined by scanning electron microscopy. The electrochemical oxidation of vitamin B{sub 6} (pyridoxine) on SPE modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite was investigated by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. Under optimum conditions (pH 7.0), the vitamin B{sub 6} oxidation at the surface of the modified SPE occurs at a potential about 190 mV less positive than that at the unmodified SPE. A linear voltammetric response for vitamin B{sub 6} was obtained in the concentration range 1.0•10 {sup 6}—9.0•10 {sup 4} mol L{sup –1} with a detection limit of 5.2•10 {sup 7} mol L{sup –1} using differential pulse voltammetry. The developed sensor was also successfully applied for determination of trace level of vitamin B{sub 6} in both the standard vitamin B{sub 6} sample and biological samples (urine).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Stiffness Properties for Dynamic Modeling of Composite Graphite-Epoxy Cylindrical Orthotropic Shells

Traditional composite lamination theory was used to predict composite graphite-epoxy laminate stiffnesses for comparison to quasi-experimental stiffnesses developed from cylindrical bottle pressure testing. Stiffness sensitivities were examined for variations in constituent materials and geometric properties. The material component interactions examined were the fiber longitudinal and transverse Young's modulus, the fiber shear modulus and primary Poisson's ratio, the resin Young's modulus, shear modulus, and Poisson's ratio. The geometric variation of the helical winding angle was also examined. Two computer programs were written to generate the data used to demonstrate the stiffness variations.

Tolbert, R. N.↗

Technical assessment for quality control of resins

Survey visits to companies involved in the manufacture and use of graphite-epoxy prepregs were conducted to assess the factors which may contribute to variability in the mechanical properties of graphite-epoxy composites. In particular, the purpose was to assess the contributions of the epoxy resins to variability. Companies represented three segments of the composites industry - aircraft manufacturers, prepreg manufacturers, and epoxy resin manufacturers. Several important sources of performance variability were identified from among the complete spectrum of potential sources which ranged from raw materials to composite test data interpretation.

Gosnell, R. B.↗