Search NASA⌕ Search

SEARCH · Search NASA

Results for “Instabilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Time-resolved particle image velocimetry measurements of the turbulent Richtmyer–Meshkov instability

Experiments are presented on the Richtmyer–Meshkov instability (RMI) with a three-dimensional, multi-mode initial perturbation. The experiments use a vertical shock tube, where a stably stratified interface is formed between air and sulphur hexafluoride (SF 6 ) via counterflow. A perturbation is imposed at the interface by vertical oscillation of the gas column, forming Faraday waves. The interface is accelerated by a Mach 1.17 (in air) shock wave, and the development of the mixing region between the gases is investigated using particle image velocimetry. Following shock acceleration, a reflected shock wave from the bottom of the shock tube interacts with the mixing layer a second time (reshock). The experiment is initialized with both high and low amplitude perturbations to examine the effect of the perturbation amplitude on measured quantities. The instability growth exponent (θ) is determined from the kinetic energy field using the width of the mixing layer and the decay of kinetic energy, which are found to be in agreement when the flow is most strongly excited. A growth exponent of θ ≈ 0.5 is found for all cases except the high-amplitude reshocked regime (where θ ≈ 0.33). High-amplitude experiments exhibit the transitional outer Reynolds number (Re ≡ hh˙/ν >10 4 ) required for mixing transition following the incident shock, and both experiments are elevated well above this threshold following reshock. However, neither set of experiments meet the more stringent requirements proposed by Zhou et al. (Phys. Rev.E, vol. 67, issue 5, 2003) which include the time dependent aspect of the RMI, an observation which is also made when examining the spectra.

42 ENGINEERING↗
DOE OSTI2026

Preheat effects in laser-driven Rayleigh–Taylor instability experiments at intensities greater than $10^{15}$ $\textrm{W}$ $\textrm{cm}^{-2}$ at OMEGA EP and the NIF

The propagation of high-energy X-rays or hot electrons have the potential to alter the initial conditions in experimental target designs, especially at material interfaces, for laser-driven inertial confinement fusion (ICF) and high-energy density (HED) experimental platforms. Hot-electron preheat can drastically modify the initial conditions of experimental targets used to study the deceleration-stage Rayleigh–Taylor instability (RTI) both with and without applied magnetic fields. Therefore, it is necessary to understand and quantify the impact of hot-electron preheat. The hydrodynamic (HD) capabilities in the Ares code are used to study the effects varying levels of preheat can have on RTI evolution. The experimental and computational studies presented in this work demonstrate that at high laser intensities of around or greater than 10 15 W cm −2 , there is hot-electron generation from laser plasma instabilities which induces substantial preheat and impacts the morphology of RTI evolution and even inhibits the intended RTI growth such that it is not observable experimentally. The necessity of better quantifying hot-electron induced preheat and mitigating its impact on such high-intensity direct-drive laser experiments in the future is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Numerical Mixing Suppresses Submesoscale Baroclinic Instabilities Over Sloping Bathymetry

Abstract The impacts of spurious numerical salinity mixing on the larger‐scale flow and tracer fields are characterized using idealized simulations. The idealized model is motivated by realistic simulations of the Texas‐Louisiana shelf and features oscillatory near‐inertial wind forcing. can exceed the physical mixing from the turbulence closure in frontal zones and within the mixed layer. This suggests that simulated mixing processes in frontal zones are driven largely by . Near‐inertial alongshore wind stress amplitude is varied to identify a base case that maximizes the ratio of to in simulations with no prescribed horizontal mixing. We then test the sensitivity of the base case with three tracer advection schemes (MPDATA, U3HC4, and HSIMT) and conduct ensemble runs with perturbed bathymetry. Instability growth is evaluated using the volume‐integrated eddy kinetic energy and available potential energy . While all schemes have similar total mixing, the HSIMT simulations have over double the volume‐integrated and 20% less relative to other schemes, which suppresses the release of and reduces the by roughly 25%. This results in reduced isohaline variability and steeper isopycnals, evidence that enhanced suppresses instability growth. Differences in and between the MPDATA and U3HC4 simulations are marginal. However, the U3HC4 simulations have 25% more . Experiments with variable horizontal viscosity and diffusivity coefficients show that small amounts of prescribed horizontal mixing improve the representation of the ocean state for all advection schemes by reducing the and increasing the .

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Relativistic Coulomb screening in pulsational pair instability supernovae

Pulsational pair-instability supernovae (PPISNe) and pair instability supernovae (PISNe) are the result of a thermonuclear runaway in the presence of a background electron-positron pair plasma. As such, their evolution and resultant black hole masses could possibly be affected by screening corrections due to the electron pair plasma. The sensitivity of PISNe and PPISNe to relativistic weak screening has been explored. In this paper a weak screening model that includes effects from relativistic pair production has been developed and applied at temperatures approaching and exceeding the threshold for pair production. This screening model replaces “classical” screening commonly used in astrophysics. Modifications to the weak screening electron Debye length were incorporated in a computationally tractable analytic form. In PPISNe the BH masses were found to increase somewhat at high temperatures, though this increase is small. The BH collapse is also found to occur at earlier times, and the pulsational morphology also changes. In addition to the resultant BH mass, the sensitivity to the screening model of the pulsational period, the pulse structure, the PPISN-to-PISN transition, and the shift in the BH mass gap has been analyzed. The dependence of the composition of the ejected mass was also examined.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Nonlinear kinetic simulation study of the ion–ion streaming instability in single- and multi-ion species plasmas

The nonlinear evolution of the ion–ion streaming instability (IISI) is studied using numerical techniques novel to this problem that afford direct insight into the evolution of the particle distributions of each species. Here, during the linear phase of the instability, we demonstrate quantitative agreement with linear kinetic theory. Subsequently, the electrostatic field generated by the IISI causes ring-like velocity distributions of ions to form that are both heated and slowed to varying degrees relative to their initial flows. Due to variation in the trapping conditions for ion species of differing charge-to-mass ratio, when flows of multiple species interact, the nonlinear evolution of each species can be starkly different: we show a case where a lighter ion species is completely stopped by a heavier ion species via the IISI alone (i.e., without collisions) and, for the first time, demonstrate how the IISI can introduce a relative flow between ion species that initially have the same flow velocities, thereby separating them.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Drift waves enstrophy, zonal flow, and nonlinear evolution of the modulational instability

The interaction of the drift wave (DW) turbulence and zonal flow (ZF) is investigated with the modified Hasegawa–Mima equation taking into account the backreaction of ZF velocity on DW turbulence. It is shown that the y-averaged enstrophy of DW turbulence and the velocity of ZF are intrinsically related. By utilizing this feature, a nonlinear stage of DW modulational instability is considered within the framework of the wave kinetic equation. It is shown that in this approximation, the nonlinear stage of the modulational instability results in the collapsing solutions, accompanied by the “wave breaking” phenomenon. Numerical simulations based on the Hasegawa–Mima equation show that for a weak DW turbulence, Φ ̃ = ( e φ ̃ / T e ) ( L n / ρ s ) ⪝ 1 , the collapsing-like features on both ZF and y-averaged enstrophy of DW turbulence decay in time and then re-emerge again at different locations. For the case of a strong DW turbulence, Φ ̃ > 1 , where nonlinear interactions of DW harmonics dominate, stable spatial structures of ZF and y-averaged enstrophy of DW turbulence emerge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Analytic quasi-steady evolution of marginally unstable kinetic plasma instabilities in the presence of drag and scattering

The 1D bump-on-tail problem is studied in order to determine the influence of drag on quasi-steady solutions near marginal stability (1-γ d /γ L << 1) when effective collisions are much larger than the instability growth rate (ν>>γ). In this common tokamak regime, it is rigorously shown that the paradigmatic Berk–Breizman cubic equation for the nonlinear mode evolution reduces to a much simpler differential equation, dubbed the time-local cubic equation, which can be solved directly. It is found that in addition to increasing the saturation amplitude, drag introduces a shift in the apparent oscillation frequency by modulating the saturated wave envelope. Furthermore, excellent agreement is found between the analytic solution for the mode evolution and both the numerically integrated Berk–Breizman cubic equation and fully nonlinear 1D Vlasov simulations. Experimentally isolating the contribution of drag to the saturated mode amplitude for verification purposes is explored but complicated by the reality that the amount of drag cannot be varied independently of other key parameters in realistic scenarios. While the influence of drag is modest when the ratio of effective drag to effective scattering α/ν is very small, it can become substantial when α/ν ≳ 0.5, suggesting that drag should be accounted for in quantitative models of fast-ion-driven instabilities in fusion plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Design of a high energy density experiment to measure the suppression of hydrodynamic instability in an applied magnetic field

A transverse magnetic field can suppress the hydrodynamic instability growth of an unstable plasma interface. This effect, of interest to inertial confinement fusion and astrophysics, has mostly been studied via simulation. Here, we present the design of an experiment at the National Ignition Facility (NIF) to demonstrate this effect in a laboratory. Simulations indicate that the timescale for the diffusion of the magnetic field across the mixing region should be at least comparable to the timescale of the instability growth in order to have a measurable suppression effect. This motivates the use of lower density target materials than usual high energy density (HED) hydrodynamics experiments to permit faster hydrodynamics and higher plasma conductivities (through higher temperature), for a given laser drive and magnetic field. We discuss a target design for creating a Rayleigh–Taylor unstable HED plasma interface that uses 320 mg/cc iodine-doped carbon foam as the heavy material, 20 mg/cc carbon foam as the light material, and a 6 lm amplitude, a 120 lm wavelength ripple machined at the interface, which shows a measurable suppression effect with a nominal NIF drive and a 30 T magnetic field (the present facility limit). Here, models indicate lower density foams that may display even larger suppression effects, as the Hohlraum drive also radiatively preheats the foam to permit even higher temperatures and, hence, higher conductivities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

High spatial resolution and contrast radiography of hydrodynamic instabilities at the National Ignition Facility

In this work, we are developing techniques for studying the Rayleigh–Taylor (RT) and Richtmyer–Meshkov (RM) instabilities in a planar geometry at high-energy-densities at the National Ignition Facility (NIF). In particular, through the improvement of experimental imaging quality, we are progressing toward the study of the turbulent regime of the mixing regions in capsule implosion experiments for inertial confinement fusion, which requires few micrometers resolution. Using 60 NIF beams, a solid shock tube is driven launching a shock wave that crosses the interface between a dense and a light material pre-machined in the target to obtain sinusoidal ripples, which results in RM and RT instabilities that are imaged using the NIF Crystal Backlighter Imager. High-quality images were obtained with a mean resolution of 7 μm and improved contrast. While the obtained resolution does not allow the observation of the smallest scale of the “turbulent” energy spectrum, the generated image encompasses 63% of the total flow energy, a 50% improvement over previous studies, which is observed for the first time a roll-up feature in a high energy density-type RT experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Mitigation of hot-electron preheat from the two-plasmon-decay instability using silicon-doped plastic shells in direct-drive implosions on OMEGA

Hot electrons generated by the two-plasmon-decay (TPD) instability in laser-direct-drive implosions preheat the fuel and degrade performance. The mitigation of preheat using silicon-doped ablators (i.e., preheat is reduced by a factor of 1.40 ± 0.04) while decreasing the ratio of the laser spot diameter to the target diameter (⁠R b /R t⁠ ) to mitigate cross-beam energy transfer has been demonstrated on the OMEGA laser for quarter-critical laser intensities of 4.1 x 10 14 W/cm 2 ⁠, equivalent to an incident laser intensity of 8.3 x 10 14 W/cm 2 ⁠. The silicon dopant increases the electron temperature of the ablation plasma, which raises the intensity threshold for the onset of the TPD instability. These results show that implosion designs utilizing higher drive intensities can be used to achieve higher shell velocities, which are currently inaccessible with plastic ablators due to excessive preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A two-dimensional numerical study of the magneto-Rayleigh–Taylor instability with FLASH: Application to the staged Z-pinch concept

Magnetically driven implosions involving a liner collapsing onto a target are inherently vulnerable to the magneto-Rayleigh–Taylor instability (MRTI). Among the various approaches proposed to achieve fusion conditions within the target, the staged Z-pinch (SZP) concept employs a high-Z liner, the advantages of which remain an active area of investigation. Consequently, ongoing design optimization efforts are essential, while critical physical processes such as magnetic field (B-field) diffusion and radiation transport increase the complexity of required simulations. In this study, we utilize the new capabilities of the FLASH code to simulate in 2D, for the first time using this code, staged Z-pinch configurations (designated SZP1 and SZP1*), focusing on their stability. First, a comparison of simulation results with theoretical predictions of MRTI growth provide new insights into the often-overlooked influences of high mesh resolution and initial perturbation seeding on instability dynamics. These findings then lead to a discussion on potential improvements for future SZP experiments. These include the use of an axial B-field stabilization and the optimization of radiation transport processes during the implosion. The results presented herein establish the framework for simulating multi-dimensional Z pinches using the FLASH code and pave the way for the development of innovative experimental configurations leveraging its advanced simulation capabilities.

Adaptive mesh refinement↗
DOE OSTI2025

Rotation of electrothermal-instability-driven overheating structure due to helically oriented surface magnetic field on a high-current-density aluminum rod

Experiments on the 1-MA, 100-ns-rise-time Mykonos Facility demonstrate rotation of electrothermal instability (ETI)-driven overheating structure on 1.00-mm-diameter, 10-nm-surface roughness, 99.999%-pure aluminum rods, which are pulsed with helically polarized surface magnetic field. Rods are machined to include pairs of 10-micron-scale quasi-hemispherical voids or “engineered defects (ED)” which provide the dominant current density perturbation from which ETI grows most rapidly. Experiments include an axial magnetic field component through the addition of a helically wound return-current electrode or “helical return can (HRC).” For a given HRC design, azimuthal field (B ɵ ) and axial field (B z ) components rise at a prescribed and fixed ratio, driving an increasing magnetic field of constant polarization at the rod's surface; most experiments generated surface magnetic field at a 15-degree field polarization angle (from horizontal) defined as ɸ B = arctan(B z /B ɵ ). ETI-driven emission patterns from individual ED are observed to rotate along ɸ B , while emission patterns from dielectric-coated ED pairs are shown to elongate and preferentially merge along ɸ B , in qualitative agreement with 3D-magnetohydrodynamic simulations. These data strongly support that for a randomized distribution of current density perturbations on a high-current density conductor, nearby perturbations will favorably merge about ɸ B , with the degree of merging increasing with current. Such observations offer fundamental new understanding of the seeding mechanisms of the helical magneto-Rayleigh Taylor (MRT) instabilities observed from axially magnetized magnetically driven imploding liners.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Elastic-instability–enabled locomotion

Locomotion of an organism interacting with an environment is the consequence of a symmetry-breaking action in space-time. Here we show a minimal instantiation of this principle using a thin circular sheet, actuated symmetrically by a pneumatic source, using pressure to change shape nonlinearly via a spontaneous buckling instability. This leads to a polarized, bilaterally symmetric cone that can walk on land and swim in water. In either mode of locomotion, the emergence of shape asymmetry in the sheet leads to an asymmetric interaction with the environment that generates movement––via anisotropic friction on land, and via directed inertial forces in water. Scaling laws for the speed of the sheet of the actuator as a function of its size, shape, and the frequency of actuation are consistent with our observations. The presence of easily controllable reversible modes of buckling deformation further allows for a change in the direction of locomotion in open arenas and the ability to squeeze through confined environments––both of which we demonstrate using simple experiments. Our simple approach of harnessing elastic instabilities in soft structures to drive locomotion enables the design of novel shape-changing robots and other bioinspired machines at multiple scales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Suppression of pair beam instabilities in a laboratory analogue of blazar pair cascades

The generation of dense electron–positron pair beams in the laboratory can enable direct tests of theoretical models of γ-ray bursts and active galactic nuclei. We have successfully achieved this using ultrarelativistic protons accelerated by the Super Proton Synchrotron at (CERN). In the first application of this experimental platform, the stability of the pair beam is studied as it propagates through a meter-length plasma, analogous to TeV γ-ray-induced pair cascades in the intergalactic medium. It has been argued that pair beam instabilities disrupt the cascade, thus accounting for the observed lack of reprocessed GeV emission from TeV blazars. If true, this would remove the need for a moderate strength intergalactic magnetic field to explain the observations. We find that the pair beam instability is suppressed if the beam is not perfectly collimated or monochromatic, hence the lower limit to the intergalactic magnetic field inferred from γ-ray observations of blazars is robust.

blazar jets↗
DOE OSTI2020

Stabilizing effect of enhanced resistivity on peeling-ballooning instabilities on EAST

Previous stability analysis of NSTX equilibrium with lithium-conditioning demonstrates that enhanced resistivity due to the increased effective charge number Z eff (i.e. increased impurity level) can provide a stabilizing effect on low-n edge localized modes. This paper extends the resistivity stabilizing effect to the intermediate-n peeling-ballooning (PB) instabilities with the linear stability analysis of EAST high-confinement mode equilibria in NIMROD two-fluid calculations. However, in this work, the resistivity stabilizing effect on PB instabilities in the EAST tokamak appears weaker than that found in NSTX. This work may provide better insight into the physical mechanism behind the beneficial effects of impurities on pedestal stability.

EAST tokamak↗
DOE OSTI2020

The physics of spontaneous parity-time symmetry breaking in the Kelvin–Helmholtz instability

Abstract We show that the dynamical system of an inviscid fluid with velocity shear admits parity-time (PT) symmetry, which provides a physical explanation of the well-known observation that the spectrum of the perturbation eigenmodes of the system is symmetric with respect to the real axis. It is found that the Kelvin–Helmholtz instability is triggered when and only when the PT symmetry is spontaneously broken. The analysis of PT symmetry also reveals that the relative phase between parallel velocity and pressure perturbations needs to be locked at π /2 when the instability is suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Fast ion transport by sawtooth instability in the presence of ICRF-NBI synergy in JET plasmas

JET experiments have shown that the three-ion scenarios using waves in the ion cyclotron range of frequencies (ICRF) is an efficient way to build fast ion population through beam ion acceleration by radio frequency (RF) waves. Here, such a heating scheme is applied to plasmas with at least two thermal ion species. Analysis of mixed discharges with complex heating schemes requires a workflow that allows to model thermal and fast ion transport consistently. This paper is dedicated to modelling of a mixed plasma discharge with significant fraction of fast ions and contributes to development of fast ion transport models. For interpretive analysis with the TRANSP code a JET hydrogen-deuterium (HD) plasma discharge with neutral beam injection (NBI) and ICRF heating has been chosen. The task is complicated by NBI-ICRF synergy and plasma magnetohydrodynamic activity, like sawtooth crashes. D beam ions accelerated by RF waves form a high energy tail in fast ion distribution. Significant difference between the neutron rate computed by TRANSP and measured one is observed if the same diffusivity for electrons and ions is assumed. Sensitivity studies show that uncertainties in input plasma parameters and thermal ion transport models are crucial for modelling mixed plasma discharges and increased D transport is required to reach the plasma composition consistent with diagnostic measurements at the plasma edge. Fast ion redistribution by a sawtooth instability is characterised by non-resonant transport due to reconnection of magnetic field lines and resonant transport caused by resonance interaction between the instability and fast ions. With ORBIT simulations it has been shown that resonant interaction strongly affects fast ions of high energies, like beam ions accelerated by RF waves and fusion products. For the considered case, fast ion profiles simulated by ORBIT remain peaked after the sawtooth crashes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Nonlinear dynamics and transport driven by energetic particle instabilities using a gyro-Landau closure model *

Abstract Energetic particle (EP) destabilized Alfvén eigenmode (AE) instabilities are simulated for a DIII-D experimental case with a pulsed neutral beam using a gyro-Landau moments model which introduces EP phase-mixing effects through closure relations. This provides a computationally efficient reduced model which is applied here in the nonlinear regime over timescales that would be difficult to address with more complete models. The long timescale nonlinear evolution and related collective transport losses are examined including the effects of zonal flow/current generation, nonlinear energy cascades, and EP profile flattening. The model predicts frequencies and mode structures that are consistent with experimental observations. These calculations address issues that have not been considered in previous modelling: the EP critical gradient profile evolution in the presence of zonal flows/currents, and the dynamical nature of the saturated state. A strong level of intermittency is present in the predicted instability-driven transport; this is connected to the zonal flow growth and decay cycles and nonlinear energy transfers. Simulation of intermittent AE-enhanced EP transport will be an important issue for the protection of plasma facing components in the next generation of fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗