Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Transportability of a laser-induced fluorescence calibration for NO at high pressure

Obtaining quantitative measurements of NO concentration via laser-induced fluorescence (LIF) at high pressure requires application of a suitable calibration. While it is best to calibrate as close to the measurement condition as possible, this is not always feasible. To assess the transportability of a calibration factor at high pressure, we have calculated ratios between linear LIF signals corresponding to a constant NO concentration at different measurement and calibration conditions for high-pressure ethane flames. We find that pressure broadening limits the utility of calibrating at a pressure different from that of the measurement, although a calibration performed at a higher pressure is applicable over a wider range of pressures than one performed at atmospheric pressure. If one calibrates at the same pressure, it is best to calibrate at a temperature within 500 K of the measurement temperature. In general, the calculations indicate that a judicious choice of a calibration condition will guarantee a measured NO concentration within a factor of two of the actual NO concentration.

Reisel, John R.↗
NASA NTRS1992

Estimation of the viscosities of silicate liquids at high pressure from measurements of oxygen diffusivity

The dynamics and evolution of a magma ocean depend significantly on the structure and physical properties of silicate liquids at high pressure. Viscosity is particularly important because of its effect on the dynamics of convection and crystal setting. Traditionally, the viscosities of silicate liquids have been measured at high pressure by falling sphere viscometry but, due to some limitations of this technique, few measurements have been made at pressures exceeding 2.5 GPa. An alternative approach, which has previously been proven up to 2 GPa, is to use high pressure measurements of oxygen self-diffusivity (D) to estimate viscosity (eta) from the Eyring relationship eta = kT/D lambda (where k is the Boltzmann constant, T is absolute temperature, and lambda is the diffusive jump distance). We have performed preliminary experiments on Na2Si4O9 liquid in order to explore the feasibility of this method up to pressures in excess of 10 GPa. Diffusion couples were prepared from glass starting materials with one half of the sample enriched in O-18 and the other half containing the natural abundance (0.2 wt percent). Diffusion experiments were performed at 1600 to 1800 C at pressures in the range of 2.5 to 10 GPa for times up to 6 minutes using a 1200 ton multianvil apparatus. Oxygen diffusivities were derived from the resulting O-18 concentration profiles, which were analyzed using an ion microprobe. At 1800 C, oxygen diffusivities increase continuously from 1 x 10(exp -10) m(exp -2) s(exp -1) at 2.5 Gpa to 5 x 10(exp -10) m(exp -2) s(exp -1) at 10 GPa. From the Eyring relationship, the viscosity of Na2SiO9 liquid is predicted to decrease by approx. 0.7 log units over this pressure range at 1800 C. These trends, which can be related to changes in the structure of the liquid at high pressure, are in agreement with results of molecular dynamics calculations. These results suggest that it should be possible to estimate the viscosities of silicate liquids up to at least 15 GPa and 2200 C by this method.

Rubie, D. C.↗
NASA NTRS1967

Remotely operated high pressure valve protects test personnel

High pressure valve used in testing certain spacecraft systems is safely opened and closed by a remotely stationed operator. The valve is self-regulating in that if the incoming pressure drops below a desired value the valve will automatically close, warning the operator that the testing pressure has dropped to an undesired level.

Howland, B. T.↗
NASA NTRS1969

High-pressure seals for rotary shafts

High pressure seals for rotating shafts are machined from a polyimide resin. It is more durable and cheaper than the older seals of plastic coated metal and works at temperatures between - 400 degrees and plus 900 degrees f.

Holden, C. P.↗
NASA NTRS1973

High pressure space suit glove

The High Pressure Space Suit Glove Program yielded one prototype glove assembly with an operating pressure of 8.0 psi. The following developments are reported: (1) A new layup technique for incorporation of the mini-convolute systems; (2) modification in the mini-convolute construction to assure cycle life at 8.0 psi in excess of 100,000 cycles; (3) the development of a unique non-orthogonal low torque wrist joint; (4) the development of a low torque single axis joint for use in the thumb and finger first metacarpal joints; and (5) a number of approaches to 1st metacarpal joints were fabricated and tested to establish the joint technqiues.

Elkins, W.↗
NASA NTRS1977

Small, high-pressure liquid hydrogen turbopump

A high pressure, liquid hydrogen turbopump was designed, fabricated, and tested to a maximum speed of 9739 rad/s and a maximum pump discharge pressure of 2861 N/sq. cm. The approaches used in the analysis and design of the turbopump are described, and fabrication methods are discussed. Data obtained from gas generator tests, turbine performance calibration, and turbopump testing are presented.

Csomor, A.↗
NASA NTRS1977

Improved high pressure turbine shroud

A new high pressure turbine shroud material has been developed from the consolidation of prealloyed powders of Ni, Cr, Al and Y. The new material, a filler for cast turbine shroud body segments, is called Genaseal. The development followed the identification of oxidation resistance as the primary cause of prior shroud deterioration, since conversion to oxides reduces erosion resistance and increases spalling under thermal cycled engine conditions. The NICrAlY composition was selected in preference to NIAL and FeCRALY alloys, and was formulated to a prescribed density range that offers suitable erosion resistance, thermal conductivity and elastic modulus for improved behavior as a shroud.

Bessen, I. I.↗
NASA NTRS1980

Small, high pressure liquid hydrogen turbopump

A high pressure, low capacity, liquid hydrogen turbopump was designed, fabricated, and tested. The design configuration of the turbopump is summarized and the results of the analytical and test efforts are presented. Approaches used to pin point the cause of poor suction performance with the original design are described and performance data are included with an axial inlet design which results in excellent suction capability.

Csomor, A.↗
DOE OSTI2023

Vertical high-pressure rinse machine

A high-pressured rinsing system comprises a base including a liquid reservoir, a rotation motor housing including a rotation motor adapted to rotate a spray wand attached, and extending vertically upward from, the rotation motor housing and base, a linear rail support frame attached the base and including a vertical motor and associated linear rail attached thereto, a cavity mounting plate attached to the linear rail, wherein vertical movement of the linear rail causes vertical movement of the cavity mounting plate over the base; and at least one door and a plurality of side panels mounting to an enclosure support frame, wherein the enclosure support frame is mounted and secured to the linear rail support frame and base to create an enclosure around the spray wand and linear rail.

Ring, Timothy J.↗
NASA NTRS1999

Cryogenic High Pressure Sensor Module

A pressure sensor is provided for cryogenic, high pressure applications. A highly doped silicon piezoresistive pressure sensor is bonded to a silicon substrate in an absolute pressure sensing configuration. The absolute pressure sensor is bonded to an aluminum nitride substrate. Aluminum nitride has appropriate coefficient of thermal expansion for use with highly doped silicon at cryogenic temperatures. A group of sensors, either two sensors on two substrates or four sensors on a single substrate are packaged in a pressure vessel.

Chapman, John J.↗
NASA NTRS2001

Cryogenic, Absolute, High Pressure Sensor

A pressure sensor is provided for cryogenic, high pressure applications. A highly doped silicon piezoresistive pressure sensor is bonded to a silicon substrate in an absolute pressure sensing configuration. The absolute pressure sensor is bonded to an aluminum nitride substrate. Aluminum nitride has appropriate coefficient of thermal expansion for use with highly doped silicon at cryogenic temperatures. A group of sensors, either two sensors on two substrates or four sensors on a single substrate are packaged in a pressure vessel.

John J Chapman↗
DOE OSTI2022

High Temperature, High Pressure Stability of Aqueous Foams for Potential Application in Enhanced Geothermal System (EGS)

Enhanced Geothermal Systems (EGS) are typically constructed by injecting high-pressure water into deep hot dry rocks (HDR) under carefully controlled conditions to create new or re-open existing fractures, which usually uses an immense quantity of water. In lieu, a more sustainable technique is to utilize aqueous foams as fracturing fluid to reduce water consumption and waste-water treatments of conventional hydraulic fracturing. Although foam-based fracturing has shown promising results in oil and gas industries, its feasibility is not demonstrated in EGS conditions that usually involve high temperature and high pressures. One potential barrier of utilizing foams in EGS applications is that foams are thermodynamically unstable and will become more unstable with increasing temperature due to liquid drainage, bubble coarsening, and coalescence. This work focuses on evaluation of the stability of selected aqueous foams under high-temperature and high-pressure conditions. Specifically, foams generated with surfactant alfa olefin sulfonate (AOS) were studied at temperature up to 200oC, while the pressure ranged between 100 psi and 1000 psi. The effect of additional stabilizing agents was also examined, including guar gum, bentonite clay, borate salt crosslinker, silicon dioxide nanoparticles (SiO2), and graphene oxide (GO) dispersion. Results showed that the stabilizing agents can enhance the foam thermal stability. Foams made with AOS and the borate salt crosslinker exhibited the longest half-life of 20 min at 200°C when the pressure was at 1000 psi. Data fitting showed that foam stability decreased exponentially as temperature increased. On the other hand, pressure increased the foam half-life which followed a power model. This study indicates that it may be possible to obtain highly stable foams at high-temperature and high-pressure conditions with appropriate stabilizing agents.

Thakore, Viren↗
NASA NTRS1997

Quantitative PLIF Imaging in High-Pressure Combustion

This is the final report for a research project aimed at developing planar laser-induced fluorescence (PLIF) techniques for quantitative 2-D species imaging in fuel-lean, high-pressure combustion gases, relevant to modem aircraft gas turbine combustors. The program involved both theory and experiment. The theoretical activity led to spectroscopic models that allow calculation of the laser-induced fluorescence produced in OH, NO and 02 for arbitrary excitation wavelength, pressure, temperature, gas mixture and laser linewidth. These spectroscopic models incorporate new information on line- broadening, energy transfer and electronic quench rates. Extensive calculations have been made with these models in order to identify optimum excitation strategies, particularly for detecting low levels (ppm) of NO in the presence of large 02 mole fractions (10% is typical for the fuel-lean combustion of interest). A promising new measurement concept has emerged from these calculations, namely that excitation at specific wavelengths, together with detection of fluorescence in multiple spectral bands, promises to enable simultaneous detection of both NO (at ppm levels) and 02 or possibly NO, 02 and temperature. Calculations have been made to evaluate the expected performance of such a diagnostic for a variety of conditions and choices of excitation and detection wavelengths. The experimental effort began with assembly of a new high-pressure combustor to provide controlled high-temperature and high-pressure combustion products. The non-premixed burner enables access to postflame gases at high temperatures (to 2000 K) and high pressures (to 13 atm), and a range of fuel-air equivalence ratios. The chamber also allowed use of a sampling probe, for chemiluminescent detection of NO/NO2, and thermocouples for measurement of gas temperature. Experiments were conducted to confirm the spectroscopic models for OH, NO and 02.

Hanson, R. K.↗
NASA NTRS1978

High pressure phase transitions in tetrahedrally coordinated semiconducting compounds

New experimental results are reported for structural transitions at high pressure in several III-V compounds and two II-VI compounds. These data, together with earlier results, are then compared with the predictions of model calculations of Van Vechten. Experimental transition pressures are often at variance with calculated values. However, his calculation assumes that the high pressure phase is metallic, with the beta-Sn structure. The present results show that several compounds assume an ionic NaCl structure at high pressure, while others have neither the beta-Sn nor NaCl structure.

Yu, S. C.↗
NASA NTRS1975

Underground storage systems for high-pressure air and gases

This paper is a discussion of the safety and cost of underground high-pressure air and gas storage systems based on recent experience with a high-pressure air system installed at Moffett Field, California. The system described used threaded and coupled oil well casings installed vertically to a depth of 1200 ft. Maximum pressure was 3000 psi and capacity was 500,000 lb of air. A failure mode analysis is presented, and it is shown that underground storage offers advantages in avoiding catastrophic consequences from pressure vessel failure. Certain problems such as corrosion, fatigue, and electrolysis are discussed in terms of the economic life of such vessels. A cost analysis shows that where favorable drilling conditions exist, the cost of underground high-pressure storage is approximately one-quarter that of equivalent aboveground storage.

Beam, B. H.↗
NASA NTRS2007

Manufacturing Diamond Under Very High Pressure

A process for manufacturing bulk diamond has been made practical by the invention of the High Pressure and Temperature Apparatus capable of applying the combination of very high temperature and high pressure needed to melt carbon in a sufficiently large volume. The apparatus includes a reaction cell wherein a controlled static pressure as high as 20 GPa and a controlled temperature as high as 5,000 C can be maintained.

Voronov, Oleg↗
DOE OSTI2020

Neutron diffraction study of magnetic ordering in high pressure phases of rare earth metal holmium

The magnetic ordering in rare earth metals is well established for ambient pressure crystal structures, however, little is known about the magnetic ordering in their corresponding high-pressure crystalline modifications. Holmium (Ho) was studied in a large-volume diamond anvil cell at the Spallation Neutron Source to high-pressure up to 20 GPa and to low-temperature to 10 K. We have conducted two independent high-pressure low-temperature experiments under non-hydrostatic and quasi-hydrostatic pressure conditions respectively. The ambient pressure hexagonal close packed (hcp) phase of holmium shows two magnetic transitions below 10 GPa one to an incommensurate Antiferromagnetic (AFM) phase and another to a conical-Ferromagnetic (c-FM) phase. In contrast, alpha-Samarium-type (α-Sm) phase above 10 GPa and the double hexagonal close packed (dhcp) phase above 19 GPa show only one FM transition marked by the appearance of a magnetic peak at 3 Å and the concurrent enhancement of nuclear peaks below 30 K. Finally, these new transitions observed by neutron diffraction can be accounted by a commensurate superlattice formation along c-axis in both the α-Sm-type phase and the dhcp phase.

36 MATERIALS SCIENCE↗