Search NASA⌕ Search

SEARCH · Search NASA

Results for “Image Transmission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Role of structural defects in mediating disordering processes at irradiated epitaxial Fe 3 O 4 / Cr 2 O 3 interfaces

Disordering processes in oxide materials are complicated by the presence of interfaces, which can serve as either point defect sinks or accumulation sites; the response depends on factors such as interfacial structure, chemistry, and termination. Here, we have characterized the disordering of epitaxial Fe 3 O 4 (111) / Cr 2 O 3 (0001) thin film heterostructures after 400 keV Ar 2+ radiation at room temperature. The density of misfit dislocations in both the Fe 3 O 4 overlayer and Cr 2 O 3 buffer layer is varied by changing the thickness of Cr 2 O 3 to be pseudomorphically strained to the Al 2 O 3 (0001) substrate (5 nm thick) or partially relaxed (20 nm thick), as confirmed by Bragg filtering analysis of scanning transmission electron microscopy images. In both cases, irradiation leads to damage accumulation on the Fe 3 O 4 side of the heterointerface, as shown by Rutherford backscattering spectrometry measurements in the channeling geometry. However, the interface with more misfit dislocations exhibits disordering at a faster rate than the less-defective interface. Likewise, layer-resolved electron energy loss spectroscopy reveals interfacial reduction of Fe after irradiation at the more defective interface. Intermixing of Cr across the interface is observed by atom probe tomography, which is likely facilitated by the generation of Cr interstitials in Cr 2 O 3 under irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Coexistence of antiferrodistortive and polar order in a superconducting SrTi⁢O 3 film

Strontium titanate (SrTiO 3 ) can exhibit multiple orders, including superconductivity, an antiferrodistortive instability and ferroelectricity. The cooperation or competition between these orders in samples that undergo all three transitions is of great fundamental interest. Here we report scanning transmission electron microscopy imaging of the antiferrodistortive and ferroelectric structural distortions in a compressively strained SrTiO 3 film that was previously shown to become superconducting at ~ 410 mK. The experiments are complemented by first-principles simulations. Unlike the polar ferroelectric phase, which is suppressed by dopants, the antiferrodistortive order is insensitive to the presence of the free carriers. The single domain nature of the antiferrodistortive phase excludes any role of antiferrodistortive domain walls in the superconductivity. Furthermore, a previously reported low temperature resistance anomaly is associated with the ferroelectric transition, not the antiferrodistortive transition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Buffer-layer effect on the ferromagnetism of manganite heterojunctions

Identifying and understanding interfacial magnetic structures of transition-metal oxides are of great importance not only for fundamental physics but also for potential device applications. Among them, manganite and ruthenate heterostructures have attracted considerable interest due to their intriguing interfacial properties induced by complex magnetic interactions. Here, we report the observation of dramatic buffer-layer dependence of ferromagnetism in ultrathin (L⁢a 2/3 ⁢C⁢a 1/3 )⁢Mn⁢O 3 (LCMO)-based heterostructures. Though all trilayers are nonmetallic, the SrRu⁢O 3 -buffered LCMO trilayer exhibits enhanced ferromagnetism with the Curie temperature (𝑇 C ∼ 198K) much higher than for CaRu⁢O 3 (𝑇 C ∼ 99K)- and SrTi⁢O 3 (𝑇 C ∼ 42K)-buffered counterparts, as well as the monolithic LCMO films with similar thickness. Combining atomically resolved scanning transmission electron microscopy imaging with electron energy loss spectroscopy mapping, we reveal that asymmetric interfaces exist in the SrRu⁢O 3 buffered trilayer, with one exhibiting 1 unit-cell Sr diffusion into LCMO, which is responsible for the 𝑇 C enhancement. In contrast, charge transfer, which has been proposed previously as a possible mechanism, is excluded in this study. In conclusion, our results may pave a promising road toward effective atomic control of interfacial magnetism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Ion transport and ultra-efficient osmotic power generation in boron nitride nanotube porins

Nanotube porins form transmembrane nanomaterial-derived scaffolds that mimic the geometry and functionality of biological membrane channels. We report synthesis, transport properties, and osmotic energy harvesting performance of another member of the nanotube porin family: boron nitride nanotube porins (BNNTPs). Cryo–transmission electron microscopy imaging, liposome transport assays, and DNA translocation experiments show that BNNTPs reconstitute into lipid membranes to form functional channels of ~2-nm diameter. Ion transport studies reveal ion conductance characteristics of individual BNNTPs, which show an unusual C 1/4 scaling with ion concentration and pronounced pH sensitivity. Reversal potential measurements indicate that BNNTPs have strong cation selectivity at neutral pH, attributable to the high negative charge on the channel. BNNTPs also deliver very large power density up to 12 kW/m 2 in the osmotic gradient transport experiments at neutral pH, surpassing that of other BNNT-based devices by two orders of magnitude under similar conditions. Our results suggest that BNNTPs are a promising platform for mass transport and osmotic power generation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AD_LTEM

This software uses AI tools for enhanced functional imaging using Lorentz transmission electron microscopy by retrieving phase shift at higher spatial resolution, and under noisy conditions. This is a companion code for a publication that is currently being submitted (APT # 164160).

PHATAK, CHARUDATTA↗
DOE OSTI2022

TEMWizard pyCHIP.gui

TEMWizard pyCHIP.gui is used to visualize intermediate and final results from Atomap, an open-source software tool for determining the position and other features of atomic columns in transmission electron microscopy images. Also known as pyCHIP.gui.

Spurgeon, Steven R.↗
DOE OSTI2022

pnnl/Temwizard

TEMWizard is used to visualize results from Atomap, an open-source software tool for determining the position and other features of atomic columns in transmission electron microscopy images.

Oostrom, Marjolein↗
DOE OSTI2020

NSUF Rad-AFM: Nanoscale Material Property Measurements of Radioactive Materials

Many advances in our understanding of radiation induced damage mechanisms are due to imaging techniques including transmission electron microscopy and scanning electron microscopy. However, the effect of these radiation induced defects characterized on the atomic to micrometer scale are often interpreted by changes in bulk material properties measured in the hundreds of microns to cm scale. In order to bridge this gap, additional tools need to be developed for use with radioactive materials. To this end a new Asylum Infinity multimodal atomic force microscope (AFM) has been added to the library of Nuclear Science User Facility (NSUF) instruments for use on radioactive materials. This instrument is housed in the Radiochemical Processing Laboratory (RPL) which is a Department of Energy Hazard Category II Non-Reactor Nuclear Facility operated by Battelle at Pacific Northwest National Laboratory. This allows for the handling, sample preparation, and characterization of highly radioactive materials providing a unique capability to understand fundamental properties of nuclear materials and the effects of radiation induced damage.

Riechers, Shawn L.↗
DOE OSTI2020

MOCVD Growth and Characterization of Wide Bandgap ZnGeN 2 Thin Films

ZnGeN 2 is a wide bandgap material having less than 0.1% lattice mismatch with GaN and bandgap within few percent of that of GaN. Based on the first principle calculations, the valence band of ZnGeN 2 is situated ~1.4 eV above that of GaN at the heterointerface. Such a staggered band alignment between two closely lattice matched materials has already been demonstrated promising for novel optoelectronic device designs, for example, high efficiency blue and green light emitting diodes. However, the research on ZnGeN 2 is yet to pass the inceptive period. We report on the growth of single crystalline ZnGeN 2 films using metalorganic chemical vapor deposition and investigation on the crystalline, optical, electrical properties. Diethylzinc (DEZn), germane (GeH 4 ) and ammonia were used as the precursors for Zn, Ge and N, respectively. Films were grown on GaN and sapphire substrates. The Zn/Ge atomic ratio in the films determined from energy dispersive X-ray spectroscopy was found to decrease with increase in growth temperature but to increase with increase in pressure and DEZn/GeH 4 molar flow rate ratio. The X-ray diffraction (XRD) 2θ-ω spectra of the single crystalline ZnGeN 2 films resembled those of orthorhombic (perfectly ordered cations) or distorted wurtzite (disordered cations) polymorphs. High resolution scanning transmission electron microscopy imaging was used to further investigate the crystalline quality and crystalline structure of the films. The single crystalline films on c-sapphire or GaN substrates were found to have planar surface from scanning electron micrographs while those on r-sapphire substrate had stepped surface. No near band edge peak but a broad peak at ~2.05 eV was observed in the photoluminescence (PL) spectra, which was attributed to the transitions involving deep level defects. The PL excitation spectra peaked around 3.4 eV, which is due to the enhanced absorption of photons having energy close to the band gap. The as grown films were found to be n-type with 10 18 – 10 19 cm -3 carrier densities and mobility up to 17 cm 2 /V·s. In the end, the advancement made in this work regarding the growth of ZnGeN 2 thin films is a footstep towards the understanding of the material itself and in turn, towards the implementation of ZnGeN 2 based novel device designs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Hardness Measurements and Interface Behavior of SiC-B 4 C-Si Multiple Phase Particulate Composites Made with Melt Infiltration and Additive Manufacturing

Reaction-bonded SiC-B 4 C-Si ceramic composites were binder jet 3D-printed and subsequently pressureless-melt-infiltrated with molten Si. The addition of B 4 C aided the Si infiltration to produce a highly dense composite. The microstructures and phases of these composites were examined. The measured hardness values of each constituent with Vickers and nanoindentation matched the bulk values, and the macro-hardness values with Knoop and spherical indentation represented the bulk, composite hardness values of all three phases together, which was close to a rule of mixtures value. For particulate-based composites, this is a significant finding. The interfacial bonds of SiC and Si were imaged using scanning transmission electron microscopy to view intimacy, whereas the crack propagation was examined with carefully placed indents. This work demonstrated that pressureless melt infiltration with a reactive particle provides a method to shape non-wetting reaction-bonded ceramic composites with limited shrinkage and high density and provides insights into the mechanical behavior with numerous indentation techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In Situ Ultra-Small- and Small-Angle X-ray Scattering Study of ZnO Nanoparticle Formation and Growth through Chemical Bath Deposition in the Presence of Polyvinylpyrrolidone

ZnO inverse opals combine the outstanding properties of the semiconductor ZnO with the high surface area of the open-porous framework, making them valuable photonic and catalysis support materials. One route to produce inverse opals is to mineralize the voids of close-packed polymer nanoparticle templates by chemical bath deposition (CBD) using a ZnO precursor solution, followed by template removal. To ensure synthesis control, the formation and growth of ZnO nanoparticles in a precursor solution containing the organic additive polyvinylpyrrolidone (PVP) was investigated by in situ ultra-small- and small-angle X-ray scattering (USAXS/SAXS). Before that, we studied the precursor solution by in-house SAXS at T = 25 °C, revealing the presence of a PVP network with semiflexible chain behavior. Heating the precursor solution to 58 °C or 63 °C initiates the formation of small ZnO nanoparticles that cluster together, as shown by complementary transmission electron microscopy images (TEM) taken after synthesis. The underlying kinetics of this process could be deciphered by quantitatively analyzing the USAXS/SAXS data considering the scattering contributions of particles, clusters, and the PVP network. A nearly quantitative description of both the nucleation and growth period could be achieved using the two-step Finke–Watzky model with slow, continuous nucleation followed by autocatalytic growth.

36 MATERIALS SCIENCE↗
NASA NTRS1968

ATS-D launch scheduled

Experimental design and prelaunch data on ATS-D equipped with image orthicon, microwave transmission equipment, and ion engine

Source record↗
NASA NTRS1972

Study of optimum methods of optical communication

Optimum methods of optical communication accounting for the effects of the turbulent atmosphere and quantum mechanics, both by the semi-classical method and the full-fledged quantum theoretical model are described. A concerted effort to apply the techniques of communication theory to the novel problems of optical communication by a careful study of realistic models and their statistical descriptions, the finding of appropriate optimum structures and the calculation of their performance and, insofar as possible, comparing them to conventional and other suboptimal systems are discussed. In this unified way the bounds on performance and the structure of optimum communication systems for transmission of information, imaging, tracking, and estimation can be determined for optical channels.

Harger, R. O.↗
NASA NTRS1979

Voyager telecommunications - The broadcast from Jupiter

The means by which the data collected by the Voyager 1 mission to Jupiter were returned to earth are presented. Radio links between the earth and the spacecraft are used for the transmission of both imaging and nonimaging telemetry from the spacecraft and commands from the earth and for radiometric observations of the spacecraft and its environment. Features which have lead to vast improvements in the capability of the Voyager telecommunications system over that of previous space probes include the use of X-band rather than S-band telemetry, a dual power X-band traveling wave tube amplifier, a 3.7 m spacecraft antenna and a single channel telemetry system with concatenated coding. Communications equipment at the three ground complexes of the Deep Space Network for telemetry reception includes 64 m steerable antennas, cryogenic maser preamplifiers and a phase-lock loop receiver. Voyager 1 has met or exceeded all of its telecommunications requirements, providing a 98% data return and a total of 2 x 10 to the 11th data bits during the Jupiter encounter.

Edelson, R. E.↗
NASA NTRS1979

New phyllosilicate types in a carbonaceous chondrite matrix

Observations of new types of layer silicates in the crystalline regions of the matrix of a carbonaceous chondrite are reported. Ion-thinned sections of the Murchison meteorite were observed by high-resolution transmission electron microscopy. Images obtained of patterns of fringe spacings of 4.9 and 7.3 A are interpreted as resulting from ordered and disordered sequences of brucite-like and serpentine-like layers, respectively. The temperature and pressure conditions of phyllosilicate formation in the Murchison matrix are discussed in light of the suggested crysotile serpentine and brucite layers and evidence of Fe and Al in the layered intergrowths.

Mackinnon, I. D. R.↗
NASA NTRS1981

Synthetic aperture radar and digital processing: An introduction

A tutorial on synthetic aperture radar (SAR) is presented with emphasis on digital data collection and processing. Background information on waveform frequency and phase notation, mixing, Q conversion, sampling and cross correlation operations is included for clarity. The fate of a SAR signal from transmission to processed image is traced in detail, using the model of a single bright point target against a dark background. Some of the principal problems connected with SAR processing are also discussed.

Dicenzo, A.↗
NASA NTRS1988

Superconductivity in the high-Tc Bi-Ca-Sr-Cu-O system - Phase identification

Four phases are observed in superconducting Bi-Ca-Sr-Cu-O samples. The superconducting phase, with onset temperature near 120 K, is a 15.4-A-layered compound with composition near Bi2Ca1Sr2Cu2O9 and an A-centered orthorhombic unit subcell 5.41 x 5.44 x 30.78 A. X-ray diffraction and electron microscopy data are consistent with a structure of alternating perovskite and Bi2O2 layers. High-resolution transmission electron microscopy images reveal a b-axis superstructure of 27.2 A, numerous (001) stacking faults, and other defects.

Hazen, R. M.↗
NASA NTRS1989

A helmet mounted display demonstration unit for a Space Station application

Under NASA guidance an advanced development helmet mounted display (HMD) has been designed and fabricated. Delivery has been made of an extravehicular mobility unit (EMU) HMD demonstration unit as an alternative to the current low-resolution, chest-mounted display, and cuff-mounted checklists. Important design goals achieved with this HMD include the use of transmissive liquid display image sources with fairly high resolution (text, graphics, and video compatible), binocular viewing with total image overlap, virtual image projection, low profile packaging, low power design, and demonstration of voice control of the HMD data. Test results showed that the HMD program successfully demonstrated the feasibility of the concept and operated as designed, meeting the necessary program requirements.

Gernux, Carolyn G.↗